Reactive loaded microstrip leaky wave antenna for low cost beam steering applications

A novel fixed frequency beam scanning microstrip leaky wave antenna is reported. The beam scanning at fixed frequency is achieved by reactive loading. Simulation and measured results shows frequency scanability of 80° as well as fixed frequency beam steering of 68° over the −10 dB impedance band of 4.56–5.06 GHz.

C-shaped slot loaded reconfigurable microstrip antenna

A new electronically reconfigurable dual frequency microstrip patch antenna with highly simplified varactor tuning circuitry is presented. The proposed design allows relatively independent selection of the two operating frequencies. Tuning ranges of 7.1 and 4.1% are realised for the two resonant frequencies without the use of any matching circuits.

Investigations on Reconfigurable Dual Frequency Microstrip Antennas Controlled by PIN Diodes and Varactors

In this work,we investigate novel designs of compact electronically reconfigurable dual frequency microstrip antennas with a single feed,operating mainly in L-band,without using any matching networks and complicated biasing circuitry.These antennas have been designed to operate in very popular frequency range where a great number of wireless communication applications exist.Efforts were carried out to introduce a successful,low cost reconfigurable dual-frequency microstrip antenna design to the wireless and radio frequency design community.

Investigations on Broadband Plannar Monoplole Antennas with Truncated Ground Plane

The space constraints on wireless gadgets is a challenge to antenna designers as the ground plane dimensions of the printed monopole significantly affect s the antenna characteristics.Investigations on ground plane truncations have led to the development of an extremely broad band printed monopole antenna.Omnidirectional radiation characteristics with moderate gain makes this antenna highly suitable for mobile/wireless applications .This thesis also highlights the development of UWB printed antenna along with design equations .Optimum ground plane dimensions for compact antenna applications,folding technique for miniaturization and double folding for dual band application are the other highlights of this thesis.

A new corner reflector antenna with periodic strip subreflectors

This paper presents the design of a new type of corner reflector (CR) antenna and the experimental investigation of its radiation characteristics. The design involves the addition of planar parallel periodic strips to the two sides of a CR antenna. The position, angular orientation, and number of strips have a notable effect on the H-plane radiation characteristics of the antenna. Certain configurations of the new antenna are capable of producing very sharp axial beams with gain on the order of 5 dB over the square corner reflector antenna. A configuration that can provide symmetric twin beams with enhanced gain and reduced half-power beam width (HPBW) is also presented.

Investigations on the Radiation Characteristics of Broadband Strip Loaded Slotted Microstrip Antennas

With the recent progress and rapid increase in mobile terminals, the design of antennas for small mobile terminals is acquiring great importance. In view of this situation, several design concepts are already been addressed by the scientists and engineers. Compactness and efficiency are the major criteria for mobile terminal antennas. The challenging task of the microwave scientists and engineers is to device compact printed radiating systems having broadband behavior, together with good efficiency. Printed antenna technology has received popularity among antenna scientists after the introduction of microstrip antenna in 1970s. The successors in this kind such as printed monopoles and planar inverted F are also equally important. Scientists and Engineers are trying to explore this technology as a viable coast effective solution for forthcoming microwave revolution. The transmission line perspectives of antennas are very interesting. The concept behind any electromagnetic radiator is simple. Any electromagnetic system with a discontinuity is radiating electromagnetic energy. The size, shape and the orientation of the discontinuities controls the radiation characteristics of the system such as radiation pattern, gain, polarization etc. It can be either resonant or non resonant structure. Microstrip antennas are suitable for wireless applications due to their low cost, high gain and ease of fabrication. But the major disadvantage of micro strip antennas is their inherent narrow bandwidth. A lot of techniques are introduced by the researchers all over the world to enhance the bandwidth of micro strip patch antennas. The thesis addresses an attempt to enhance the bandwidth of micro strip patch antennas by incorporating impedance matching strip as a part of the micro strip patch antenna. The first part of the thesis deals with the broadband operation of the tilted square slot and polygonal slot loaded square micro strip patch antennas. The resonant mechanisms are clearly mentioned using the simulation and experimental studies. The bandwidth of the polygonal slotted broadband patch antenna is again enhanced by implementing an Lstrip feed mechanism. In the second major part of the thesis, a novel gain enhancement technique for single band and broadband square micro strip patch antennas is achieved by implementing offset stacked configurations.

Modifications of secondary reflector antenna patterns due to shaped beams from flanged primary horn feeds

With the advent of satellite communication and radio astronomy, the need for large and efficient reflector antennas had triggered a widespread investigation in reflector feed design techniques. Major improvements sought are reduction in spill-over, cross polarization losses and the enhancement of aperture efficiency. The search for such a feed culminated in the corrugated horn. The main idea behind the present work is to use the H-plane sectoral horns fitted with,corrugated flanges as feeds of a paraboloid and see how the secondary pattern of the reflector antenna varies with different parameters of the feed. An offset paraboloid is used as the secondary reflector in order to avoid the adverse effect of aperture ‘blocking by the feed horn structure on the secondary radiation pattern. The measurements were repeated for three different H-plane sectoral horns with the same set of corrugated flanges at various X-band frequencies. The following parameters of the whole system are studied: (a) Beam shaping. (b) Gain. (c) Variation of VSWR and (d) Cross polarization

Decimal Multiplication using compact BCD Multiplier

Decimal multiplication is an integral part offinancial, commercial, and internet-based computations. The basic building block of a decimal multiplier is a single digit multiplier. It accepts two Binary Coded Decimal (BCD) inputs and gives a product in the range [0, 81] represented by two BCD digits. A novel design for single digit decimal multiplication that reduces the critical path delay and area is proposed in this research. Out of the possible 256 combinations for the 8-bit input, only hundred combinations are valid BCD inputs. In the hundred valid combinations only four combinations require 4 x 4 multiplication, combinations need x multiplication, and the remaining combinations use either x or x 3 multiplication. The proposed design makes use of this property. This design leads to more regular VLSI implementation, and does not require special registers for storing easy multiples. This is a fully parallel multiplier utilizing only combinational logic, and is extended to a Hex/Decimal multiplier that gives either a decimal output or a binary output. The accumulation ofpartial products generated using single digit multipliers is done by an array of multi-operand BCD adders for an (n-digit x n-digit) multiplication.

“Design and Development of Coplanar Strip Fed Planar Antennas”

With the recent progress and rapid increase in the field of communication, the designs of antennas for small mobile terminals with enhanced radiation characteristics are acquiring great importance. Compactness, efficiency, high data rate capacity etc. are the major criteria for the new generation antennas. The challenging task of the microwave scientists and engineers is to design a compact printed radiating structure having broadband behavior along with good efficiency and enhanced gain. Printed antenna technology has received popularity among antenna scientists after the introduction of planar transmission lines in mid-seventies. When we view the antenna through a transmission line concept, the mechanism behind any electromagnetic radiator is quite simple and interesting. Any electromagnetic system with a discontinuity is radiating electromagnetic energy. The size, shape and orientation of the discontinuities control the radiation characteristics of the system such as radiation pattern, gain, polarization etc. It can be either resonant or non-resonant. This thesis deals with antennas that are developed from a class of transmission lines known as coplanar strip-CPS, a planar analogy of parallel pair transmission line. The specialty of CPS is its symmetric structure compared to other transmission lines, which makes the antenna structures developed from CPS quite simple for design and fabrication. The structural modifications on either metallic strip of CPS results in different antennas. The first part of the thesis discusses a single band and dual band design derived from open ended slot lines which are very much suitable for 2.4 and 5.2 GHz WLAN applications. The second section of the study is vectored into the development of enhanced gain dipoles. A single band dipole and a wide band enhanced gain dipole suitable for 5.2/5.8 GHZ band and imaging applications are developed and discussed. Last part of the thesis discusses the development of directional UWBs. Three different types of ultra-compact UWBs are developed and almost all the frequency domain and time domain analysis of the structures are discussed.

Slot Line Fed Dipole Antenna For Wide Band Applications

A slot line fed planar dipole antenna with a parasitic strip for wide band applications is presented. The presented antenna offers a 2:1 VSWR bandwidth from 1.66 to 2.71 GHz covering the DCS/ PCS/UMTS and IEEE 802.11b/g bands with a gain better than 6.5 dBi. The uniplanar design, simple feeding, and high gain make it a versatile antenna for wireless applications

Chipless RFID Tag Using Multiple Microstrip Open Stub Resonators

A novel compact RFID tag employing open stubs in a microstrip transmission line is proposed. The prototype of the tag is fabricated on a substrate of dielectric constant 4.4 and loss tangent 0.0018. The tag consists of microstrip open stub resonators and cross polarized transmitting and receiving disc monopole antennas. A prototype of 8 bit data encoded tag is demonstrated in this communication. Method for enhancing the performance of the RFID tag is also proposed. Magnitude or group delay response can be used to decode the tag informations

Rectangular Dielectric Resonator Antenna Configurations For Mobile Communication Applications

Experimental investigations on Microstrip line excited Dielectric Resonator Antenna configurations suitable for Mobile Communication applications are reported. High permittivity (εrd = 48) resonator samples with different aspect ratios are employed for the study. Theoretical analysis performed using FDTD method is also presented.

A Novel Planar Fractal Antenna with CPW-Feed for Multiband Applications

In this paper, a multiband antenna using a novel fractal design is presented. The antenna structure is formed by inscribing a hexagonal slot within a circle. This base structure is then scaled and arranged within the hexagon along its sides without touching the outer structure. The proposed CPW fed, low profile antenna offers good performance in the 1.65 – 2.59 GHz, 4.16 – 4.52 GHz and 5.54 – 6.42 GHz bands and is suitable for GSM 1800/1900, Bluetooth, IMT advanced systems and upper WLAN applications. The antenna has been fabricated on a substrate of height 1.6 mm and εr = 4.4 and simulation and experimental results are found to be in good agreement

Conformal FDTD analysis of an Octagonal Microstrip Patch antenna

The recent boom in wireless communication industry, especially in the area of cellular telephony and wireless data communication, has led to the increased demand for multi band antennas. In such applications the issues to be addressed are, wide bandwidth and gain, while striving for miniature geometry. A dual frequency configuration useful in GSM1800 and Blue tooth, is one that operates with similar properties, both in terms of reflection and radiation characteristics, in the two bands of interest. Dual frequency operations can be realized by exciting the Microstrip Patch Antenna (MPA) using a single feed [1] or dual feed [2]. In this paper, Conformal FDTD[3] method with Perfect Magnetic Conductor (PMC) applied along the plane of symmetry [4] is used to study the characteristics of an Octagonal MPA. The theoretical results are compared against the experimental and IE3D™ simulated results

Electromagnetically Coupled Dual Port, Dual Band, Octagonal Patch Antenna

In this paper, a dual port, dual frequency, dual polarized, octagonal shaped Microstrip patch antenna, suitable for GPS applications is discussed experimentally and theoretically. The proposed antenna configuration is characterized by good impedance bandwidth, gain, isolation between two ports and broad radiation patterns