Investigations into phosphorus removal by constructed wetlands : root bed media modifications /

A study has been conducted focusing on how the phosphorus renrx)val efficiency of a constructed wetland (CW) can be optimized through the selective enrichment of the substratum. Activated alumina and powdered iron were examined as possible enrichment compounds. Using packed glass column trials it was found that alumina was not suitable for the renx)val of ortho-phosphate from solution, while mixtures of powdered iron and quartz sand proved to be very efficient. The evaluation of iron/sand mixtures in CWs planted with cattails was performed in three stages; first using an indoor lab scale wetland, then an outdoor lab scale wetland, and finally in a small scale pilot project. For the lab scale tests, three basic configurations were evaluated: using the iron/sand as a pre-filter, in the root bed. and as a post filter. Primary lagoon effluent was applied to the test cells to simulate actual CW conditions, and the total phosphorus and iron concentrations of the influent and effluent were nfK)nitored. The pilot scale trials were limited to using only a post filter design, due to in-progress research at the pilot site. The lab scale tests achieved average renrK>val efficiencies greater than 91% for all indoor configurations, and greater than 97% for all outdoor configurations. The pilot scale tests had an average renK)val efficiency of 60%. This relatively low efficiency in the pilot scale can be attributed to the post filters being only one tenth the size of the lab scale test in terms of hydraulic loading (6 cm/day vs. 60 cm/day).

Investigations towards the synthesis of isotope labelled analogues of tocopherols and tocotrienols /

Vitamin E is considered as the most effective lipophilic chain breaking antioxidant. a-Tocopherol and its analogues have been studied thoroughly with regards to its biokinetics and bioavailabily. Deuterated tocopherols have been synthesized and utilized in such studies. Tocotrienols are arousing more and more interest because of their high efficiency as antioxidants. However, to date, there is no effective synthetic method reported for deuterated tocotrienols. This thesis is focused on the investigation of the synthetic methods of deuterated tocotrienols and their analogues: 5-trideuteromethyl-a-tocotrienol, 5- trideuteromethyl-p-tocotrienol, tocotrienol acetate, silyl tocotrienol ether, etc. Several synthetic procedures for the preparation of poly-deuterated tocopherols are known. Mainly the deuterium is introduced by use of labelled formaldehyde and deuterated hydrogen chloride under Lewis acid catalysis. However, these methods are not effective in tocotrienols due to exchange of protons for deuterium at other sites under the acidic conditions. We developed several different approaches to generate polydeuterated tocotrienols by using both morpholinomethylation followed by reduction with NaCNBDs as deuterated reducing reagents and transmetalation strategy. The 5-trideuteromethyl-a-tocotrienol was finally obtained in a satisfactory yield of 60%. In addition, this thesis also discussed the study of structural comparison and the chemical property difference of tocopherols and tocotrienols, which provides hints to explain the reactivity difference of them towards oxidation at the C3-C4 positions.Furthermore, the methodology of halogenation and dehydrohalogenation of tocotrienol was explored to prepare a hexaene tocotrienol derivative as a florescent reporter of tocopherol.

Investigations of 2-alkyl-3-methoxypyrazines in three ladybug species and wine /

Investigations of 2-alkyl-3-methoxypyrazines (2-isopropyl-3-methoxypyra2ine, 2- secbutyl-3-methoxypyrazine and 2-isobutyl-3-niethoxypyrazine) in ladybug species {Coleoptera: Coccinellidae) and wine samples have been conducted. Headspace sampling coupled with gas chromatography-mass spectrometry was used to determine amounts of 2-alkyl-3-methoxypyra2ines in the ladybug species. Hippodamia convergens had the highest amount of alkybnethoxypyrazines, followed by Harmoma axyridis and the least in Coccinella septempunctata. Using a solvent extraction method, the precoccinelline alkaloid was found present in Hippodamia convergens and Coccinella septempunctata but not Harmonia axyridis. Steam distillation followed by a soHd phase extraction method as a sample preparation technique, enhanced detection while the isotope dilution method afforded accurate quantitation of the alkyknethoxypyrazines in the wine samples. Both ladybug-tainted and commercial wine samples were found to contain the 2- alkyl-3-methoxypyrazines. Wine samples prepared in 2001 generally contained higher levels than the corresponding 2003 samples. Levels of the 2-alkyl-3-methoxypyrazines found in the commercial wines ranged from a minimum value of 6 ng/L to 260 ±10 ng/L. Analyses revealed that for both ladybug species and wine samples, the 2- isopropyl-3-methoxypyrazine had the highest concentration, followed by 2-isobutyl- 3-methoxypyrazine and the least being the 2-secbutyl-3-methoxypyrazine. Possible contamination of the wine samples by ladybugs is thoroughly discussed. Furthermore, attempts to remove or reduce the levels of the alkylmethoxypyrazines with molecularly imprinted polymers from wine samples are presented in detail.

Investigations into the extraction and the determination of polycyclic aromatic hydrocarbons (PAHs) from water by solid-phase extraction and capillary gas chromatography/ mass spectrometry

Factors affecting the detennination of PAHs by capillary GC/MS were studied. The effect of the initial column temperature and the injection solvent on the peak areas and heights of sixteen PAHs, considered as priority pollutants, USillg crosslinked methyl silicone (DB!) and 5% diphenyl, 94% dimethyl, 1% vinyl polysiloxane (DBS) columns was examined. The possibility of using high boiling point alcohols especially butanol, pentanol, cyclopentanol, and hexanol as injection solvents was investigated. Studies were carried out to optimize the initial column temperature for each of the alcohols. It was found that the optimum initial column temperature is dependent on the solvent employed. The peak areas and heights of the PAHs are enhanced when the initial column temperature is 10-20 c above the boiling point of the solvent using DB5 column, and the same or 10 C above the boiling point of the solvent using DB1 column. Comparing the peak signals of the PAHs using the alcohols, p-xylene, n-octane, and nonane as injection solvents, hexanol gave the greatest peak areas and heights of the PAHs particularly the late-eluted peaks. The detection limits were at low pg levels, ranging from 6.0 pg for fluorene t9 83.6 pg for benzo(a)pyrene. The effect of the initial column temperature on the peak shape and the separation efficiency of the PARs was also studied using DB1 and DB5 columns. Fronting or splitting of the peaks was obseIVed at very low initial column temperature. When high initial column temperature was used, tailing of the peaks appeared. Great difference between DB! and.DB5 columns in the range of the initial column temperature in which symmetrical.peaks of PAHs can be obtained is observed. Wider ranges were shown using DB5 column. Resolution of the closely-eluted PAHs was also affected by the initial column temperature depending on the stationary phase employed. In the case of DB5, only the earlyeluted PAHs were affected; whereas, with DB1, all PAHs were affected. An analytical procedure utilizing solid phase extraction with bonded phase silica (C8) cartridges combined with GC/MS was developed to analyze PAHs in water as an alternative method to those based on the extraction with organic solvent. This simple procedure involved passing a 50 ml of spiked water sample through C8 bonded phase silica cartridges at 10 ml/min, dried by passing a gentle flow of nitrogen at 20 ml/min for 30 sec, and eluting the trapped PAHs with 500 Jll of p-xylene at 0.3 ml/min. The recoveries of PAHs were greater than 80%, with less than 10% relative standard deviations of nine determinations. No major contaminants were present that could interfere with the recognition of PAHs. It was also found that these bonded phase silica cartridges can be re-used for the extraction of PAHs from water.

Investigations into the determinations of hydride-forming elements

Analytical methods for the determination of trace amounts of germanium, tin and arsenic were established using hydride generation coupled with direct current plasma atomic emission spectrometry. A continuous gas flowing batch system for the hydride generation was investigated and was applied to the determination of germanium(Ge), tin(Sn), antimony(Sb) and lead(Pb) (Preliminary results suggest that it is also applicable to arsenic)As) ). With this system, the reproducibility of signals was improved and the determination was speeded up, compared with the conventional batch type hydride generation system. Each determination was complete within one minute. Interferences from a number of transition metal ions, especially from Pd(II), Pt(IV), Ni(II), Cu(II), Co(II), and Fe(II, III), have proven to be very serious under normal conditions, in the determination of germanium, tin, and arsenic. These interference effects were eliminated or significantly reduced in the presence of L-cystine or L-cysteine. Thus, a 10-1000 fold excess of Ni(II), Cu(II), Co(II), Fe(II), Pt(IV), Pd(II), etc. can be tolerated without interference, In the presence of L-cystine or L-cysteine, compared with absence of interference reducing agent. The methods for the determination of Ge, Sn, and As were examined by the analyses of standard reference materials. Interference effects from the sample matrix, for example, in transition metal-rich samples, copper, iron and steel, were eliminated by L-cystine (for As and Sn) and by LI cysteine (for Ge). The analysis of a number of standard reference materials gave excellent results of As and Sn contents in agreement with the certified values, showing there was no systematic interference. The detection limits for both germanium and tin were 20 pg ml- I . Preliminary studies were carried out for the determination of antimony and lead. Antimony was found to react with NaBH4, remaInIng from the previous determinations, giving an analytical signal. A reversed injection manner, i.e., injection of the NaBH4 solution prior to the analyte solution was used to avoid uncertainty caused by residual NaBH4 present and to ensure that an excess of NaB H4 was available. A solution of 0.4% L-cysteine was found to reduce the interference from selected transition metal ions, Co(II), Cu(II), Ni(II) and Pt(IV). Hydrochloric acid - hydrogen peroxide, nitric acid - ammonium persulphate, and potassium dichromate malic acid reaction systems for lead hydride generation were compared. The potassium dichromate - malic acid reaction medium proved to be the best with respect to reproducibility and minimal interference. Cu(II), Ni(II), and Fe(II) caused strong interference In lead determinations, which was not reduced by L-cysteine or Lcystine. Sodium citrate, ascorbic acid, dithizone, thiosemicarbazide and penicillamine reduced interferences to some extent. Further interference reduction studies were carried out uSIng a number of amino acids, glycine, alanine, valine, leucine and histidine, as possible interference reducing agents in the determination of germanium. From glycine, alanine, valine to leucine, the interference reduction effect in germanium determinations decreased. Histidine II was found to be very promising In the reduction of interference. In fact, histidine proved more efficient than L-cystine and L-cysteine In the reduction of interference from Ni(II) in the determination of germanium. Signal enhancement by easily ionized elements (EIEs), usually regarded as an interference effect in analysis by DCP-AES, was studied and successfully applied to advantage in improving the sensitivity and detection limit in the determination of As, Ge, Sn, Sb, and Pb. The effect of alkali and alkaline-earth elements on the determination of the above five hydride forming elements was studied. With the appropriate EIE, a signal enhancement of 40-115% was achieved. Linear calibration and good reproducibility were also obtained in the presence of EIEs. III

Investigations on the production of long chain fatty acids in Choanephora cucurbitarum (Berk. & Rav.) Thaxte

Thesis (M.Sc.)--Brock University, 1979.

The determination of sinigrin in Brassica, and investigations into the use of allyl-isothiocyanate as a nematicide

The goal of this thesis was to study factors related to the development of Brassica juncea as a sustainable nematicide. Brassica juncea is characterized by the glycoside (glucosinolate) sinigrin. Various methods were developed for the determination of sinigrin in Brassica juncea tissue extracts. Sinigrin concentrations in plant tissues at various stages of growth were monitored. Sinigrin enzymatically breaks down into allylisothiocyanate (AITC). AITC is unstable in aqueous solution and degradation was studied in water and in soil. Finally, the toxicity of AITC against the root-lesion nematode (Pratylenchus penetrans) was determined. A method was developed to extract sinigrin from whole Brassica j uncea tissues. The optimal time of extraction wi th boiling phosphate buffer (0.7mM, pH=6.38) and methanol/water (70:30 v/v) solutions were both 25 minutes. Methanol/water extracted 13% greater amount of sinigrin than phosphate buffer solution. Degradation of sinigrin in boiling phosphate buffer solution (0.13%/minute) was similar to the loss of sinigrin during the extraction procedure. The loss of sinigrin from boiling methanol/water was estimated to be O.Ol%/minute. Brassica juncea extract clean up was accomplished by an ion-pair solid phase extraction (SPE) method. The recovery of sinigrin was 92.6% and coextractive impurities were not detected in the cleaned up extract. Several high performance liquid chromatography (HPLC) methods were developed for the determination of sinigrin. All the developed methods employed an isocratic mobile phase system wi th a low concentration of phosphate buffer solution, ammonium acetate solution or an ion-pair reagent solution. A step gradient system was also developed. The method involved preconditioning the analytical column with phosphate buffer solution and then switching the mobile phase to 100% water after sample injection.Sinigrin and benzyl-glucosinolate were both studied by HPLC particle beam negative chemical ionization mass spectrometry (HPLCPB- NCI-MS). Comparison of the mass spectra revealed the presence of fragments arising from the ~hioglucose moiety and glucosinolate side-chain. Variation in the slnlgrin concentration within Brassica juncea plants was studied (Domo and Cutlass cuItivars). The sinigrin concentration in the top three leaves was studied during growth of each cultivar. For Cutlass, the minimum (200~100~g/g) and maximum (1300~200~g/g) concentrations were observed at the third and seventh week after planting, respectively. For Domo, the minimum (190~70~g/g) and maximum (1100~400~g/g) concentrations were observed at the fourth and eighth week after planting, respectively. The highest sinigrin concentration was observed in flower tissues 2050±90~g/g and 2300±100~g/g for Cutlass and Domo cultivars, respectively. Physical properties of AITC were studied. The solubility of AITC in water was determined to be approximately 1290~g/ml at 24°C. An HPLC method was developed for the separation of degradation compounds from aqueous AITC sample solutions. Some of the degradation compounds identified have not been reported in the literature: allyl-thiourea, allyl-thiocyanate and diallyl-sulfide. In water, AITC degradation to' diallyl-thiourea was favored at basic pH (9.07) and degradation to diallyl-sulfide was favored at acidic pH (4 . 97). It wap necessary to amend the aqueous AITC sample solution with acetonitrile ?efore injection into the HPLC system. The acetonitrile amendment considerably improved AITC recovery and the reproducibility of the results. The half-life of aqueous AITC degradation at room temperature did not follow first-order kinetics. Beginning with a 1084~g/ml solution, the half-life was 633 hours. Wi th an ini tial AITC concentration of 335~g/ml the half-life was 865 hours. At 35°C the half-life AITC was 76+4 hours essentially independent of the iiisolution pH over the range of pH=4.97 to 9.07 (1000~g/ml). AITC degradation was also studied in soil at 35°C; after 24 hours approximately 75% of the initial AITC addition was unrecoverable by water extraction. The ECso of aqueous AITC against the root-lesion nematode (Pratylenchus penetrans) was determined to be approximately 20~g/ml at one hour exposure of the nematode to the test solution. The toxicological study was also performed with a myrosinase treated Brassica juncea extract. Myrosinase treatment of the Brassica juncea extract gave nearly quantitative conversion of sinigrin into AITC. The myrosinase treated extract was of the same efficacy as an aqueous AITC solution of equivalent concentration. The work of this thesis was focused upon understanding parameters relevant to the development of Brassica juncea as a sustainable nematicide. The broad range of experiments were undertaken in support of a research priority at Agriculture and Agri-Food Canada.

Investigations on the host-parasite interface of a mycoparasite system /

The cell wall composition of Choanephora cucur - bitarum and the host-parasite interface, after infection with Piptocephalis virginiana , were examined in detail. The cell walls of C_. cucurbitarum were determined to be composed of chitin (17%), chitosan (28.4%), neutral sugars (7.2%),uronic acid (2.4%), proteins (8.2%) and lipids (13.8%). The structure of hyphal walls investigated by electron microscopy of shadowed replicas before and after alkali-acid hydrolysis, showed two distinct regions: microfibrillar and amorphous. The microfibrils which were composed of mainly chitin, were organized into two distinct layers: an outer, thicker layer of randomly orientated microfibrils and an inner, thin layer of parallel microfibrils.Electronmicrographs of the host-parasite interface of C_. cucurbitarum and the mycoparasite , P_. virginiana , 30 h following inoculation, showed that the sheath zone has a similar electron density to that of the host cell wall. The sheath was not present around the young (18 h old) haustorium. High-resolution autoradiographs of infected host hyphae showed that radioactive N-acetyl-D-glucosamine , a precursor of chitin, was incorporated preferentially in the host cell wall and sheath zone. Cell fractionation of label fed hyphae showed that 84% of the label was present in the cell wall and specifically in the chitin portion of the wall. The antifungal antibiotic, Polyoxin D, a specific inhibitor of the enzyme, chitin synthetase, suppressed the incorporation of the label in the cell wall and sheath zone and resulted in a decrease in electron density of the developing sheath. The significance of these results is discussed in the light of host resistance.

Biochemical and histological investigations of viral localisation in the hypersensitive reaction of Phaselous vulgaris L. var Pinto to tobacco mosaic virus infection

STOBBS, Lorne,W ABSTRACT Biochemical and Histological Investigations of viral localisation in the hypersensitive reaction of Phaseolus vulgaris L. var Pinto to tobacco mosaic virus infection. The infection of Phaseolus vulgaris L. var Pinto with tobacco mosaic virus (TMV) results in the production of distinct necrotic lesions confining the virus to restricted areas of the leaf surface. Biochemical and histological changes in the leaf tissue as a result of infection have been described. Trace accumulations of fluorescent metabolites, detected prior to lesion expression represent metabolites produced, by the cell in response to virus infection. These substances, are considered to undergo oxidation and in diffusing into adjacent cells, react with cellular constituents causing the death of these cells. Such cellular necrosis in advance of infection effectively limits virus spread. Chromatographic studies on extracts from TMV infected Pinto bean leaf tissue suggests that a number of extra-fluorescent metabolites produced on lesion'expression represent end products of phenolic oxidation r,eactionsoccurring earlier in these cells. Inhibition of phenolic oxidation by ascorbate infiltration or elevated temperature treatment resulted in the absence of extra-fluorescent metabolites and the continued movement of virus in the absence of necrosis. Further studies with i ascorbate infiltration indicated that irreversible necrotic events were determined as early as 12 tci 18 hrs after viral inoculation. Histochemical tests indicated that callose formation was initiated at this time, and occurred in response to necrotisation. Inhibition of necrosis by either ascorbate infiltration or elevated temp8rature treatment resulted in the absence of callose deposition. Scanning electron'micrographs of infected tissue revealed severe epidermal and palisade cell damage. Histochemical tests indicated extensive callose formation in cells bordering the lesion, and suggested the role of callose iTh the blockage of intercellular connections limiting virus movement. The significance of these cellular changes is discussed. ii

Investigations in flow injection analysis (FIA): conventional FIA determination of chloride in water; sequential injection (SI)-FIA determination of mercury in water

Flow injection analysis (FIA) was applied to the determination of both chloride ion and mercury in water. Conventional FIA was employed for the chloride study. Investigations of the Fe3 +/Hg(SCN)2/CI-,450 nm spectrophotometric system for chloride determination led to the discovery of an absorbance in the 250-260 nm region when Hg(SCN)2 and CI- are combined in solution, in the absence of iron(III). Employing an in-house FIA system, absorbance observed at 254 nm exhibited a linear relation from essentially 0 - 2000 Jlg ml- 1 injected chloride. This linear range spanning three orders of magnitude is superior to the Fe3+/Hg(SCN)2/CI- system currently employed by laboratories worldwide. The detection limit obtainable with the proposed method was determin~d to be 0.16 Jlg ml- 1 and the relative standard deviation was determined to be 3.5 % over the concentration range of 0-200 Jig ml- 1. Other halogen ions were found to interfere with chloride determination at 254 nm whereas cations did not interfere. This system was successfully applied to the determination of chloride ion in laboratory water. Sequential injection (SI)-FIA was employed for mercury determination in water with the PSA Galahad mercury amalgamation, and Merlin mercury fluorescence detection systems. Initial mercury in air determinations involved injections of mercury saturated air directly into the Galahad whereas mercury in water determinations involved solution delivery via peristaltic pump to a gas/liquid separator, after reduction by stannous chloride. A series of changes were made to the internal hardware and valving systems of the Galahad mercury preconcentrator. Sequential injection solution delivery replaced the continuous peristaltic pump system and computer control was implemented to control and integrate all aspects of solution delivery, sample preconcentration and signal processing. Detection limits currently obtainable with this system are 0.1 ng ml-1 HgO.

Landscape geochemical investigations in the vicinity of a lead deposit near Snertingdal, southern Norway

Landscape geochemical investigations were conducted upon portions of a natural uniform landscape in southern Norway. This consisted of sampling both soil profile samples and spruce tree twigs for the analysis of twelve chemical elements. These elements were cobalt, copper, nickel, lead, zinc, manganese, magnesium, iron, calcium, sodium, potassium and aluminum which were determined by atomic absorption analysis on standardized extraction techniques for both organic and inorganic materials. Two "landscape traverses" were chosen for a comparative study of the effects of varying landscape parameters upon the trace element distribution patterns throughout the landscape traverses. The object of this study was to test this method of investigation and the concept of an ideal uniform landscape under Norwegian conditions. A "control traverse" was established to represent uniform landscape conditions typical of the study area and was used to determine "normal" or average trace element distribution patterns. A "signal traverse" was selected nearby over an area of lead mineralization where the depth to bedrock is very small. The signal traverse provided an area of similar landscape conditions to those of the control traverse with significant differences in the bedrock configuration and composition. This study was also to determine the effect of the bedrock mineralization upon the distribution patterns of the twelve chemical elements within the major components of the two landscape traverses (i.e. soil profiles and tree branches). The lead distribution within the soils of the signal traverse showed localized accumulations of lead within the overburden with maximum values occurring within the organic A horizon of soil profile #10. Above average concentrations of lead were common within the signal traverse, however, the other elements studied were not significantly different from those averages determined throughout the soils of the control traverse. The spruce twig samples did not have corresponding accumulations of lead near the soil lead anomaly. This is attributable to the very localized nature of the lead dispersion pattern within the soils. This approach to the study of the geochemistry of a natural landscape was effective in establishing: a) average or "normal" trace element distribution patterns b) local variations in the landscape morphology and c) the effect of unusually high lead concentrations upon the geochemistry of the landscape (i.e. within the soil profiles and tree branches). This type of study provides the basis for further more intensive studies and serves only as a first approximation of the behaviour of elements within a natural landscape.

Investigations into the determination of polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs) by capillary gas chromatography

Factors involved in the determination of PAHs (16 priority PAHs as an example) and PCBs (10 PCB congeners, representing 10 isomeric groups) by capillary gas chromatography coupled with mass spectrometry (GC/MS, for PAHs) and electron capture detection (GC/ECD , for PCBs) were studied, with emphasis on the effect of solvent. Having various volatilities and different polarities, solvent studied included dichloromethane, acetonitrile, hexan e, cyclohexane, isooctane, octane, nonane, dodecane, benzene, toluene, p-xylene, o-xylene, and mesitylene. Temperatures of the capillary column, the injection port, the GC/MS interface, the flow rates of carrier gas and make-up gas, and the injection volume were optimized by one factor at a time method or simplex optimization method. Under the optimized conditions, both peak height and peak area of 16 PAHs, especially the late-eluting PAHs, were significantly enhanced (1 to 500 times) by using relatively higher boiling point solvents such as p-xylene and nonane, compared with commonly used solvents like benzene and isooctane. With the improved sensitivity, detection limits of between 4.4 pg for naphthalene and 30.8 pg for benzo[g,h,i]perylene were obtained when p-xylene was used as an injection solvent. Effect of solvent on peak shape and peak intensity were found to be greatly dependent on temperature parameters, especially the initial temperature of the capillary column. The relationship between initial temperature and shape of peaks from 16 PAHs and 10 PCBs were studied and compared when toluene, p-xylene, isooctane, and nonane were used as injection solvents. If a too low initial temperature was used, fronting or split of peaks was observed. On the other hand, peak tailing occurred at a too high initial column temperature. The optimum initial temperature, at which both peak fronting and tailing were avoided and symmetrical peaks were obtained, depended on both solvents and the stationary phase of the column used. On a methyl silicone column, the alkane solvents provided wider optimum ranges of initial temperature than aromatic solvents did, for achieving well-shaped symmetrical GC peaks. On a 5% diphenyl: 1% vinyl: 94% dimethyl polysiloxane column, when the aromatic solvents were used, the optimum initial temperature ranges for solutes to form symmetrical peaks were improved to a similar degree as those when the alkanes were used as injection solvents. A mechanism, based on the properties of and possible interactions among the analyte, the injection solvent, and the stationary phase of the capillary column, was proposed to explain these observations. The effect of initial temperature on peak height and peak area of the 16 PAHs and the 10 PCBs was also studied. The optimum initial temperature was found to be dependent on the physical properties of the solvent used and the amount of the solvent injected. Generally, from the boiling point of the solvent to 10 0C above its boiling point was an optimum range of initial temperature at which cthe highest peak height and peak area were obtained.

Investigations on the production of long chain fatty acids in Choanephora cucurbitarum (Berk.

The fatty acid composition of the total cellular lipids of Choanephora cucurbitarum incubated for 96 hrs on either glucose-ammonium sulfate or malt-weast extract media was determined. The major fatty acids were palmitic, palmitoleic, stearic and linoleic acids. The saturated fatty acid possessing the longest acyl chain was stearate (C 18:0). The presence of glutamic acid (2.0 x 10-1% or 1.36 x la-2M) in either of the above growth media resulted in increase in percent of 1f-linolenic acid, decrease in percent of linoleic ~iCid and appearance of a new series of fatty acid> C ~8 e.g. C ",,,,'V' C2k:O, C26,O. The addition of glutamic acid had no effect on the lipid yield but slightly decreased the degree of unsaturation. Compounds which duplicated the effect of glutamic acid were acetate, malate, citrate, succinate, 0( -ketoglutarate, prOline, -y -aminobutyric acid and glucose (3%) but not aspartic acid or alanine. ~o correlation was found between glutamic acid pool concentration and the presence in the growth medium of those compounds which stimulate long chain fatty acid production. Four hours of incubation with 27 JJ 1-1 glutamate supported the production of long chain fatty acids. This stimulation is inhibited if 272 .u M isophthalic acid is added with 27 AJ M glutamate. But, long chain fatty acids were detected when 27 JJ M eX -ketoglutarate is also present in the incubation mixture. Five hours of incubation with 100 ,Mg/ml of cycloheximide resulted in over 9CY/o inhibition of cytoplasmic :protein synthesise Glutamate (27 .uM) enhanced the synthesis of long chain fatty acids under these conditions. These findings are discussed in an attempt to provide a plausible explanation COmmon to compounds that support the production of long chain fatty acids.

Cryptic species status of Anopheles (Diptera: Culicidae) mosquitoes in Canada using a multidisciplinary approach

Many species of Anopheles mosquitoes (Diptera: Culicidae) are now recognized as species complexes whose members are often indistinguishable morphologically but identifiable based on ecological, genetic, or behavioural data. Because the members of species complexes often differ in their vector potential, accurate identification of vector species is essential for successful mosquito control. To investigate the cryptic species status of Anopheles mosquitoes in Canada, specimens were collected from across the country and examined using morphological, molecular, and ecological data. Six of the seven traditionally recognised species from Canada were collected from locations in British Columbia, Quebec, Newfoundland and Labrador, and throughout Ontario, including Anopheles barberi, An. earlei, An. freeborni, An. punctipennis, An. quadrimaculatus s.l., and An. walkeri. Variation in polymorphic traits within An. earlei, An. punctipennis, and An. quadrimaculatus s.l. were quantified and egg morphology examined using scanning electron microscopy. Morphological identification of adult and larval specimens suggested that two described cryptic species, An. perplexens and An. smaragdinus, were present in Canada. DNA sequence data were analysed for evidence of cryptic species using three molecular markers: COl, ITS2, and ITS!. Intraspecific COl variation was very low in most species «1 %), except for An. punctipennis with 2% sequence divergence between those from British Columbia (BC) and Ontario (ON), and An. walkeri with 7% sequence divergence between populations from Manitoulin Island (NO) and Long Point Provincial Park (LP). Similar patterns were also seen using ITS2 and ITS 1. Therefore, molecular data revealed the presence of two putative cryptic species within two species examined (i.e., An. walkeri and An. punctipennis), corresponding to collection location (i.e., NO vs. LP and BC vs. ON, respectively). Surprisingly, there was no molecular support for the presence of either An. perplexens or An. smaragdinus in Canada despite the morphological assessments. Ecological data from all collection sites were recorded and are available in an online database designed to manage all collection and identification data. Current bionomic information, including regional abundance, larval habitat, and species associations, was determined for each species. This multidisciplinary study of Anopheles mosquitoes is the first detailed investigation of these potential disease vectors in Canada and demonstrates the importance of an integrated approach to anopheline systematics that includes molecular data.

Electrophysiological investigations of the timing of face processing

As important social stimuli, faces playa critical role in our lives. Much of our interaction with other people depends on our ability to recognize faces accurately. It has been proposed that face processing consists of different stages and interacts with other systems (Bruce & Young, 1986). At a perceptual level, the initial two stages, namely structural encoding and face recognition, are particularly relevant and are the focus of this dissertation. Event-related potentials (ERPs) are averaged EEG signals time-locked to a particular event (such as the presentation of a face). With their excellent temporal resolution, ERPs can provide important timing information about neural processes. Previous research has identified several ERP components that are especially related to face processing, including the N 170, the P2 and the N250. Their nature with respect to the stages of face processing is still unclear, and is examined in Studies 1 and 2. In Study 1, participants made gender decisions on a large set of female faces interspersed with a few male faces. The ERP responses to facial characteristics of the female faces indicated that the N 170 amplitude from each side of the head was affected by information from eye region and by facial layout: the right N 170 was affected by eye color and by face width, while the left N 170 was affected by eye size and by the relation between the sizes of the top and bottom parts of a face. In contrast, the P100 and the N250 components were largely unaffected by facial characteristics. These results thus provided direct evidence for the link between the N 170 and structural encoding of faces. In Study 2, focusing on the face recognition stage, we manipulated face identity strength by morphing individual faces to an "average" face. Participants performed a face identification task. The effect of face identity strength was found on the late P2 and the N250 components: as identity strength decreased from an individual face to the "average" face, the late P2 increased and the N250 decreased. In contrast, the P100, the N170 and the early P2 components were not affected by face identity strength. These results suggest that face recognition occurs after 200 ms, but not earlier. Finally, because faces are often associated with social information, we investigated in Study 3 how group membership might affect ERP responses to faces. After participants learned in- and out-group memberships of the face stimuli based on arbitrarily assigned nationality and university affiliation, we found that the N170 latency differentiated in-group and out-group faces, taking longer to process the latter. In comparison, without group memberships, there was no difference in N170 latency among the faces. This dissertation provides evidence that at a neural level, structural encoding of faces, indexed by the N170, occurs within 200 ms. Face recognition, indexed by the late P2 and the N250, occurs shortly afterwards between 200 and 300 ms. Social cognitive factors can also influence face processing. The effect is already evident as early as 130-200 ms at the structural encoding stage.