Modification of Polyethylenes by Reactive Extrusion

The main aim of the study was to optimise the reactive extrusion conditions in the conventional modification processes of polyethylenes in a single screw extruder.The optimum conditions for peroxide crosslinking of low density polyethylene (LDPE), linear low density polyethylene (LLDPE) and their blend were determined in a torque rheometer. The actual reactive extrusion was performed in a laboratory single screw extruder using the optimum parameters. The influence of the coagent, triaUyl cyanurate (TAC), on the cross linking of low density polyethylene in the presence of peroxide was also investigated. The peroxide crosslinking was found to improve the mechanical properties and the thermal stability of the polyethylenes. The efficiency of crosslinking was found to be improved by the addition of coagent such as TAC.The optimum conditions for silane grafting viz temperature, shear rate, silane and DCP concentrations were determined on a torque rheometer in the case of LDPE, LLDPE and their blend. Silane grafting of LDPE in the presence of peroxide was performed with and without addition of water. Compounding of such mixtures in the melt at high temperatures caused decomposition of the peroxide and grafting of alkoxy silyl groups to the polyethylene chains.The optimum parameters for maleic anhydride modification of LDPE, LLDPE and their blend were determined. The grafting reaction was confinned by FTIR spectroscopy. Modification of polyethylenes with maleic anhydride in the presence of dicumyl peroxide was found to be useful in improving mechanical properties. The improvement was found to be mainly due to the grafting of carboxyl group and formation of crosslinks between the chains. The cross linking initiated improvements indicate extended property profiles and new application fields for polyethylenes.On the whole the study shows that the optimum conditions for modifying polyethylenes can be determined on a torque rheometer and actual modification can be performed in a single screw extruder by employing the optimum parameters for improved mechanical! thermal behaviour without seriously affecting their processing behaviour.

Silane Grafting of Polyethylenes

Reactive extrusion is an attractive means of polymer processing since the shaping and reaction take place in a single operation. In this paper we report the silane grafting of polyethylenes in a single screw extruder. The optimum conditions for silane grafting, viz. temperature, shear rate, silane and DCP concentrations, were determined on a torque rheometer and then actual extrusion was performed using these conditions. The study shows that an optimum low level of grafting/ crosslinking can be introduced into polyethylene during its extrusion for better mechanical behavior and=or thermal stability without affecting the processability.

Starved Extrusion for the Improvement of Mechanical Properties of Rubber Vulcanizates

Filled compounds of natural rubber, isobutylene-isoprene rubber and styrene-butadiene rubber compounds were extruded through a laboratory extruder by varying the feeding rate at different temperatures and revolutions per minute. The extruded compounds were vulcanized up to their optimum cure times and the mechanical properties of the vulcanizates were determined. The properties suggest that there is a particular feeding rate in the starved fed region which results in maximum mechanical properties. The study shows that running the extruder at a slightly starved condition is an attractive means of improving the physical properties.

Significance of Feeding Rate in the Extrusion of Filled and Gum 11R Vulcanizates

Filled and gum compounds of Isobutylene-Isoprene rubber were extruded through a laboratory extruder at various feeding rates, different temperatures and revolutions per minute. The extruded compounds were vulcanized up to their optimum cure times and the mechanical properties of the vulcanizates were determined. The properties suggest that there is a particular feeding rate in the starved fed region, which results in maximum mechanical properties. The study shows that running the extruder at a slightly starved condition is an attractive means of improving the physical properties.

Reactive loaded microstrip leaky wave antenna for low cost beam steering applications

A novel fixed frequency beam scanning microstrip leaky wave antenna is reported. The beam scanning at fixed frequency is achieved by reactive loading. Simulation and measured results shows frequency scanability of 80° as well as fixed frequency beam steering of 68° over the −10 dB impedance band of 4.56–5.06 GHz.

Studies on the Solvent Dependence in the Reaction of a Few (Anthracen-9-yl)MethyLamines and Sulfanes with Reactive Acetylenes

The thesis entitled ‘Studies on the Solvent Dependence in the Reaction of a Few (Anthracen-9-yl)methylamines and Sulfanes with Reactive Acetylenes’ is divided into six chapters. ln Chapter l a general survey of electron transfer reactions, Diels-Alder reactions and Michael-type additions is presented. A detailed discussion on the synthesis of several (anthracen-9-yl)methylamines is presented in Chapter 2. In Chapter 3, results of preliminary photophysical studies on a few (anthracen-9yl) methylamines are compiled. A detailed discussion on extensive examination of dependence in the reaction of (anthracen-9-yl)methylamines with reactive acetylenes is presented Chapter 4. Details on the synthesis and reaction of a few (anthracen-9-yl)methylsulfanes with DMAD are described in Chapter 5.

Effect of Feeding Rate in Polymer Extrusion ”

Starve feeding of single screw extruder was described as an important means of improving the performance characteristics of the extruder. In addition to such improvement with versatility, the starve feeding technique also may affect the mechanical properties of the extrudate since the heat transfer an(l mixing characteristics in the starve fed and Hood fed extruders are not the same. Since the material is more loosely packed in the channels of the starve fed extruder, there may be greater bed mobility and uniformity. Further, the. thermal an(l shear induced degradation are also less since possibilities of developing local high temperatures are less compared to a densely compacted extruder bed. This study has been undertaken mainly to explore the effect of feeding rate on the mechanical properties of rubber and plastic extrudates since the effect of feeding rate has not been analysed from this angle so far.

Reactive pozzolanas from rice husk ash: An alternative to cement for rural housing

This paper discusses the properties of rice husk ash samples produced from different types of field ovens to compare the performance of the ovens and to identify the most feasible method to produce a reactive pozzolana as an alternative to cement for building applications requiring lower strengths. Different types of ashes are produced and long-term strength of rice husk ash pozzolanas with lime or cement is investigated to suggest a sustainable affordable option in rural building applications, especially for rural housing in Kerala, a southern state of India