An Inquiry of Changes in Environmental Governance by Community-driven Process

Urban environmental depletion has been a critical problem among industrialized-transformed societies, especially at the local level where administrative authorities’ capacity lags behind changes. Derived from governance concept, the idea of civil society inclusion is highlighted. Focusing on an agglomerated case study, Bang Plee Community in Thailand, this research investigates on a non-state sector, 201-Community organization, as an agent for changes to improve urban environments on solid waste collection. Two roles are contested: as an agent for neighborhood internal change and as an intermediary toward governance changes in state-civil society interaction. By employing longitudinal analysis via a project intervention as research experiment, the outcomes of both roles are detected portrayed in three spheres: state, state-civil society interaction, and civil society sphere. It discovers in the research regarding agglomerated context that as an internal changes for environmental betterment, 201-Community organization operation brings on waste reduction at the minimal level. Community-based organization as an agent for changes – despite capacity input it still limited in efficiency and effectiveness – can mobilize fruitfully only at the individual and network level of civil society sectors, while fails managing at the organizational level. The positive outcomes result by economic waste incentive associated with a limited-bonded group rather than the rise of awareness at large. As an intermediary agent for shared governance, the community-based organization cannot bring on mutual dialogue with state as much as cannot change the state’s operation arena of solid waste management. The findings confine the shared governance concept that it does not applicable in agglomerated locality as an effective outcome, both in terms of being instrumental toward civil society inclusion and being provocative of internal change. Shared environmental governance as summarized in this research can last merely a community development action. It distances significantly from civil society inclusion and empowerment. However, the research proposes that community-based environmental management and shared governance toward civil society inclusion in urban environmental improvement are still an expectable option and reachable if their factors and conditions of key success and failure are intersected with a particular context. Further studies demand more precise on scale, scope, and theses factors of environmental management operation operated by civil society sectors.

Lehrende als ‘agents of change’ - Konzeptionelle Überlegungen zu einer kinderrechtlichen Annotation und Ausdeutung der Standards für die Lehrerbildung

Die Dissertation geht von der Überlegung aus, dass ein Wandel im deutschen Bildungssystem aufgrund kinderrechtlicher und demokratischer Überlegungen eine essenzielle Zukunftsaufgabe ist. Dies geschieht im Besonderen vor dem Hintergrund kinderrechtlicher Forderungen, wie sie beispielsweise aus dem Status Deutschlands als Mitgliedsland der UN-Kinderrechtskonvention und des UN-Übereinkommens über die Rechte von Menschen mit Behinderung entstehen: Die Korrelation zwischen Herkunft und Bildungserfolg sowie die noch konzeptionell ungenügend entwickelten Ansätze zur Inklusion werden als bestimmend für die Diskussion erkannt. Die Arbeit vertritt die These, dass Lehrende eine zentrale Rolle in einem notwendigen Prozess der Umwandlung des deutschen Bildungssystems spielen können und nimmt in emanzipatorischer Absicht die Lehrenden als Zielgruppe in den Blick. Aufgrund der Struktur der Lehrendenausbildung wird zudem dafür argumentiert, entsprechende Veränderungen im Sinne ihrer Nachhaltigkeit und flächendeckenden Relevanz in der Lehrendenausbildung des ersten universitären Ausbildungsabschnittes zu verankern. Als Instrument, welches die Kriterien von Nachhaltigkeit und umfassender Relevanz erfüllt, werden die Standards für die Lehrerbildung im Bereich Bildungswissenschaften benannt und theoretisch unterfüttert. Grundsätzlich spannt sich der Blickwinkel der Arbeit zwischen der Betrachtung der Struktur des Bildungssystems, des Wissens und Könnens von Lehrenden und Lernenden im Sinne der Kompetenzorientierung sowie der Haltung auf, welche Lehrende einnehmen. Dabei wird aufgezeigt, dass sich diese Faktoren wechselseitig auf vielfache Art und Weise beeinflussen. Auf der Basis dieser Überlegungen wird zunächst das deutsche Bildungssystem in seinen Strukturen beschrieben und die Lehrenden und Lernenden als Teilnehmende am Bildungsgeschehen skizziert. Ein exkursiver Vergleich dreier aufgrund kinderrechtlicher Parameter ausgewählter europäischer Bildungssysteme eruiert zudem, inwiefern die aufgezeigten Bestimmungsgrößen Struktur, Wissen/Können und Haltung Einfluss auf kinderrechtliche Verfasstheit des Bildungssystems nehmen, wobei die Grundprinzipien der UN-Kinderrechtskonvention hier als Messinstrument dienen. Davon ausgehend, erscheint pädagogische Haltung als eine wesentliche Einflussgröße, die im weiteren Verlauf der Arbeit im Sinne der kritischen Pädagogik zu einer Konzeption Pädagogischer Verantwortung verdichtet wird. Vor diesem Hintergrund erfolgt eine Betrachtung aktueller Problematiken im deutschen Bildungssystem, die sich an den in den Standards für die Lehrerbildung identifizierten Ausbildungsschwerpunkten orientiert und erneut die Prinzipien und rechtlichen Vorgaben der UN-Kinderrechtskonvention als Maßstab wählt. Auf der Grundlage dieser umfassenden Diskussion werden in einem sich anschließenden Analyseschritt Annotationen vorgenommen, die die Formulierungen der 11 Standards für die Lehrerbildung inhaltlich erweitern und ergänzen. In Verbindung mit einer Pädagogischen Verantwortung, die sich der Ausbildung kritischer Mündigkeit verpflichtet, werden die annotierten Standards als eine Möglichkeit der kinderrechtlichen (Selbst-)Evaluation von Lehrenden sowie als Instrument einer kinderrechtliche Gesichtspunkte fokussierenden Lehrendenbildung verstanden und dargestellt.

Entwicklung der Windenergietechnik in Deutschland und der Einfluss staatlicher Förderpolitik - Technikentwicklung in den 90er Jahren zwischen Markt und Forschungsförderung

Seit gut zehn Jahren erlebt die Windenergienutzung in Deutschland einen in der Mitte der 80er Jahre nicht für möglich gehaltenen Aufschwung. Anlagenanzahl und installierte Leistung haben in diesem Zeitraum mit durchschnittlichen jährlichen Wachstumsraten von mehr als 30 Prozent zugenommen, die mittlere installierte Leistung pro neu errichteter Anlage stieg dabei um das Zehnfache und die technische Verfügbarkeit der Anlagen liegt mittlerweile bei über 98 Prozent. Mit größer werdenden Anlagen zeigt sich weiterhin ein klarer Trend zu Blattwinkel verstellbaren Konzepten, mit zunehmend drehzahlvariabler Betriebsweise. Vor dem von Vielen für die kommenden drei bis sechs Jahre prognostizierten Einstieg in die großtechnische Offshore- Windenergienutzung mit den damit verbundenen immensen technologischen und strukturellen Herausforderungen erscheint es sinnvoll, einen kritischen Blick zurückzuwerfen auf die 90er Jahre mit den ihnen zugrunde liegenden förderpolitischen Rahmenbedingungen. Dabei soll die Frage beantwortet werden, welchen konkreten Einfluss die staatlichen Forschungs- und Förderprogramme, besonders das "250 MW Wind"-Programm, auf die Entwicklung der Windenergienutzung hatten, das heißt, unter welchen Bedingungen sich bestimmte Techniklinien durchsetzten, wie der Einfluss eines geschützten Marktes durch gesetzlich garantierte Einspeisetarife auf diese Entwicklung zu bewerten ist und schließlich, welche Fehlentwicklungen möglicher Weise eingetreten sind. Dazu wird mit Hilfe von Lernkurven gezeigt, welche Kostenreduktionen insgesamt erzielt wurden, wie hoch die dazu notwendigen staatlichen Finanzmittel waren und welche Schlussfolgerungen daraus für die Zukunft abgeleitet werden können. Die Arbeit soll insgesamt dazu beitragen, die erreichten technischen Entwicklungsschritte vor dem Hintergrund der förderpolitischen Gegebenheiten besser zu verstehen, Chancen für gezielte Änderungen in der Förderpraxis zu ergreifen und Hinweise auf die Ausgestaltung von zukünftigen Forschungsprogrammen und Entwicklungsschwerpunkten im Bereich der Windenergie zu geben, um weitere Kostensenkungspotenziale auszuschöpfen. Dabei wird sich die zukünftige Schwerpunktsetzung in der programmatischen Ausrichtung der Forschung stärker auf die drei wichtigsten Anwendungsfelder für Windenergieanlagen konzentrieren müssen, die großtechnische Offshore- Anwendung, die netzgebundene, dezentrale Energieversorgung sowie auf Windenergieanlagen zur ländlichen Elektrifizierung in autonomen Versorgungssystemen für Schwellen- und Entwicklungsländer.

Photovoltaic hybrid systems for rural electrification in the Mekong countries

In rural areas of the Mekong Countries, the problem of electricity supplying rural communities is particularly alarming. Supplying power to these areas requires facilities that are not economically viable. However, government programs are under way to provide this product that is vital to community well being. A nation priority of Mekong Countries is to provide electrical power to people in rural areas, within normal budgetary constraints. Electricity must be introduced into rural areas in such a way that maximize the technical, economic and social benefit. Another consideration is the source of electrical generation and the effects on the natural environment. The main research purpose is to implement field tests, monitoring and evaluation of the PV-Diesel Hybrid System (PVHS) at the Energy Park of School of Renewable Energy Technology (SERT) in order to test the PVSH working under the meteorological conditions of the Mekong Countries and to develop a software simulation called RES, which studies the technical and economic performance of rural electrification options. This software must be easy to use and understand for the energy planner on rural electrification projects, to evaluate the technical and economic performance of the PVHS based on the renewable energy potential for rural electrification of the Mekong Country by using RES. Finally, this project aims to give guidance for the possible use of PVHS application in this region, particularly in regard to its technical and economic sustainability. PVHS should be promoted according to the principles of proper design and adequate follow up with maintenance, so that the number of satisfied users will be achieved. PVHS is not the only possible technology for rural electrification, but for the Mekong Countries it is one of the most proper choices. Other renewable energy options such as wind, biomass and hydro power need to be studied in future.

Erneuerbare Energien im Verbund mit Hochleistungs-Bleiakkumulatoren zur Bereitstellung von Spitzenleistung - am Beispiel von Windkraftwerken im 20 kV-Versorgungsnetz der CEGEDEL / Luxemburg -

Die wachsende Weltbevölkerung bedingt einen höheren Energiebedarf, dies jedoch unter der Beachtung der nachhaltigen Entwicklung. Die derzeitige zentrale Versorgung mit elektrischer Energie wird durch wenige Erzeugungsanlagen auf der Basis von fossilen Primärenergieträgern und Kernenergie bestimmt, die die räumlich verteilten Verbraucher zuverlässig und wirtschaftlich über ein strukturiertes Versorgungssystem beliefert. In den Elektrizitätsversorgungsnetzen sind keine nennenswerten Speicherkapazitäten vorhanden, deshalb muss die von den Verbrauchern angeforderte Energie resp. Leistung jederzeit von den Kraftwerken gedeckt werden. Bedingt durch die Liberalisierung der Energiemärkte und die geforderte Verringerung der Energieabhängigkeit Luxemburgs, unterliegt die Versorgung einem Wandel hin zu mehr Energieeffizienz und erhöhter Nutzung der dargebotsabhängigen Energiequellen. Die Speicherung der aus der Windkraft erzeugten elektrischen Energie, wird in den Hochleistungs-Bleiakkumulatoren, errichtet im ländlichen Raum in der Nähe der Windkraftwerke, eingespeichert. Die zeitversetzte Einspeisung dieser gespeicherten elektrischen Energie in Form von veredelter elektrischer Leistung während den Lastspitzen in das 20 kV-Versorgungsnetz der CEGEDEL stellt die Innovation in der luxemburgischen Elektrizitätsversorgung dar. Die Betrachtungen beschränken sich somit auf die regionale, relativ kleinräumige Einbindung der Windkraft in die elektrische Energieversorgung des Großherzogtums Luxemburg. Die Integration der Windkraft im Regionalbereich wird in den Vordergrund der Untersuchung gerückt. Überregionale Ausgleichseffekte durch Hochspannungsleitungen der 230/400 kV-Systeme werden außer Acht gelassen. Durch die verbrauchernahe Bereitstellung von elektrischer Spitzenleistung vermindern sich ebenfalls die Übertragungskosten aus den entfernten Spitzenlastkraftwerken, der Ausbau von Kraftwerkskapazitäten kann in die Zukunft verschoben werden. Die Emission von Treibhausgasen in thermischen Kraftwerken wird zum Teil reduziert. Die Berechnungen der Wirtschaftlichkeit von Hybridanlagen, zusammengesetzt aus den Windkraftwerken und den Hochleistungs-Bleiakkumulatoren bringen weitere Informationen zum Einsatz dieser dezentralen Speichern, als Partner der nachhaltigen Energieversorgung im ländlichen Raum. Die untersuchte Einspeisung von erneuerbarer Spitzenleistung lässt sich auch in die Entwicklungsländer übertragen, welche nicht über zentrale Kraftwerkskapazitäten und Verteilungsnetze verfügen.

Seismic behavior of capacity designed masonry walls in low seismicity regions

Eurocode 8 representing a new generation of structural design codes in Europe defines ‎requirements for the design of buildings against earthquake action. In Central and ‎Western Europe, the newly defined earthquake zones and corresponding design ground ‎acceleration values, will lead in many cases to earthquake actions which are remarkably ‎higher than those defined so far by the design codes used until now in Central Europe. ‎ In many cases, the weak points of masonry structures during an earthquake are the corner ‎regions of the walls. Loading of masonry walls by earthquake action leads in most cases ‎to high shear forces. The corresponding bending moment in such a wall typically causes a ‎significant increase of the eccentricity of the normal force in the critical wall cross ‎section. This in turn leads ultimately to a reduction of the size of the compression zone in ‎unreinforced walls and a high concentration of normal stresses and shear stresses in the ‎corner regions. ‎ Corner-Gap-Elements, consisting of a bearing beam located underneath the wall and ‎made of a sufficiently strong material (such as reinforced concrete), reduce the effect of ‎the eccentricity of the normal force and thus restricts the pinching effect of the ‎compression zone. In fact, the deformation can be concentrated in the joint below the ‎bearing beam. According to the principles of the Capacity Design philosophy, the ‎masonry itself is protected from high stresses as a potential cause of brittle failure. ‎ Shaking table tests at the NTU Athens Earthquake Engineering Laboratory have proven ‎the effectiveness of the Corner-Gap-Element. The following presentation will cover the ‎evaluation of various experimental results as well as a numerical modeling of the ‎observed phenomena.‎

The Corticiaceae (Basidiomycetes) in Taiwan

Geographically, Taiwan is an Island and situated in the northeast of Asia, on the western side of the Pacific Basin, at the southeast of main China, south of Japan, and north of the Philippines. The main topographic character is the longitudinally oriented mountainous area. More than 200 peaks rise above 3000 m. They departed Taiwan into two lowland areas, an eastern and western plain. Taiwan is departed into subtropical (north area) and tropical zone (south area), which have a warm and humid climate, due to the Tropic of Cancer passing through. The average annual temperature in the lowland amounts to 28°C (7~38°C). The temperate climate also presents in the mountainous areas. The tropical typhoons usually come in summer and bring heavy rain, while the monsoon seasons have an important effect on the regional rainfall distribution. The mean annual rainfall of Taiwan is about 2600 mm (1000~6700 mm); the mountainous areas receive more rain than the lowlands. In Taiwan, according to different temperature and vegetation, the ecological environments were given rise to vertical biotic zonations, and form five major types: highland snowfield, highland meadow, coniferous forest, deciduous forest, and tropical forest. Six National Parks in Taiwan are located in the mountainous areas, in the north, the south, and on Jinmen Island. The National Parks represent about 8.4% of the country area. In this study, the collection sites are situated in Yangmingshan, Shei-Pa, Yushan, and Kenting National Park. Due to the island isolation, the proportions of endemic species are great in Taiwan, which also presents a high biodiversity. There are 4255 species of vascular plants including 1133 endemic. 5936 species in 1276 genera of fungi are hitherto reported in Taiwan. Among them, 233 Corticiaceae species were recorded, over one third (79 species) of them are known only from Taiwan. The first fungal report in Taiwan is about Phytophthora cyperi, published by the Japanese researcher T. Kawakami in 1904. Therefore, the history of research about fungi in Taiwan is more than one hundred years old. An eminent Japanese mycologist K. Sawada made an intensive survey from 1919 to 1959, and reported 2464 fungi species in his eleven volumes of “Descriptive Catalogue of Formosan Fungi”. However, only a few species (21 species in 9 genera) of Corticiaceae were recorded. From 1973, Chen and Lin resumed the study on Corticiaceae, and also some other foreign mycologists contributed for this field after 1980. The German research group lead by Franz Oberwinkler from Tübingen University collected in Taiwan several times. They published a number of new species and new records. Since 1989, S. H. Wu, a Taiwanese mycologist, has published a great amount of reports on corticioid fungi from Taiwan. Corticioid fungi were made up by the large and heterogeneous unnatural family Corticiaceae and other resupinate fungi belonging to other natural families in the Agaricomycetes. Molecular studies have shown that corticioid genera are distributed across all major clades of Agaricomycetes indicating that the corticioid fungi represent a polyphyletic group. They have resupinate fruitbodies and similar habitats. Species are characterized by simple fruitbody, more or less effused, and present smooth, porioid, grandinioid to odontioid hymenial surface. The fruitbodies are differently colored and usually soft to tough. Most of the Corticiaceae species are wood-saprobic organisms and gain the energy from the decomposing of wood-substrate such as cellulose or lignin. Materials for this study were collected by the author and other mycologists in Taiwan during surveys in April and May 1996, and March 2007, using the spring season with its high humidity and warm climate which are optimal conditions for the development of fungi. For assembling, the convenience sampling method was used in this study. This approach was chosen because it enables to detect a high biodiversity in a short time, and also to find species with rare or patchy distribution. The collecting sites from the North to the South include four National Parks and some preserved forests. They cover many different habitats such as low lands and high mountains. Fresh specimens were dried and analysed with a light microscope. 265 specimens belonging to Corticiaceae were studied in this research. Among them, 50 species in 21 genera including 11 new records and 10 new species were described with text and drawing. Four new species are belonging to Hyphodontia (H. sp. nov. 1, H. sp. nov. 2, H. sp. nov. 3, and H. sp. nov. 4), four to Schizopora (Sch. sp. nov. 1, Sch. sp. nov. 2, Sch. sp. nov. 3, and Sch. sp. nov. 4), one in Trechispora (T. sp. nov. 1), and one in Tubulicrinis (T. sp. nov. 1). Species recorded as new are Aleurodiscus amorphus, Botryohypochnus isabellinus, Hyphodontia cineracea, Hyphodontia palmae, Hypochnicium vellereum, Merulius tremellosus, Metulodontia nivea, Paullicorticium ansatum, Phlebia radiata, Phlebiella ardosiaca, and Xylobolus frustulatus. Besides, Botryohypochnus, Merulius, Metulodontia, Paullicorticium, and Xylobolus are also newly recorded genera in Taiwan. The genus Hyphodontia presents the highest diversity with 20 out of 50 species recorded. The second important genus is Hyphoderma, however with only 5 species. This indicates that Hyphodontia and Hyphoderma have a higher ability to develop in variable environments and approximately shows the predominance of these two genera in Taiwanese Corticiaceae. There are 11 new records out of the 50 species recorded, representing 22%. Some species, e.g. Hypochnicium vellereum and Paullicorticium ansatum were in the past recorded only in Europe and North America with cold and temperate climate. The samples of them are for the first time found in the subtropical belt, and display some difference from those of temperate regions. These collections should be molecularly investigated to clarify if they represent the same species of temperate areas. Patchily distributed species, for example Phlebiella ardosiaca, previously known only in Europe, and Hyphodontia palmae collected only in Brazil, were first recorded in different continents. Two possibilities are indicated by these new records: they are worldwide species but very rare to be found, or the Taiwanese specimens are taxonomically different. More survey from other continents and molecular study for these collections should be done in the future to solve this question. The distribution of Corticiaceae in Taiwan presents the variations in the north, central, and south areas and shows the diversity in lowlands and high mountains. The results of this study provide the evidence that the temperate Corticiaceae species displays a wider distribution. Subtropical and tropical taxa probably have also high dispersal capacities, and could possibly be found in the future in neighboring areas such as China, Japan, Korea or South Asia, but this needs further researches. In the total of 50 species, 10 new taxa were described in this study, giving about 20%. Some new species (e.g. Hyphodontia sp. 1, Hyphodontia sp. 2, and Hyphodontia sp. 3) are very similar to known species (Hyphodontia sambuci and Hyphodontia formosana), and the distinctive characters of Schizopora sp. nov. 1 are intermediate between those of Schizopora paradoxa and Hyphodontia flavipora. Thus, these small differences between the new and known species, suggest that the speciation occurred when the fungi migrated into Taiwan, due to the high diversity of environment, and amounts of the endemic plants. Taiwan is an intermediate place for the south (tropical) fungal species to migrate and adapt to north (temperate) regions. The middle and high altitude environments in Taiwan offer good conditions for the fungal speciation and possibly the occurrence of physiological changes to adapt to the temperate climate. Thus Taiwan has an important position for the biogeography of Asia mycobiota. 5936 known species in Taiwan represent about only 20% of the estimated number (24000) of Taiwanese fungal taxa. In this study, the findings (22% new records and 20% new species) indicate that amounts of unknown fungi species are expected in Taiwan. The lack of knowledge indicates that many new species are awaiting description, and fungal survey in Taiwan remains in a Pioneer phase. The last three wide surveys of Corticiaceae researches took place 20 years before this study (Chen & Lin 1977, Lin & Chen 1989, Wu 1990). After previous important contributions, the present taxonomic study comprising 21 genera is the most extensive on Corticiaceae of Taiwan.

Economic evaluation of proposed pure and mixed stands in Central Vietnam highlands

In comparison with mixed forest stands, the cultivation of pure plantations in Vietnam entails serious ecological consequences such as loss of biodiversity and higher rate of soil erosion. The economic evaluation is elaborated between pure plantations and mixed forests where the fast-growing tree species are mixed with slow growing tree species which are planted in stripes separating the segments with fast-growing tree species (Acacia sp.). For the evaluation, the input values were used from local costs of goods, services and labour. The results show that the internal rate of return is the highest in the case of pure plantation in comparison with mixed forests – 86% to 77%(first planting pattern: Acacia sp. + noble hardwood species) and 54% (second planting pattern: Acacia + Dipterocarpus sp. + Sindora sp.). The average profit per hectare and year is almost five times higher in the case of mixed stands. The first planting pattern reaches 2,650 $, the second planting pattern 2,280 $ and the pure acacia plantation only 460 $. From an economic point of view, the cultivation of mixed forests that corresponds to the principles of sustainable forestry generates a good economical profit while maintaining habitat complexity and biodiversity.

The Human in the Loop: User Participation in Self-Adaptive Software

Self-adaptive software provides a profound solution for adapting applications to changing contexts in dynamic and heterogeneous environments. Having emerged from Autonomic Computing, it incorporates fully autonomous decision making based on predefined structural and behavioural models. The most common approach for architectural runtime adaptation is the MAPE-K adaptation loop implementing an external adaptation manager without manual user control. However, it has turned out that adaptation behaviour lacks acceptance if it does not correspond to a user’s expectations – particularly for Ubiquitous Computing scenarios with user interaction. Adaptations can be irritating and distracting if they are not appropriate for a certain situation. In general, uncertainty during development and at run-time causes problems with users being outside the adaptation loop. In a literature study, we analyse publications about self-adaptive software research. The results show a discrepancy between the motivated application domains, the maturity of examples, and the quality of evaluations on the one hand and the provided solutions on the other hand. Only few publications analysed the impact of their work on the user, but many employ user-oriented examples for motivation and demonstration. To incorporate the user within the adaptation loop and to deal with uncertainty, our proposed solutions enable user participation for interactive selfadaptive software while at the same time maintaining the benefits of intelligent autonomous behaviour. We define three dimensions of user participation, namely temporal, behavioural, and structural user participation. This dissertation contributes solutions for user participation in the temporal and behavioural dimension. The temporal dimension addresses the moment of adaptation which is classically determined by the self-adaptive system. We provide mechanisms allowing users to influence or to define the moment of adaptation. With our solution, users can have full control over the moment of adaptation or the self-adaptive software considers the user’s situation more appropriately. The behavioural dimension addresses the actual adaptation logic and the resulting run-time behaviour. Application behaviour is established during development and does not necessarily match the run-time expectations. Our contributions are three distinct solutions which allow users to make changes to the application’s runtime behaviour: dynamic utility functions, fuzzy-based reasoning, and learning-based reasoning. The foundation of our work is a notification and feedback solution that improves intelligibility and controllability of self-adaptive applications by implementing a bi-directional communication between self-adaptive software and the user. The different mechanisms from the temporal and behavioural participation dimension require the notification and feedback solution to inform users on adaptation actions and to provide a mechanism to influence adaptations. Case studies show the feasibility of the developed solutions. Moreover, an extensive user study with 62 participants was conducted to evaluate the impact of notifications before and after adaptations. Although the study revealed that there is no preference for a particular notification design, participants clearly appreciated intelligibility and controllability over autonomous adaptations.

Electronic origin of bond softening and hardening in femtosecond-laser-excited magnesium

Many ultrafast structural phenomena in solids at high fluences are related to the hardening or softening of particular lattice vibrations at lower fluences. In this paper we relate femtosecond-laser-induced phonon frequency changes to changes in the electronic density of states, which need to be evaluated only in the electronic ground state, following phonon displacement patterns. We illustrate this relationship for a particular lattice vibration of magnesium, for which we—surprisingly—find that there is both softening and hardening as a function of the femtosecond-laser fluence. Using our theory, we explain these behaviours as arising from Van Hove singularities: We show that at low excitation densities Van Hove singularities near the Fermi level dominate the change of the phonon frequency while at higher excitations Van Hove singularities that are further away in energy also become important. We expect that our theory can as well shed light on the effects of laser excitation of other materials.