Effect of Feeding Rate on Plastic Extrudates

Selected grades of low density polyethylene (LDPE) polystyrene (PS) were extruded in a laboratory extruder by varying the feeding rate at different revolutions per minute and temperatures. The mechanical properties of the extruded plastic sheets were determined. LDPE shows a marked variation in mechanical properties with feeding rate while PS shows a marginal change in mechanical properties with feeding rate. However, for both plastics there is a particular feeding rate in the starved region which results in maximum mechanical properties.

Significance of Feeding Rate in the Extrusion of Filled and Gum 11R Vulcanizates

Filled and gum compounds of Isobutylene-Isoprene rubber were extruded through a laboratory extruder at various feeding rates, different temperatures and revolutions per minute. The extruded compounds were vulcanized up to their optimum cure times and the mechanical properties of the vulcanizates were determined. The properties suggest that there is a particular feeding rate in the starved fed region, which results in maximum mechanical properties. The study shows that running the extruder at a slightly starved condition is an attractive means of improving the physical properties.

Starved Feeding for Improving the Mechanical Properties of Styrene-Butadiene Rubber Vulcanizates

Gum and filled compounds of styrene-butadiene rubber are extruded through a laboratory extruder by varying the feeding rase at different temperatures and screw speed (rpm). The extruded compounds are vulcanized up4o their optimum cure times and the mechanical properties of the vulcanizates are determined. From the properties data obtained it Is concluded that there is a specific feeding rate wit in the starved fed region, which results In maximum Improved mechanical properties . The enhancement In properties is found to be due to better thermal and shear homogeneity.

Investigations on the biology of Indian Mackerel Rastrelliger kanagurta (Cuvier) along the Central Kerala coast with special reference to maturation, feeding and lipid dynamics

Dept. of Marine Biology, Microbiology & Biochemistry, Cochin University of Science and Technology

Studies on food and feeding of marine demersal finfishes with special reference to trophic interactions

Food and feeding habits of fourteen demersal finfishes exploited off the Karnataka coast were studied to investigate trophic interactions within the marine food web. Index of Relative Importance (lRI),Ontogenetic, seasonal (pre-monsoon, monsoon and post-monsoon) variation in feeding and prey-predator relationship studies were conducted.The results of prey-predator trophic interaction studies identified four major trophic guilds based on the predators feeding similarity.Trophic guild I is 'copepod and detritus fceders'with an average group similarity of 61.4%. The second trophic guild, 'prawn and crab feeders'with an average similarity of 52.7%. 'Acetes feeders', the largest trophic guild with an average group similarity of 62.5%, composed of six demersal finfish species.The guild 'piscivores' is constituted by C. limba/us and P. arsius with an average similarity of 45%.For each predator, ontogenetic diet shift is common and is characterized by prey of low to high trophic level.Strong selection of certain prey types was observed in some predators while most of them avoided abundant prey.In addition to Acetes spp, strong predation impact was observed for penaeid prawns, epibenthic crabs and detritus.This information on trophic guilds and prey-predator interactions can be used to construct trophic model on the benthic ecosystem off Karnataka and to investigate fishery induced changes as well as predation impact of different animals on commercially important demersals

Effect of Feeding Rate in Polymer Extrusion ”

Starve feeding of single screw extruder was described as an important means of improving the performance characteristics of the extruder. In addition to such improvement with versatility, the starve feeding technique also may affect the mechanical properties of the extrudate since the heat transfer an(l mixing characteristics in the starve fed and Hood fed extruders are not the same. Since the material is more loosely packed in the channels of the starve fed extruder, there may be greater bed mobility and uniformity. Further, the. thermal an(l shear induced degradation are also less since possibilities of developing local high temperatures are less compared to a densely compacted extruder bed. This study has been undertaken mainly to explore the effect of feeding rate on the mechanical properties of rubber and plastic extrudates since the effect of feeding rate has not been analysed from this angle so far.

Habitat ecology and food and feeding of the herring bow crab Varuna litterata (Fabricius, 1798) of Cochin backwaters, Kerala, India

Habitat ecology and food and feeding of the herring bow crab, Varuna litterata of Cochin Backwaters, Kerala, India were investigated for a period of one year (April 2011-March 2012). Among the 15 stations surveyed, the crabs were found to occur only in 4 stations, which had a close proximity to the sea. Sediment analysis of the stations revealed that the substratum of these stations is sandy in nature and is rich in organic carbon content (0.79% to 1.07%). These estuarine crabs is euryhaline and are found to be distributed in areas with a sandy substratum, higher organic carbon content and more tidal influx. The stomach contents analysis of crabs examined showed that their diet included crustacean remains, plants, sand and debris, fishes, miscellaneous group and unidentified matter. In adults and sub-adults, crustaceans formed the dominant food group, while in juveniles, sand and debris formed the dominant group. From the present study, V. litterata was found to be a predatory omnivore capable of ingesting both animal and plant tissues