Studies on adhesives for bonding rubber to rubber and rubber to textiles

The primary objective of this investigation has been to develop more efficient and low cost adhesives for bonding various elastomer combinations particularly NR to NR, NR/PB to NR/PB, CR to CR,NR to CR and NR to NBR.A significant achievement of the investigation was the development of solventless and environment friendly solid adhesives for NR to NR and NR/PB to NR/PB particularly for precured retreading. Conventionally used adhesives in this area are mostly NR based adhesive strips in the presence of a dough. The study has shown that an ultra accelerator could be added to the dough just before applying it on the tire which can significantly bring down the retreading time resulting in prolonged tire service and lower energy consumption. Further latex reclaim has been used for the preparation of the solid strip which can reduce the cost considerably.Another significant finding was that by making proper selection of the RF resin, the efficiency and shelflife of the RFL adhesive used for nylon and rayon tire cord dipping can be improved. In the conventionally used RFL adhesive, the resin once prepared has to be added to the latex within 30 minutes and the RFL has to be used after 4 hours maturation time maximum shelf life of the RFL dip solution being 72 hours. In this study a formaldehyde deficient resin was used and hence more flexibility was available for mixing with latex and maturing. It also has a much longer shelf life. In the method suggested in this study, formaldehyde donors were added only in the rubber compound to make up the formaldehyde deficiency in the RFL. The results of this investigation show that the pull through load by employing this method and the conventional method are comparable. This study has also shown that the amount of RF resin with RFL adhesive can be partially replaced by other modifying agents for cost reduction.Cashew nut shell liquid (CNSL) resin can be employed for improving the bonding of dipped nylon and rayon cord with NR.Since CNSL resin cannot be added in the dip solution since it is not soluble in water, it was added in the rubber compound. The amount of wood rosin in the rubber compound can be reduced by using CNSL resin.Another interesting result of the investigation was the use of CR based adhesive modified with chlorinated natural rubber for CR to CR bonding. Addition of chlorinated natural rubber was found to improve sea water resistance of CR based adhesive. In the bonding of a polar rubber like nitrile rubber or polychloroprene rubber to a non polar rubber like natural rubber, an adhesive based on polychloroprene rubber was found to be effective.

Inventory management in public sector electrical industry in Kerala

The thesis entitled Inventory Management In Public Sector Electrical Industry In Kerala. Investigations were carried out on inventory management in public sector electrical industry in Kerala and suggest methods to improve their efficiency. Various aspects of inventory management, its scope and need in industry are detailed. The objectives of the present study concentrates to get an overall view of the system of inventory management, assess the positions and levels of inventory. It analyzes the inventory management policies and practices, the organizational set-up for materials by the electrical undertakings. The study examines the liquidity of the electrical undertakings as well as techniques of inventory management in the electrical industry in Kerala. Hypotheses state that the existing organizational systems and practices are inadequate to ensure efficient management of inventories in electrical industry. Introduction of scientific inventory techniques has a favourable effect on the workings of inventory departments. The financial performance of the public sector electrical undertakings is not at all satisfactory on account of the high raw material costs, heavy borrowings and huge interest burdens. The scope of this study is limited to the assessment of savings, in inventories of electrical products due to inventory management. The methodology of the study is to project the cost reduction of the inventory department on the basis of data collected and to validate this projection with the aid of analysis and survey. The limitations of the study is that the data obtained relate to the period 1989-90 and earlier and the current position is not available and uniform norms cannot be applied to evaluate different inventory management organisation.

Development and parametric studies of pulsed nitrogen and d-switched nd:glass lasers and some of their applications

Laser engineering is an area in which developments in the existing design concepts and technology appear at an alarming rate. Now—a-days, emphasis has shifted from innovation to cost reduction and system improvement. To a major extent, these studies are aimed at attaining larger power densities, higher system efficiency and identification of new lasing media and new lasing wavelengths. Todate researchers have put to use all the ditferent Forms of matter as lasing material. Laser action was observed For the first time in a gaseous system - the He-Ne system. This was Followed by a variety of solidstate and gas laser systems. Uarious organic dyes dissolved in suitable solvents were found to lase when pumped optically. Broad band emission characteristics of these dye molecules made wavelength tuning possible using optical devices. Laser action was also observed in certain p-n junctions of semiconductor materials and some of these systems are also tunable. The recent addition to this list was the observation of laser action from certain laser produced plasmas. The purpose of this investigation was to examine the design and Fabrication techniques of pulsed Nitrogen lasers and high power Nd: Glass laserso Attempt was also made to put the systems developed into certain related experiments