Synergism of Xanthate/Dithiocarbamate Accelerator in Carbon Black Filled NR Compounds

Zinc salts of ethyl, isopropyl and butyl xanthates were prepared in the laboratory. The effect of these xanthates with zinc diethyldithiocarbamate (ZDC) on the vulcanization of HAF filled NR compound has been studied at different temperatures. The rubber compounds with the three xanthate accelerators and ZDC were cured at various temperatures from 60°C to 150°C. The sheets were moulded and properties such as tensile strength , tear strength , cross-link density, elongation -at-break, compression set, heat build up, abrasion resistance, flex resistance , etc. were evaluated . The properties showed that zinc xanthate/ZDC accelerator combination has a positive synergistic effect on the mechanical properties of NR compounds. The curing of HAF filled NR compound containing zinc xanthate /ZDC is slightly slower than the curing of the corresponding gum compounds . It is observed that, by gradually increasing the amount of the accelerator, the cure time of black filled NR compound can be made equal to that of the gum compou

Xanthate Accelerators for Low Temperature Curing of Natural Rubber

ABSTRACT: Zinc salts of ethyl, isopropyl, and butyl xanthates were prepared in the laboratory. They were purified by reprecipitation and were characterized by IR, NMR, and thermogravimetric analysis techniques. The melting points were also determined. The rubber compounds with different xanthate accelerators were cured at temperatures from 30 to 150°C. The sheets were molded and properties such as tensile strength, tear strength, crosslink density, elongation at break, and modulus at 300% elongation were evaluated. The properties showed that all three xanthate accelerators are effective for room temperature curing.

Toxicity of Effluent from a Titanium Dioxide Factory on some Marine Animals

Toxicity of effluent from a titanium dioxide factory containing sulphuric acid residue with soluble iron metallic salts and insoluble material such as silica, etc. on fishes, decapods and molluscs was studied. The effluent caused changes in pH and oxygen depletion of the sea water. Sublethal effects of the precipitate of ferrous salts were also studied. Dilutions of effluent up to 1:150 were LC100 for all organisms used while 1:200 dilution was LC50 for fishes at 36 hr and for other organisms at 48 hr. But death of organisms at this concentration was caused by pH changes and oxygen depletion and did not account for the effects of the precipitate. Below this level precipitation started soon after mixing with sea water causing death of organisms by choking their gills and siphons. Dilutions,< 1:1000 were 96 hr LCO.

Fabrication and Characterization of All-Fiber Components for Optical Access Networks

This Thesis deals with the fabrication and characterization of novel all-fiber components for access networks. All fiber components offer distinctive advantages due to low forward and backward losses, epoxy free optical path and high power handling. A novel fabrication method for monolithic 1x4 couplers, which are vital components in distributed passive optical networks, is realized. The fabrication method differs from conventional structures with a symmetric coupling profile and hence offers ultra wideband performance and easy process control. New structure for 1x4 couplers, by fusing five fibers is proposed to achieve high uniformity, which gives equivalent uniformity performance to 1x4 planar lightwave splitters, isolation in fused fiber WDM is improved with integration of long period gratings. Packaging techniques of fused couplers are analyzed for long term stability.

Engineering the Properties of Indium Sulfide for Thin Film Solar Cells by Doping

In the present work, structural, optical and electrical properties of indium sulfide are tuned by specific and controlled doping. Silver, tin, copper and chlorine were used as the doping elements. In2S3 thin films for the present study were prepared using a simple and low cost “Chemical Spray Pyrolysis (CSP)” technique. This technique is adaptable for large-area deposition of thin films in any required shape and facilitates easiness of doping and/or variation of atomic ratio. It involves spraying a solution, usually aqueous, containing soluble salts of the constituents of the desired compound onto a heated substrate. Doping process was optimized for different doping concentrations. On optimizing doping conditions, we tuned the structural, optical and electrical properties of indium sulfide thin films making them perform as an ideal buffer layer.

Laser induced surface damage, thermal transport and microhardness studies on certain organic and semiorganic nonlinear optical crystals

N-alkyl-2,6-dimethyl-4(1H)-pyridinones, salts of 4-dimethylaminopyridine and 2-amino-5-nitropyridine are considered to be potential candidates for nonlinear optical (NLO) applications, in particular for the generation of blue-green laser radiation. Single crystals were grown following the slow evaporation technique at constant temperature. Single-shot laserinduced surface damage thresholds in the range 3–10 GW/cm2 were measured using a 18 ns Q-switched Nd:YAG laser. The surface morphologies of the damaged crystals were examined under an optical microscope and the nature of damage identified. The Vicker’s microhardness was determined at a load of 98.07 mN. The thermal transport properties, thermal diffusivity (α), thermal effusivity (e), thermal conductivity (K) and heat capacity (Cp), of the grown crystals were measured by an improved photopyroelectric technique at room temperature. All the results are presented and discussed.

Optimization of carbon and nitrogen sources and growth factors for the production of an aquaculture probiotic (Pseudomonas MCCB 103) using response surface methodology

Aim: To develop a new medium for enhanced production of biomass of an aquaculture probiotic Pseudomonas MCCB 103 and its antagonistic phenazine compound, pyocyanin. Methods and Results: Carbon and nitrogen sources and growth factors, such as amino acids and vitamins, were screened initially in a mineral medium for the biomass and antagonistic compound of Pseudomonas MCCB 103. The selected ingredients were further optimized using a full-factorial central composite design of the response surface methodology. The medium optimized as per the model for biomass contained mannitol (20 g l)1), glycerol (20 g l)1), sodium chloride (5 g l)1), urea (3Æ3 g l)1) and mineral salts solution (20 ml l)1), and the one optimized for the antagonistic compound contained mannitol (2 g l)1), glycerol (20 g l)1), sodium chloride (5Æ1 g l)1), urea (3Æ6 g l)1) and mineral salts solution (20 ml l)1). Subsequently, the model was validated experimentally with a biomass increase by 19% and fivefold increase of the antagonistic compound. Conclusion: Significant increase in the biomass and antagonistic compound production could be obtained in the new media. Significance and Impact of the Study: Media formulation and optimization are the primary steps involved in bioprocess technology, an attempt not made so far in the production of aquaculture probiotics.

Thermodynamics of transfer of polar nonelectrolytes from water to aqueous salt solutions

The Setschenow parameter and thermodynamic parameters of transfer of a number of monosubstituted benzoic acids from water to different salt solutions have been reported. The data have been rationalized by considering the structure breaking effects of the ions of the salts, the localised hydrolysis model, the internal pressure theory and Symons' theory of water structure.

Solubility of 4-Nitrobenzoic Acid in Water & Salt Solutions

Solubilities of 4-nitrobenzoic acid at 25°, 35° and 42°C have been determined in water and in the presence of several concentrations of electrolytes. The free energies, enthalpies and entropies of transfer are also reported. The data have been rationalized by considering the structure-breaking effects of the ions of the salts and the requirement of the localized hydrolysis model. The theory of Symons is not satisfactory to rationalise the experimental data.

Salting Coefficients of Fluorobenzoic Acids

The Setschenow parameter and thermodynamic parameters of transfer of 2-, 3- and 4-fluorobenzoic acid from water to salt solution are reported. The data have been rationalized by considering the structure breaking effects of the ions of the salts, the localized hydrolysis model and the internal pressure theory.

Salting coefficient of hydroxybenzoic acids

The Setschenow parameter and thermodynamic parameters of transfer of 2- and 4- hydroxybenzoic acids from water to salt solutions have been reported. The data have been rationalised by considering the structure breaking effects of the ions of the salts, the localized hydrolysis model, the internal pressure theory and the theory of water structure due to Symons.

Salting Coefficients of 2-, 3-, and 4-Methylbenzoic Acids

The Setschenow parameter and thermodynamic parameters of transfer of 2-, 3-, and 4-methylbenzoic acids from water to salt solutions have been reported. The data have been rationalized by considering the structure breaking effects of the ions of the salts, the localized hydrolysis model, and the internal pressure theory.

Thermodynamics of Transfer of Aminobenzoic Acids from Water to Aqueous Salt Solutions

The Setschenow parameter and thermodynamic parameters of transfer of 2- and 4-aminobenzoic acids from water to salt solutions have been reported. The results are discussed in terms of the structure- breaking effects of the ions of the salts, the localized hydrolysis model, and the internal pressure theory.

Effect of dissolved NaCl, MgCl2, and Na2SO4 in seawater on the optical attenuation in the region from 430 to 630 nm

The split-pulse laser method is used to reinvestigate the optical attenuation of distilled water in the region from 430 to 630 nm. The studies are then extended to ionic solutions of NaCl, MgCl2, and Na2SO4, these salts forming the major constituents of seawater. The effect of the concentration of these constituents on optical attenuation is investigated. Further, optical attenuation studies are carried out for the region from 430 to 630 nm for an aqueous solution prepared with all the major constituents in the same proportions as in natural seawater. These values are then compared with values obtained for natural seawater. The relative role of dissolved salts and suspended particles on optical attenuation in seawater is discussed. The lowest attenuation is observed at ~450 nm for all solutions and is found to coincide with that for distilled water.

Global Value Chain Linkages of Manufacturing Export Firms: A Study of The Kannur Home Textile Industry

The literature on the involvement of developing countries in trade has focused on the effects of different aspects of globalization on firms, regions and countries. The study attempts to examine how an export based industry, locallyembedded and originated on the basis of regional strengths has been inserted into the global trade framework. Though the unit of analysis is the manufacturing export firm in the region of Kannur, it represents the entire home textile export industry from the state of Kerala, as close to 90% of fabric exports in home furnishing material, textiles for upholstery and decoration and stitched or fused, and branded made ups are from the region. From a global perspective, how developing countries face newer trade restrictions and overcome non quota barriers by firm and region specific activities within a value chain framework is a major research area, which has already contributions from the Ludhiana woolen cluster (Tewari,1999 ) and the Tirupur cluster in India (Cawthorne, 1995). The study contributes to the value chain literature by examining the governance and upgrading as well as how firms benefit from linkages. India has a number of export oriented agglomerations or regions where firms have been serving export markets for many years. In many cases it is no longer the supply side policy actions that determine how they are able to penetrate new markets or expand existing market share. Based on this study it becomes possible to understand how the global value chain operates in these different industries to examine whether there is a danger of immiserisation of growth or low road growth