32 resultados para School of composition

em Cochin University of Science


Relevância:

100.00% 100.00%

Publicador:

Resumo:

With the stabilization of world finfish catches in general, and the depletion of a number of fish stocks that used to support industrial-scale fisheries, increasing attention is now being paid, to the so-called unconventional marine resources, which include many species of cephalopods. One of such important cephalopod resource is the tropical Indo-Pacific pelagic oceanic squid Sthenoteuthis oualaniensis. It is the most abundant large sized squid in the Indo- Pacific region with an estimated biomass of 8-11 metric tons. However, its distribution, biology, life cycle and nutrient value in the south west coast of India are still poorly known. So any new information of this species in the waters off the south west coast of India has important scientific significance for effective and rational utilization of this Oceanic fishery resources, especially during the time of depletion of shallow water resources. In view of that this study investigated different aspects of the Sthenoteuthis oualaniensis, such as morphometry, growth, mortality, maturation, spawning, food, feeding and biochemical composition in the south west coast of India to understand its possible prospective importance for commercial fishing and management of its fishery

Relevância:

100.00% 100.00%

Publicador:

Resumo:

The present work deals with the texture, mineralogy and geochemistry of bedload sediments of the main stream of the Chaliyar basin, a typical small drainage system of the tropics enjoying heavy rain fall and moderate climate, located essentially in the Northern Kerala and flowing over the crystalline rocks (and their laterized duricrust) of the South Indian granulite terrain. As the Chaliyar is the major river draining the Wynad Gold Fields and is known for its placer gold occurrences, the thesis gives special emphasize on understanding the nature and distribution of detrital gold in sediments of the basin, while attempting to infer the provenance characteristics and factors involved in the evolution of sediments in general. Minerologically the chaliyar basin sands are quartzose. The quartz and feldspar contents in the coarse sand fraction of the basin range from 64 to 86% and 2 to 16% respectively. The Q/F ration ranges from 4 to 38 with a slight decrease in the lower reaches. Other minerals present include, hornblende, pyroxene and heavy minerals like opaques, garnet, rutile, biotite, spene, silliminite, zircon, apatite and monazite some of which are seen as inclusions in quartz. The major element composition of Chaliyar bedload sediments in the main channel and the headwater tributaries is related to the mineralogical and textual characteristics of sediments.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

The work was carried out with an objective to know the quantitative and qualitative nature of the macrobenthos in relation to the existing hydrographical parameters and sediment characteristics. With the above two cruises were conducted to collect materials. Representative samples were collected from each degree square of the western continental shelf. The study deals with the hydrographic parameters. The bottom water temperature, salinity and dissolved oxygen were measured. The findings showed variations according to depth and latitude. The study gives the details of sediment characteristics of the study area. 7 different types of substrata were noticed. It also explains the macro faunal composition and diversity, and the standing stock of macrobenthos. The wet-weight and numerical abundance of macrobenthic groups are included. The thesis discusses the relation between hydrography and macrobenthos, and sediment characteristics and macrobenthos, based on the results obtained by statistical analysis of the data. It also investigates the relation between macrobenthos and fishery.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

The spectral and nonlinear optical characteristics of nano ZnO and its composites are investigated. The fluorescence behaviour of nano colloids of ZnO has been studied as a function of the excitation wavelength and there is a red shift in emission peak with excitation wavelength. Apart from the observation of the reported ultra violet and green emissions, our results reveal that additional blue emissions at 420 nm and 490 nm are developed with increasing particle size. Systematic studies on nano ZnO have indicated the presence of luminescence due to excitonic emissions when excited with 255 nm as well as significant contribution from surface defect states when excited with 325 nm. In the weak confinement regime, the third-order optical susceptibility χ(3) increases with increasing particle size (R) and annealing temperature (T) and a R2 and T2.5 dependence of χ(3) is obtained for nano ZnO. ZnO nanocolloids exhibit induced absorption whereas the self assembled films of ZnO exhibit saturable absorption due to saturation of linear absorption of ZnO defect states and electronic effects. ZnO nanocomposites exhibit negative nonlinear index of refraction which can be attributed to two photon absorption followed by weak free carrier absorption. The increase of the third-order nonlinearity in the composites can be attributed to the enhancement of exciton oscillator strength. The nonlinear response of ZnO nanocomposites is wavelength dependent and switching from induced absorption to saturable absorption has been observed at resonant wavelengths. Such a change-over is related to the interplay of plasmon/exciton band bleach and optical limiting mechanisms. This study is important in identifying the spectral range and the composition over which the nonlinear material acts as an optical limiter. ZnO based nanocomposites are potential materials for enhanced and tunable light emission and for the development of nonlinear optical devices with a relatively small optical limiting threshold.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

The spectral and nonlinear optical properties of ZnO based nanocomposites prepared by colloidal chemical synthesis are investigated. Very strong UV emissions are observed from ZnO–Ag, ZnO– Cu and ZnO–SiO2 nanocomposites. The strongest visible emission of a typical ZnO–Cu nanocomposite is over ten times stronger than that of pure Cu due to transition from deep donor level to the copper induced level. The optical band gap of ZnO–CdS and ZnO–TiO2 nanocomposites is tunable and emission peaks changes almost in proportion to changes in band gap. Nonlinear optical response of these nanocomposites is studied using nanosecond laser pulses from a tunable laser in the wavelength range of 450–650 nm at resonance and off-resonance wavelengths. The nonlinear response is wavelength dependent and switching from RSA to SA has been observed at resonant wavelengths. Such a change-over is related to the interplay of plasmon/exciton band bleach and optical limiting mechanisms. The observed nonlinear absorption is explained through two photon absorption followed by weak free carrier absoption, interband absorption and nonlinear scattering mechanisms. The nonlinearity of the silica colloid is low and its nonlinear response can be improved by making composites with ZnO and ZnO–TiO2. The increase of the third-order nonlinearity in the composites can be attributed to the enhancement of exciton oscillator strength. This study is important in identifying the spectral range and the composition over which the nonlinear material acts as an RSA based optical limiter. These nanocomposites can be used as optical limiters and are potential materials for the light emission and for the development of nonlinear optical devices with a relatively small limiting threshold.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

The spectral and nonlinear optical properties of ZnO based nanocomposites prepared by colloidal chemical synthesis are investigated. Very strong UV emissions are observed from ZnO–Ag, ZnO– Cu and ZnO–SiO2 nanocomposites. The strongest visible emission of a typical ZnO–Cu nanocomposite is over ten times stronger than that of pure Cu due to transition from deep donor level to the copper induced level. The optical band gap of ZnO–CdS and ZnO–TiO2 nanocomposites is tunable and emission peaks changes almost in proportion to changes in band gap. Nonlinear optical response of these nanocomposites is studied using nanosecond laser pulses from a tunable laser in the wavelength range of 450–650 nm at resonance and off-resonance wavelengths. The nonlinear response is wavelength dependent and switching from RSA to SA has been observed at resonant wavelengths. Such a change-over is related to the interplay of plasmon/exciton band bleach and optical limiting mechanisms. The observed nonlinear absorption is explained through two photon absorption followed by weak free carrier absoption, interband absorption and nonlinear scattering mechanisms. The nonlinearity of the silica colloid is low and its nonlinear response can be improved by making composites with ZnO and ZnO–TiO2. The increase of the third-order nonlinearity in the composites can be attributed to the enhancement of exciton oscillator strength. This study is important in identifying the spectral range and the composition over which the nonlinear material acts as an RSA based optical limiter. These nanocomposites can be used as optical limiters and are potential materials for the light emission and for the development of nonlinear optical devices with a relatively small limiting threshold.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

School of Marine Sciences, Cochin University of Science and Technology

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Division of Marine Biology, Microbiology and Biochemistry, School of Marine Sciences, Cochin University of Science and Technology

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Division of Marine Biology, Microbiology and Biochemistry, School of Marine Sciences, Cochin University of Science and Technology

Relevância:

100.00% 100.00%

Publicador:

Resumo:

School of Industrial Fisheries, Cochin University of Science and Technology

Relevância:

100.00% 100.00%

Publicador:

Resumo:

The present study focused on the quality of rainwater at various land use locations and its variations on interaction with various domestic rainwater harvesting systems.Sampling sites were selected based upon the land use pattern of the locations and were classified as rural, urban, industrial and sub urban. Rainwater samples were collected from the south west monsoon of May 2007 to north east monsoon of October 2008, from four sampling sites namely Kothamangalam, Emakulam, Eloor and Kalamassery, in Ernakulam district of the State of Kerala, which characterized typical rural, urban, industrial and suburban locations respectively. Rain water samples at various stages of harvesting were also collected. The samples were analyzed according to standard procedures and their physico-chemical and microbiological parameters were determined. The variations of the chemical composition of the rainwater collected were studied using statistical methods. It was observed that 17.5%, 30%, 45.8% and 12.1% of rainwater samples collected at rural, urban, industrial and suburban locations respectively had pH less than 5.6, which is considered as the pH of cloud water at equilibrium with atmospheric CO,.Nearly 46% of the rainwater samples were in acidic range in the industrial location while it was only 17% in the rural location. Multivariate statistical analysls was done using Principal Component Analysis, and the sources that inf1uence the composition of rainwater at each locations were identified .which clearly indicated that the quality of rain water is site specific and represents the atmospheric characteristics of the free fall The quality of harvested rainwater showed significant variations at different stages of harvesting due to deposition of dust from the roof catchment surface, leaching of cement constituents etc. Except the micro biological quality, the harvested rainwater satisfied the Indian Standard guide lines for drinking water. Studies conducted on the leaching of cement constituents in water concluded that tanks made with ordinary portland cement and portland pozzolana cement could be safely used for storage of rain water.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Investigations on the fracture behaviour of polymer blends is the topic of this thesis. The blends selected are PP/HDPE and PS/HIPS. PP/HDPE blend is chosen due to its commercial importance and PS/HIPS blend is selected to study the transition from brittle fracture to ductile fracture.PP/HDPE blends were prepared at different compositions by melt blending at 180°C and fracture failure process was investigated by conducting notch sensitivity test and tensile test at different strain rates. The effects of two types of modifiers (particulate and elastomer) on the fracture behaviour and notch sensitivity of PP/HDPE blends were studied. The modifiers used are calcium carbonate, a hard particulate filler commonly used in plastics and Ethylene Propylene Diene Monomer (EPDM). They were added in 2%, 4% and 6% by weight of the blends.The study shows that the mechanical properties of PP/HDPE blends can be optimized by selecting proper blend compositions. The selected modifiers are found to alter and improve the fracture behaviour and notch sensitivity of the blends. Particulate fillers like calcium carbonate can be used for making the mechanical behaviour more stable at the various blend compositions. The resistance to notch sensitivity of the blends is found to be marginally lower in the presence of calcium carbonate. The elastomeric modifier EPDM produces a better stability of the mechanical behaviour. A low concentration of EPDM is sufficient to effect such a change. EPDM significantly improves the resistance to notch sensitivity of the blends. The study shows that judicious selection of modifiers can improve the fracture behaviour and notch sensitivity of PP/HDPE blends and help these materials to be used for critical applications.For investigating the transition in fracture behaviour and failure modes, PS/HIPS blends were selected. The blends were prepared by melt mixing followed by injection moulding to prepare the specimens for conducting tensile, impact and flexure tests. These tests were used to simulate the various conditions which promote failure.The tensile behaviour of unnotched and notched PS/HIPS blend samples were evaluated at slow speeds. Tensile strengths and moduli were found to increase at the higher testing speed for all the blend combinations whereas maximum strain at break was found to decrease. For a particular speed of testing, the tensile strength and modulus show only a very slight decrease as HIPS content is increased up to about 40%. However, there is a drastic decrease on increasing the HIPS content thereafter.The maximum strain at break shows only a very slight change up to about 40% HIPS content and thereafter shows a remarkable increase. The notched specimens also follow a comparable trend even though the notch sensitivity is seen high for PS rich blends containing up to 40% HIPS. The notch sensitivity marginally decreases with increase in HIPS content. At the same time, it is found to increase with the increase in strain rate. It is observed that blends containing more than 40% HIPS fail in ductile mode.The impact characteristics of PSIHIPS blends studied were impact strength, the energy absorbed by the test specimen and impact toughness. Remarkable increase in impact strength is observed as HIPS content in the blend exceeds 40%. The energy absorbed by the test specimens and the impact toughness also show a comparable trend.Flexural testing which helps to characterize the load bearing capacity was conducted on PS/HIPS blend samples at the two different testing speeds of 5mmlmin and 10 mm/min. The flexural strength increases with increase in testing speed for all the blend compositions. At both the speeds, remarkable reduction in flexural strength is observed as HIPS content in the blend exceeds 40%. The flexural strain and flexural energy absorbed by the specimens are found to increase with increase in HIPS content. At both the testing speeds, brittle fracture is observed for PS rich blends whereas HIPS rich blends show ductile mode of failure.Photoelastic investigations were conducted on PS/HIPS blend samples to analyze their failure modes. A plane polariscope with a broad source of light was utilized for the study. The coloured isochromatic fringes formed indicate the presence of residual stress concentration in the blend samples. The coverage made by the fringes on the test specimens varies with the blend composition and it shows a reducing trend with the increase in HIPS content. This indicates that the presence of residual stress is a contributing factor leading to brittle fracture in PS rich blends and this tendency gradually falls with increase in HIPS content and leads to their ductile mode of failure.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

In the present study two aspects of cephalopod fishery such as (i) landings and (ii) utilization including export of cephalopods from Indian are dealt with. Under the topic landings, craft, both traditional and mechanized and fishing techniques employed for capturing cephalopods are discussed. General trend in cephalopod landing in India and particularly south west coast, species composition, description and geographic distribution of important species of cuttle fishes, squids and octopus and the distribution and abundance of cephalopods along the continental shelf of the south west coast are also discussed. Some biological aspects like population parameters, maturation and spawning, food and feeding of the two representive species of cuttle fishes and squid viz, Sepia pharaonis and Loligo duvauceli are studied.Under utilization, general handling and processing of various frozen cephalopods products for exports and commercial operation in a typical plant are studied. The export of cephalopod products since its commencement is studied in detail and market strategy for enhancing the export are suggested.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

This thesis Entitled macrobenthos of the continental margin (200-1000m) of south eastern arabian sea with special reference to polychaetes. The continental margins are geologically complex and hydrodynamically active regions of the ocean, where vital biogeochemical processes take place from a global perspective. The Eastern Arabian Sea is one of the most productive regions of the world, and as a result, vast amount of organic matter is supplied to the sub surface waters and sea bed of the Arabian Sea. In this study, data on faunal abundance, standing crop and faunal composition, together with sedimentary and environmental parameters were collected from three depths (200m, 500m & 1000m) in nine bathymetric transects along the South Eastern Arabian Sea (from Cape Comorin to Karwar) during three surveys. In the present study, five textural classes of sediments were identified from the SEAS margin, viz. sand, silty sand, sandy silt, clayey silt and admixture of sand, silt and clay. The composition of sand was higher in the southern region and decreased progressively towards the north. On the shelf edge and upper slope regions in the south (Cape to Kollam) in particular, sandy sediments dominated .

Relevância:

100.00% 100.00%

Publicador:

Resumo:

This thesis entitled triterpenoids as biomarkers of mangrove organic matter in cochin estuarine system.Mangrove forests, known as rainforests of the sea are one of the most important coastal ecosystems in the world in terms of primary production and coastal protection.Estuaries, the important areas of world’s coastal zones link the carbon cycle of the oceans to the continents.Three mangrove ecosystems and three estuarine stations around Cochin region, southwest coast of India were selected for the present study. The thesis is divided into five chapters. Chapter 1 is the Introduction and it deals with the aim and scope of the present study. Chapter 2 is Materials and Methods. This chapter deals with the nature and general geographical features of the study area. It also contains the details of the sampling and analytical methodology.the present study. Chapter 3 is Geochemistry and it includes the seasonal and spatial variations of the geochemical parameters in the surface sediments.Chapter 4 is Biochemical Composition. It covers the biochemical composition of organic matter in the surface sediments to examine the quality and quantity of organic matter.Chapter 5, Triterpenoid Biomarkers in Sediments, characterize the organic matter in the sediments of the mangrove and estuarine ecosystems under study, to assess the possible sources with the help of triterpenoid biomarkers along with other lipid biomarkers.