Structural analysis of the Paint Lake Deformation Zone, Northern Ontario /

The Paint Lake Deformation Zone (PLDZ), located within the Superior Province of Canada, demarcates a major structural and lithological break between the Onaman-Tashota Terrane to the north and the Beardmore-Geraldton Belt to the south. The PLDZ is an east-west trending lineament, approximately 50 km in length and up to 1 km in width, comprised of an early ductile component termed the Paint Lake Shear Zone and a late brittle component known as the Paint Lake Fault. Structures associated with PLDZ development including S-, C- and C'-fabrics, stretching lineations, slickensides, C-C' intersection lineations, Z-folds and kinkbands indicate that simple shear deformation dominated during a NW-SE compressional event. Movement along the PLDZ was in a dextral sense consisting of an early differential motion with southside- down and a later strike-slip motion. Although the locus of the PLDZ may in part be lithologically controlled, mylonitization which accompanied shear zone development is not dependent on the lithological type. Conglomerate, intermediate and mafic volcanic units exhibit similar mesoscopic and microscopic structures where transected by the PLDZ. Field mapping, supported by thin section analysis, defines five strain domains increasing in intensity of deformation from shear zone boundary to centre. A change in the dominant microstructural deformation mechanism from dislocation creep to diffusion creep is observed with increasing strain during mylonitization. C'-fabric development is temporally associated with this change. A decrease in the angular relationship between C- and C'-fabrics is observed upon attaining maximum strain intensity. Strain profiling of the PLDZ demonstrates the presence of an outer primary strain gradient which exhibits a simple profile and an inner secondary strain gradient which exhibits a more complex profile. Regionally metamorphosed lithologies of lower greenschist facies outside the PLDZ were subjected to retrograde metamorphism during deformation within the PLDZ.

The micromorphology of Paleoseismic soft sediment deformation structures in glacial deposits from three sample sites in Scotland /

The nature of this research is to investigate paleoseismic deformation of glacial soft sediments from three sampling sites throughout the Scottish Highlands; Arrat's Mills, Meikleour and Glen Roy. The paleoseismic evidence investigated in this research will provide a basis for applying criteria to soft sediment deformation structures, and the trigger mechanisms that create these structures. Micromorphology is the tool used in this to investigate paleoseismic deformation structures in thin section. Thin section analysis, (micromorphology) of glacial sediments from the three sampling sites is used to determine microscale evidence of past earthquakes that can be correlated to modem-day events and possibly lead to a better understanding of the impact of earthquakes throughout a range of sediment types. The significance of the three sampling locations is their proximity to two major active fault zones that cross Scotland. The fault zones are the Highland Boundary Fault and the Great Glen Fault, these two major faults that parallel each other and divide the country in half Sims (1975) used a set of seven criteria that identified soft sediment deformation structures created by a magnitude six earthquake in Cahfomia. Using criteria set forth by Sims (1975), the paleoseismic evidence can be correlated to the magnitude of the deformation structures found in the glacial sediments. This research determined that the microstructures at Arrat's Mill, Meikleour and Glen Roy are consistent with a seismically induced origin. It has also been demonstrated that, even without the presence of macrostructures, the use of micromorphology techniques in detecting such activity within sediments is of immense value.

STRUCTURAL ANALYSIS, LAYER THICKNESS MEASUREMENTS AND MINERALOGICAL INVESTIGATION OF THE LARGE INTERIOR LAYERED DEPOSIT WITHIN GANGES CHASMA, VALLES MARINERIS, MARS

The interior layered deposit (ILD) in Ganges Chasma, Valles Marineris, is a 4.25 km high mound that extends approximately 110 km from west to east. The deposition, deformation, and erosion history of the Ganges ILD records aids in identifying the processes that formed and shaped the Chasma. To interpret structural and geomorphic processes acting on the ILD, multiple layer attitudes and layer thickness transects were conducted on the Ganges ILD. Mineralogical data was analyzed to determine correlations between materials and landforms. Layer thickness measurements indicate that the majority of layers are between 0.5 m and 4 m throughout the ILD. Three major benches dominate the Ganges ILD. Layer thicknesses increase at the ILD benches, suggesting that the benches are formed from the gradual thickening of layers. This indicates that the benches are depositional features draping over basement topography. Layer attitudes indicate overall shallow dips generally confined to a North-South direction that locally appear to follow bench topography. Layering is disrupted on a scale of 40 m to 150 m in 12 separate locations throughout the ILD. In all locations, underlying layering is disturbed by overlying folded layers in a trough-like geometry. These features are interpreted to have formed as submarine channels in a lacustrine setting, subsequently infilled by sediments. Subsequently, the channels were eroded to the present topography, resulting in the thin, curved layering observed. Data cannot conclusively support one ILD formation hypothesis, but does indicate that the Ganges ILD postdates Chasma formation. The presence of water altered minerals, consistently thin layering, and layer orientations provide strong evidence that the ILD formed in a lacustrine setting.