Study on Solid Waste Management : An Economic Analysis with Respect to Ernakulam District

This thesis analyzed waste generation and waster disposal problems in municipalities and Cochin Corporation in Ernakulam district.Then the potential of resource recovery and recycling from biodegradable and non bio-degradable waste is established.The study further focused on the need for segregation of waste at the source as biodegradable and non biodegradable solid waste.The potential of resource recovery is explained in detail through the case study.The thesis also highlights the economically viable and environmental friendly methods o f treatment of waste.But the problem is that concerted and earnest attempts are lacking in making use of such methods.In spite of the health problems faced,people living near the dump sites are forced to stay there either because of their weak economic background or family ties.The study did not calculate the economic cost of health problems arising out of unscientific and irresponsible methods of waste disposal.

Solid Waste Management: A Case Study of Arppukara Grama Panchayat Of Kottayam District, Kerala (India)

The rising pressure of Population, together with the constantly changing technologies, and development perspectives, contribute to the ever increasing volumes of wastes in different forms. The solid and liquid wastes generated in the urban areas were considered a burden to the society, and hazardous to the environment. The fact is that the growth of consumerist culture and aimless throwing of refuse by the people created the outbreak of environmental pollution. Unhygienic environment and solid waste accumulation coincided with mosquito breeding which causes, the spread of most epidemics. The rationale behind most of the diseases is the unhygienic pattern followed by the people both in rural and urban areas. As an environmental package, the disposal of solid waste from different sources, such as house holds markets, commercial areas, slaughter houses, hospitals and industries, therefore assumed crucial importance. So as a part of the theory and practice, a study on the area, solid waste management of Arppukara Grama Panchayat of Kottayam district is taken into consideration. The study conducted here proposes, to examine the quality and quantity of the solid waste generated in the panchayat and also it's impact on the existing social, economical, environmental and ecological systems

Standardization of Optimum Conditions for the Production of Glucosamine Hydrochiloride from Chitin

The study entitled standardization of optimum conditions for the production of glucosamine hydrochloride from chitin. Shellfish processing industries around the world turn out a significant quantity of head and shell as industrial waste. The waste must be removed immediately to prevent the contamination to the processing environment. The technique that are available for their disposal include ocean dumping, incineration or disposal of landfill sites. In this thesis the techniques and methods are used to process glucosamine hydrochloride from crustacean processing waste. Chitin is a nitrogenous polysaccharide, which is white, hard, inelastic, found in outer skeleton of insects, crabs, shrimp and lobsters and in the internal structures of other invertebrates. Glucosamine can be considered as a nutraceutical product by virtue of its properties. It is important for healthy skin, and plays a major role in the healing of surgical incisions and skin wounds. Deproteinisation of shrimp shell had significant effect on quality of chitin. Demineralization is also influences chitin quality. Solvents used for glucosamine hydrochloride affects the final yield and purity.

Ionomer Compatibilized Low Density Polyethylene - Tapioca Starch Blends Biodegradability and Photodegradability

Biodegradation is the chemical degradation of materials brought about by the action of naturally occurring microorganisms. Biodegradation is a relatively rapid process under suitable conditions of moisture, temperature and oxygen availability. The logic behind blending biopolymers such as starch with inert polymers like polyethylene is that if the biopolymer component is present in sufficient amount, and if it is removed by microorganisms in the waste disposal environment, then the base inert plastic should slowly degrade and disappear. The present work focuses on the preparation of biodegradable and photodegradable blends based on low density polyethylene incorporating small quantities of ionomers as compatibilizers. The thesis consists of eight chapters. The first chapter presents an introduction to the present research work and literature survey. The details of the materials used and the experimental procedures undertaken for the study are described in the second chapter. Preparation and characterization of low density polyethylene (LDPE)-biopolymer (starch/dextrin) blends are described in the third chapter. The result of investigations on the effect of polyethylene-co-methacrylic acid ionomers on the compatibility of LDPE and starch are reported in chapter 4. Chapter 5 has been divided into two parts. The first part deals with the effect of metal oxides on the photodegradation of LDPE. The second part describes the function of metal stearates on the photodegradation of LDPE. The results of the investigations on the role of various metal oxides as pro-oxidants on the degradation of ionomer compatibilized LDPE-starch blends are reported in chapter 6. Chapter 7 deals with the results of investigations on the role of various metal stearates as pro-oxidants on the degradation of ionomer compatibilized LDPE-starch blends. The conclusion of the investigations is presented in the last chapter of the thesis.

Assessment of trophic change and its probable impact on tropical estuarine environment (the Kodungallur-Azhikode estuary, India)

The cumulative effects of global change, including climate change, increased population density and domestic waste disposal, effluent discharges from industrial processes, agriculture and aquaculture will likely continue and increases the process of eutrophication in estuarine environments. Eutrophication is one of the leading causes of degraded water quality, water column hypoxia/anoxia, harmful algal bloom (HAB) and loss of habitat and species diversity in the estuarine environment. The present study attempts to characterize the trophic condition of coastal estuary using a simple tool; trophic index (TRIX) based on a linear combination of the log of four state variables with supplementary index Efficiency Coefficient (Eff. Coeff.) as a discriminating tool. Numerically, the index TRIX is scaled from 0 to10, covering a wide range of trophic conditions from oligotrophic to eutrophic. Study area Kodungallur-Azhikode Estuary (KAE) was comparatively shallow in nature with average depth of 3.6±0.2 m. Dissolve oxygen regime in the water column was ranged from 4.7±1.3 mgL−1 in Station I to 5.9±1.4 mgL−1 in Station IV. The average nitrate-nitrogen (NO3-N) of KAE water was 470 mg m−3; values ranged from Av. 364.4 mg m−3 at Station II to Av. 626.6 mg m−3at Station VII. The mean ammonium-nitrogen (NH4 +-N) varied from 54.1 mg m−3 at Station VII to 101 mg m−3 at Station III. The average Chl-a for the seven stations of KAE was 6.42±3.91 mg m−3. Comparisons over different spatial and temporal scales in the KAE and study observed that, estuary experiencing high productivity by the influence of high degree of eutrophication; an annual average of 6.91 TRIX was noticed in the KAE and seasonal highest was observed during pre monsoon period (7.15) and lowest during post monsoon period (6.51). In the spatial scale station V showed high value 7.37 and comparatively low values in the station VI (6.93) and station VII (6.96) and which indicates eutrophication was predominant in land cover area with comparatively high water residence time. Eff. Coeff. values in the KAE ranges from −2.74 during monsoon period to the lowest of −1.98 in pre monsoon period. Present study revealed that trophic state of the estuary under severe stress and the restriction of autochthonous and allochthonous nutrient loading should be keystone in mitigate from eutrophication process

Effect of vanadia on physico-chemical and catalytic characteristics of dysprosia

Physico-chemical characterization of DY203/V2O5 systems prepared through wet impregnation method has been carried out using various techniques like EDX, XRD, FTIR. thermal studies, BET surface area, pore volume and pore size distribution analysis. The amount of vanadia incorporated has been found to influence the surface properties of dysprosia. The spectroscopic results combining with X-ray analysis reveal that vanadia species exist predominantly as isolated amorphous vanadyl units along with crystalline dysprosium orthovanadate. Basicity studies have been conducted by adsorption of electron acceptors and acidity and acid strength distribution by temperature programmed desorption of ammonia. Cyclohexanol decomposition has been employed as a chemical probe reaction to examine the effect of vanadia on the acid base property of Dy2O3. Incorporation of vanadia titrates thc Lewis acid and base sites of Dy2O3, while an enhancement of Bronsted acid sites has been noticed. Data have been correlated with the catalytic activity of these oxides towards the vapour phase methylation of phenol

Novel Low Loss A(A1/4 B2/4 C1/4)O3 Dielectrics and Their Applications In Broadband Antennas

This thesis presents the microwave dielectric properties of two novel dielectric resonator materials with the composition Ca(Ca1/4Nb2/4Ti1/4)O3 and Ca(Ca1/4Ta2/4Ti1/4)O3 ceramics and their application in the fabrication of wideband antennas. The microwave dielectric properties of the ceramics were tailored by several techniques such as doping, glass addition and solid solution formations in the complex perovskite A and B-sites with suitable substitutions. Among the wide variety of DRs developed, ceramic resonators with optimum properties were identified to fabricate broadband dielectric resonator loaded microstrip patch antennas. Furthermore, wideband, high permittivity dielectric resonator antennas were fabricated and explored the possibility of tuning their characteristics by modifying the feed line geometries.

Fish Driven Bioturbation as a Viable Aquaculture Technology for Increasing Production and Improving Ecological Sustainability of Giant Tiger Shrimp Penaeus Monodon (FABRlClUS)

A general introduction to the problems faced in the shrimp culture due to waste formation and its consequent environmental hazards and production problems of Giant tiger shrimp, Penaeus monodon is highlighted by the author in this thesis. The objective of the present work was to assess the potential of brackish water finfish to improve bottom soil conditions and thereby increase the growth and production of Penaeus monodon. The salient findings of the present study are summarized in chapter 7. This is followed by the references cited in the thesis and list ofpublications originated from the present study.

Physiology of the blood of cat fishes

The vast areas of derelict swamps covered by macrophyton and swarmed by insects scattered in different parts of India are at present either under total negligence or utilized as waste disposal dumps. Eventhough Indian subcontinent is ranked among the first ten fish producing countries in the world, the fish production is not at par with the increasing need of protein in the average Indian diet. So the water areas which become unusable for conventional human activities like the swamps could be used for fish culture which would increase the availability of protein in the form of fish flesh, thus providing new opportunities to the fishermen. But the conversion of swamps for fish culture would entail considerable expenditure. Hence the significance of a group of fresh water fishes which have made their favourable abode the muddy swamps of tropics depending partly on accessory _respiration to survive in the inimical environment. The homeostasis achieved in such a hostile, hypoxic medium make them excellent choices for culture in the derelict freshwater bodies of India. These air breathing fishes form an economically important group which are highly esteemed as food fishes in many parts of South Asia and Africa. Though their natural habitat seems to be the marshes, they have also conquered other freshwater bodies like ponds, tanks, rivers and flooded paddy fields. They can also tolerate slightly brackish waters. They are known for their nutritive, invigorating and therapeutic qualities and are recommended by physicians as diet during convalescence (Jhingran, 1982)

Influence Of Additives On The Drain Down Characteristics Of Stone Matrix Asphalt Mixtures

In Kerala highways, where traditional dense graded mixtures are used for the surface courses, major distress is due to moisture induced damages. Development of stabilized Stone Matrix Asphalt (SMA) mixtures for improved pavement performance has been the focus of research all over the world for the past few decades. Many successful attempts are made to stabilize SMA mixtures with synthetic fibres and polymers. India, being an agricultural economy produces fairly huge quantity of natural fibres such as coconut, sisal, banana, sugar cane, jute etc.. Now- a -days the disposal of waste plastics is a major concern for an eco- friendly sustainable environment. This paper focuses on the influence of additives like coir, sisal, banana fibres (natural fibres), waste plastics (waste material) and polypropylene (polymer) on the drain down characteristics of SMA mixtures. A preliminary investigation is conducted to characterize the materials used in this study. Drain down sensitivity tests are conducted to study the bleeding phenomena and drain down of SMA mixtures. Based on the drain down characteristics of the various stabilized mixtures it is inferred that the optimum fibre content is 0.3% by weight of mixture for all fibre mixtures irrespective of the type of fibre. For waste plastics and polypropylene stabilized SMA mixtures, the optimum additive contents are respectively 7% and 5% by weight of mixture. Due to the absorptive nature of fibres, fibre stabilizers are found to be more effective in reducing the drain down of the SMA mixture. The drain values for the waste plastics mix is within the required specification range. The coir fibre additive is the best among the fibres investigated. Sisal and banana fibre mixtures showed almost the same characteristics on stabilization.

Characterization and FTIR spectral studies of human urinary stones from Southern India

Urinary stones resected from urinary bladders of patients hailing from Kollam district of Kerala State, India were analyzed by SEM, XRD and by thermal analysis techniques. The analytical results indicate that, stones have different composition, i.e., calcium phosphate, calcium phosphate hydroxide and sodium calcium carbonate. Infrared spectral studies also reveal the presence of phosphates or carbonates in these samples. Further, IR spectral investigations have revealed that amorphous carbonated species are occupied in PO4 sites in calcium phosphate type stone and OH sites in calcium phosphate hydroxide sample. Thermal studies of these samples also reveal that, carbon dioxide is released from carbonated samples upon heating which is related to amount of carbon content and bond strength. Crystals with defects and irregular morphology are grown inside the urinary bladder due to variation in crystal growth conditions

Assessment of Energy Conservation in Indian Cement Industry and Forecasting of Co2 Emissions

Cement industry ranks 2nd in energy consumption among the industries in India. It is one of the major emitter of CO2, due to combustion of fossil fuel and calcination process. As the huge amount of CO2 emissions cause severe environment problems, the efficient and effective utilization of energy is a major concern in Indian cement industry. The main objective of the research work is to assess the energy cosumption and energy conservation of the Indian cement industry and to predict future trends in cement production and reduction of CO2 emissions. In order to achieve this objective, a detailed energy and exergy analysis of a typical cement plant in Kerala was carried out. The data on fuel usage, electricity consumption, amount of clinker and cement production were also collected from a few selected cement industries in India for the period 2001 - 2010 and the CO2 emissions were estimated. A complete decomposition method was used for the analysis of change in CO2 emissions during the period 2001 - 2010 by categorising the cement industries according to the specific thermal energy consumption. A basic forecasting model for the cement production trend was developed by using the system dynamic approach and the model was validated with the data collected from the selected cement industries. The cement production and CO2 emissions from the industries were also predicted with the base year as 2010. The sensitivity analysis of the forecasting model was conducted and found satisfactory. The model was then modified for the total cement production in India to predict the cement production and CO2 emissions for the next 21 years under three different scenarios. The parmeters that influence CO2 emissions like population and GDP growth rate, demand of cement and its production, clinker consumption and energy utilization are incorporated in these scenarios. The existing growth rate of the population and cement production in the year 2010 were used in the baseline scenario. In the scenario-1 (S1) the growth rate of population was assumed to be gradually decreasing and finally reach zero by the year 2030, while in scenario-2 (S2) a faster decline in the growth rate was assumed such that zero growth rate is achieved in the year 2020. The mitigation strategiesfor the reduction of CO2 emissions from the cement production were identified and analyzed in the energy management scenarioThe energy and exergy analysis of the raw mill of the cement plant revealed that the exergy utilization was worse than energy utilization. The energy analysis of the kiln system showed that around 38% of heat energy is wasted through exhaust gases of the preheater and cooler of the kiln sysetm. This could be recovered by the waste heat recovery system. A secondary insulation shell was also recommended for the kiln in the plant in order to prevent heat loss and enhance the efficiency of the plant. The decomposition analysis of the change in CO2 emissions during 2001- 2010 showed that the activity effect was the main factor for CO2 emissions for the cement industries since it is directly dependent on economic growth of the country. The forecasting model showed that 15.22% and 29.44% of CO2 emissions reduction can be achieved by the year 2030 in scenario- (S1) and scenario-2 (S2) respectively. In analysing the energy management scenario, it was assumed that 25% of electrical energy supply to the cement plants is replaced by renewable energy. The analysis revealed that the recovery of waste heat and the use of renewable energy could lead to decline in CO2 emissions 7.1% for baseline scenario, 10.9 % in scenario-1 (S1) and 11.16% in scenario-2 (S2) in 2030. The combined scenario considering population stabilization by the year 2020, 25% of contribution from renewable energy sources of the cement industry and 38% thermal energy from the waste heat streams shows that CO2 emissions from Indian cement industry could be reduced by nearly 37% in the year 2030. This would reduce a substantial level of greenhouse gas load to the environment. The cement industry will remain one of the critical sectors for India to meet its CO2 emissions reduction target. India’s cement production will continue to grow in the near future due to its GDP growth. The control of population, improvement in plant efficiency and use of renewable energy are the important options for the mitigation of CO2 emissions from Indian cement industries