An Integrated Hydro geological Study of the Muvattupuzha River Basin, Kerala, India

The present investigation on the Muvattupuzha river basin is an integrated approach based on hydrogeological, geophysical, hydrogeochemical parameters and the results are interpreted using satellite data. GIS also been used to combine the various spatial and non-spatial data. The salient finding of the present study are accounted below to provide a holistic picture on the groundwaters of the Muvattupuzha river basin. In the Muvattupuzha river basin the groundwaters are drawn from the weathered and fractured zones. The groundwater level fluctuations of the basin from 1992 to 2001 reveal that the water level varies between a minimum of 0.003 m and a maximum of 3.45 m. The groundwater fluctuation is affected by rainfall. Various aquifer parameters like transmissivity, storage coefficient, optimum yield, time for full recovery and specific capacity indices are analyzed. The depth to the bedrock of the basin varies widely from 1.5 to 17 mbgl. A ground water prospective map of phreatic aquifer has been prepared based on thickness of the weathered zone and low resistivity values (<500 ohm-m) and accordingly the basin is classified in three phreatic potential zones as good, moderate and poor. The groundwater of the Muvattupuzha river basin, the pH value ranges from 5.5 to 8.1, in acidic nature. Hydrochemical facies diagram reveals that most of the samples in both the seasons fall in mixing and dissolution facies and a few in static and dynamic natures. Further study is needed on impact of dykes on the occurrence and movement of groundwater, impact of seapages from irrigation canals on the groundwater quality and resources of this basin, and influence of inter-basin transfer of surface water on groundwater.

Inertial oscillation forced by the September 1997 cyclone in the Bay of Bengal

Time-series measurements from a moored data buoy located in the Bay of Bengal captured signals of inertial oscillation forced by the September 1997 cyclone. The progressive vector diagram showed mean northeastward current with well-defined clockwise circulation. Spectral analysis exhibited inertial peak at 0.67 cpd with blue shift and high rotary coefficient of –0.99, which signifies strong circular inertial oscillation. The wind and SST also exhibited spectral peak at inertial band (0.69 cpd) with higher blue shift. The inertial amplitude of 148.8 cm/s corresponding to a wind stress of 0.99 N/m2 and spectral peak near the local inertial frequency (0.653 cpd) indicate that the transfer of momentum was high.

Marine Engineering Training in India -A Pedagogic Introspection

Indian marine engineers are renowned for employment globally due to their knowledge, skill and reliability. This praiseworthy status has been achieved mainly due to the systematic training imparted to marine engineering cadets. However, in an era of advancing technology, marine engineering training has to remain dynamic to imbibe latest technology as well as to meet the demands of the shipping industry. New subjects of studies have to be included in the curriculum in a timely manner taking into consideration the industry requirements and best practices in shipping. Technical competence of marine engineers also has to be subjected to changes depending upon the needs of the ever growing and over regulated shipping industry. Besides. certain soft skills are to be developed and improved amongst the marine engineers in order to alter or amend the personality traits leading to their career success.If timely corrective action is taken. Indian marine engineers can be in still greater demand for employment in global maritime field. In order to enhance the employability of our mmine engineers by improving their quality, a study of marine engineers in general and class IV marine engineers in particular was conducted based on three distinct surveys, viz., survey among senior marine engineers, survey among employers of marine engineers and survey of class IV marine engineers themselves.The surveys have been planned and questionnaires have been designed to focus the study of marine engineer officer class IV from the point of view of the three distinct groups of maritime personnels. As a result of this, the strength and weakness of class IV marine engineers are identified with regard to their performance on board ships, acquisition of necessary technical skills. employability and career success. The criteria of essential qualities of a marine engineer are classified as academic, technical, social, psychological. physical, mental, emergency responsive, communicative and leadership, and have been assessed for a practicing marine engineer by statistical analysis of data collected from surveys. These are assessed for class IV marine engineers from the point of view of senior marine engineers and employers separately. The Endings are delineated and graphically depicted in this thesis.Besides. six pertinent personality traits of a marine engineer viz. self esteem. learning style. decision making. motivation. team work and listening self inventory have been subjected to study and their correlation with career success have been established wherever possible. This is carried out to develop a theoretical framework to understand what leads a marine engineer to his career attainment. This enables the author to estimate the personality strengths and weaknesses of a serving marine engineer and eventually to deduce possible corrective measures or modifications in marine engineering training in India.Maritime training is largely based on International Conventions on Standard of Training. Certification and Watch keeping for Seafarers 1995. its associated Code and Merchant Shipping (STCW for Seafarers) Rules 1998. Further, Maritime Education, Training and Assessment (META) Manual was subjected to a critical scrutiny and relevant Endings of thc surveys arc superimposed on the existing rule requirement and curriculum. Views of senior marine engineers and executives of various shipping companies are taken into account before arriving at the revision of syllabus of marine engineering courses. Modifications in the pattern of workshop and sea service for graduate mechanical engineering trainees are recommended. Desirable age brackets of junior engineers and chief engineers. use of Training and Assessment Record book (TAR Book) during training etc. have also been evaluated.As a result of the pedagogic introspection of the existing system of marine engineering training in India. in this thesis, a revised pattern of workshop training of six months duration for graduate mechanical engineers. revised pattern of sea service training of one year duration and modified now diagram incorporating the above have been arrived at. Effects of various personality traits on career success have been established along with certain findings for improvement of desirable personality traits of marine engineers.

An Error-Localization, Validation and Optimization Tool for Embedded Code Augmentation: an Architecture Oriented Approach

Embedded systems are usually designed for a single or a specified set of tasks. This specificity means the system design as well as its hardware/software development can be highly optimized. Embedded software must meet the requirements such as high reliability operation on resource-constrained platforms, real time constraints and rapid development. This necessitates the adoption of static machine codes analysis tools running on a host machine for the validation and optimization of embedded system codes, which can help meet all of these goals. This could significantly augment the software quality and is still a challenging field.Embedded systems are usually designed for a single or a specified set of tasks. This specificity means the system design as well as its hardware/software development can be highly optimized. Embedded software must meet the requirements such as high reliability operation on resource-constrained platforms, real time constraints and rapid development. This necessitates the adoption of static machine codes analysis tools running on a host machine for the validation and optimization of embedded system codes, which can help meet all of these goals. This could significantly augment the software quality and is still a challenging field.Embedded systems are usually designed for a single or a specified set of tasks. This specificity means the system design as well as its hardware/software development can be highly optimized. Embedded software must meet the requirements such as high reliability operation on resource-constrained platforms, real time constraints and rapid development. This necessitates the adoption of static machine codes analysis tools running on a host machine for the validation and optimization of embedded system codes, which can help meet all of these goals. This could significantly augment the software quality and is still a challenging field.Embedded systems are usually designed for a single or a specified set of tasks. This specificity means the system design as well as its hardware/software development can be highly optimized. Embedded software must meet the requirements such as high reliability operation on resource-constrained platforms, real time constraints and rapid development. This necessitates the adoption of static machine codes analysis tools running on a host machine for the validation and optimization of embedded system codes, which can help meet all of these goals. This could significantly augment the software quality and is still a challenging field.This dissertation contributes to an architecture oriented code validation, error localization and optimization technique assisting the embedded system designer in software debugging, to make it more effective at early detection of software bugs that are otherwise hard to detect, using the static analysis of machine codes. The focus of this work is to develop methods that automatically localize faults as well as optimize the code and thus improve the debugging process as well as quality of the code.Validation is done with the help of rules of inferences formulated for the target processor. The rules govern the occurrence of illegitimate/out of place instructions and code sequences for executing the computational and integrated peripheral functions. The stipulated rules are encoded in propositional logic formulae and their compliance is tested individually in all possible execution paths of the application programs. An incorrect sequence of machine code pattern is identified using slicing techniques on the control flow graph generated from the machine code.An algorithm to assist the compiler to eliminate the redundant bank switching codes and decide on optimum data allocation to banked memory resulting in minimum number of bank switching codes in embedded system software is proposed. A relation matrix and a state transition diagram formed for the active memory bank state transition corresponding to each bank selection instruction is used for the detection of redundant codes. Instances of code redundancy based on the stipulated rules for the target processor are identified.This validation and optimization tool can be integrated to the system development environment. It is a novel approach independent of compiler/assembler, applicable to a wide range of processors once appropriate rules are formulated. Program states are identified mainly with machine code pattern, which drastically reduces the state space creation contributing to an improved state-of-the-art model checking. Though the technique described is general, the implementation is architecture oriented, and hence the feasibility study is conducted on PIC16F87X microcontrollers. The proposed tool will be very useful in steering novices towards correct use of difficult microcontroller features in developing embedded systems.

Phenylethynylarene Based Donor-Acceptor Systems: Design, Synthesis and Photophysical Studies

This thesis Entitled phenylethynylarene based Donor-Acceptor systems:Desigh,Synthesis and Photophysical studies. A strategy for the design of donor-acceptor dyads, wherein decay of the charge separated (CS) state to low lying local triplet levels could possibly be prevented, is proposed. In order to examine this strategy, a linked donor-acceptor dyad BPEPPT with bis(phenylethYlly/)pyrene (BPEP) as the light absorber and acceptor and phenothiazine (PT) as donor was designed and photoinduced electron transfer in the dyad investigated. Absorption spectra of the dyad can be obtained by adding contributions due 10 the BPEP and PT moieties indicating that the constituents do not interact in the ground stale. Fluorescence of the BPEP moiety was efficiently quenched by the PT donor and this was attributed to electron lransfer from PT to BPEP. Picosecond transient absorption studies suggested formation of a charge separated state directly from the singlet excited state of BPEP. Nanosecond flash photolysis experiments gave long-ived transient absorptions assignable to PT radical cation and BPEP radical anion. These assignments were confirmed by oxygen quenching studies and secondary electron transfer experiments. Based on the available data, energy level diagram for BPEP-PT was constructed. The long lifetime of the charge separated state was attributed to the inverted region effects. The CS state did not undergo decay to low lying BPEP triplet indicating the success of our strategy

Modeling Of Work-Related Musculoskeletal Disorders In Chemical Process Industry In India

In this modern complex world, stress at work is found to be increasingly a common feature in day to day life. For the same reason, job stress is one of the active areas in occupational health and safety research for over last four decades and is continuing to attract researchers in academia and industry. Job stress in process industries is of concern due to its influence on process safety, and worker‘s safety and health. Safety in process (chemical and nuclear material) industry is of paramount importance, especially in a thickly populated country like India. Stress at job is the main vector in inducing work related musculoskeletal disorders which in turn can affect the worker health and safety in process industries. In view of the above, the process industries should try to minimize the job stress in workers to ensure a safe and healthy working climate for the industry and the worker. This research is mainly aimed at assessing the influence of job stress in inducing work related musculoskeletal disorders in chemical process industries in India

EVALUATION OF THERMODYNAMIC PARAMETERS OF THE ATMOSPHERE BY A FORTRAN PROGRAM

Thermodynamic parameters of the atmosphere form part of the input to numerical forecasting models. Usually these parameters are evaluated from a thermodynamic diagram. Here, a technique is developed to evaluate these parameters quickly and accurately using a Fortran program. This technique is tested with four sets of randomly selected data and the results are in agreement with the results from the conventional method. This technique is superior to the conventional method in three respects: more accuracy, less computation time, and evaluation of additional parameters. The computation time for all the parameters on a PC AT 286 machine is II sec. This software, with appropriate modifications, can be used, for verifying various lines on a thermodynamic diagram

Face Recognition using Probabilistic Neural Networks

In this paper we address the problem of face detection and recognition of grey scale frontal view images. We propose a face recognition system based on probabilistic neural networks (PNN) architecture. The system is implemented using voronoi/ delaunay tessellations and template matching. Images are segmented successfully into homogeneous regions by virtue of voronoi diagram properties. Face verification is achieved using matching scores computed by correlating edge gradients of reference images. The advantage of classification using PNN models is its short training time. The correlation based template matching guarantees good classification results

Face Recognition using Probabilistic Neural Networks

n this paper we address the problem of face detection and recognition of grey scale frontal view images. We propose a face recognition system based on probabilistic neural networks (PNN) architecture. The system is implemented using voronoi/ delaunay tessellations and template matching. Images are segmented successfully into homogeneous regions by virtue of voronoi diagram properties. Face verification is achieved using matching scores computed by correlating edge gradients of reference images. The advantage of classification using PNN models is its short training time. The correlation based template matching guarantees good classification results.

Energy bandstructureinvestigationofblueandgreenlightemitting Mg dopedSnO2 nanostructuressynthesizedbycombustionmethod

Tin oxide(SnO2) andMgdoped(2,4,6,and8wt%)SnO2 nanoparticles weresynthesizedbytheself- propagating solutioncombustionsynthesisusingcitricacidasfuel.Thecharacterizationofsampleswas done byX-raydiffractionspectroscopy(XRD),transmissionelectronmicroscopy(TEM),UV–visible spectroscopy,SAEDandphotoluminescence(PL).XRDpatternandTEMstudiesshowthatthe synthesized particlesareofaveragesize30nmandtheyareintetragonalrutilestructureofSnO2. Combined blueandgreenemissionisseenin4wt%MgdopedSnO2 and intensityofbluebandis increased withrespecttoincreaseinMgdopantconcentrationwhichisattributedtoincreasein population ofoxygenvacancies.ThePLemissioninblueandgreenregionisduetothedoublycharged state (Vo 2þ) ofoxygenandtininterstitialdefectsrespectivelyandisexplainedwithanenergyband diagram

Photoluminescence Studies Of Microwave Assisted Synthesized Zno Micro Structures

ZnO micro particles in the range 0.4-0.6 μm were synthesized by microwave irradiation method. The XRD analysis reveals that the sample is in the wurtzite phase with orientation along the (101) plane. SAED pattern of the sample reveals the single crystalline nature of the micro grains. TEM images show the formation of cylindrical shaped ZnO micro structures with hexagonal faces. The optical phonon modes were slightly shifted in the Raman spectrum,attributed to the presence of various crystalline defects and laser induced local heating at the grain boundaries. A broad transmission profile was observed in the FTIR spectrum from 1550-3400 cm-1 which falls in the atmospheric transparency window region. PL spectrum centered at 500 nm with a broad band in the region 420-570 nm comprised of different emission peaks attributed to transition between defect levels. Various emission levels in the sample were expliained with a band diagram