Studies on Photosensitive polymers for Optical Recording

Department of Polymer Science and Rubber Technology,Cochin University of Science and Technology

Thermal lens technique to study the effect of pH on electronic energy transfer in organic dye mixtures.

The effect of pH on the fluorescence efficiency of fluorescein is evaluated using thermal lens technique. Fluorescence efficiency increases as the sample becomes more and more alkaline. But when fluorescein is mixed with rhodamine B fluorescence quenching of fluorescein takes place with the excitation of rhodamine B. The electronic energy transfer in this mixture is investigated using Optical Parametric Oscillator as the excitation source. The effect of pH on the efficiency of energy transfer in fluorescein–rhodamine B mixture is presented.

Modification of Polypropylene and Polystyrene Using Nanosilica

The present work focuses on the modification of the commonly used thermoplastics, polypropylene and polystyrene using nanosilica preparcd from a cheap source of sodium silicate. Melt compounding technique has been used for nanocomposite preparation as it is simple and suited to injection moulding. Nanosilica in a polymer matrix provide significant enhancement in strength, stiffness and impact strength. Incorporation of silica particles in a polymer also improves its thennal stability. To achieve better dispersion of fillers in polymer matrices the mixing was done at different shear rates. The enhancement in material properties indicates that at higher shear rates there is greater interaction between particles and the matrix and it depends on filler concentration and type of polymer used. N anosilica is a useful filler in thennoplastic polymers and has been applied in automotive applications, electronic appliances and consumer goods.This thesis is divided into six chapters. General introduction to the topic is described in chapter 1. Salient features of polymer nanocomposites, their synthesis, properties and applications are presented. A review of relevant literature and the scope and objectives are also mentioned in this chapter.The materials used and the vanous experimental method and techniques employed in the study are described in chapter 2. Preparation of nanocomposites by melt blending using Thenno Haake Rheocord, preparation of samples, evaluation of mechanical and thennal properties using UTM, Impact testing and characterization using DMA, TGA and DSC and morphology by SEM are described.The preparation of nanosilica from a laboratory scale to a pilot plant scale is described in chapter 3. Generation of surface modified silica, evaluation of kinetic parameters of the synthesis reaction, scale up of the reactor and modeling of the reactor are also dealt with in this chapter.The modification of the commodity thennoplastic, Polypropylene using nanosilica is described in chapter 4. Preparation of PP/silica nanocomposites, evaluation of mechanical properties, thermal and crystallization characteristics, water absorption and ageing resistance studies are also presented.The modification of Polystyrene using synthesized nanosilica IS described in chapter 5. The method of preparation of PS/silica nanocomposites, evaluation of mechanical properties (static and dynamic), thermal properties melt flow characteristics using Haake Rheocord, water absorption and ageing resistance of these nanocomposites are studied.

Farm Programmes of Electronic Media: A Comparative Study of Audience Perception in Kerala

Farm communication and extension programs are vital part of the farm development attempts. Electronic media plays a major role in farm extension activities. Kerala, the consumer state, which was a complete agricultural state in pre-independence period, is the sprouting land of agricultural extension and publication activities in print media. Later AIR (All India Radio) farm programs and farm broadcasting of Doordarshan enriched the role of electronic media in farm extension activities. The media saturated southern state of India received this new electronic media farm communication revolution whole heartedly. However, after 1990, Kerala witnessed a flood of private T V channels and currently there are 24 channels in this regional language, named Malayalam. All major news and entertainment channels are broadcasting farm programs. Farm programs of AIR and Doordarshan, broadcasted in Malayalam language, have been well accepted to the farmers‘ in Kerala. However, post-independence period, witnessed the formation of Kerala state in Indian Union and the first ballot-elected communist Government started its administration. After the land reform bills, the state witnessed a gradual decrease in agricultural production. Even if it is not reflected much in the attitude and practices of farm community and farm broadcast of traditional electronic broadcasting, a change is observable after the post-liberalization era of India. Private Television channels, which were focused on entertainment value of programs, started broadcasting farm programs and the parameters of program production went through certain changes. In this situation, there is ample relevance for a study about the farm programs of electronic media in terms of a comparative study of audience perception. The study is limited in the state of Kerala as it is the most media saturated state in India. The study analyzes the rate, nature and scope of adoption of farming methods transmitted through electronic media (T.V. and Radio) in Malayalam language.All kinds of Farm programs including comprehensive program serials, success stories, seasonal cropping methods, experts opinion, been analyzed on the basis of the following objectives.  To find whether propagating new farm methods through farm programs in electronic media or the availability of adequate infrastructure and economic factors make a farmer to adopt a new farming method.  To find which electronic media has more influence on farmers to adopt agricultural programs.  To find which form of electronic media gets better feedback from farmers  To find out whether the programs of T.V. or Radio is more acceptable to farmers than the print media.  To find whether farmers gets the message through their preferred medium for the message. The researcher recorded opinions from a panel of agricultural officers, farm Information officers, agro extension researchers and experts. According to their opinions and guidelines, a pilot study is designed and conducted in Kanjikuzhy Panchayath, in Alappuzha district, Kerala. The Panchayath is selected by considering its ideal nature of being the sample for a social Science research. Besides, the nature of farming in the Panchayath, which devoid of the cultivation of cash crops also supported its sample value. As per the observations from the pilot study, researcher confirmed the Triangulation method as the methodology of research. The questionnaire survey, being the primary part contained 42 Questions with 6 independent and 32 dependent variables. The survey is conducted among 400 respondents in Idukki, Alappuzha and Pathanamthitta districts considering geographical differences and distribution of different types of crops. The response from a total of 360 respondents, 120 from each district, finally selected for tabulation and data analysis.The data analysis, based on percentage analysis, along with the results from focus group discussion among a selected group of 20 farmers, together produced the results as follows. Farmers, who are the audience of farm programs, have a very serious approach towards the medium. They are maintaining a critical point of view towards the content of the programs. Farmers are reasonably aware about the financial side of the programs and the monitory aspirations of both private and Government owned Television channels. Even though, the farmers are not aware on the technical terminology and jargons, they have ideas about success stories, program serials and they are even informed about channels are not maintaining an audience research section like AIR. Though the farmers accept Doordarshan as the credential source of farm information and methods, they are inclined to the entertainment value of programs too. They prefer to have more entertainment value for the programs of Doordarshan. Surprisingly, they have very solid suggestions on even about the shots which add entertainment value to the farm broadcasting methods of Doordarshan. Farmers are very much aware about the fact that media is just an instrument for inspiration and persuasion. They strongly believe that the source of information and new methods is agricultural research and an effective change happens only when there are adequate infrastructure and marketing facilities, along with the proper support from Government agricultural guideline and support systems like Krishi Bhavans. They strongly believe that media alone cannot create any magic in increasing agricultural production. Farmers are pointing out the lack of response to the feedback and queries of farmers on farming methods, as an evidence for the difference in levels of commitment of Government and private owned Television channels.Farmers are still perceiving AIR farm programs are far more committed to farmers and farming than any other electronic medium. However, they are seriously lacking Radio receivers with medium wave reception facility. Farmers perceive that the farming methods on new crops are more adoptable than the farming methods of traditional crops in both private and Government owned Television channels. There are multiple factors behind this observation from farmers. Farmers changed in terms of viewing habits and they prefer success stories, which are totally irrelevant and they even think that such stories encourage people to go for farming and they opined that such stories are good sources of inspiration. However, they are all very much sure about the importance and particular about the presence of entertainment factor even in farm programs. Farmers expect direct interaction of any expert of the new farming method to implement the method in their agriculture practices. Though introduction of a new idea in the T.V. is acceptable, farmers need the direct instruction of expert on field to start implementing the new farming practices Farmers still have an affinity towards print media reports and agricultural pages and they have complaints to print media on the removal of agricultural information pages from news papers. They prefer the reports in print media as it facilitates them to collect and refer articles when they need it. Farmers are having an eye of doubt about the credibility of farm programs by private T.V. channels. Even if they prefer private Television channels for listening and adopting new farming methods and other farm information, they scrutinize programs to know whether they are sponsored programs by agrochemical or agro-fertilizer manufacturer.

Growth and characterisation of p-type delafossite transparent conducting thin films for heterojunction applications

In the present studies, various copper delafossite materials viz; CuAlO2, CuGaO2, CuFeO2 , CuGa1-xFexO2, CuYO2 and CuCaxY1-xO2 were synthesised by solid state reaction technique. These copper delafossite materials were grown in thin film form by rf magnetron sputtering technique. In general copper delafossites exhibit good optical transparency. The conductivity of the CuYO2 could be improved by Ca doping or by oxygen intercalation by annealing the film in oxygen atmosphere. It has so far been impossible to improve the p-type conductivity of CuGaO2 significantly by doping Mg or Ca on the Ga site. The ptype conductivity is presumed to be due to oxygen doping or Cu Vacancies [6]. Reports in literature show, oxygen intercalation or divalent ion doping on Ga site is not possible for CuGaO2 thin films to improve the p-type conductivity. Sintered powder and crystals of CuFeO2 have been reported as the materials having the highest p-type conductivity [14, 15] among the copper and silver delafossites. However the CuFeO2 films are found to be less transparent in the visible region compared to CuGaO2. Hence in the present work, the solid solution between the CuGaO2 and CuFeO2 was effected by solid state reaction, varying the Fe content. The CuGa1-xFexO2 with Fe content, x=0.5 shows an increase in conductivity by two orders, compared to CuGaO2 but the transparency is only about 50% in the visible region which is less than that of CuGaO2 The synthesis of α−AgGaO2 was carried out by two step process which involves the synthesis of β-AgGaO2 by ion exchange reaction followed by the hydrothermal conversion of the β-AgGaO2 into α-AgGaO2. The trace amount of Ag has been reduced substantially in the two step synthesis compared to the direct hydrothermal synthesis. Thin films of α-AgGaO2 were prepared on silicon and Al2O3 substrates by pulsed laser deposition. These studies indicate the possibility of using this material as p-type material in thin film form for transparent electronics. The room temperature conductivity of α-AgGaO2 was measured as 3.17 x 10-4 Scm-1and the optical band gap was estimated as 4.12 eV. A transparent p-n junction thin film diode on glass substrate was fabricated using p-type α-AgGaO2 and n-ZnO.AgCoO2 thin films with 50% transparency in the visible region were deposited on single crystalline Al2O3 and amorphous silica substrates by RF magnetron sputtering and p type conductivity of AgCoO2 was demonstrated by fabricating transparent p-n junction diode with AgCoO2 as p-side and ZnO: Al as n-side using sputtering. The junction thus obtained was found to be rectifying with a forward to reverse current of about 10 at an applied voltage of 3 V.The present study shows that silver delafossite thin films with p-type conductivity can be used for the fabrication of active devices for transparent electronics applications.

Novel Approaches to Biodegradable Polymers: Synthesis and Biodegradation Studies

Biodegradable polymers have opened an emerging area of great interest because they are the ultimate solution for the disposal problems of synthetic polymers used for short time applications in the environmental and biomedical field. The biodegradable polymers available until recently have a number of limitations in terms of strength and dimensional stability. Most of them have processing problems and are also very expensive. Recent developments in biodegradable polymers show that monomers and polymers obtained from renewable resources are important owing to their inherent biodegradability, biocompatibility and easy availability. The present study is, therefore, mostly concemed with the utilization of renewable resources by effecting chemical modification/copolymerization on existing synthetic polymers/natural polymers for introducing better biodegradability and material properties.The thesis describes multiple approaches in the design of new biodegradable polymers: (1) Chemical modification of an existing nonbiodegradable polymer, polyethylene, by anchoring monosaccharides after functionalization to introduce biodegradability. (2) Copolymerization of an existing biodegradable polymer, polylactide, with suitable monomers and/or polymers to tailor their properties to suit the emerging requirements such as (2a) graft copolymerization of lactide onto chitosan to get controlled solvation and biodegradability and (2b) copolymerization of polylactide with cycloaliphatic amide segments to improve upon the thermal properties and processability.

Functionalized Silicon Polymers: Novel Materials for Catalysis

Dept.of Applied Chemistry,Cochin University of Science and Technolgy

Design and Synthesis of Conjugated Polymers for Photovoltaic and Chemosensor Applications

Department of Applied Chemistry, Cochin University of Science and Technology

Investigations on polyaniline based systems for technologically important applications and some novel polymers as prospective candidates for fabricating polymer light emitting diodes

Light emitting polymers (LEP) have drawn considerable attention because of their numerous potential applications in the field of optoelectronic devices. Till date, a large number of organic molecules and polymers have been designed and devices fabricated based on these materials. Optoelectronic devices like polymer light emitting diodes (PLED) have attracted wide-spread research attention owing to their superior properties like flexibility, lower operational power, colour tunability and possibility of obtaining large area coatings. PLEDs can be utilized for the fabrication of flat panel displays and as replacements for incandescent lamps. The internal efficiency of the LEDs mainly depends on the electroluminescent efficiency of the emissive polymer such as quantum efficiency, luminance-voltage profile of LED and the balanced injection of electrons and holes. Poly (p-phenylenevinylene) (PPV) and regio-regular polythiophenes are interesting electro-active polymers which exhibit good electrical conductivity, electroluminescent activity and high film-forming properties. A combination of Red, Green and Blue emitting polymers is necessary for the generation of white light which can replace the high energy consuming incandescent lamps. Most of these polymers show very low solubility, stability and poor mechanical properties. Many of these light emitting polymers are based on conjugated extended chains of alternating phenyl and vinyl units. The intra-chain or inter-chain interactions within these polymer chains can change the emitted colour. Therefore an effective way of synthesizing polymers with reduced π-stacking, high solubility, high thermal stability and high light-emitting efficiency is still a challenge for chemists. New copolymers have to be effectively designed so as to solve these issues. Hence, in the present work, the suitability of a few novel copolymers with very high thermal stability, excellent solubility, intense light emission (blue, cyan and green) and high glass transition temperatures have been investigated to be used as emissive layers for polymer light emitting diodes.

Energetic Polymers

High energy materials are essential ingredients in both rocket and explosive formulations. These can be vulnerable due to maltreatment. During gulf war, several catastrophic accidents have been reported from their own payload munitions. The role of energetic binders here was to wrap the explosive formulations to convert it into insensitive munitions. With the aid of energetic binders, the explosive charges are not only protected from tragic accidents due to fire, bullet impact, adjacent detonation, unplanned transportation, but also form total energy output presumption. The use of energetic binders in rocket propellants and explosive charges has been increased after the Second World War. Inert binders in combination with energetic materials, performed well as binders but they diluted the final formulation. Obviously the total energy output was reduced. Currently, the research in the field of energetic polymers is an emerging area, since it plays crucial role in insensitive munitions. The present work emphasises on the synthesis and characterization of oxetanes, oxiranes and polyphosphazene based energetic polymers. The thesis is structured into six chapters. First part of chapter 1 deals with brief history of energetic polymers. The second part describes a brief literature survey of energetic polymers based on oxetanes and oxiranes. Third and fourth parts deal with energetic plasticizers and energetic polyphosphazenes. Finally, the fifth part deals with the various characterization techniques adopted for the current study and sixth part includes objectives of the present work.

Structural studies on some metal complexes of embelin

This thesis deals with the studies on the synthesis and characterisation of the complexes of embelin with manganese (II), cobalt(II), nickel (II), copper (II), zinc (II), cadmium (II), chromium (III), iron (III) lanthanum(III), praseodymium (III) neodymium (III) Samarium (III), gadolinium (III) dysprosium (III), yttrium (III) thorium (IV) and uranium (VI). Elemental analysis as well as spectral, thermal and magnetic data were used to ascertain the composition of the complexes and to establish the structures of the metal complexes. Wherever possible, the electronic spectra and magnetic data were used to predict the stereochemistry of the complexes.The thesis is divided into four chapters.

An investigation on the preparation and properties of some transparent conducting oxides and lead selenide thin films”

The investigation of physical properties of matter has progressed so much during the last hundred years. Today physics is divided in to a large distinct group of special branches. These branches are distinguished by the particular area studied, method of investigation and so on. An independent and important branch that has developed is the physics ofthin films.Any object in solid or liquid form with one of its dimensions very much smaller than that of the other two may be called a thin film. It is having only one common property, namely, one of their dimensions is very small, though all their physical properties may be different. Thin layers of oil, floating on the surface of water, with their fascinating colours, have attracted men’s curiosity from time immemorial. The earliest application of thin films was the protective coatings in the form of paints. A thin layer of tin has been used from ancient times to protect copper utensils from corrosion. Indium thin films are used in certain applications on account of their good lubricating property. Relay contacts are coated with thin films of rare earth metals in order to prevent burning due to arcing. Hard coatings are also available using diamond like carbon (i-carbon). The basic properties of thin films are of considerable interest because of their potential applications in various fields of science and technology

Studies on High- Tc Superconductors with Inequivalent Conducting Layers

The thesis deals with the study of super conducting properties of layered cuprates within the frame work of a modified Lawrence-Doniach (LD) model. The thesis is organized in seven chapters. Chapter I is a survey of the phenomena and theories of conventional superconductivity which can serve as a springboard for launching the study of the new class of oxide superconductors and it also includes a chronological description of the efforts made to overcome the temperature barrier. Chapter II deals with the structure and properties of the copper oxide superconductors and also the experimental constraints on the theories of high te:::nperature superconductivity. A modified Lawrence-Doniach type of phenomenological model which forms the basis of the presnt study is also discussed. In chapter III~ the temperature dependence of the upper critical field both parallel and perpendicular to the layers is determined and the results are compared with d.c. magnetization measurements on different superconducting compoilllds. The temperature and angular dependence of the lower critical field both parallel and perpendicular to the layers is also discussed. Chapters IV, V and VI deal with thermal fluctuation effects on superconducting properties. Fluctuation specific heat is studied in chapter IV. Paraconductivity both parallel and perpendicular to the layers is discussed in chapter V. Fluctuation diamagnetism is dealt with in chapter VI. Dimensional cross over in the fluctuation regime of all these quantities is also discussed. Chapter VII gives a summary of the results and the conclusions arrived at.

Acid-Base. Surface Electron Donatin6 &.Catai.Ytlc Properties Of Some Binary Mixed Oxides Containing Rare Earth Elements

Catalysis research underpins the science of modern chemical processing and fuel technologies. Catalysis is commercially one of the most important technologies in national economies. Solid state heterogeneous catalyst materials such as metal oxides and metal particles on ceramic oxide substrates are most common. They are typically used with commodity gases and liquid reactants. Selective oxidation catalysts of hydrocarbon feedstocks is the dominant process of converting them to key industrial chemicals, polymers and energy sources.[1] In the absence of a unique successfiil theory of heterogeneous catalysis, attempts are being made to correlate catalytic activity with some specific properties of the solid surface. Such correlations help to narrow down the search for a good catalyst for a given reaction. The heterogeneous catalytic performance of material depends on many factors such as [2] Crystal and surface structure of the catalyst. Thermodynamic stability of the catalyst and the reactant. Acid- base properties of the solid surface. Surface defect properties of the catalyst.Electronic and semiconducting properties and the band structure. Co-existence of dilferent types of ions or structures. Adsorption sites and adsorbed species such as oxygen.Preparation method of catalyst , surface area and nature of heat treatment. Molecular structure of the reactants. Many systematic investigations have been performed to correlate catalytic performances with the above mentioned properties. Many of these investigations remain isolated and further research is needed to bridge the gap in the present knowledge of the field.