New Simulated Corrugated Scaltering Surface Giving Widebandcharacter I Sti Cs

Simultaneous elimination of specular reflection and backscattered power from a plane metallic surface by simulated corrugated surfaces of constant period and variable strip width for TM polarisation is reported. This new configuration offers almost a ten-fold frequency bandwidth compared with a regularly spaced strip grating of the same size.

STUDIES ON THE CELL STRUCTURE AND MECHANICAL PROPERTIES OF NR/LATEX RECLAIM/HSR BASED MICROCELLULAR SHEETS

In natural rubber/high styrene resin microcellular sheets, part of natural rubber was replaced by latex reclaim prepared from waste latex products. The mechanical properties and cell structure of the products were evaluated. It was found that latex reclaim can replace about 30% of natural rubber without affecting the technical properties of the microcellular sheets.

Corrugated Flanged Horn Feed for Offset Paraboloidal Reflectors

A technique for improving the coupling between a feed horn and reflector by using corrugated metallic flanges is presented. Experimental data for flanges of varying parameters are given and theoretical explanation is supplemented

Axially Symmetric Radiation Patterns from Corrugated

A modified H-plane sectoral horn antenna with identical E- and'H- plane.patterns over the X-band frequency is discussed. This system has significantly reduced side lobes and hack lobes. Half=power beam width and gain of the antenna are also improved with enhanced matching , Experimental results for a number of horns with various flanges are presented . These find practical application for illuminating symmetric antennas like paraboloids and polarization measurements in radio astronomy, etc. Compared to the fixed pyramidal horns. the present system offers great convenience in trimming the antenna characteristics

A Circularly Polarized Corrugated Flanged Feed Horn

Design and development of a circularly polarized and matched H-plane sectorial horn antenna have been reported By proper trimming of the flange parameters any desired polarization can be obtained from the horn

Corrugated flange technique for beam shaping of sectoral electromagnetic horn antennas

The need for improved feed systems for large reflector antennas employed in Radio Astronomy and Satellite tracking spurred the interest in horn antenna research in the 1960's. The major requirements were to reduce spill over, cross-polarisation losses,and to enhance the aperture efficiency to the order of about 75-8O%L The search for such a feed culminated in the corrugated horn. The corrugat1e 1 horn triggered widespread interest and enthusiasm, and a large amount of work(32’34’49’5O’52’53’58’65’75’79)has already been done on this type of antennas. The properties of corrugated surfaces has been investigated in detail. It was strongly felt that the flange technique and the use of corrugated surfaces could be merged together to obtain the advantages of both. This is the idea behind the present work. Corrugations are made on the surface of flange elements. The effect of various corrugation parameters are studied. By varying the flange parameters, a good amount of data is collected and analysed to ascertain the effects of corrugated flanges. The measurements are repeated at various frequencies, in the X— and S-bands. The following parameters of the system were studied: (a) beam shaping (b) gain (c) variation of V.S.U.R. (d) possibility of obtaining circularly polarised radiation from the flanged horn. A theoretical explanation to the effects of corrugated flanges is attempted on the basis of the line-source theory. Even though this theory utilises a simplified model for the calculation of radiation patterns, fairly good agreement between the computed pattern and experimental results are observed.

Formation of elliptically polarized beam from h-plane sectoral horns using corrugated flanges

The flange technique, suggested by Reynolds72 is simple technique to improve antenna characteristics. Using flange technique we can trim the antenna characteristic by suitably adjusting the flange parameters75. Later corrugated flanges87 are used for beam shaping. The important parameters of the corrugated flanges are (a) flange angle, (b) flange width, (c) flange position, (d) conductivity of the flange, (e) amplitude excitation of the flange elements, (f) period of corrugation etc. Compared to a compound horn the flange technique offers great convenience in trimming antenna characteristics. Horns are commonly used as a feed in radar and satellite communications. A large number of work had been done to improve the characteristics of horn antennas. It is an established fact that grooved walls on the inner surface of a horn can improve the antenna characteristics44. Corrugated comb surface can be used for the circular polarization98, tilt of polarization99 etc. This suggests the possibility to combine these two phenomena and to obtain a resultant beam. This thesis presents the result of an investigation to study the possibility of controlling different antenna characteristics like polarization, beam shaping, matching etc, using corrugated flange techniques.

Marine bacterial prodigiosin as dye for rubber latex, polymethyl methacrylate sheets and paper

Prodigiosin is known for its immunomodulatory, antibacterial, antimycotic, antimalarial, algicidal and anticancer activities. Here, we reported the evaluation of prodigiosin pigment as a dyeing agent in rubber latex, paper and polymethyl methacrylate (PMMA) so that it can be considered as an alternative to synthetic pigments. Maximum color shade was obtained in rubber sheet prepared with 0.5 parts per hundred gram of rubber (phr) pigment and PMMA sheet incorporated with 0.08 μg pigment. Results indicate scope for utilization of prodigiosin as dye for PMMA and rubber and also prodigiosin dyed paper as a pH indicator. Further, being a natural and water insoluble pigment, it is ecofriendly