DB. BAMKIIMAH VARMA KA KAVYA

HINDI

Frequency tunable metallo–dielectric structure for backscattering reduction

Electromagnetic scattering behaviour of a superstrate loaded metallo– dielectric structure based on Sierpinski carpet fractal geometry is reported. The results indicate that the frequency at which backscattering is minimum can be tuned by varying the thickness of the superstrate. A reduction in backscattered power of 44 dB is obtained simultaneously for both TE and TM polarisations of the incident field.

Broadband Cylindrical Dielectric Resonator Antenna Excited by Modified Microstrip Line

The impedance bandwidth of a high permittivity cylindrical dielectric resonator antenna excited by a micro strip line was significantly improved by modifying the feed geometry. The 10 dB return loss bandwidth is enhanced from 12 to 26% without much affecting the gain and other radiation properties of the antenna. Good agreement has been observed between the predicted and measured results

Backscattering Reduction of Corner Reflectors using SCS Technique

Reduction of radar cross -section of dihedral corner reflectors using simulated corrugated surface (.SCS) is reported. This technique is found lo be more effective in the reduction of RCS or corner reflectors for normal incidence . A typical reduction of 40-50 dB is achieved using this method

Dielecting-resonator-loaded microstrip antenna for enhanced impedance bandwidth and efficiency

A new method for enhancing the 2.1 VSWR impedance bandwidth of microstrip antennas is presented. Bandwidth enhancement is achieved by loading the microstrip antenna by a ceramic microwave dielectric resonator (DR). The validity of this technique has been established using rectangular and circular radiating geometries. This method improves the bandwidth of a rectangular microstrip antenna to more than 10% (= 5 times that of a conventional rectangular microstrip antenna) with an enhanced gain of I dB

Circularly Polarized Compact Microstrip Antenna

A compact microstrip antenna with circular polarization radiation is demonstrated.A reducation in the required parameters for achieving CP radiation makes the present antenna design simpler

Compact Circular- Sided Microstrip Antenna for Circular Polarization

Development of a new compact circular-sided microstrip antenna is presented. This antenna offers considerable area re- TABLE 2. Variation of Resonant Frequencies duction compared to standard rectangular microstrip antenna designed for the same frequency. Typical antenna design and experimental results for circular polarization are also demonstrated. 77je antenna has a 3-dB axial ratio bandwidth of 1.5%

Dual-Port Dual-Polarized Microstrip Antenna

Experimental and simulated results for a dual-port dual-polarized microstrip antenna are presented. The antenna excites two orthogonally polarized resonant frequencies providing an isolation of -30 dB between the ports. The patch geometry consists of two circular arcs of different radii with their centers displaced by a distance. This new design offers an area reduction of -70% coinpared to it standard rectangular microstrip antenna with a reduction in gain of 1.7 dB

Analysis and Design of a Dual-Port Compact Microstrip Antenna

A dual-port dual-polarized compact microstrip antenna for avoiding cross coupling between the two frequency bands is proposed and analyzed. This antenna offers channel isolation better than 25 dB, and is more compact compared to a conventional rectangular patch. Analytical equations for calculating the resonant frequencies at both ports are also presented. The theoretical calculations are verified using experimental results

A Wideband Rectangular Microstrip Antenna Using an Asymmetric t-shaped Feed

An electromagnetically coupled T-shaped microstrip feed used to enhance the impedance bandwidth of a rectangular microstrip antenna is reported. The proposed antenna offers a 2:1 VSWR bandwidth of -36% with an increase in gain of 0.8 dB

Compact amplifier integrated microstrip antenna

compact microstrip antenna integrated with an amplifier having an area reduction of 70%, compared to the standard circular microstrip patch antenna, is presented. The antenna also provides an enhanced gain of 10-dB more than its passive counter part. The measured 2:1 VSWR band width is -4% at 790 MHz, which is 2.5 times larger than that of the passive microstrip antenna

A Broadband Slope-Strip-Fed Micro strip Patch Antenna

A novel slope -strip feeding technique for a microstrip antenna is presented in order to achieve a broad bandwidth. The experimental results show that the optimal bandwidth attained is 53.4% for less than -10-dB return loss

Low backscattered dual-polarised metallo-dielectric structure based on sierpinski carpet

A novel technique for backscattering reduction for both TE and TM polarisation, employing a metallo-dielectric structure based on Sierpinski carpet fractal geometry, is reported. A reduction in backscattered power of --30 dB is obtained for normal incidence in the X-band for the structure using the third iterated stage of the fractal geometry

A Novel Method for Switching and Tuning of PBG Structures

Photonic band-gap (PBG) structures are utilized in microwave components as filters to suppress unwanted signals. In this work, rectangular perforations were created in the ground plane of a microstrip line to construct a PBG structure. A gold-coated alumina substrate was utilized to switch or tune the bandstop characteristics of this structure. It was demonstrated that the bandstop characteristics were switched off from - 35 to - 1 dB at 16 GHz. Tuning of the bandstop edge with a shift of 1.5 GHz was also shown

Analysis and Testing of a Novel Oadm Based on FBG and Machzehnder Interferometer

A novel optical add-drop multiplexer (OADM) based on the Mach-Zelauler interferometer (MZI) and the fiber Bragg grating (FBG) is proposed for the first tittle to the authors ' knowledge. In the structure, the Mach-Zehnder interferometer acts as an optical switch. The principle of the OADM is analyzed in this paper. The OADM can add/drop one of the multi-input channels or pass the channel directly by adjusting the difference of the two arms of the interferometer. The channel isolation is more than 20 dB