STUDIES ON THE CELL STRUCTURE AND MECHANICAL PROPERTIES OF NR/LATEX RECLAIM/HSR BASED MICROCELLULAR SHEETS

In natural rubber/high styrene resin microcellular sheets, part of natural rubber was replaced by latex reclaim prepared from waste latex products. The mechanical properties and cell structure of the products were evaluated. It was found that latex reclaim can replace about 30% of natural rubber without affecting the technical properties of the microcellular sheets.

Marine bacterial prodigiosin as dye for rubber latex, polymethyl methacrylate sheets and paper

Prodigiosin is known for its immunomodulatory, antibacterial, antimycotic, antimalarial, algicidal and anticancer activities. Here, we reported the evaluation of prodigiosin pigment as a dyeing agent in rubber latex, paper and polymethyl methacrylate (PMMA) so that it can be considered as an alternative to synthetic pigments. Maximum color shade was obtained in rubber sheet prepared with 0.5 parts per hundred gram of rubber (phr) pigment and PMMA sheet incorporated with 0.08 μg pigment. Results indicate scope for utilization of prodigiosin as dye for PMMA and rubber and also prodigiosin dyed paper as a pH indicator. Further, being a natural and water insoluble pigment, it is ecofriendly

A Novel Accelerator Combination for the Low Temperature Curing of Silica-Filled NBR Compounds

Zinc salts of ethyl, isopropyl, and butyl xanthates were prepared in the laboratory. The effect of these xanthates in combination with zinc diethyldithiocarbamate (ZDC) on the vulcanization of silica-filled NBR compounds has been studied at different temperatures. The cure times of these compounds were compared with that of NBR compounds containing tetramethylthiuram disulphide/dibenzthiazyl disulphide. The rubber compounds with the xanthates and ZDC were cured at various temperatures from 60 to 150°C. The sheets were molded and properties such as tensile strength, tear strength, crosslink density, elongation at break, compression set, abrasion resistance, flex resistance, heat buildup, etc. were evaluated. The properties showed that zinc salt of xanthate/ZDC combination has a positive synergistic effect on the cure rate and mechanical properties of NBR compounds.

Low Temperature Curing of NBR for Property Improvement

Zinc salts of ethyl, isopropyl, and butyl xanthates are prepared in the laboratory, and the effect of these xanthates with zinc diethyl dithiocarbamate (ZDC) on the vulcanization of HAF-filled nitrile butadiene rubber (NBR) compounds has been studied at different temperatures. The cure times of these compounds have been compared with that of NBR compounds containing TMTD/MBTS. The rubber compounds with the three xanthate accelerators and ZDC are cured at various temperatures from 60 to 150°C. The sheets are molded and properties such as tensile strength, tear strength, cross-link density, elongation at break, compression set, abrasion resistance, flex resistance, etc. have been evaluated. The properties show that zinc salt of the xanthate/ZDC accelerator system has a positive synergistic effect on the cure rate and mechanical properties of NBR compounds.

Studies on Xanthate/Dithiocarbamate Accelerator Combination in NR/BR Blends

Zinc butyl xanthate [Zn(bxt)2] was prepared in the laboratory . The effect of this xanthate with zinc diethyl dithiocarbamate (ZDC) on the vulcanization of natural rubber ( NR), polybutadiene rubber (BR), and NR/BR blend has been studied at different temperatures. The amounts of Zn (bxt)2 and ZDC in the compounds were optimized by varying the amount of ZDC from 0 . 75 to 1.5 phr and Zn (bxt)2 from 0 . 75 to 1 .5 phr. The cure characteristics were also studied . HAF filled NR, BR, and NR / BR blend compounds were cured at different temperatures from 60 to 150 C. The sheets were molded and properties such as tensile strength, tear strength, crosslink density and elongation at break, compression set, abrasion resistance, etc. were evaluated. The results show that the mechanical properties of 80NR/20BR blends are closer to that of NR vulcanizates, properties of 60NR/40BR blends are closer to BR vulcanizates, while the 70NR/30BR blends show an intermediate property.

Synergism of Xanthate/Dithiocarbamate Accelerator in Carbon Black Filled NR Compounds

Zinc salts of ethyl, isopropyl and butyl xanthates were prepared in the laboratory. The effect of these xanthates with zinc diethyldithiocarbamate (ZDC) on the vulcanization of HAF filled NR compound has been studied at different temperatures. The rubber compounds with the three xanthate accelerators and ZDC were cured at various temperatures from 60°C to 150°C. The sheets were moulded and properties such as tensile strength , tear strength , cross-link density, elongation -at-break, compression set, heat build up, abrasion resistance, flex resistance , etc. were evaluated . The properties showed that zinc xanthate/ZDC accelerator combination has a positive synergistic effect on the mechanical properties of NR compounds. The curing of HAF filled NR compound containing zinc xanthate /ZDC is slightly slower than the curing of the corresponding gum compounds . It is observed that, by gradually increasing the amount of the accelerator, the cure time of black filled NR compound can be made equal to that of the gum compou

Effect of Feeding Rate on Plastic Extrudates

Selected grades of low density polyethylene (LDPE) polystyrene (PS) were extruded in a laboratory extruder by varying the feeding rate at different revolutions per minute and temperatures. The mechanical properties of the extruded plastic sheets were determined. LDPE shows a marked variation in mechanical properties with feeding rate while PS shows a marginal change in mechanical properties with feeding rate. However, for both plastics there is a particular feeding rate in the starved region which results in maximum mechanical properties.

Development of Polybutadiene (BR)-Polyethylene (LDPE) Blend Based Microcellular Soles for Low-Temperature Applications

Microcellular (MC) soles based on polybutadiene (BR) and low-density polyethylene (LDPE) blends for low-temperature applications were developed. A part of BR in BR-LDPE blend was replaced by natural rubber (NR) for property improvement. The BR-NR-LDPE blend-based MC sole shows good technical properties. Sulphur curing and DCP curing were tried in BR-LDPE and NR-BR-LDPE blends. Study shows that sulphur-cured MC sheets possess better technical properties than DCPcured MC sheets. 90/10 BR-LDPE and 60/30/10 BR-NR-LDPE blend combinations are found to be suitable for low-temperature applications.

Rice Hull Ash as Filler in Microcellular Soles

Fully burnt rice hull (rice hull ash) was tried as a low cost filler in place of precipitated silica in NBR/PVC based microcellular soles. The mechanical properties of the soles containing silica and ash are found to be comparable. The expansion is marginally higher in the presence of ash, which permits to reduce the amount of blowing agent. Cell structure of microcellular sheets remains unchanged when silica is replaced by ash.

Xanthate Accelerators for Low Temperature Curing of Natural Rubber

ABSTRACT: Zinc salts of ethyl, isopropyl, and butyl xanthates were prepared in the laboratory. They were purified by reprecipitation and were characterized by IR, NMR, and thermogravimetric analysis techniques. The melting points were also determined. The rubber compounds with different xanthate accelerators were cured at temperatures from 30 to 150°C. The sheets were molded and properties such as tensile strength, tear strength, crosslink density, elongation at break, and modulus at 300% elongation were evaluated. The properties showed that all three xanthate accelerators are effective for room temperature curing.

Spatio-Temporal Changes in the Wetland Ecosystem of Cochin City using Remote Sensing and GIS

Urban developments have exerted immense pressure on wetlands. Urban areas are normally centers of commercial activity and continue to attract migrants in large numbers in search of employment from different areas. As a result, habitations keep coming up in the natural areas / flood plains. This is happening in various Indian cities and towns and large habitations are coming up in low-lying areas, often encroaching even over drainage channels. In some cases, houses are constructed even on top of nallahs and drains. In the case of Kochi the situation is even worse as the base of the urban development itself stands on a completely reclaimed island. Also the topography and geology demanded more reclamation of land when the city developed as an agglomerative cluster. Cochin is a coastal settlement interspersed with a large backwater system and fringed on the eastern side by laterite-capped low hills from which a number of streams drain into the backwater system. The ridge line of the eastern low hills provides a welldefined watershed delimiting Cochin basin which help to confine the environmental parameters within a physical limit. This leads to an obvious conclusion that if physiography alone is considered, the western flatland is ideal for urban development. However it will result in serious environmental deterioration, as it comprises mainly of wetland and for availability of land there has to be large scale filling up of these wetlands which includes shallow mangrove-fringed water sheets, paddy fields, Pokkali fields, estuary etc.Chapter 1 School 4 of Environmental Studies The urban boundaries of Cochin are expanding fast with a consequent over-stretching of the existing fabric of basic amenities and services. Urbanisation leads to the transformation of agricultural land into built-up areas with the concomitant problems regarding water supply, drainage, garbage and sewage disposal etc. Many of the environmental problems of Cochin are hydrologic in origin; like water-logging / floods, sedimentation and pollution in the water bodies as well as shoreline erosion

Molecular Characterisation and Phylogenetic Analysis of a Novel Isoform of Hepatic Antimicrobial Peptide, Hepcidin (Zc-hepc1), from the Coral Fish Moorish idol, Zanclus cornutus (Linnaeus,1758)

Hepcidin is a family of short cysteine-rich antimicrobial peptides (AMPs) participating in various physiological functions with inevitable role in host immune responses. Present study deals with identification and characterisation of a novel hepcidin isoform from coral fish Zanclus cornutus. The 81 amino acid (aa) preprohepcidin obtained from Z. cornutus consists of a hydrophobic aa rich 22 mer signal peptide, a highly variable proregion of 35 aa and a bioactive mature peptide with 8 conserved cysteine residues which contribute to the disulphide back bone. The mature hepcidin, Zc-hepc1 has a theoretical isoelectric point of 7.46, a predicted molecular weight of 2.43 kDa and a net positive charge of ?1. Phylogenetic analysis grouped Z. cornutus hepcidin with HAMP2 group hepcidins confirming the divergent evolution of hepcidin-like peptide in fishes. Zc-hepc1 can attain a b-hairpin-like structure with two antiparallel b-sheets. This is the first report of an AMP from the coral fish Z. cornutus.

Ecological studies of the Parambikulam Tiger Reserve in the Western Ghats of India, using Remote Sensing and GIS

mbikulam Tiger Reserve of Western Ghats using Geospatial technology. The major objectives of the study are Land use land cover mapping (LULC) and Phytodiversity analysis. Satellite data was used to map the land use / land cover using supervised classification techniques in Erdas imagine. The change for a period of 32 years was assessed using the multi-temporal satellite datasets from Landsat MSS (1973), Landsat TM (1990), and IRS P6 LISS III (2005). A geospatial approach was used for the land cover analysis. Digital elevation models, Satellite imageries and SOI topo sheets were the data sets used in the analysis. Vegetation sampling plots distributed over the different forest types were enumerated and studied for Phytodiversity analysis.

Performance Assessment of Sandwich Structures with Debonds and Dents

A sandwich construction is a special form of the laminated composite consisting of light weight core, sandwiched between two stiff thin face sheets. Due to high stiffness to weight ratio, sandwich construction is widely adopted in aerospace industries. As a process dependent bonded structure, the most severe defects associated with sandwich construction are debond (skin core bond failure) and dent (locally deformed skin associated with core crushing). Reasons for debond may be attributed to initial manufacturing flaws or in service loads and dent can be caused by tool drops or impacts by foreign objects. This paper presents an evaluation on the performance of honeycomb sandwich cantilever beam with the presence of debond or dent, using layered finite element models. Dent is idealized by accounting core crushing in the core thickness along with the eccentricity of the skin. Debond is idealized using multilaminate modeling at debond location with contact element between the laminates. Vibration and buckling behavior of metallic honeycomb sandwich beam with and without damage are carried out. Buckling load factor, natural frequency, mode shape and modal strain energy are evaluated using finite element package ANSYS 13.0. Study shows that debond affect the performance of the structure more severely than dent. Reduction in the fundamental frequencies due to the presence of dent or debond is not significant for the case considered. But the debond reduces the buckling load factor significantly. Dent of size 8-20% of core thickness shows 13% reduction in buckling load capacity of the sandwich column. But debond of the same size reduced the buckling load capacity by about 90%. This underscores the importance of detecting these damages in the initiation level itself to avoid catastrophic failures. Influence of the damages on fundamental frequencies, mode shape and modal strain energy are examined. Effectiveness of these parameters as a damage detection tool for sandwich structure is also assessed