Enhanced /3-adrenergic receptors in the brain and pancreas during pancreatic regeneration in weanling rats

Adrenergic stimulation has an inyortant role in the pancreatic It-cell proliferation and insulin secretion. In the present study. we have investigaled how sympathetic system mgulales the panrrealic n I rnerui nr ht an:ilyiing I'pinephi inn 1111 ), Norepinephrinc (NE) and /1-adrenergic receptor changes in the brain as (%eli is in the I swirls. Fill and NII showed a significant decrease in the brain regions, pancreas and plasma :rt 72Ius iller partial prurcrealectonty. We observed an increase in the circulating insulin levels at 72 hrs. Scatchard analysis using I CHI propranolol showed a significant increase in the number of loth the low affinity and high affinity t-adrenergic receplors in cerebral cortex and hypothalamus of partially pancreatectornised rats during peak DNA synthesis. The affinity of the receptors decrea,ed significantly in the low and high affinity receptors of cerebral cortex and the high affinity hypothalamic receptors. In file brain stein, low affinity receptors were increased significantly during regeneration whereas there was no change in the high affinity receptors. The pancreatic ff-adrenergic receptors were also up regulated at 72 firs after partial panerealectony. In vitro studies showed that /i-adrenergic receptors are positive regulators of islet cell proliferation and insulin secretion. Thus our results suggest that the t-adrenergic receptors are functionally enhanced during pancreatic regeneration, which in turn increases pancreatic ft-cell proliferation an(hilisulin secretion in wean hug rats.

Comparison of Electromagnetic Band Gap and Split-Ring Resonator Microstrip Lines as Stop Band Structures

In this paper, microstrip lines magnetically coupled to splitring resonators (SRRs) are conquved to electromagnetic bundgup (EBG) nr,rrostrip lines in terns q/ their stop-heard penjbrnmrnce and dimensions. In bath types o/ trunsmis•siou lines, signal propagation is inhibited in it certain jequency bwuL For EBG microstrip lines, the central frequency of such a forbidden band is determined by the period of the structure, whereas in SRR-hased microstrip lines the position of the frequency gap depends on the quasi-static resonant frequency of the rings. The main relevant conrributiun of this paper is to provide a tuning procedure to control the gap width in SRR microstrip lines, and to show that by using SRRs, device dimensions ale much smaller than those required by EBGs in order to obtain similar stop-banal performance. This has been demonstrated by fill-wave electromagnetic simulations and experimentally verified from the characterization ql two fabricated microstrip lines: one with rectangular SRRs etched on the upper substrate side, and the other with a periodic perturbation cf'strip width. For similar rejection and 1-(;H,. gap width centered at 4.5 Gllz, it has been found that the SRR microstrip line is•,fve times shorter. In addition, no ripple is appreciable in the allowed band for the .SRR-hared structure, whereas due to dispersion, certain mismatch is expected in the EBG prototype. Due to the high-frequency selectivity, controllable gap width, and small dimensions, it is believed that SRR coupled to planar transmission lines can have an actual impact on the design of stop-band filters compatible with planar technology, and can be an alternative to present solutions based on distributed approaches or EBG

Recyclable Short Fibre Reinforced Plastics PP/Nylon and HDPE/Nylon composites

The study shows that standard plastics like polypropylene and high density polyethylene can be reinforced by adding nylon short fibres. Compared to the conventional glass reinforced thermoplastics this novel class of reinforced thermoplastics has the major advantage of recyclability. Hence such composites represent a new spectrum of recyclable polymer composites. The fibre length and fibre diameter used for reinforcement are critical parameters While there is a critical fibre length below which no effective reinforcement takes place, the reinforcement improves when the fibre diameter decreases due to increased surface area.While the fibres alone give moderate reinforcement, chemical modification of the matrix can further improve the strength and modulus of the composites. Maleic anhydride grafting in presence of styrene was found to be the most efficient chemical modification. While the fibre addition enhances the viscosity of the melt at lower shear rates, the enhancement at higher shear rate is only marginal. This shows that processing of the composite can be done in a similar way to that of the matrix polymer in high shear operations such as injection moulding. Another significant observation is the decrease in melt viscosity of the composite upon grafting. Thus chemical modification of matrix makes processing of the composite easier in addition to improving the mechanical load bearing capacity.For the development of a useful short fibre composite, selection of proper materials, optimum design with regard to the particular product and choosing proper processing parameters are most essential. Since there is a co-influence of many parameters, analytical solutions are difficult. Hence for selecting proper processing parameters 'rnold flow' software was utilized. The orientation of the fibres, mechanical properties, temperature profile, shrinkage, fill time etc. were determined using the software.Another interesting feature of the nylon fibre/PP and nylon fibre/HDPE composites is their thermal behaviour. Both nylon and PP degrade at the same temperature in single steps and hence the thermal degradation behaviour of the composites is also being predictable. It is observed that the thermal behaviour of the matrix or reinforcement does not affect each other. Almost similar behaviour is observed in the case of nylon fibre/HDPE composites. Another equally significant factor is the nucleating effect of nylon fibre when the composite melt cools down. In the presence of the fibre the onset of crystallization occurs at slightly higher temperature.When the matrix is modified by grafting, the onset of crystallization occurs at still higher temperature. Hence it may be calculated that one reason for the improvement in mechanical behaviour of the composite is the difference in crystallization behaviour of the matrix in presence of the fibre.As mentioned earlier, a major advantage of these composites is their recyclability. Two basic approaches may be employed for recycling namely, low temperature recycling and high temperature recycling. In the low temperature recycling, the recycling is done at a temperature above the melting point of the matrix, but below that of the fibres while in the high temperature route. the recycling is done at a temperature above the melting points of both matrix and fibre. The former is particularly interesting in that the recycled material has equal or even better mechanical properties compared to the initial product. This is possible because the orientation of the fibre can improve with successive recycling. Hence such recycled composites can be used for the same applications for which the original composite was developed. In high temperature recycling, the composite is converted into a blend and hence the properties will be inferior to that of the original composite, but will be higher than that of the matrix material alone.

Mathematical Modelling of the Dynamics of Granular Materials in a Rotating Cylinder

The current study is aimed at the development of a theoretical simulation tool based on Discrete Element Method (DEM) to 'interpret granular dynamics of solid bed in the cross section of the horizontal rotating cylinder at the microscopic level and subsequently apply this model to establish the transition behaviour, mixing and segregation.The simulation of the granular motion developed in this work is based on solving Newton's equation of motion for each particle in the granular bed subjected to the collisional forces, external forces and boundary forces. At every instant of time, the forces are tracked and the positions velocities and accelarations of each partcle is The software code for this simulation is written in VISUAL FORTRAN 90 After checking the validity of the code with special tests, it is used to investigate the transition behaviour of granular solids motion in the cross section of a rotating cylinder for various rotational speeds and fill fraction.This work is hence directed towards a theoretical investigation based on Discrete Element Method (DEM) of the motion of granular solids in the radial direction of the horizontal cylinder to elucidate the relationship between the operating parameters of the rotating cylinder geometry and physical properties ofthe granular solid.The operating parameters of the rotating cylinder include the various rotational velocities of the cylinder and volumetric fill. The physical properties of the granular solids include particle sizes, densities, stiffness coefficients, and coefficient of friction Further the work highlights the fundamental basis for the important phenomena of the system namely; (i) the different modes of solids motion observed in a transverse crosssection of the rotating cylinder for various rotational speeds, (ii) the radial mixing of the granular solid in terms of active layer depth (iii) rate coefficient of mixing as well as the transition behaviour in terms of the bed turnover time and rotational speed and (iv) the segregation mechanisms resulting from differences in the size and density of particles.The transition behaviour involving its six different modes of motion of the granular solid bed is quantified in terms of Froude number and the results obtained are validated with experimental and theoretical results reported in the literature The transition from slumping to rolling mode is quantified using the bed turnover time and a linear relationship is established between the bed turn over time and the inverse of the rotational speed of the cylinder as predicted by Davidson et al. [2000]. The effect of the rotational speed, fill fraction and coefficient of friction on the dynamic angle of repose are presented and discussed. The variation of active layer depth with respect to fill fraction and rotational speed have been investigated. The results obtained through simulation are compared with the experimental results reported by Van Puyvelde et. at. [2000] and Ding et at. [2002].The theoretical model has been further extended, to study the rmxmg and segregation in the transverse direction for different particle sizes and their size ratios. The effect of fill fraction and rotational speed on the transverse mixing behaviour is presented in the form of a mixing index and mixing kinetics curve. The segregation pattern obtained by the simulation of the granular solid bed with respect to the rotational speed of the cylinder is presented both in graphical and numerical forms. The segregation behaviour of the granular solid bed with respect to particle size, density and volume fraction of particle size has been investigated. Several important macro parameters characterising segregation such as mixing index, percolation index and segregation index have been derived from the simulation tool based on first principles developed in this work.

Development of Time - Frequency Techniques for Sonar Applications

Sonar signal processing comprises of a large number of signal processing algorithms for implementing functions such as Target Detection, Localisation, Classification, Tracking and Parameter estimation. Current implementations of these functions rely on conventional techniques largely based on Fourier Techniques, primarily meant for stationary signals. Interestingly enough, the signals received by the sonar sensors are often non-stationary and hence processing methods capable of handling the non-stationarity will definitely fare better than Fourier transform based methods.Time-frequency methods(TFMs) are known as one of the best DSP tools for nonstationary signal processing, with which one can analyze signals in time and frequency domains simultaneously. But, other than STFT, TFMs have been largely limited to academic research because of the complexity of the algorithms and the limitations of computing power. With the availability of fast processors, many applications of TFMs have been reported in the fields of speech and image processing and biomedical applications, but not many in sonar processing. A structured effort, to fill these lacunae by exploring the potential of TFMs in sonar applications, is the net outcome of this thesis. To this end, four TFMs have been explored in detail viz. Wavelet Transform, Fractional Fourier Transfonn, Wigner Ville Distribution and Ambiguity Function and their potential in implementing five major sonar functions has been demonstrated with very promising results. What has been conclusively brought out in this thesis, is that there is no "one best TFM" for all applications, but there is "one best TFM" for each application. Accordingly, the TFM has to be adapted and tailored in many ways in order to develop specific algorithms for each of the applications.

Performance of Gabion Faced Reinforced Earth Retaining Walls

Gabion faced re.taining walls are essentially semi rigid structures that can generally accommodate large lateral and vertical movements without excessive structural distress. Because of this inherent feature, they offer technical and economical advantage over the conventional concrete gravity retaining walls. Although they can be constructed either as gravity type or reinforced soil type, this work mainly deals with gabion faced reinforced earth walls as they are more suitable to larger heights. The main focus of the present investigation was the development of a viable plane strain two dimensional non linear finite element analysis code which can predict the stress - strain behaviour of gabion faced retaining walls - both gravity type and reinforced soil type. The gabion facing, backfill soil, In - situ soil and foundation soil were modelled using 20 four noded isoparametric quadrilateral elements. The confinement provided by the gabion boxes was converted into an induced apparent cohesion as per the membrane correction theory proposed by Henkel and Gilbert (1952). The mesh reinforcement was modelled using 20 two noded linear truss elements. The interactions between the soil and the mesh reinforcement as well as the facing and backfill were modelled using 20 four noded zero thickness line interface elements (Desai et al., 1974) by incorporating the nonlinear hyperbolic formulation for the tangential shear stiffness. The well known hyperbolic formulation by Ouncan and Chang (1970) was used for modelling the non - linearity of the soil matrix. The failure of soil matrix, gabion facing and the interfaces were modelled using Mohr - Coulomb failure criterion. The construction stages were also modelled.Experimental investigations were conducted on small scale model walls (both in field as well as in laboratory) to suggest an alternative fill material for the gabion faced retaining walls. The same were also used to validate the finite element programme developed as a part of the study. The studies were conducted using different types of gabion fill materials. The variation was achieved by placing coarse aggregate and quarry dust in different proportions as layers one above the other or they were mixed together in the required proportions. The deformation of the wall face was measured and the behaviour of the walls with the variation of fill materials was analysed. It was seen that 25% of the fill material in gabions can be replaced by a soft material (any locally available material) without affecting the deformation behaviour to large extents. In circumstances where deformation can be allowed to some extents, even up to 50% replacement with soft material can be possible.The developed finite element code was validated using experimental test results and other published results. Encouraged by the close comparison between the theory and experiments, an extensive and systematic parametric study was conducted, in order to gain a closer understanding of the behaviour of the system. Geometric parameters as well as material parameters were varied to understand their effect on the behaviour of the walls. The final phase of the study consisted of developing a simplified method for the design of gabion faced retaining walls. The design was based on the limit state method considering both the stability and deformation criteria. The design parameters were selected for the system and converted to dimensionless parameters. Thus the procedure for fixing the dimensions of the wall was simplified by eliminating the conventional trial and error procedure. Handy design charts were developed which would prove as a hands - on - tool to the design engineers at site. Economic studies were also conducted to prove the cost effectiveness of the structures with respect to the conventional RCC gravity walls and cost prediction models and cost breakdown ratios were proposed. The studies as a whole are expected to contribute substantially to understand the actual behaviour of gabion faced retaining wall systems with particular reference to the lateral deformations.

Resource abundance and Survival of indigenous ornamental fishes of central Kerala with emphasis on handling and packing stress in Puntius filamentosus(VALENCIENNES)

This thesis Entitled Resource abundance and survival of indigenous ornamental fishes of central kerala with emphasis on handling and packing stress in puntius filamentosus (valenciennes).Kerala state is endowed with 41 west flowing and three east flowing rivers originating in the Western Ghats. These rivers and their vast network of tributaries and distributaries harbour rich and diversified fish fauna. Most of the freshwater fishes available in Kerala are highly appreciated as ornamental fishes in the national and international markets.Today the ornamental fish industry is one of the largest industries all over the world. The demand for ornamental fishes has been increasing steadily with the enlargement of the industry, such that the current demand for indigenous ornamental fishes have exceeded the supply. This has led to serious concern about the resources available in the country that can be utilised judiciously for the economic benefit of the state. With an aim to fill up the lacuna, a database of freshwater ornamental fishes of Kerala was created as part of the present study. Ornamental fishes destined for export marketing should thrive well in the aquarium conditions.The study reiterates fishes caught from different environmental conditions and feeding habits have a greater ability to adapt and acclimatise to an entirely new environment and food habits. Marketing studies based on the statistics available with Marine Products Export Development Authority show that these species are not being exported at the required level over the past 6 years, when compared to the availability in the water bodies of Kerala. Sustainable utilisation of these resources from the wild using modern management principles and code of conduct for responsible fishing are advisable until captive breeding technology is popularised.

IA Critical Study of the Impact of Institutional Finance on Agriculture in Selected Villages of Ernakulam Revenue District

Vast changes have taken place in the field of institutional rural credit in India since the nationalisation of nineteen commercial banks in 1969. The supply of institutional finance to cultivators amounted to 63.2 percent of the total credit in 1981 compared to 31.2 percent in 1971. Insti tutionalisation of agricultural credit envisaged two objectives in general. One was to emancipate cultivators and farmers from the clutches of indigenous financiers and money lenders. The second was to make farmers financially capable of adopting the new technology or improved practices in agriculture so as to increase their agricultural production and thereby contributing to the development of agriculture in India. Though vast literature on Institutional Credi t and agriculture is available, no indepth and serious work examining thoroughly the cause of credit diversion has been undertaken so far. The present study is an attempt to fill up this gap. The study will be helpful to lending insti tutions, viz. Co-ope:r-atives, Commercial banks and various other insti tutional agencies in connection with their lending activity_ Also, the study will help government in .formulating proper policies that will insure a preferential treatment in favour of the most needy category of farmers and cultivators with respect to agricultural credit disbursement

Financial planning and Control in public sector undertakings in kerala

Today India is seeking a speedy transformation of her semi-stagnant economy to a dynamic one by means of economic planning in a democratic set up. In the context of this growth oriented endeavour public sector has a vital role to play. After three decades of planned development, it has become important that India must make fresh appraisals on the role of public sector in the economic renaissance of the country. Almost no comprehensive study has been made on this vital segment of the economy vis-a-vis the growth economics. This study is an attempt to fill this need in a very modest way. It presents the subject in a new perspective. An earnest attempt is made to reveal the critical problems inhibiting the growth of the public sector from a new angle which focusses the spot-light on the economics of development.

On the synthesis and magnetic properties of multiwall carbon nanotube– superparamagnetic iron oxide nanoparticle nanocomposites

Multiwall carbon nanotubes (MWCNTs) possessing an average inner diameter of 150 nm were synthesized by template assisted chemical vapor deposition over an alumina template. Aqueous ferrofluid based on superparamagnetic iron oxide nanoparticles (SPIONs) was prepared by a controlled co-precipitation technique, and this ferrofluid was used to fill the MWCNTs by nanocapillarity. The filling of nanotubes with iron oxide nanoparticles was confirmed by electron microscopy. Selected area electron diffraction indicated the presence of iron oxide and graphitic carbon from MWCNTs. The magnetic phase transition during cooling of the MWCNT–SPION composite was investigated by low temperature magnetization studies and zero field cooled (ZFC) and field cooled experiments. The ZFC curve exhibited a blocking at ∼110 K. A peculiar ferromagnetic ordering exhibited by the MWCNT–SPION composite above room temperature is because of the ferromagnetic interaction emanating from the clustering of superparamagnetic particles in the constrained volume of an MWCNT. This kind of MWCNT–SPION composite can be envisaged as a good agent for various biomedical applications

CuInS2/In2S3 Cells using a Cost-effective Technique: Significance of Precursor Ratios on Cell Parameters

Thin film solar cells having structure CuInS2/In2S3 were fabricated using chemical spray pyrolysis (CSP) technique over ITO coated glass. Top electrode was silver film (area 0.05 cm2). Cu/In ratio and S/Cu in the precursor solution for CuInS2 were fixed as 1.2 and 5 respectively. In/S ratio in the precursor solution for In2S3 was fixed as 1.2/8. An efficiency of 0.6% (fill factor -37.6%) was obtained. Cu diffusion to the In2S3 layer, which deteriorates junction properties, is inevitable in CuInS2/In2S3 cell. So to decrease this effect and to ensure a Cu-free In2S3 layer at the top of the cell, Cu/In ratio was reduced to 1. Then a remarkable increase in short circuit current density was occurred from 3 mA/cm2 to 14.8 mA/cm2 and an efficiency of 2.13% was achieved. Also when In/S ratio was altered to 1.2/12, the short circuit current density increased to 17.8 mA/cm2 with an improved fill factor of 32% and efficiency remaining as 2%. Thus Cu/In and In/S ratios in the precursor solutions play a crucial role in determining the cell parameters

Measuring the Maturity of Open Source Software for Digital Libraries: a Case Study of DSpace

The assessment of maturity of software is an important area in the general software sector. The field of OSS also applies various models to measure software maturity. However, measuring maturity of OSS being used for several applications in libraries is an area left with no research so far. This study has attempted to fill the research gap. Measuring maturity of software contributes knowledge on its sustainability over the long term. Maturity of software is one of the factors that positively influence adoption. The investigator measured the maturity of DSpace software using Woods and Guliani‟s Open Source Maturity Model-2005. The present study is significant as it addresses the aspects of maturity of OSS for libraries and fills the research gap on the area. In this sense the study opens new avenues to the field of library and information science by providing an additional tool for librarians in the selection and adoption of OSS. Measuring maturity brings in-depth knowledge on an OSS which will contribute towards the perceived usefulness and perceived ease of use as explained in the Technology Acceptance Model theory.

Studies on Selected Myctophid Fishes in Arabian Sea with respect to their Status in Deep Sea Trawl Bycatch, Length-Weight Relationship, Reproductive Biology and Population Dynamics

Available information on abundance of myctophids and their utilisation indicate that there is excellent scope for development of myctophid fisheries in Indian Ocean. Most of the conventional fish stocks have reached a state of full exploitation or over-exploitation. Hence there is need to locate new and conventional fishery resources in order to fill in the supply-demand gap, in the face of increasing demand for fish. Information on length-weight relationship, age and growth, spawning season, fecundity and age at maturity and information on bycatch discards are required for sustainable utilization of myctophid resource in the Indian Ocean

A Study on Futures Trading in Commodities With Special Reference to Rubber

Futures trading in Commodities has three specific economic functions viz. price discovery, hedging and reduction in volatility. Natural rubber possesses all the specifications required for futures trading. Commodity futures trading in India attained momentum after the starting of national level commodity exchanges in 2003. The success of futures trading depends upon effective price risk management, price discovery and reduced volatility which in turn depends upon the volume of trading. In the case of rubber futures market, the volume of trading depends upon the extent of participation by market players like growers, dealers, manufacturers, rubber marketing co-operative societies and Rubber Producer’s Societies (RPS). The extent of participation by market players has a direct bearing on their awareness level and their perception about futures trading. In the light of the above facts and the review of literature available on rubber futures market, it is felt that a study on rubber futures market is necessary to fill the research gap, with specific focus on (1) the awareness and perception of rubber futures market participants viz. (i) rubber growers, (ii) dealers, (iii) rubber product manufacturers, (iv) rubber marketing co-operative societies and Rubber Producer’s Societies (RPS) about futures trading and (2) whether the rubber futures market is fulfilling the economic functions of futures market viz. hedging, reduction in volatility and price discovery or not. The study is confined to growers, dealers, rubber goods manufacturers, rubber marketing co-operative societies and RPS in Kerala. In order to achieve the stated objectives, the study utilized secondary data for the period from 2003 to 2013 from different published sources like bulletins, newsletters, circulars from NMCE, Reserve Bank of India (RBI), Warehousing Corporation and traders. The primary data required for this study were collected from rubber growers, rubber dealers, RPS & Rubber Marketing Co-operative Societies and rubber goods manufacturers in Kerala. Data pertaining to the awareness and perception of futures trading, participation in the futures trading, use of spot and futures prices and source of price information by dealers, farmers, manufacturers and cooperative societies also were collected. Statistical tools used for analysis include percentage, standard deviation, Chi-square test, Mann – Whitney U test, Kruskal Wallis test, Augmented Dickey – Fuller test statistic, t- statistic, Granger causality test, F- statistic, Johansen co – integration test, Trace statistic and Max –Eigen statistic. The study found that 71.5 per cent of the total hedges are effective and 28.5 per cent are ineffective for the period under study. It implies that futures market in rubber reduced the impact of price risks by approximately 71.5 per cent. Further, it is observed that, on 54.4 per cent occasions, the futures market exercised a stabilizing effect on the spot market, and on 45.6 per cent occasions futures trading exercised a destabilizing effect on the spot market. It implies that elasticity of expectation of futures market in rubber has a predominant stabilizing effect on spot prices. The market, as a whole, exhibits a bias in favour of long hedges. Spot price volatility of rubber during futures suspension period is more than that of the pre suspension period and post suspension period. There is a bi-directional association-ship or bi-directional causality or pair- wise causality between spot price and futures price of rubber. From the results of the hedging efficiency, spot price volatility, and price discovery, it can be concluded that rubber futures market fulfils all the economic functions expected from a commodity futures market. Thus in India, the future of rubber futures is Bright…!!!