Hydrodynamic Study of Swirling Fluidized Bed and the Role of Distributor

The study aims to the hydrodynamic characteristics of swirling fluidized bed, using large particles (Geldart D-type) selected from locally available agricultural produce (coffee beans and black pepper). The important variables considered in the present study include percentage area of opening, angle of air injection and the percentage useful area of the distributor. A total of seven distributors have been designed and fabricated for a bed column of 300 mm, namely single row vane type distributors (15˚ and 20˚ vane angle), inclined hole type distributors (15˚ and 20˚ vane angle) and perforated plate distributors. The useful area of distributor of single row vane type, three now vane-type and inclined hole-type distributors are respectively 64%,91% and 94%. The hydrodynamic parameters considered in the present study include distributor pressure drop, air velocity, minimum fluidizing velocity, bed pressure drop, bed height and the bed behaviour. It has been observed that, in general, the distributor pressure drop decreases with an increase in the percentage area of opening, Further, and increase in the area of opening above 17% will not considerably reduce the distributor pressure drop. In the present study, for the distributor with an area of opening 17%, and corresponding to the maximum measured superficial velocity of 4.33 m/s, the distributor pressure drop obtained was 55.25mm of water. The study on the bed behavior revealed that, in a swirling fluidized bed, once swirl motion starts, the bed pressure drop increases with superficial velocity in the outer region and it decreases in the inner region. This means that, with higher superficial velocity, the air might get by-passed through the inner boundary of the bed (around the cone). So, depending on the process for which the bed is used, the maximum superficial velocity is to be limited to have an optimum bed performance.

Influence of Angle of Air Injection and Particles in Bed Hydrodynamics of Swirling Fluidized Bed

The thesis presented here unveils an experimental study of the hydrodynamic characteristics of swirling fluidized bed viz. pressure drop across the distributor and the bed, minimum fluidizing velocity, bed behaviour and angle of air injection. In swirling fluidized bed the air is admitted to the bed at an angle 'Ѳ' to the horizontal. The vertical component of the velocity v sin Ѳ causes fluidization and the horizontal component v cos Ѳ contributes to swirl motion of the bed material.The study was conducted using spherical particles having sizes 3.2 mm, 5.5 mm & 7.4 mm as the bed materials. Each of these particles was made from high density polyethylene, nylon and acetal having relative densities of 0.93, 1.05 and 1.47 respectively.The experiments were conducted using conidour type distributors having four rows of slits. Altogether four distributors having angles of air injection (Φ)- 0°, 5°, 10° & 15° were designed and fabricated for the study. The total number of slits in each distributor was 144. The area of opening was 6220 mm2 making the percentage area of opening to 9.17. But the percentage useful area of opening of the distributor was 96.The experiments on the variation of distributor pressure drop with superficial velocity revealed that the distributor pressure drop decreases with angle of air injection. Investigations related to bed hydrodynamics were conducted using 2.5 kg of bed material. The bed pressure drop measurements were made along the radial direction of the distributor at distances of 60 mm, 90 mm, 120 mm & 150 mm from the centre of the distributor. It was noticed that after attaining minimum fluidizing velocity, the bed pressure drop increases along the radial direction of the distributor. But at a radial distance of 90 mm from the distributor centre, after attaining minimum fluidizing velocity the bed pressure drop remains almost constant. It was also observed that the bed pressure drop varies inversely with particle size as well as particle density.An attempt was made to determine the effect of various parameters on minimum fluidizing velocity. It was noticed that the minimum fluidizing velocity varies directly with angle of air injection (Φ), particle size and particle density.The study on the bed behaviour showed that the superficial velocity required for initiating various bed phenomena (such as swirl motion and separation of particles from the cone at the centre) increase with increase in particle size as well as particle density. It was also observed that the particle size and particle density directly influence the superficial velocity required for various regimes of bed behaviour such as linear variation of bed pressure drop, constant bed pressure drop and sudden increase or decrease in bed pressure drop.Experiments were also performed to study the effect of angle of air injection (Φ). It was noticed that the bed pressure drop decreases with angle of air injection. It was also noticed that the angle of air injection directly influence the superficial velocity required for initiating various bed phenomena as well as the various regimes of bed behaviour.

An investigation into observational characteristics of rainfall and temperature in Central Northeast India—a historical perspective 1889–2008

Mann–Kendall non-parametric test was employed for observational trend detection of monthly, seasonal and annual precipitation of five meteorological subdivisions of Central Northeast India (CNE India) for different 30-year normal periods (NP) viz. 1889–1918 (NP1), 1919–1948 (NP2), 1949–1978 (NP3) and 1979–2008 (NP4). The trends of maximum and minimum temperatures were also investigated. The slopes of the trend lines were determined using the method of least square linear fitting. An application of Morelet wavelet analysis was done with monthly rainfall during June– September, total rainfall during monsoon season and annual rainfall to know the periodicity and to test the significance of periodicity using the power spectrum method. The inferences figure out from the analyses will be helpful to the policy managers, planners and agricultural scientists to work out irrigation and water management options under various possible climatic eventualities for the region. The long-term (1889–2008) mean annual rainfall of CNE India is 1,195.1 mm with a standard deviation of 134.1 mm and coefficient of variation of 11%. There is a significant decreasing trend of 4.6 mm/year for Jharkhand and 3.2 mm/day for CNE India. Since rice crop is the important kharif crop (May– October) in this region, the decreasing trend of rainfall during themonth of July may delay/affect the transplanting/vegetative phase of the crop, and assured irrigation is very much needed to tackle the drought situation. During themonth of December, all the meteorological subdivisions except Jharkhand show a significant decreasing trend of rainfall during recent normal period NP4. The decrease of rainfall during December may hamper sowing of wheat, which is the important rabi crop (November–March) in most parts of this region. Maximum temperature shows significant rising trend of 0.008°C/year (at 0.01 level) during monsoon season and 0.014°C/year (at 0.01 level) during post-monsoon season during the period 1914– 2003. The annual maximum temperature also shows significant increasing trend of 0.008°C/year (at 0.01 level) during the same period. Minimum temperature shows significant rising trend of 0.012°C/year (at 0.01 level) during postmonsoon season and significant falling trend of 0.002°C/year (at 0.05 level) during monsoon season. A significant 4– 8 years peak periodicity band has been noticed during September over Western UP, and 30–34 years periodicity has been observed during July over Bihar subdivision. However, as far as CNE India is concerned, no significant periodicity has been noticed in any of the time series.

Emotional Intelligence As A Determinant Of Conflict Style Adoption Of Managers: A Theoretical Perspective

Successful management is dependent heavily on the manager’s ability to handle conflict effectively. The workforce has been increasingly becoming diversified vis-à-vis the gender, culture and ethnicity. The present work environment has in itself contributed to sowing seeds of conflict with greater diversity, hostility, complexity and newer business competencies in the work context.The classic study of Mintzberg’s Managerial roles approach (1973) also says that a manager has to spend sufficient time and energy in solving conflict as he has to take roles as a negotiator, and dispute handler. An understanding of the conflict and role that it plays in influencing employee behavior constructively or destructively is immense. Therefore conflict when left unmanaged can lead to diminished cohesiveness amongst employees, productivity and reduced organizational fitness. To manage conflict effective conflict resolution strategies that have constructive outcomes is called for. Conflict resolution style theorists opine that collaborative or integrative style, where there is high concern for task and people is considered to give positive individual and organizational outcomes, while the withdrawing /avoidance style and forcing / dominating style are considered to be ineffective in managing conflict. Though managers have typical preferences in the styles followed it need not necessarily be the typical response as it depends on the context, power relationships, emotions etc. The adoption of conflict styles of managers however is dependent on variables like gender orientation, cultural values, personality orientation, underlying relationships – public/private. The paper attempts to draw the importance of managing conflicts at workplace positively and the need for effective conflict resolution strategies. The conflict style adopted and the variables that affect the adoption of each style are discussed and possible interventions at the workplace are suggested

Occurrence of filamentous algae and soil characteristics in the paddy fields of Kuttanad and Kole lands of Kerala

The present work is the study of filamentous algae in the paddy fields of Kuttanad and Kole lands of Kerala. This investigation was initiated by sampling of filamentous algae in Kuttanad during December 2010 to February 2011. A second phase of sampling was done from November 2011 to February 2012. The sampling periodicity corresponded to the crop growth starting from field preparation through sowing, and continued till the harvest. Sampling locations were selected from the active paddy cultivation regions of the six agronomic zones of Kuttanad. The numbers of sampling locations were proportional to the area of each zone. Algae of the Kole lands were collected during from October 2011 to January 2012. It was observed that blue-green algae dominated in both Kuttanad and Kole lands. Thirty two species of blue-green algae and eight species of green algae were identified from Kuttanad. The highest number of algal species was observed from Kayal lands in Kuttanad throughout the cropping season. Among the thirty two species of blue-green algae twenty five species are nonheterocystous and seven species are heterocystous. Twenty eight species of blue-green and six species of green algae were identified from Kole lands, and highest number of species was observed in Palakkal throughout the cropping season. Among the twenty eight species of blue-green algae collected from Kole lands twenty one species are non-heterocystous, and only seven species are heterocystous filamentous algae. Blooms of Spirogyra were observed during the second phase of sampling in Kuttanad and also in the Kole lands. The results of the germination study revealed that the extract of Spirogyra sp. inhibited seed germination and reduced seedling vigour. The growth of the treated seedlings was evaluated by pot experiments. The results clearly showed that Spirogyra sp. can negatively affect the seed germination, seedling vigour, and the yield of rice.