Seismic behavior of capacity designed masonry walls in low seismicity regions

Eurocode 8 representing a new generation of structural design codes in Europe defines ‎requirements for the design of buildings against earthquake action. In Central and ‎Western Europe, the newly defined earthquake zones and corresponding design ground ‎acceleration values, will lead in many cases to earthquake actions which are remarkably ‎higher than those defined so far by the design codes used until now in Central Europe. ‎ In many cases, the weak points of masonry structures during an earthquake are the corner ‎regions of the walls. Loading of masonry walls by earthquake action leads in most cases ‎to high shear forces. The corresponding bending moment in such a wall typically causes a ‎significant increase of the eccentricity of the normal force in the critical wall cross ‎section. This in turn leads ultimately to a reduction of the size of the compression zone in ‎unreinforced walls and a high concentration of normal stresses and shear stresses in the ‎corner regions. ‎ Corner-Gap-Elements, consisting of a bearing beam located underneath the wall and ‎made of a sufficiently strong material (such as reinforced concrete), reduce the effect of ‎the eccentricity of the normal force and thus restricts the pinching effect of the ‎compression zone. In fact, the deformation can be concentrated in the joint below the ‎bearing beam. According to the principles of the Capacity Design philosophy, the ‎masonry itself is protected from high stresses as a potential cause of brittle failure. ‎ Shaking table tests at the NTU Athens Earthquake Engineering Laboratory have proven ‎the effectiveness of the Corner-Gap-Element. The following presentation will cover the ‎evaluation of various experimental results as well as a numerical modeling of the ‎observed phenomena.‎

Effects of red brick production on land use, household income, and greenhouse gas emissions in Khartoum, Sudan

In Khartoum (Sudan) a particular factor shaping urban land use is the rapid expansion of red brick making (BM) for the construction of houses which occurs on the most fertile agricultural Gerif soils along the Nile banks. The objectives of this study were to assess the profitability of BM, to explore the income distribution among farmers and kiln owners, to measure the dry matter (DM), nitrogen (N), phosphorus (P), potassium (K) and organic carbon (C_org) in cow dung used for BM, and to estimate the greenhouse gas (GHG) emissions from burned biomass fuel (cow dung and fuel wood). About 49 kiln owners were interviewed in 2009 using a semi-structured questionnaire that allowed to record socio-economic and variable cost data for budget calculations, and determination of Gini coefficients. Samples of cow dung were collected directly from the kilns and analyzed for their nutrients concentrations. To estimate GHG emissions a modified approach of the Intergovernmental Panel on Climate Change (IPCC) was used. The land rental value from red brick kilns was estimated at 5-fold the rental value from agriculture and the land rent to total cost ratio was 29% for urban farms compared to 6% for BM. The Gini coefficients indicated that income distribution among kiln owners was more equal than among urban farmers. Using IPCC default values the 475, 381, and 36 t DM of loose dung, compacted dung, and fuel wood used for BM emit annually 688, 548, and 60 t of GHGs, respectively.

Characteristics, socioeconomic benefits and household livelihoods of beef buffalo and beef cattle farming in Northeast Thailand

Since the Thai economy experiences rapid growth, agricultural systems, i.e. crop-livestock systems, are changing rapidly. On account of these changes, buffalo and cattle production has to be re-examined in terms of performance characteristics and roles of livestock for farm households in order to initiate suitable development programmes. Therefore, this study aimed to investigate the present characteristics of beef buffalo and beef cattle farms in Northeast Thailand. Using a semi-structured questionnaire, 121 randomly selected beef buffalo and beef cattle farms were interviewed in Nakhon Ratchasima province between October 2007 and May 2008. Both buffaloes and cattle were mostly integrated in mixed crop-livestock systems with medium to large farm sizes (7.9 ha), whereof less than half of the area was used for livestock. Family members were mainly responsible for the different activities of livestock farming and salaried labourers were only found on large-scale farms. The dominant roles of livestock were income generation to build up wealth or savings, the coverage of expected and unexpected expenses and earning of regular and additional income. Another important issue was the improvement of the social status, which increased with herd size. In order to improve farmers’ livelihoods and develop sustainable farming systems in Northeast Thailand the changing economic circumstances of cattle and especially buffalo production should receive more attention of researchers, governmental institutions and stakeholders.

Sensor-based Control of Chewing and Rumination Behavior of Dairy Cows

The measurement of feed intake, feeding time and rumination time, summarized by the term feeding behavior, are helpful indicators for early recognition of animals which show deviations in their behavior. The overall objective of this work was the development of an early warning system for inadequate feeding rations and digestive and metabolic disorders, which prevention constitutes the basis for health, performance, and reproduction. In a literature review, the current state of the art and the suitability of different measurement tools to determine feeding behavior of ruminants was discussed. Five measurement methods based on different methodological approaches (visual observance, pressure transducer, electrical switches, electrical deformation sensors and acoustic biotelemetry), and three selected measurement techniques (the IGER Behavior Recorder, the Hi-Tag rumination monitoring system and RumiWatchSystem) were described, assessed and compared to each other within this review. In the second study, the new system for measuring feeding behavior of dairy cows was evaluated. The measurement of feeding behavior ensues through electromyography (EMG). For validation, the feeding behavior of 14 cows was determined by both the EMG system and by visual observation. The high correlation coefficients indicate that the current system is a reliable and suitable tool for monitoring the feeding behavior of dairy cows. The aim of a further study was to compare the DairyCheck (DC) system and two additional measurement systems for measuring rumination behavior in relation to efficiency, reliability and reproducibility, with respect to each other. The two additional systems were labeled as the Lely Qwes HR (HR) sensor, and the RumiWatchSystem (RW). Results of accordance of RW and DC to each other were high. The last study examined whether rumination time (RT) is affected by the onset of calving and if it might be a useful indicator for the prediction of imminent birth. Data analysis referred to the final 72h before the onset of calving, which were divided into twelve 6h-blocks. The results showed that RT was significantly reduced in the final 6h before imminent birth.

Optimization of Processing Technology for Commercial Drying of Bananas (Matooke)

Summary - Cooking banana is one of the most important crops in Uganda; it is a staple food and source of household income in rural areas. The most common cooking banana is locally called matooke, a Musa sp triploid acuminate genome group (AAA-EAHB). It is perishable and traded in fresh form leading to very high postharvest losses (22-45%). This is attributed to: non-uniform level of harvest maturity, poor handling, bulk transportation and lack of value addition/processing technologies, which are currently the main challenges for trade and export, and diversified utilization of matooke. Drying is one of the oldest technologies employed in processing of agricultural produce. A lot of research has been carried out on drying of fruits and vegetables, but little information is available on matooke. Drying of matooke and milling it to flour extends its shelf-life is an important means to overcome the above challenges. Raw matooke flour is a generic flour developed to improve shelf stability of the fruit and to find alternative uses. It is rich in starch (80 - 85%db) and subsequently has a high potential as a calorie resource base. It possesses good properties for both food and non-food industrial use. Some effort has been done to commercialize the processing of matooke but there is still limited information on its processing into flour. It was imperative to carry out an in-depth study to bridge the following gaps: lack of accurate information on the maturity window within which matooke for processing into flour can be harvested leading to non-uniform quality of matooke flour; there is no information on moisture sorption isotherm for matooke from which the minimum equilibrium moisture content in relation to temperature and relative humidity is obtainable, below which the dry matooke would be microbiologically shelf-stable; and lack of information on drying behavior of matooke and standardized processing parameters for matooke in relation to physicochemical properties of the flour. The main objective of the study was to establish the optimum harvest maturity window and optimize the processing parameters for obtaining standardized microbiologically shelf-stable matooke flour with good starch quality attributes. This research was designed to: i) establish the optimum maturity harvest window within which matooke can be harvested to produce a consistent quality of matooke flour, ii) establish the sorption isotherms for matooke, iii) establish the effect of process parameters on drying characteristics of matooke, iv) optimize the drying process parameters for matooke, v) validate the models of maturity and optimum process parameters and vi) standardize process parameters for commercial processing of matooke. Samples were obtained from a banana plantation at Presidential Initiative on Banana Industrial Development (PIBID), Technology Business Incubation Center (TBI) at Nyaruzunga – Bushenyi in Western Uganda. A completely randomized design (CRD) was employed in selecting the banana stools from which samples for the experiments were picked. The cultivar Mbwazirume which is soft cooking and commonly grown in Bushenyi was selected for the study. The static gravitation method recommended by COST 90 Project (Wolf et al., 1985), was used for determination of moisture sorption isotherms. A research dryer developed for this research. All experiments were carried out in laboratories at TBI. The physiological maturity of matooke cv. mbwazirume at Bushenyi is 21 weeks. The optimum harvest maturity window for commercial processing of matooke flour (Raw Tooke Flour - RTF) at Bushenyi is between 15-21 weeks. The finger weight model is recommended for farmers to estimate harvest maturity for matooke and the combined model of finger weight and pulp peel ratio is recommended for commercial processors. Matooke isotherms exhibited type II curve behavior which is characteristic of foodstuffs. The GAB model best described all the adsorption and desorption moisture isotherms. For commercial processing of matooke, in order to obtain a microbiologically shelf-stable dry product. It is recommended to dry it to moisture content below or equal to 10% (wb). The hysteresis phenomenon was exhibited by the moisture sorption isotherms for matooke. The isoteric heat of sorption for both adsorptions and desorption isotherms increased with decreased moisture content. The total isosteric heat of sorption for matooke: adsorption isotherm ranged from 4,586 – 2,386 kJ/kg and desorption isotherm from 18,194– 2,391 kJ/kg for equilibrium moisture content from 0.3 – 0.01 (db) respectively. The minimum energy required for drying matooke from 80 – 10% (wb) is 8,124 kJ/kg of water removed. Implying that the minimum energy required for drying of 1 kg of fresh matooke from 80 - 10% (wb) is 5,793 kJ. The drying of matooke takes place in three steps: the warm-up and the two falling rate periods. The drying rate constant for all processing parameters ranged from 5,793 kJ and effective diffusivity ranged from 1.5E-10 - 8.27E-10 m2/s. The activation energy (Ea) for matooke was 16.3kJ/mol (1,605 kJ/kg). Comparing the activation energy (Ea) with the net isosteric heat of sorption for desorption isotherm (qst) (1,297.62) at 0.1 (kg water/kg dry matter), indicated that Ea was higher than qst suggesting that moisture molecules travel in liquid form in matooke slices. The total color difference (ΔE*) between the fresh and dry samples, was lowest for effect of thickness of 7 mm, followed by air velocity of 6 m/s, and then drying air temperature at 70˚C. The drying system controlled by set surface product temperature, reduced the drying time by 50% compared to that of a drying system controlled by set air drying temperature. The processing parameters did not have a significant effect on physicochemical and quality attributes, suggesting that any drying air temperature can be used in the initial stages of drying as long as the product temperature does not exceed gelatinization temperature of matooke (72˚C). The optimum processing parameters for single-layer drying of matooke are: thickness = 3 mm, air temperatures 70˚C, dew point temperature 18˚C and air velocity 6 m/s overflow mode. From practical point of view it is recommended that for commercial processing of matooke, to employ multi-layer drying of loading capacity equal or less than 7 kg/m², thickness 3 mm, air temperatures 70˚C, dew point temperature 18˚C and air velocity 6 m/s overflow mode.

How Death Guides Human Behavior - The Role of Cultural Norms and Values in Terror Management Theory

Die Dissertation besteht im Wesentlichen aus zwei Teilen: der Synopse und einem empirischen Teil. In der Synopse werden die Befunde aus dem empirischen Teil zusammengefasst und mit der bisherigen Forschungsliteratur in Zusammenhang gesetzt. Im empirischen Teil werden alle Studien, die für diese Dissertation durchgeführt wurden, in Paper-Format berichtet. Im ersten Teil der Synopse werden grundlegende Annahmen der Terror Management Theorie (TMT) dargelegt—mit besonderem Schwerpunkt auf die Mortalitätssalienz (MS)-Hypothese, die besagt, dass die Konfrontation mit der eigenen Sterblichkeit die Motivation erhöht das eigene Weltbild zu verteidigen und nach Selbstwert zu streben. In diesem Kontext wird auch die zentrale Rolle von Gruppen erklärt. Basierend auf diesen beiden Reaktionen, wird TMT Literatur angeführt, die sich auf bestimmte kulturelle Werte und soziale Normen bezieht (wie prosoziale und pro-Umwelt Normen, materialistische und religiöse Werte, dem Wert der Ehrlichkeit, die Norm der Reziprozität und deskriptive Normen). Darüber hinaus werden Randbedingungen, wie Gruppenmitgliedschaft und Norm-Salienz, diskutiert. Zuletzt folgt eine Diskussion über die Rolle von Gruppen, der Funktion des Selbstwerts und über Perspektiven einer friedlichen Koexistenz. Der empirische Teil enthält elf Studien, die in acht Papern berichtet werden. Das erste Paper behandelt die Rolle von Gruppenmitgliedschaft unter MS, wenn es um die Bewertung von anderen geht. Das zweite Manuskript geht der Idee nach, dass Dominanz über andere für Sadisten eine mögliche Quelle für Selbstwert ist und daher unter MS verstärkt ausgeübt wird. Das dritte Paper untersucht prosoziales Verhalten in einer Face-to-Face Interaktion. Im vierten Paper wird gezeigt, dass Personen (z.B. Edward Snowden), die im Namen der Wahrheit handeln, unter MS positiver bewertet werden. Im fünften Paper zeigen zwei Studien, dass MS dazu führt, dass mögliche gelogene Aussagen kritischer beurteilt werden. Das sechste Paper zeigt, dass der Norm der Reziprozität unter MS stärker zugestimmt wird. Das siebte Paper geht der Frage nach, inwiefern MS das Einhalten dieser Norm beeinflusst. Und schließlich wird im achten Paper gezeigt, dass MS die Effektivität der Door-in-the-Face Technik erhöht—eine Technik, die auf der Norm der Reziprozität basiert.

Punching Shear Behavior of UHPC Flat Slabs

At the Institute of Structural Engineering of the Faculty of Civil Engineering, Kassel University, series tests of slab-column connection were carried out, subjected to concentrated punching load. The effects of steel fiber content, concrete compressive strength, tension reinforcement ratio, size effect, and yield stress of tension reinforcement were studied by testing a total of six UHPC slabs and one normal strength concrete slab. Based on experimental results; all the tested slabs failed in punching shear as a type of failure, except the UHPC slab without steel fiber which failed due to splitting of concrete cover. The post ultimate load-deformation behavior of UHPC slabs subjected to punching load shows harmonic behavior of three stages; first, drop of load-deflection curve after reaching maximum load, second, resistance of both steel fibers and tension reinforcement, and third, pure tension reinforcement resistance. The first shear crack of UHPC slabs starts to open at a load higher than that of normal strength concrete slabs. Typically, the diameter of the punching cone for UHPC slabs on the tension surface is larger than that of NSC slabs and the location of critical shear crack is far away from the face of the column. The angle of punching cone for NSC slabs is larger than that of UHPC slabs. For UHPC slabs, the critical perimeter is proposed and located at 2.5d from the face of the column. The final shape of the punching cone is completed after the tension reinforcement starts to yield and the column stub starts to penetrate through the slab. A numerical model using Finite Element Analysis (FEA) for UHPC slabs is presented. Also some variables effect on punching shear is demonstrated by a parametric study. A design equation for UHPC slabs under punching load is presented and shown to be applicable for a wide range of parametric variations; in the ranges between 40 mm to 300 mm in slab thickness, 0.1 % to 2.9 % in tension reinforcement ratio, 150 MPa to 250 MPa in compressive strength of concrete and 0.1 % to 2 % steel fiber content. The proposed design equation of UHPC slabs is modified to include HSC and NSC slabs without steel fiber, and it is checked with the test results from earlier researches.

Does interpersonal behavior of psychotherapy trainees differ in private and professional relationships?

• Aim: The present study aimed to evaluate the effect of trainees’ interpersonal behavior on work involvement (WI) and compared their social behavior within professional and private relationships as well as between different psychotherapeutic orientations. • Methods: The interpersonal scales of the Intrex short-form questionnaire and the Work Involvement Scale (WIS) were used to evaluate two samples of German psychotherapy trainees in psychoanalytic, psychodynamic, and cognitive behavioral therapy training. Trainees from Sample 1 (N = 184) were asked to describe their interpersonal behavior in relation to their patients when filling out the Intrex, whereas trainees from Sample 2 (N = 135) were asked to describe the private relationship with a significant other. • Results: Interpersonal affiliation in professional relationships significantly predicted the level of healing involvement, while stress involvement was predicted by interpersonal affiliation and interdependence in trainees’ relationships with their patients. Social behavior within professional relationships provided higher correlations with WI than private interpersonal behavior. Significant differences were found between private and professional relation settings in trainees’ interpersonal behavior with higher levels of affiliation and interdependence with significant others. Differences between therapeutic orientation and social behavior could only be found when comparing trainees’ level of interdependence with the particular relationship setting. • Conclusion: Trainees’ interpersonal level of affiliation in professional relationships is a predictor for a successful psychotherapeutic development. Vice versa, controlling behavior in professional settings can be understood as a risk factor against psychotherapeutic growth. Both results strengthen an evidence-based approach for competence development during psychotherapy training.

Institutions, Behavior and Evolution

The three articles constituting this thesis are for reasons of content or method related to the following three fields in economics: Behavioral Economics, Evolutionary Game Theory and Formal Institutional Economics. A core element of these fields is the concept of individual preferences. Preferences are of central importance for the conceptional framework to analyze human behavior. They form the foundation for the theory of rational choice which is defined by the determination of the choice set and the selection of the most preferred alternative according to some consistency requirements. The theory of rational choice is based on a very simplified description of the problem of choice (object function and constraints). However, that choices depend on many more factors is for instance propagated by psychological theories and is supported by many empirical and experimental studies. This thesis adds to a better understanding of individual behavior to the extent that the evolution of certain characteristics of preferences and their consequences on human behavior forms the overarching theme of the dissertation. The long-term effect of evolutionary forces on a particular characteristic of importance in the theoretical, empirical and experimental economic literature, the concept of inequality aversion, is subject of the article “The evolution of inequality aversion in a simplified game of life” (Chapter 4). The contribution of the article is the overcoming of a restriction of former approaches to analyze the evolution of preferences in very simple environments. By classifying human interaction into three central economic games, the article provides a first step towards a simplified and sufficiently complete description of the interaction environment. Within such an environment the article characterizes the evolutionary stable preference distribution. One result shows, that the interaction of the aforementioned three classes can stabilize a preference of inequality aversion in the subpopulation which is favored in the problem of redistribution. The two remaining articles are concerned with social norms, which dissemination is determined by medium-run forces of cultural evolution. The article “The impact of market innovations on the evolution of social norms: the sustainability case.“ (Chapter 2) studies the interrelation between product innovations which are relevant from a sustainability perspective and an according social norm in consumption. This relation is based on a conformity bias in consumption and the attempt to avoid cognitive dissonances resulting from non-compliant consumption. Among others, it is shown that a conformity bias on the consumption side can lead to multiple equilibria on the side of norm adoption. The article “Evolution of cooperation in social dilemmas: signaling internalized norms.” (Chapter 3) studies the emergence of cooperation in social dilemmas based on the signaling of social norms. The article provides a potential explanation of cooperative behavior, which does not rely on the assumption of structured populations or on the unmotivated ability of social norms to restrict individual actions or strategy spaces. A comprehensive result of the single articles is the explanation of the phenomenon of partial norm adaption or dissemination of preferences. The plurality of the applied approaches with respect to the proximity to the rational choice approach and regarding the underlying evolutionary mechanics is a particular strength of the thesis. It shows the equality of these approaches in their potential to explain the phenomenon of cooperation in environments that provide material incentives for defective behavior. This also points to the need of a unified framework considering the biological and cultural coevolution of preference patterns.

Accuracy of outcome anticipation, but not gaze behavior, differs against left- and right-handed penalties in team-handball goalkeeping

Low perceptual familiarity with relatively rarer left-handed as opposed to more common right-handed individuals may result in athletes' poorer ability to anticipate the former's action intentions. Part of such left-right asymmetry in visual anticipation could be due to an inefficient gaze strategy during confrontation with left-handed individuals. To exemplify, observers may not mirror their gaze when viewing left- vs. right-handed actions but preferentially fixate on an opponent's right body side, irrespective of an opponent's handedness, owing to the predominant exposure to right-handed actions. So far empirical verification of such assumption, however, is lacking. Here we report on an experiment where team-handball goalkeepers' and non-goalkeepers' gaze behavior was recorded while they predicted throw direction of left- and right-handed 7-m penalties shown as videos on a computer monitor. As expected, goalkeepers were considerably more accurate than non-goalkeepers and prediction was better against right- than left-handed penalties. However, there was no indication of differences in gaze measures (i.e., number of fixations, overall and final fixation duration, time-course of horizontal or vertical fixation deviation) as a function of skill group or the penalty-takers' handedness. Findings suggest that inferior anticipation of left-handed compared to right-handed individuals' action intentions may not be associated with misalignment in gaze behavior. Rather, albeit looking similarly, accuracy differences could be due to observers' differential ability of picking up and interpreting the visual information provided by left- vs. right-handed movements.

An analysis of household farm investment decisions under varying land tenure arrangements in Ghana

Land tenure insecurity is widely perceived as a disincentive for long-term land improvement investment hence the objective of this paper is to evaluate how tenure (in)security associated with different land use arrangements in Ghana influenced households’ plot level investment decisions and choices. The paper uses data from the Farmer-Based Organisations (FBO) survey. The FBO survey collected information from 2,928 households across three ecological zones of Ghana using multistaged cluster sampling. Probit and Tobit models tested the effects of land tenancy and ownership arrangements on households’ investment behaviour while controlling other factors. It was found that marginal farm size was inversely related to tenure insecurity while tenure insecurity correlate positively with value of farm land and not farm size. Individual ownership and documentation of land significantly reduced the probability of households losing uncultivated lands. Individual land ownership increased both the probability of investing and level of investments made in land improvement and irrigation probably due to increasing importance households place on land ownership. Two possible explanations for this finding are: First, that land markets and land relations have changed significantly over the last two decades with increasing money transaction and fixed agreements propelled by population growth and increasing value of land. Secondly, inclusion of irrigation investment as a long term investment in land raises the value of household investment and the time period required to reap the returns on the investments. Households take land ownership and duration of tenancy into consideration if the resource implications of land investments are relatively huge and the time dimension for harvesting returns to investments is relatively long.

Optimising contributions of goat farming to household economic success and food security in three production systems in Ethiopia

The study aims to analyse factors affecting contributions of goat farming to household economic success and food security in three goat production systems of Ethiopia. A study was conducted in three districts of Ethiopia representing arid agro-pastoral (AAP), semi-arid agro-pastoral (SAAP) and highland mixed crop-livestock (HMCL) systems involving 180 goat keeping households. Gross margin (GM) and net benefit (NB1 and NB2) were used as indicators of economic success of goat keeping. NB1 includes in-kind benefits of goats (consumption and manure), while NB2 additionally constitutes intangible benefits (insurance and finance). Household dietary diversity score (HDDS) was used as a proxy indicator of food security. GM was significantly affected by an off-take rate and flock size interaction (P<0.001). The increment of GM due to increased off-take rate was more prominent for farmers with bigger flocks. Interaction between flock size and production system significantly (P<0.001) affected both NB1 and NB2. The increment of NB1 and NB2 by keeping larger flocks was higher in AAP system, due to higher in-kind and intangible benefits of goats in this system. Effect of goat flock size as a predictor of household dietary diversity was not significant (P>0.05). Nevertheless, a significant positive correlation (P<0.05) was observed between GM from goats and HDDS in AAP system, indicating the indirect role of goat production for food security. The study indicated that extent of utilising tangible and intangible benefits of goats varied among production systems and these differences should be given adequate attention in designing genetic improvement programs.