11 resultados para Qu, Yuan, approximately 343 B.C.-approximately 277 B.C.
em Brock University, Canada
Resumo:
Modifications to the commercial hydride generator, manufactured by Spectrametrics, resulted in improved operating procedure and enhancement of the arsenic and germanium signals. Experiments with arsenic(III) and arsenic(V) showed that identical reiults could be produced from both oxidation states. However, since arsenic(V) is reduced more slowly than arsenic(III), peak areas and not peak heights must be measured when the arsine is immediately stripped from the system (approximately 5 seconds reaction). When the reduction is allowed to proceed for 20 seconds before the arsine is stripped, peak heights may be used. For a 200 ng/mL solution, the relative standard deviation is 2.8% for As(III) and 3.8% for As(V). The detection limit for arsenic using the modified system is 0.50 ng/mL. Studies performed on As(V) standards show that the interferences from 1000 mg/L of nickel(II), cobalt(II), iron(III), copper(II), cadmium(II), and zinc(II) can be eliminated with the aid of 5 M Hel and 3% L-cystine. Conditions for the reduction of germanium to the corresponding hydride were investigated. The effect of different concentrations of HCl on the reduction of germanium to the covalent hydride in aqueous media by means of NaBH 4 solutions was assessed. Results show that the best response is accomplished at a pH of 1.7. The use of buffer solutions was similarly characterized. In both cases, results showed that the element is best reduced when the final pH of the solution after reaction is almost neutral. In addition, a more sensitive method, which includes the use of (NH4)2S208' has been developed. A 20% increase in the germanium signal is registered when compared to the signal achieved with Hel alone. Moreover, under these conditions, reduction of germanium could be accomplished, even when the solution's pH is neutral. For a 100 ng/mL germanium standard the rsd is 3%. The detection limit for germanium in 0.05 M Hel medium (pH 1.7) is 0.10 ng/mL and 0.09 ng/mL when ammonium persulphate is used in conjunction with Hel. Interferences from 1000 mg/L of iron(III), copper(II), cobalt(II), nickel(II), cadmium(II), lead(II), mercury(II), aluminum(III), tin(IV), arsenic(III), arsenic(V) and zinc(II) were studied and characterized. In this regard, the use of (NH4)ZS20S and Hel at a pH of 1.7 proved to be a successful mixture in the sbppression of the interferences caused by iron, copper, aluminum, tin, lead, and arsenic. The method was applied to the determination of germanium in cherts and iron ores. In addition, experiments with tin(IV) showed that a 15% increase in the tin signal can be accomplished in the presence of 1 mL of (NH4)2S20S 10% (m/V).
Resumo:
A method using L-cysteine for the determination of arsenous acid (As(III)), arsenic acid (As(V)), monomethylarsonic acid (MMAA), and dimethylarsinic acid (DMAA) by hydride generation was demonstrated. The instrument used was a d.c. plasma atomic emission spectrometer (OCP-AES). Complete recovery was reported for As(III), As(V), and DMAA while 86% recovery was reported for MMAA. Detection limits were determined, as arsenic for the species listed previously, to be 1.2, 0.8, 1.1, and 1.0 ngemL-l, respectively. Precision values, at 50 ngemL-1 arsenic concentration, were f.80/0, 2.50/0, 2.6% and 2.6% relative standard deviation, respectively. The L-cysteine reagent was compared directly with the conventional hydride generation technique which uses a potassium iodide-hydrochloric acid medium. Recoveries using L-cysteine when compared with the conventional method provided the following results: similar recoveries were obtained for As(III), slightly better recoveries were obtained for As(V) and MMAA, and significantly better recoveries for DMAA. In addition, tall and sharp peak shapes were observed for all four species when using L-cysteine. The arsenic speciation method involved separation by ion exchange .. high perfonnance liquid chromatography (HPLC) with on-line hydride generation using the L.. cysteine reagent and measurement byOCP-AES. Total analysis time per sample was 12 min while the time between the start of subsequent runs was approximately 20 min. A binary . gradient elution program, which incorporated the following two eluents: 0.01 and 0.5 mM tri.. sodium citrate both containing 5% methanol (v/v) and both at a pH of approximately 9, was used during the separation by HPLC. Recoveries of the four species which were measured as peak area, and were normalized against As(III), were 880/0, 290/0, and 40% for DMAA, MMAA and As(V), respectively. Resolution factors between adjacent analyte peaks of As(III) and DMAA was 1.1; DMAA and MMAA was 1.3; and MMAA and As(V) was 8.6. During the arsenic speciation study, signals from the d.c. plasma optical system were measured using a new photon-signal integrating device. The_new photon integrator developed and built in this laboratory was based on a previously published design which was further modified to reflect current available hardware. This photon integrator was interfaced to a personal computer through an AID convertor. The .photon integrator has adjustable threshold settings and an adjustable post-gain device.
Resumo:
Presence of surface glycoprotein in Piptocephalis virginiana that recognizes the host glycoproteins band c, reported earlier from our laboratory, was detected by immunofluorescence microscopy. Germinated spores of P. virginiana treated with Mortierella pusilla cell wall protein extract, primary antibodies prepared against glycoproteins band c and FITC-goat anti-rabbit IgG conjugate showed fluorescence. This indicated that on the surfaces of the biotrophic mycoparasite P. virginiana , there might be a complementary molecule which recognizes the glycoproteins band c from M. pusilla. Immunobinding analysis identified a glycoprotein of Mr 100 kDa from the mycoparasite which binds with the host glycoproteins band c, separately as well as collectively. Purification of this glycoprotein was achieved by (i) 60% ammonium sulfate precipitation, (ii) followed by heat treatment, and (iii) Sephadex G-IOO gel filtration. The glycoprotein was isolated by preparative polyacrylamide gel electrophoresis by cutting and elution. The purity of the protein ·was ascertained by SDS-PAGE and Western blot analysis. Positive reaction to periodic acid-Schiff reagent revealed the glycoprotein nature of this 100 kDa protein. Mannose was identified as a major sugar component of this glycoprotein by using a BoehringerMannheim Glycan Differentiation Kit. Electrophoretically purified glycoprotein was used to raIse polyclonal antibody in rabbit. The specificity of the antibody was determined by dot-immunobinding test and western-blot analysis. Immunofluorescence mIcroscopy revealed surface localization of the protein on the germ tube of Piptocephalis virginiana. Fluorescence was also observed at the surfaceJ of the germinated spores and hyphae of the host, M. pusilla after treatment with complementary protein from P. virginiana, primary antibody prepared against the complementary protein and FITC-goat anti-rabbit IgG conjugate.
Resumo:
Cytochrome c oxidase .inserted into proteoliposomes translocates protons with a stoichiometry of approx-, imately 0.4-0.6 H+/e- in the presence of valinomycin plus pottasium. The existance .ofsuchproton translocation is .supportedby experiments with lauryl maltoside which abolished the pulses but~~d not inhibit cyt. c binding .or oxidase turnover. Pulses with K3FeCN6 did not induce acidification further supporting vectorial proton transport by cyt ..aa3 . Upon lowering the ionic strength and pulsing with ferrocytochrome c, H+/eratios increased. This increase is attributed to scaler proton release consequent upon cyt.c-phospholipid binding. Oxygen pulses at low ionic strength however did not exhibit this large scaler increase in H+/e- ratios.A-small increase was observed upon .02 pul'sing at·low ionic strengt.h. This increase was KeN and, ,pcep sensitive and thus possibly due to a redox linked scaler deprotonation. Increases in the H+/e- ratio also occurred ifp~lses ,were performed in the presence of nonactin rather.than valinomycin. The fluorescent pH indicator pyranine was internally trapped inaa3 conta~ning "proteoliposomes. Internal alkalinization, as mon,itored by pyranine fluorescence leads to a of approx.imately 0.35 units, which is proportional to electron flux. This internal alkalinization was also DCCD sensitive, being inhibited by approximately 50%. This 50% inhibition of internal alkalinization supports the existance of vectorial proton transport.
Resumo:
This study was undertaken to investigate any textual differences and similarities within essays written with a word processing program and an e-mail editor by non-native writers. It arose from many contradictions and a paucity of empirical research within the field of second language learning and electronic technology. To further explore these contradictory observations, 3 classes of intermediate level ESL (English as a Second Language) students v^ote 6 essays, alternating between a word processing program and an e-mail editor. Prior to the data collection, students read brief texts and responded to questions that focused upon three formal topics: immigration, economics, and multiculturalism. Data were examined for (a) the differences in the frequency counts of 12 cohesive devices, (b) sentence complexity, which focused upon the occurrences of simple and complex sentences, (c) the number of words within the writings, (d) the method of contextualization preferred by writers, and (e) any variations in the final grades of the students' texts that resulted from holistic rating. Results of analysis indicated that there were no statistically significant differences in the frequency counts of the linguistic features. Sentence complexity did not vary within the off-line and on-line essays. The average number of words found within the off-line essays was approximately 20% greater than within on-line essays. Contextualization methods were not different within word-processed or e-mailed essays. Finally, there was no difference in the quality of the texts when holistically rated.
Resumo:
It has previously been recognized that the major biochemical toxicity induced by sulphide is due to an inhibition of cytochrome ~ oxidase. Inhibition of this enzyme occurs at 30°C and pH 7.4 with a Ki of approximately 0.2 ~M, and a kon of 104 M-1 s-l, under catalytic conditions. However, the equimo1ar mixture of sulphide and the enzyme shows identical catalytic behaviour to that of the native enzyme. This cannot readily be attributed to rapid dissociation of sulphide, as both spectroscopic and plot analysis indicate the koff value is low. The addition of stoichiometric sulphide to the resting oxidized enzyme gives rise to the appearance of a low-spin ferric-type spectrum not identical with that seen on the addition of excess sulphide to the enzyme aerobically. Sulphide added to the enzyme anaerobically gives rise to another low-spin, probably largely ferric, form which upon admission of oxygen is then converted into a 607 nm species closely resembling Compound C. The 607 nm form is probably the precursor of oxyferricytochrome aa3. The addition of successive a1iquots of Na2S solution to the enzyme induces initial uptake of approximately 3 moles of oxygen per mole of the enzyme. Thus, it is concluded that: 1. the initial product of sulphide-cytochrome c oxidase interaction is not an inhibited form of the enzyme, but the low-spin (oxyferri) ~3+~+ species; 2. a subsequent step in which sulphide reduces cytochrome ~ occurs; 3. the final inhibitory step, in which a further molecule of sulphide binds to the cytochrome ~ iron centre in the cytochrome ~2+~+ species, gives the cytochrome a2+~+-H2S form which is a half-reduced fully inhibited species;4. a 607 run form of the enzyme is produced which may be converted into a catalytically active low-spin (oxyferri) state; and therefore 5. liganded sulphide may be able to reduce the cytochrome 33 -Cu centre without securing the prior reduction of the cytochrome a_ haem group or the Cud centre associated with it.
Resumo:
A blueprint produced by Westinghouse Electric & MFG. Co. in Pittsburgh, Pennsylvanna. The blueprint is dated 19 August 1903 and is stamped "OBSOLETE".
Resumo:
A letter from chief engineer C. Sellers to W. B. Rankine discussing the bid of I. P. Morris Co. Sellers discusses conversation with Mr. Hand of I.P. Morris.
Resumo:
(A) In recent years, considerable amount of effort has contributed towards enhancing our understanding of the new photoswitch, cyclic azobenzene, particularly from the theoretical point of view. However, the challenging part with this system was poor efficiency of its synthesis from 2,2’- dinitrodibenzyl and lack of effective methods for further modification which would be useful to incorporate this system into biomolecules as a photoswitch. We report the synthesis of cyclic azobenzene and analogues from 2,2’-dinitrodibenzyl, which would allow for further incorporation of this cyclic azobenzene into biomolecules. Reaction of 2,2’-dinitrodibenzyl with zinc metal powder in the presence of triethylammonium formate buffer (pH-9.5) gave a cyclic azoxybenzene, 11,12-dihydrodibenzo[c,g][1,2]diazocine-5-oxide. The latter compound was converted into cyclic azobenzene analogues (bromo-, chloro-, cyano-, and carboxyl) through subsequent transformations. The carboxylic acid analogue was reacted with D-threoninol to give the corresponding amide, which readily undergoes photo-isomerization upon illumination with light. Upon illumination with light at 400 nm, approximately 70% of cis- isomer of amide was isomerized to trans- isomer. It was observed that cis- to trans- isomerization reached the maximum steady state of light transmission after approximately 40 min, whereas the trans- to cis- isomerization approximately acquired in 2 h to regain full recovery of light transmission. Cyclic azobenzene phosphoramidite was synthesized from DMT-protected D-threoninol linked cyclic azobenzene. (B) In recent years, there has been considerable interest invested towards the synthesis of azobenzene analogues for incorporation into proteins. Among the many azobenzene analogues, the synthesis of bi-functional cyclic azobenzene analogues for the incorporation into proteins is relatively new. In this thesis, we report the synthesis of a cyclic azobenzene biscarboxylic acid from 4-(bromomethyl)benzonitrile. (C) Azobenzene has been widely used in the field of polymer science to study the surface morphology and surface properties of polymers. In this thesis, we report the incorporation of cyclic azobenzene into a commercial polymer 2- (hydroxyethyl)methacrylate. Samples collected after 24 h from the reaction solution showed approximately 9% of incorporation of cyclic azobenzene into polymer compared to samples collected after 10 h, which showed approximately 6% incorporation.
Resumo:
Letter to J. Bradley from B.C.A. Gogy in the Office of the Adjutant General of Militia, Montreal (1 page, printed) regarding Bradley’s desire to obtain commission as a captain in the Quebec Artillery, Aug. 25, 1845
Resumo:
Letter to J.P. Bradley from B.C.A. Gogy in the Office of the Adjutant General of Militia, Montreal regarding procedures for applying for a captain’s commission in the militia (2 ½ pages, handwritten), Dec. 23, 1845.