SRR loaded waveguide band rejection filter with adjustable bandwidth

The use of a split-ring resonator (SRR)-loaded waveguide for the design of a band-rejection filter with adjustable bandwidth is reported. The width of the stopband can be adjusted by suitably positioning the SRR array in the waveguide. The rejection band can be made very narrow by placing the array at the electric-field minimum. The stopband attenuation depends on the number of unit cells in the array.

Novel Low Loss A(A1/4 B2/4 C1/4)O3 Dielectrics and Their Applications In Broadband Antennas

This thesis presents the microwave dielectric properties of two novel dielectric resonator materials with the composition Ca(Ca1/4Nb2/4Ti1/4)O3 and Ca(Ca1/4Ta2/4Ti1/4)O3 ceramics and their application in the fabrication of wideband antennas. The microwave dielectric properties of the ceramics were tailored by several techniques such as doping, glass addition and solid solution formations in the complex perovskite A and B-sites with suitable substitutions. Among the wide variety of DRs developed, ceramic resonators with optimum properties were identified to fabricate broadband dielectric resonator loaded microstrip patch antennas. Furthermore, wideband, high permittivity dielectric resonator antennas were fabricated and explored the possibility of tuning their characteristics by modifying the feed line geometries.

Frequency Coded Chipless RFID Tag using Spurline Resonators

A novel compact chipless RFID tag using spurline resonators is discussed in this paper. The detection of the tag's ID is using the spectral signature of a spurline resonator circuit. The tag has a data capacity of 8-bits in the range 2.38 to 4.04 GHz. The tag consists of a spurline multiresonating circuit and two cross polarized antennas. The prototype of the tag is fabricated on a substrate CMET/ LK4.3 of dielectric constant 4.3 and loss tangent 0.0018. The measured results show that group delay response can also be used to decode the tag’s identity

Ga Optimized Srr Calculator

Negative magnetic permeability media (NMPM) can be built up by using small resonant metallic particles like Split ring resonator (SRR) which has very high magnetic polarisability. A group of these particles shows a negative permeability region near and above the resonant frequency. The continuous medium parameters describing the SRR array can be predicted from their individual electromagnetic behavior near the resonances. The paper presents an optimizing software using Genetic Algorithm (GA) to design an edge coupled two ring SRR for a particular frequency

Design and Development of Spectral Signature Based Chipless RFID Tags

The main objective of this thesis is to design and develop spectral signature based chipless RFID tags Multiresonators are essential component of spectral signature based chipless tags. To enhance the data coding capacity in spectral signature based tags require large number of resonances in a limited bandwidth. The frequency of the resonators have to be close to each other. To achieve this condition, the quality factor of each resonance needs to be high. The thesis discusses about various types of multiresonators, their practical implementation and how they can be used in design. Encoding of data into spectral domain is another challenge in chipless tag design. Here, the technique used is the presence or absence encoding technique. The presence of a resonance is used to encode Logic 1 and absence of a speci c resonance is used to encode Logic 0. Di erent types of multiresonators such as open stub multiresonators, coupled bunch hairpin resonators and shorted slot ground ring resonator are proposed in this thesis.

Investigations on selected chalcogenide glasses towards the realization of photonic devices

Among various optical sensing schemes, infrared spectroscopy is a powerful tool for detecting and determining the composition of complex organic samples since vibrational finger prints of all biomolecules and organic species are located in this window. This spectroscopic technique is simple, reliable, fast, non-destructive, cost-effective while having low sensitivity. Use of metallic nanoparticles in association with a good IR transparent sensing substrate, is one of the promising solutions to enhance the sensitivity. Chalcogenide glasses are promising substrate material because of their extended optical transmission window starting from the visible to the far infrared range up to 20 μm, high refractive index usually between 2 and 3 and high optical nonlinearity, which make them good candidates as IR sensors and optical ultrafast nonlinear devices. These glasses are favorable sensor materials for the infrared spectral range because of their high IR transparency to allow for low optical loss at wavelengths corresponding to the characteristic optical absorption bands of organic molecules, high refractive index for tight confinement of optical energy within the resonator structure, processibility into thin film form, chemical compatibility for adhesion of silver nano particles and thin films and resistance to the chemical environment to be sensed. Molecules adsorbed to silver island structures shows enhanced IR absorption spectra and the extent of enhancement is determined by many factors such as the size, density and morphology of silver structures, optical and dielectric properties of the substrate material etc.

Fabrication, Optical Analysis and Photonic Applications of Certain Metallic Nanostructure-Integrated Dye Doped Polymer Optical Fibers” submitted by Ms. Suneetha Sebastian

Polymer Optical Fibers have occupied historically a place for large core flexible fibers operating in short distances. In addition to their practical passive application in short-haul communication they constitute a potential research field as active devices with organic dopants. Organic dyes are preferred as dopants over organic semiconductors due to their higher optical cross section. Thus organic dyes as gain media in a polymer fiber is used to develop efficient and narrow laser sources with a tunability throughout the visible region or optical amplifier with high gain. Dyes incorporated in fiber form has added advantage over other solid state forms such as films since the pump power required to excite the molecules in the core of the fiber is less thereby utilising the pump power effectively. In 1987, Muto et.al investigated a dye doped step index polymer fiber laser. Afterwards, numerous researches have been carried out in this area demonstrating laser emission from step index, graded index and hollow optical fibers incorporating various dyes. Among various dyes, Rhodamine6G is the most widely and commonly used laser dye for the last four decades. Rhodamine6G has many desirable optical properties which make it preferable over other organic dyes such as Coumarin, Nile Blue, Curcumin etc. The research focus on the implementation of efficient fiber lasers and amplifiers for short fiber distances. Developing efficient plastic lasers with electrical pumping can be a new proposal in this field which demands lowest possible threshold pump energy of the gain medium in the cavity as an important parameter. One way of improving the efficiency of the lasers, through low threshold pump energy, is by modifying the gain of the amplifiers in the resonator/cavity. Success in the field of Radiative Decay Engineering can pave way to this problem. Laser gain media consisting of dye-nanoparticle composites can improve the efficiency by lowering the lasing threshold and enhancing the photostability. The electric field confined near the surface of metal nanoparticles due to Localized Surface Plasmon Resonance can be very effective for the excitation of active centers to impart high optical gain for lasing. Since the Surface Plasmon Resonance of nanoparticles of gold and silver lies in the visible range, it can affect the spectral emission characteristics of organic dyes such as Rhodamine6G through plasmon field generated by the particles. The change in emission of the dye placed near metal nanoparticles depend on plasmon field strength which in turn depends on the type of metal, size of nanoparticle, surface modification of the particle and the wavelength of incident light. Progress in fabrication of different types of nanostructures lead to the advent of nanospheres, nanoalloys, core-shell and nanowires to name a few. The thesis deals with the fabrication and characterisation of polymer optical fibers with various metallic and bimetallic nanostructures incorporated in the gain media for efficient fiber lasers with low threshold and improved photostability.