Dye-sensitized solar cells based on perylene derivatives

The oil price rises more and more, and the world energy consumption is projected to expand by 50 percent from 2005 to 2030. Nowadays intensive research is focused on the development of alternative energies. Among them, there are dye-sensitized nanocrystalline solar cells (DSSCs) “the third generation solar cells”. The latter have gained attention during the last decade and are currently subject of intense research in the framework of renewable energies as a low-cost photovoltaic. At present DSSCs with ruthenium based dyes exhibit highest efficiencies (ca 11%). The objective of the present work is to fabricate, characterize and improve the performance of DSSCs based on metal free dyes as sensitizers, especially on perylene derivatives. The work begins by a general introduction to the photovoltaics and dye-sensitized solar cells, such as the operating principles and the characteristics of the DSSCs. Chapter 2 and 3 discuss the state of the art of sensitizers used in DSSCs, present the compounds used as sensitizer in the present work and illustrate practical issues of experimental techniques and device preparation. A comparative study of electrolyte-DSSCs based on P1, P4, P7, P8, P9, and P10 are presented in chapter 4. Experimental results show that the dye structure plays a crucial role in the performance of the devices. The dye based on the spiro-concept (bipolar spiro compound) exhibited a higher efficiency than the non-spiro compounds. The presence of tert-butylpyridine as additive in the electrolyte was found to increase the open circuit voltage and simultaneously decrease the efficiency. The presence of lithium ions in the electrolyte increases both output current and the efficiency. The sensitivity of the dye to cations contained in the electrolyte was investigated in the chapter 5. FT-IR and UV-Vis were used to investigate the in-situ coordination of the cation to the adsorbed dye in the working devices. The open-circuit voltage was found to depend on the number of coordination sites in the dye. P1 with most coordination sites has shown the lowest potential drop, opposite to P7, which is less sensitive to cations in the working cells. A strategy to improve the dye adsorption onto the TiO2 surface, and thus the light harvesting efficiency of the photoanode by UV treatment, is presented in chapter 6. The treatment of the TiO2 film with UV light generates hydroxyl groups and renders the TiO2 surface more and more hydrophilic. The treated TiO2 surface reacts readily with the acid anhydride group of the dye that acts as an anchoring group and improves the dye adsorption. The short-circuit current density and the efficiency of the electrolyte-based dye cells was considerably improved by the UV treatment of the TiO2 film. Solid-state dye-sensitized solar cells (SSDs) based on spiro-MeOTAD (used as hole transport material) are studied in chapter 7. The efficiency of SSDs was globally found to be lower than that of electrolyte-based solar cells. That was due to poor pore filling of the dye-loaded TiO2 film by the spin-coated spiro-MeOTAD and to the significantly slower charge transport in the spiro-MeOTAD compared to the electrolyte redox mediator. However, the presence of the donor moieties in P1 that are structurally similar to spiro-MeOTAD was found to improve the wettability of the P1-loaded TiO2 film. As a consequence the performance of the P1-based solid-state cells is better compared to the cells based on non-spiro compounds.

Development and Integration of Biocontrol Products in Branched Broomrape (Phelipanche ramosa) management in Tomato

Parasitic weeds of the genera Striga, Orobanche, and Phelipanche pose a severe problem for agriculture because they are difficult to control and are highly destructive to several crops. The present work was carried out during the period October, 2009 to February, 2012 to evaluate the potential of arbuscular mycorrhizal fungi (AMF) to suppress P. ramosa on tomatoes and to investigate the effects of air-dried powder and aqueous extracts from Euphorbia hirta on germination and haustorium initiation in Phelipanche ramosa. The work was divided into three parts: a survey of the indigenous mycorrhizal flora in Sudan, second, laboratory and greenhouse experiments (conducted in Germany and Sudan) to construct a base for the third part, which was a field trial in Sudan. A survey was performed in 2009 in the White Nile state, Sudan to assess AMF spore densities and root colonization in nine fields planted with 13 different important agricultural crops. In addition, an attempt was made to study the relationship between soil physico-chemical properties and AMF spore density, colonization rate, species richness and other diversity indices. The mean percentage of AMF colonization was 34%, ranging from 19-50%. The spore densities (expressed as per 100 g dry soil) retrieved from the rhizosphere of different crops were relatively high, varying from 344 to 1222 with a mean of 798. There was no correlation between spore densities in soil and root colonization percentage. A total of 45 morphologically classifiable species representing ten genera of AMF were detected with no correlation between the number of species found in a soil sample and the spore density. The most abundant genus was Glomus (20 species). The AMF diversity expressed by the Shannon–Weaver index was highest in sorghum (H\= 2.27) and Jews mallow (H\= 2.13) and lowest in alfalfa (H\= 1.4). With respect to crop species, the genera Glomus and Entrophospora were encountered in almost all crops, except for Entrophospora in alfalfa. Kuklospora was found only in sugarcane and sorghum. The genus Ambispora was recovered only in mint and okra, while mint and onion were the only species on which no Acaulospora was found. The hierarchical cluster analysis based on the similarity among AMF communities with respect to crop species overall showed that species compositions were relatively similar with the highest dissimilarity of about 25% separating three of the mango samples and the four sorghum samples from all other samples. Laboratory experiments studied the influence of root and stem exudates of three tomato varieties infected by three different Glomus species on germination of P. ramosa. Root exudates were collected 21or 42 days after transplanting (DAT) and stem exudates 42 DAT and tested for their effects on germination of P. ramosa seeds in vitro. The tomato varieties studied did not have an effect on either mycorrhizal colonization or Phelipanche germination. Germination in response to exudates from 42 day old mycorrhizal plants was significantly reduced in comparison to non-mycorrhizal controls. Germination of P. ramosa in response to root exudates from 21 day old plants was consistently higher than for 42 day-old plants (F=121.6; P<.0001). Stem diffusates from non-mycorrhizal plants invariably elicited higher germination than diffusates from the corresponding mycorrhizal ones and differences were mostly statistically significant. A series of laboratory experiments was undertaken to investigate the effects of aqueous extracts from Euphorbia hirta on germination, radicle elongation, and haustorium initiation in P. ramosa. P. ramosa seeds conditioned in water and subsequently treated with diluted E. hirta extract (10-25% v/v) displayed considerable germination (47-62%). Increasing extract concentration to 50% or more reduced germination in response to the synthetic germination stimulants GR24 and Nijmegen-1 in a concentration dependent manner. P. ramosa germlings treated with diluted Euphorbia extract (10-75 % v/v) displayed haustorium initiation comparable to 2, 5-Dimethoxy-p-benzoquinon (DMBQ) at 20 µM. Euphorbia extract applied during conditioning reduced haustorium initiation in a concentration dependent manner. E. hirta extract or air-dried powder, applied to soil, induced considerable P. ramosa germination. Pot experiments were undertaken in a glasshouse at the University of Kassel, Germany, to investigate the effects of P. ramosa seed bank on tomato growth parameters. Different Phelipanche seed banks were established by mixing the parasite seeds (0 - 32 mg) with the potting medium in each pot. P. ramosa reduced all tomato growth parameters measured and the reduction progressively increased with seed bank. Root and total dry matter accumulation per tomato plant were most affected. P. ramosa emergence, number of tubercles, and tubercle dry weight increased with the seed bank and were, invariably, maximal with the highest seed bank. Another objective was to determine if different AM fungi differ in their effects on the colonization of tomatoes with P. ramosa and the performance of P. ramosa after colonization. Three AMF species viz. GIomus intraradices, Glomus mosseae and Glomus Sprint® were used in this study. For the infection, P. ramosa seeds (8 mg) were mixed with the top 5 cm soil in each pot. No mycorrhizal colonization was detected in un-inoculated control plants. P. ramosa infested, mycorrhiza inoculated tomato plants had significantly lower AMF colonization compared to plants not infested with P. ramosa. Inoculation with G. intraradices, G. mosseae and Glomus Sprint® reduced the number of emerged P. ramosa plants by 29.3, 45.3 and 62.7% and the number of tubercles by 22.2, 42 and 56.8%, respectively. Mycorrhizal root colonization was positively correlated with number of branches and total dry matter of tomatoes. Field experiments on tomato undertaken in 2010/12 were only partially successful because of insect infestations which resulted in the complete destruction of the second run of the experiment. The effects of the inoculation with AMF, the addition of 10 t ha-1 filter mud (FM), an organic residues from sugar processing and 36 or 72 kg N ha-1 on the infestation of tomatoes with P. ramosa were assessed. In un-inoculated control plants, AMF colonization ranged between 13.4 to 22.1% with no significant differences among FM and N treatments. Adding AMF or FM resulted in a significant increase of branching in the tomato plants with no additive effects. Dry weights were slightly increased through FM application when no N was applied and significantly at 36 kg N ha-1. There was no effect of FM on the time until the first Phelipanche emerged while AMF and N application interacted. Especially AMF inoculation resulted in a tendency to delayed P. ramosa emergence. The marketable yield was extremely low due to the strong fruit infestation with insects mainly whitefly Bemisia tabaci and tomato leaf miner (Tuta absoluta). Tomatoes inoculated with varied mycorrhiza species displayed different response to the insect infestation, as G. intraradices significantly reduced the infestation, while G. mosseae elicited higher insect infestation. The results of the present thesis indicate that there may be a potential of developing management strategies for P. ramosa targeting the pre-attachment stage namely germination and haustorial initiation using plant extracts. However, ways of practical use need to be developed. If such treatments can be combined with AMF inoculation also needs to be investigated. Overall, it will require a systematic approach to develop management tools that are easily applicable and affordable to Sudanese farmers. It is well-known that proper agronomical practices such as the design of an optimum crop rotation in cropping systems, reduced tillage, promotion of cover crops, the introduction of multi-microbial inoculants, and maintenance of proper phosphorus levels are advantageous if the mycorrhiza protection method is exploited against Phelipanche ramosa infestation. Without the knowledge about the biology of the parasitic weeds by the farmers and basic preventive measures such as hygiene and seed quality control no control strategy will be successful, however.

Zum Querkrafttragverhalten von UHPC-Balken mit kombinierter Bewehrung aus Stahlfasern und Stabstahl

Ultrahochfester Beton besitzt aufgrund seiner Zusammensetzung eine sehr hohe Druckfestigkeit von 150 bis über 200 N/mm² und eine außergewöhnlich hohe Dichtigkeit. Damit werden Anwendungen in stark belasteten Bereichen und mit hohen Anforderungen an die Dauerhaftigkeit des Materials ermöglicht. Gleichzeitig zeigt ultrahochfester Beton bei Erreichen seiner Festigkeit ein sehr sprödes Verhalten. Zur Verhinderung eines explosionsartigen Versagens werden einer UHPC-Mischung Fasern zugegeben oder wird eine Umschnürung mit Stahlrohren ausgebildet. Die Zugabe von Fasern zur Betonmatrix beeinflusst neben der Verformungsfähigkeit auch die Tragfähigkeit des UHPC. Das Versagen der Fasern ist abhängig von Fasergeometrie, Fasergehalt, Verbundverhalten sowie Zugfestigkeit der Faser und gekennzeichnet durch Faserauszug oder Faserreißen. Zur Sicherstellung der Tragfähigkeit kann daher auf konventionelle Bewehrung außer bei sehr dünnen Bauteilen nicht verzichtet werden. Im Rahmen des Schwerpunktprogramms SPP 1182 der Deutschen Forschungsgemeinschaft (DFG) wurden in dem dieser Arbeit zugrunde liegenden Forschungsprojekt die Fragen nach der Beschreibung des Querkrafttragverhaltens von UHPC-Bauteilen mit kombinierter Querkraftbewehrung und der Übertragbarkeit bestehender Querkraftmodelle auf UHPC untersucht. Neben einer umfassenden Darstellung vorhandener Querkraftmodelle für Stahlbetonbauteile ohne Querkraftbewehrung und mit verschiedenen Querkraftbewehrungsarten bilden experimentelle Untersuchungen zum Querkrafttragverhalten an UHPC-Balken mit verschiedener Querkraftbewehrung den Ausgangspunkt der vorliegenden Arbeit. Die experimentellen Untersuchungen beinhalteten zehn Querkraftversuche an UHPC-Balken. Diese Balken waren in Abmessungen und Biegezugbewehrung identisch. Sie unterschieden sich nur in der Art der Querkraftbewehrung. Die Querkraftbewehrungsarten umfassten eine Querkraftbewehrung aus Stahlfasern oder Vertikalstäben, eine kombinierte Querkraftbewehrung aus Stahlfasern und Vertikalstäben und einen Balken ohne Querkraftbewehrung. Obwohl für die in diesem Projekt untersuchten Balken Fasergehalte gewählt wurden, die zu einem entfestigenden Nachrissverhalten des Faserbetons führten, zeigten die Balkenversuche, dass die Zugabe von Stahlfasern die Querkrafttragfähigkeit steigerte. Durch die gewählte Querkraftbewehrungskonfiguration bei ansonsten identischen Balken konnte außerdem eine quantitative Abschätzung der einzelnen Traganteile aus den Versuchen abgeleitet werden. Der profilierte Querschnitt ließ einen großen Einfluss auf das Querkrafttragverhalten im Nachbruchbereich erkennen. Ein relativ stabiles Lastniveau nach Erreichen der Höchstlast konnte einer Vierendeelwirkung zugeordnet werden. Auf Basis dieser Versuchsergebnisse und analytischer Überlegungen zu vorhandenen Querkraftmodellen wurde ein additiver Modellansatz zur Beschreibung des Querkrafttragverhaltens von UHPCBalken mit einer kombinierten Querkraftbewehrung aus Stahlfasern und Vertikalstäben formuliert. Für die Formulierung der Traganteile des Betonquerschnitts und der konventionellen Querkraftbewehrung wurden bekannte Ansätze verwendet. Für die Ermittlung des Fasertraganteils wurde die Faserwirksamkeit zugrunde gelegt. Das Lastniveau im Nachbruchbereich aus Viendeelwirkung ergibt sich aus geometrischen Überlegungen.

Heat stress response for physiological traits in dairy and dual purpose cattle populations on phenotypic and genetic scales

The main objective of this thesis was to determine the potential impact of heat stress (HS) on physiological traits of lactating cows and semen quality of bulls kept in a temperate climate. The thesis is comprised of three studies. An innovative statistical modeling aspect common to all three studies was the application of random regression methodology (RRM) to study the phenotypic and genetic trajectory of traits in dependency of a continuous temperature humidity index (THI). In the first study, semen quality and quantity traits of 562 Holstein sires kept on an AI station in northwestern Germany were analyzed in the course of THI calculated from data obtained from the nearest weather station. Heat stress was identified based on a decline in semen quality and quantity parameters. The identified general HS threshold (THI = 60) and the thermoneutal zone (THI in the range from 50 to 60) for semen production were lower than detected in studies conducted in tropical and subtropical climates. Even though adult bulls were characterized by higher semen productivity compared to younger bulls, they responded with a stronger semen production loss during harsh environments. Heritabilities (low to moderate range) and additive genetic variances of semen characteristics varied with different levels of THI. Also, based on genetic correlations genotype, by environment interactions were detected. Taken together, these findings suggest the application of specific selection strategies for specific climate conditions. In the second study, the effect of the continuous environmental descriptor THI as measured inside the barns on rectal temperatures (RT), skin temperatures (ST), vaginal temperatures (VT), respiration rates (RR), and pulse rate (PR) of lactating Holstein Friesian (HF) and dual-purpose German black pied cattle (DSN) was analyzed. Increasing HS from THI 65 (threshold) to THI 86 (maximal THI) resulted in an increase of RT by 0.6 °C (DSN) and 1 °C (HF), ST by 3.5 °C (HF) and 8 °C (DSN), VT by 0.3 °C (DSN), and RR by 47 breaths / minute (DSN), and decreased PR by 7 beats / minute (DSN). The undesired effects of rising THI on physiological traits were most pronounced for cows with high levels of milk yield and milk constituents, cows in early days in milk and later parities, and during summer seasons in the year 2014. In the third study of this dissertation, the genetic components of the cow’s physiological responses to HS were investigated. Heat stress was deduced from indoor THI measurements, and physiological traits were recorded on native DSN cows and their genetically upgraded crosses with Holstein Friesian sires in two experimental herds from pasture-based production systems reflecting a harsh environment of the northern part of Germany. Although heritabilities were in a low range (from 0.018 to 0.072), alterations of heritabilities, repeatabilities, and genetic components in the course of THI justify the implementation of genetic evaluations including heat stress components. However, low repeatabilities indicate the necessity of using repeated records for measuring physiological traits in German cattle. Moderate EBV correlations between different trait combinations indicate the potential of selection for one trait to simultaneously improve the other physiological attributes. In conclusion, bulls of AI centers and lactating cows suffer from HS during more extreme weather conditions also in the temperate climate of Northern Germany. Monitoring physiological traits during warm and humid conditions could provide precious information for detection of appropriate times for implementation of cooling systems and changes in feeding and management strategies. Subsequently, the inclusion of these physiological traits with THI specific breeding values into overall breeding goals could contribute to improving cattle adaptability by selecting the optimal animal for extreme hot and humid conditions. Furthermore, the recording of meteorological data in close distance to the cow and visualizing the surface body temperature by infrared thermography techniques might be helpful for recognizing heat tolerance and adaptability in cattle.