Effects of activated charcoal and quebracho tannins on the turnover of goat manure in irrigated organic agriculture of the subtropics

Agriculture in semi-arid and arid regions is constantly gaining importance for the security of the nutrition of humankind because of the rapid population growth. At the same time, especially these regions are more and more endangered by soil degradation, limited resources and extreme climatic conditions. One way to retain soil fertility under these conditions in the long run is to increase the soil organic matter. Thus, a two-year field experiment was conducted to test the efficiency of activated charcoal and quebracho tannin extract as stabilizers of soil organic matter on a sandy soil low in nutrients in Northern Oman. Both activated charcoal and quebracho tannin extract were either fed to goats and after defecation applied to the soil or directly applied to the soil in combination with dried goat manure. Regardless of the application method, both additives reduced decomposition of soil-applied organic matter and thus stabilized and increased soil organic carbon. The nutrient release from goat manure was altered by the application of activated charcoal and quebracho tannin extract as well, however, nutrient release was not always slowed down. While activated charcoal fed to goats, was more effective in stabilising soil organic matter and in reducing nutrient release than mixing it, for quebracho tannin extract the opposite was the case. Moreover, the efficiency of the additives was influenced by the cultivated crop (sweet corn and radish), leading to unexplained interactions. The reduced nutrient release caused by the stabilization of the organic matter might be the reason for the reduced yields for sweet corn caused by the application of manure amended with activated charcoal and quebracho tannin extract. Radish, on the other hand, was only inhibited by the presence of quebracho tannin extract but not by activated charcoal. This might be caused by a possible allelopathic effect of tannins on crops. To understand the mechanisms behind the changes in manure, in the soil, in the mineralisation and the plant development and to resolve detrimental effects, further research as recommended in this dissertation is necessary. Particularly in developing countries poor in resources and capital, feeding charcoal or tannins to animals and using their faeces as manure may be promising to increase soil fertility, sequester carbon and reduce nutrient losses, when yield reductions can be resolved.

Analysis of the Market Potential of Syrian Organic Fruit and Vegetables for Exports to Germany

Syria has been a major producer and exporter of fresh fruit and vegetables (FFV) in the Arabic region. Prior to 2011, Syrian FFV were mainly exported to the neighbouring countries, the Gulf States and Northern Africa as well as to Eastern European countries. Although the EU is potentially one of the most profitable markets of high quality FFV (such as organic ones) in the world, Syrian exports of FFV to Western European countries like Germany have been small. It could be a lucrative opportunity for Syrian growers and exporters of FFV to export organic products to markets such as Germany, where national production is limited to a few months due to climatic conditions. Yet, the organic sector in Syria is comparatively young and only a very small area of FFV is certified according to EU organic regulations. Up to the author’s knowledge, little was known about Syrian farmers’ attitudes towards organic FFV production. There was also no study so far that explored and analysed the determining factors for organic FFV adoption among Syrian farmers as well as the exports of these products to the EU markets. The overarching aim of the present dissertation focused on exploring and identifying the market potential of Syrian exports of organic FFV to Germany. The dissertation was therefore concerned with three main objectives: (i) to explore if German importers and wholesalers of organic FFV see market opportunities for Syrian organic products and what requirements in terms of quality and quantity they have, (ii) to determine the obstacles Syrian producers and exporters face when exporting agricultural products to Germany, and (iii) to investigate whether Syrian farmers of FFV can imagine converting their farms to organic production as well as the underlying reasons why they do so or not. A twofold methodological approach with expert interviews and a farmer survey were used in this dissertation to address the abovementioned objectives. While expert interviews were conducted with German and Syrian wholesalers of (organic) FFV in 2011 (9 interviews each), the farmer survey was administrated with 266 Syrian farmers of FFV in the main region for the production of FFV (i.e. the coastal region) from November 2012 till May 2013. For modelling farmers’ decisions to adopt organic farming, the Theory of Planned Behaviour as theoretical framework and Partial Least Squares Structural Equation Modelling as the main method for data analysis were used in this study. The findings of this dissertation yield implications for the different stakeholders (governmental institutions and NGOs, farmers, exporters, wholesalers, etc.) who are interested in prompting the Syrian export of organic products. Based on the empirical results and a literature review, an action plan to promote Syrian production and export of organic products was developed which can help in the post-war period in Syria at improving the organic sector.

Fliesslochformen und Gewindefurchen in dünne Bleche und Rohre aus Kupfer und Kupferlegierungen

This thesis in Thermal Flow Drilling and Flowtap in thin metal sheet and pipes of copper and copper alloys had as objectives to know the comportment of copper and copper alloys sheet metal during the Thermal Flow Drill processes with normal tools, to know the best Speed and Feed machine data for the best bushing quality, to known the best Speed for Form Tapping processes and to know the best bush long in pure copper pipes for water solar interchange equipment. Thermal Flow Drilling (TFD) and Form Tapping (FT) is one of the research lines of the Institute of Production and Logistics (IPL) at University of Kassel. At December 1995, a work meeting of IPL, Santa Catarina University, Brazil, Buenos Aires University, Argentine, Tarapacá University (UTA), Chile members and the CEO of Flowdrill B.V. was held in Brazil. The group decided that the Manufacturing Laboratory (ML) of UTA would work with pure copper and brass alloys sheet metal and pure copper pipes in order to develop a water interchange solar heater. The Flowdrill BV Company sent tools to Tarapacá University in 1996. In 1999 IPL and the ML carried out an ALECHILE research project promoted by the DAAD and CONICyT in copper sheet metal and copper pipes and sheet metal a-brass alloys. The normal tools are lobed, conical tungsten carbide tool. When rotated at high speed and pressed with high axial force into sheet metal or thin walled tube generated heat softens the metal and allows the drill to feed forward produce a hole and simultaneously form a bushing from the displacement material. In the market exist many features but in this thesis is used short and longs normal tools of TFD. For reach the objectives it was takes as references four qualities of the frayed end bushing, where the best one is the quality class I. It was used pure copper and a-brass alloys sheet metals, with different thickness. It was used different TFD drills diameter for four thread type, from M-5 to M10. Similar to the Aluminium sheet metals studies it was used the predrilling processes with HSS drills around 30% of the TFD diameter (1,5 – 3,0 mm D). In the next step is used only 2,0 mm thick metal sheet, and 9,2 mm TFD diameter for M-10 thread. For the case of pure commercial copper pipes is used for ¾” inch diameter and 12, 8 mm (3/8”) TFD drill for holes for 3/8” pipes and different normal HSS drills for predrilling processes. The chemical sheet metal characteristics were takes as reference for the material behaviour. The Chilean pure copper have 99,35% of Cu and 0,163% of Zinc and the Chilean a-brass alloys have 75,6% of Cu and 24,0% of Zinc. It is used two German a-brass alloys; Nº1 have 61,6% of Cu, 36,03 % of Zinc and 2,2% of Pb and the German a-brass alloys Nº2 have 63,1% of Cu, 36,7% of Zinc and 0% of Pb. The equipments used were a HAAS CNC milling machine centre, a Kistler dynamometer, PC Pentium II, Acquisition card, TESTPOINT and XAct software, 3D measurement machine, micro hardness, universal test machine, and metallographic microscope. During the test is obtained the feed force and momentum curves that shows the material behaviour with TFD processes. In general it is take three phases. It was possible obtain the best machining data for the different sheet of copper and a-brass alloys thick of Chilean materials and bush quality class I. In the case of a-brass alloys, the chemical components and the TFD processes temperature have big influence. The temperature reach to 400º Celsius during the TFD processes and the a-brass alloys have some percents of Zinc the bush quality is class I. But when the a-brass alloys have some percents of Lead who have 200º C melting point is not possible to obtain a bush, because the Lead gasify and the metallographic net broke. During the TFD processes the recrystallization structures occur around the Copper and a-brass alloy bush, who gives more hardness in these zones. When the threads were produce with Form Tapping processes with Flowtap tools, this hardness amount gives a high limit load of the thread when hey are tested in a special support that was developed for it. For eliminated the predrilling processes with normal HSS drills it was developed a compound tool. With this new tool it was possible obtain the best machining data for quality class I bush. For the copper pipes it is made bush without predrilling and the quality class IV was obtained. When it is was used predrilling processes, quality classes I bush were obtained. Then with different HSS drill diameter were obtained different long bush, where were soldering with four types soldering materials between pipes with 3/8” in a big one as ¾”. Those soldering unions were tested by traction test and all the 3/8” pipes broken, and the soldering zone doesn’t have any problem. Finally were developed different solar water interchange heaters and tested. As conclusions, the present Thesis shows that the Thermal Flow Drilling in thinner metal sheets of cooper and cooper alloys needs a predrilling process for frayed end quality class I bushings, similar to thinner sheets of aluminium bushes. The compound tool developed could obtain quality class I bushings and excludes predrilling processes. The bush recrystalization, product of the friction between the tool and the material, the hardness grows and it is advantageous for the Form Tapping. The methodology developed for commercial copper pipes permits to built water solar interchange heaters.

Simulative Risikoanalyse von Biomethanprojekten

Im Zuge der Novellierung der Gasnetzzugangsverordnung sowie des Erneuerbare-Energien-Gesetzes entwickelte sich die Einspeisung von Biomethan in das Erdgasnetz als alternative Investitionsmöglichkeit der Erneuerbare-Energien-Branche. Als problematisch erweist sich dabei die Identifikation und Strukturierung einzelner Risikofaktoren zu einem Risikobereich, sowie die anschließende Quantifizierung dieser Risikofaktoren innerhalb eines Risikoportfolios. Darüber hinaus besteht die Schwierigkeit, diese Risikofaktoren in einem cashflowbasierten und den Ansprüchen der Investoren gewachsenem Risikomodell abzubilden. Zusätzlich müssen dabei Wechselwirkungen zwischen einzelnen Risikofaktoren berücksichtigt werden. Aus diesem Grund verfolgt die Dissertation das Ziel, die Risikosituation eines Biomethanprojektes anhand aggregierter und isolierter Risikosimulationen zu analysieren. Im Rahmen einer Diskussion werden Strategien und Instrumente zur Risikosteuerung angesprochen sowie die Implementierungsfähigkeit des Risikomodells in das Risikomanagementsystem von Investoren. Die Risikomaße zur Beschreibung der Risikoauswirkung betrachten die Shortfälle einer Verteilung. Dabei beziehen sich diese auf die geplanten Ausschüttungen sowie interne Verzinsungsansprüche der Investoren und die von Kreditinstituten geforderte minimale Schuldendienstdeckungsrate. Im Hinblick auf die Risikotragfähigkeit werden liquiditätsorientierte Kennzahlen hinzugezogen. Investoren interessieren sich vor dem Hintergrund einer gezielten Risikosteuerung hauptsächlich für den gefahrvollsten Risikobereich und innerhalb dessen für den Risikofaktor, der die größten Risikoauswirkungen hervorruft. Zudem spielt der Zeitpunkt maximaler Risikoauswirkung eine große Rolle. Als Kernaussage dieser Arbeit wird festgestellt, dass in den meisten Fällen die Aussagefähigkeit aggregierter Risikosimulationen durch Überlagerungseffekte negativ beeinträchtigt wird. Erst durch isoliert durchgeführte Risikoanalysen können diese Effekte eliminiert werden. Besonders auffällig gestalten sich dabei die Ergebnisse der isoliert durchgeführten Risikoanalyse des Risikobereichs »Politik«. So verursacht dieser im Vergleich zu den übrigen Risikobereichen, wie »Infrastruktur«, »Rohstoffe«, »Absatzmarkt« und »Finanzmarkt«, die geringsten Wahrscheinlichkeiten avisierte Planwerte der Investoren zu unterschreiten. Kommt es jedoch zu einer solchen Planwert-Unterschreitung, nehmen die damit verbundenen Risikoauswirkungen eine überraschende Position im Risikoranking der Investoren ein. Hinsichtlich der Aussagefähigkeit des Risikomodells wird deutlich, dass spezifische Risikosichtweisen der Investoren ausschlaggebend dafür sind, welche Strategien und Instrumente zur Risikosenkung umgesetzt werden. Darüber hinaus wird festgestellt, dass die Grenzen des Risikomodells in der Validität der Expertenmeinungen und dem Auffinden einer Optimallösung zu suchen sind.

A Comparative Study on Internationalization and the Role of International Offices at Selected Middle Eastern and German Universities

Internationalization of higher education has become one of the most important policies for institutions of higher education worldwide. Though universities are international by nature, the need for intensified quality activities of international nature has promoted internationalization to be under spotlight of researchers, administrators and policy makers and to be an area for research. Each institution follows its certain way to govern its international affairs. Most Universities, especially in the 'Developed World' started to plan it strategically. This study explores the meanings and importance of internationalization especially that it means different things to different people. It also studies the rationales behind internationalizing higher education. It focuses on the four main prevailing rationales; political, cultural/social, economic/financial, and academic on both national and institutional levels. With the increasing need to strategically plan, the study explores internationalization strategies in terms of how to develop them, what are their approaches and types, and their components and dimensions. Damascus University has witnessed an overwhelming development of its international relations and activities. Therefore, it started to face a problem of how to deal with this increasing load especially that its International Office is the only unit that deals with the international issues. In order to study the internationalization phenomenon at Damascus University, the 2WH approach, which asks the what, why, and how questions, is used and in order to define the International Office's role in the internationalization process of the University, it studies it and the international offices of Kassel University, and Humboldt University in Germany, The University of Jordan, and Al Baath University in Syria using the 'SOCIAL' approach that studies and analyses the situation, organization, challenges, involvement, ambitions, and limitations of these offices. The internationalization process at the above-mentioned Universities is studied and compared in terms of its meaning, rationales for both the institution and its academic staff, challenges and strategic planning. Then a comparison is made among the international offices of the Universities to identify their approaches, what led to their success and what led to their failure in their practices. The aim is to provide Damascus University and its International Office with some good practices and, depending on the experiences of the professionals of the case-studies, a suggested guidance to the work of this Office and the University in general is given. The study uses the interviews with the different officials and stakeholders of the case-studies as the main method of collecting the information in addition to site visits, studying their official documents and their websites. The study belongs to qualitative research that has an action dimension in it since the recommendations will be applied in the International Office. The study concludes with few learned lessons for Damascus University and its International Office depending on the comparison that was done according to a set of dimensions. Finally a reflection on the relationship between internationalization of higher education and politics, the impact of politics on Middle Eastern Universities, and institutional internationalization strategies are presented.