Modeling and Synthesis of Tracking Control for the Belt Drive System

Usingof belt for high precision applications has become appropriate because of the rapid development in motor and drive technology as well as the implementation of timing belts in servo systems. Belt drive systems provide highspeed and acceleration, accurate and repeatable motion with high efficiency, long stroke lengths and low cost. Modeling of a linear belt-drive system and designing its position control are examined in this work. Friction phenomena and position dependent elasticity of the belt are analyzed. Computer simulated results show that the developed model is adequate. The PID control for accurate tracking control and accurate position control is designed and applied to the real test setup. Both the simulation and the experimental results demonstrate that the designed controller meets the specified performance specifications.

Centralized Motion Control of a Linear Tooth Belt Drive: Analysis of the Performance and Limitations

A centralized robust position control for an electrical driven tooth belt drive is designed in this doctoral thesis. Both a cascaded control structure and a PID based position controller are discussed. The performance and the limitations of the system are analyzed and design principles for the mechanical structure and the control design are given. These design principles are also suitable for most of the motion control applications, where mechanical resonance frequencies and control loop delays are present. One of the major challenges in the design of a controller for machinery applications is that the values of the parameters in the system model (parameter uncertainty) or the system model it self (non-parametric uncertainty) are seldom known accurately in advance. In this thesis a systematic analysis of the parameter uncertainty of the linear tooth beltdrive model is presented and the effect of the variation of a single parameter on the performance of the total system is shown. The total variation of the model parameters is taken into account in the control design phase using a Quantitative Feedback Theory (QFT). The thesis also introduces a new method to analyze reference feedforward controllers applying the QFT. The performance of the designed controllers is verified by experimentalmeasurements. The measurements confirm the control design principles that are given in this thesis.

Novel control, haptic and calibration methods for teleoperated electrohydraulic servo systems

The aim of this thesis is to propose a novel control method for teleoperated electrohydraulic servo systems that implements a reliable haptic sense between the human and manipulator interaction, and an ideal position control between the manipulator and the task environment interaction. The proposed method has the characteristics of a universal technique independent of the actual control algorithm and it can be applied with other suitable control methods as a real-time control strategy. The motivation to develop this control method is the necessity for a reliable real-time controller for teleoperated electrohydraulic servo systems that provides highly accurate position control based on joystick inputs with haptic capabilities. The contribution of the research is that the proposed control method combines a directed random search method and a real-time simulation to develop an intelligent controller in which each generation of parameters is tested on-line by the real-time simulator before being applied to the real process. The controller was evaluated on a hydraulic position servo system. The simulator of the hydraulic system was built based on Markov chain Monte Carlo (MCMC) method. A Particle Swarm Optimization algorithm combined with the foraging behavior of E. coli bacteria was utilized as the directed random search engine. The control strategy allows the operator to be plugged into the work environment dynamically and kinetically. This helps to ensure the system has haptic sense with high stability, without abstracting away the dynamics of the hydraulic system. The new control algorithm provides asymptotically exact tracking of both, the position and the contact force. In addition, this research proposes a novel method for re-calibration of multi-axis force/torque sensors. The method makes several improvements to traditional methods. It can be used without dismantling the sensor from its application and it requires smaller number of standard loads for calibration. It is also more cost efficient and faster in comparison to traditional calibration methods. The proposed method was developed in response to re-calibration issues with the force sensors utilized in teleoperated systems. The new approach aimed to avoid dismantling of the sensors from their applications for applying calibration. A major complication with many manipulators is the difficulty accessing them when they operate inside a non-accessible environment; especially if those environments are harsh; such as in radioactive areas. The proposed technique is based on design of experiment methodology. It has been successfully applied to different force/torque sensors and this research presents experimental validation of use of the calibration method with one of the force sensors which method has been applied to.

High Performance Electrical Drive System for a Biomechanical Test and Rehabilitation Equipment

Suunniteltiin ja rakennettiin suoraa vääntömomenttisäätöä soveltava taajuudenmuuttajakäyttö oikosulkumoottorin ohjaukseen korvaamaan passiivinen jarrukäyttö. Laite on kuntoutuslaite, jolla tehdään lihasvoiman mittauksia ja voimaharjoituksia. Selvitettiin kaupallisten moottoreiden ja taajuudenmuuttajien suoritusominaisuuksia ja tämän perusteella valittiin käyttöön sopivat laitteet. Työssä esitetään kaksi oikosulkumoottorin ohjaustapaa: vektorisäätö ja suora vääntömomenttisäätö. Merkittävin osa tästä työstä käsittelee - tarkan turvallisuussuunnitelman lisäksi - kuntoutuslaitteen prototyypin komponentteja, kokoamista ja suoritustestien tuloksia.

Lineaarisen hammashihnaservokäytön tilasäätö

Tuotantotehokkuus näyttelee yhä suurempaa roolia teollisuudessa, minkä vuoksi myös pakkauslinjas­toille joudutaan asettamaan suuria vaatimuksia. Usein leik­kaus- ja kappaleensiirtosovelluksissa käyte­tään lineaarisia ruuvikäyttöjä, jotka voitaisiin tietyin edellytyksin korvata halvemmilla ja osittain suori­tuskykyisimmillä hammashihnavetoisilla johteilla. Yleensä paikkasäädetty työsolu muodostuu kahden tai kolmen eri koordinaatisto­akselin suuntaan asen­netuista johteista. Tällaisen työsolun paikoitustarkkuuteen vaikuttavat muun muassa käytetty säätöra­kenne, moottorisäätöketjun viiveet, sekä laitteiston eri epälineaarisuudet, kuten kitka. Tässä työssä esitetään lineaarisen hammashihnaservokäytön dynaamista käytöstä kuvaava matemaatti­nen malli ja laaditaan mallin pohjalta laitteen simulointimalli. Mallin toimivuus varmistetaan käytän­nön identifiointitesteillä. Lisäksi työssä tut­kitaan, kuinka hyvään suorituskykyyn lineaarinen hammas­hihnaservokäyttö kyke­nee, jos teollisuudessa paikoitussäätörakenteena tyypillisesti käytetty kaskadira­kenne tai PID-rakenne korvataan kehittyneemmällä mallipohjaisella tilasäädinra­kenteella. Säädön toi­mintaa arvioidaan simulointien ja koelaitteistolla suoritetta­vien mittaus­ten perusteella.

Kartonkipakkauskoneen dynaaminen kireydenhallinta

Työssä tutkitaan PI-säätimen käyttöä dynaamisessa kireydensäädössä ilman varsinaista kireyden takaisinkytkentää. Kireyttä säädetään epäsuorasti käyttämällä takaisinkytkentätietona kahden telan välistä paikkaeroa. Kireyssäädin toteutetaan nopeussäätimen rinnalle. Rinnakkaisrakenteella pyritään kireyden muutoksiin nopeasti reagoivaan säätöratkaisuun. Rakenne toteutetaan osaksi taajuusmuuttajan säätöketjua. Työssä esitetään telasysteemin simulointimalli, jonka toimivuus varmistetaan käytännön mittauksin. Lisäksi työssä arvioidaan kireyssäädön toimintaa dynaamisessa kireydensäädössä simulointien ja testilaitteistolla suoritettavien mittausten perusteella.

Moottorin paikkasäädön toteutus dsPIC-ohjaimella

Työssä suunniteltiin nostinsimulaattorin z-akselin suuntaiselle moottorille paikkasäätö ja sen ohjaus CAN-väylää pitkin. Työ toteutettiin projektiryhmässä, jossa eri henkilöt vastasivat eri osa-alueista. CAN-kommunikointi saatiin toimimaan ja lisäksi moottorilta pystyttiin lukemaan paikkatieto talteen. Moottorin säätö jäi vielä puuttumaan.

Position sensorless electrically excited synchronous motor drive for industrial use based on direct flux linkage and torque control

Synchronous machines with an AC converter are used mainly in large drives, for example in ship propulsion drives as well as in rolling mill drives in steel industry. These motors are used because of their high efficiency, high overload capacity and good performance in the field weakening area. Present day drives for electrically excited synchronous motors are equipped with position sensors. Most drives for electrically excited synchronous motors will be equipped with position sensors also in future. This kind of drives with good dynamics are mainly used in metal industry. Drives without a position sensor can be used e.g. in ship propulsion and in large pump and blower drives. Nowadays, these drives are equipped with a position sensor, too. The tendency is to avoid a position sensor if possible, since a sensor reduces the reliability of the drive and increases costs (latter is not very significant for large drives). A new control technique for a synchronous motor drive is a combination of the Direct Flux Linkage Control (DFLC) based on a voltage model and a supervising method (e.g. current model). This combination is called Direct Torque Control method (DTC). In the case of the position sensorless drive, the DTC can be implemented by using other supervising methods that keep the stator flux linkage origin centered. In this thesis, a method for the observation of the drift of the real stator flux linkage in the DTC drive is introduced. It is also shown how this method can be used as a supervising method that keeps the stator flux linkage origin centered in the case of the DTC. In the position sensorless case, a synchronous motor can be started up with the DTC control, when a method for the determination of the initial rotor position presented in this thesis is used. The load characteristics of such a drive are not very good at low rotational speeds. Furthermore, continuous operation at a zero speed and at a low rotational speed is not possible, which is partly due to the problems related to the flux linkage estimate. For operation in a low speed area, a stator current control method based on the DFLC modulator (DMCQ is presented. With the DMCC, it is possible to start up and operate a synchronous motor at a zero speed and at low rotational speeds in general. The DMCC is necessary in situations where high torque (e.g. nominal torque) is required at the starting moment, or if the motor runs several seconds at a zero speed or at a low speed range (up to 2 Hz). The behaviour of the described methods is shown with test results. The test results are presented for the direct flux linkage and torque controlled test drive system with a 14.5 kVA, four pole salient pole synchronous motor with a damper winding and electric excitation. The static accuracy of the drive is verified by measuring the torque in a static load operation, and the dynamics of the drive is proven in load transient tests. The performance of the drive concept presented in this work is sufficient e.g. for ship propulsion and for large pump drives. Furthermore, the developed methods are almost independent of the machine parameters.

Proaktiivinen verkonvalvonta ja reaaliaikainen dokumentaatio

Nykyaikaisen teollisuusympäristön toiminta nojaa pitkälti tietotekniikkaan,erityisesti tietoliikenneverkolla on merkittävä rooli. Jos verkkokatkon vuoksi informaatio ei kulje tehtaan eri yksiköiden välillä, saattaa koko tehdas pysähtyä. Tästä puolestaan voi seurata merkittäviä tuotannollisia menetyksiä. Tietoliikenneverkon häiriöttömän toiminnan varmistamisessa valvonta onkeskeisessä asemassa. Valvontatyökaluilla nähdään muun muassa verkon eri osa-alueiden kuormitus ja saadaan hälytys, jos jokin raja-arvo ylitetään tai jokin komponentti lakkaa toimimasta. Toinen tärkeä seikka on tietoliikenneverkon dokumentaatio, josta nähdään verkon rakenne, komponenttien fyysinen sijainti ja miten neon kytketty toisiinsa. Yhdistämällä valvonnan, dokumentaation ja osaavan henkilökunnan, päästään proaktiiviiseen verkonvalvontaan, jossa vikoja voidaan välttääja ehkäistä ennakkoon tehdyillä toimenpiteillä. Tärkeydestään huolimatta tietoliikenneverkon dokumentaatio on usein jätetty kokonaan tekemättä tai ainakaan se ei ole ajan tasalla. Tähän on monia syitä, joista eräs on kunnollisen dokumentaatio-ohjelmiston puuttuminen. Siksi tässä työssä kehitetään reaaliaikainen dokumentaatiojärjestelmä, jonka avulla tietoliikenneverkon dokumentointi voidaan tehdä, ja jonka ansiosta se myös pysyy ajan tasalla tietojen automaattisen päivityksen ansiosta.

On Modelling, System Identification and Control of Servo-Systems with a Flexible Load

The present study was done with two different servo-systems. In the first system, a servo-hydraulic system was identified and then controlled by a fuzzy gainscheduling controller. The second servo-system, an electro-magnetic linear motor in suppressing the mechanical vibration and position tracking of a reference model are studied by using a neural network and an adaptive backstepping controller respectively. Followings are some descriptions of research methods. Electro Hydraulic Servo Systems (EHSS) are commonly used in industry. These kinds of systems are nonlinearin nature and their dynamic equations have several unknown parameters.System identification is a prerequisite to analysis of a dynamic system. One of the most promising novel evolutionary algorithms is the Differential Evolution (DE) for solving global optimization problems. In the study, the DE algorithm is proposed for handling nonlinear constraint functionswith boundary limits of variables to find the best parameters of a servo-hydraulic system with flexible load. The DE guarantees fast speed convergence and accurate solutions regardless the initial conditions of parameters. The control of hydraulic servo-systems has been the focus ofintense research over the past decades. These kinds of systems are nonlinear in nature and generally difficult to control. Since changing system parameters using the same gains will cause overshoot or even loss of system stability. The highly non-linear behaviour of these devices makes them ideal subjects for applying different types of sophisticated controllers. The study is concerned with a second order model reference to positioning control of a flexible load servo-hydraulic system using fuzzy gainscheduling. In the present research, to compensate the lack of dampingin a hydraulic system, an acceleration feedback was used. To compare the results, a pcontroller with feed-forward acceleration and different gains in extension and retraction is used. The design procedure for the controller and experimental results are discussed. The results suggest that using the fuzzy gain-scheduling controller decrease the error of position reference tracking. The second part of research was done on a PermanentMagnet Linear Synchronous Motor (PMLSM). In this study, a recurrent neural network compensator for suppressing mechanical vibration in PMLSM with a flexible load is studied. The linear motor is controlled by a conventional PI velocity controller, and the vibration of the flexible mechanism is suppressed by using a hybrid recurrent neural network. The differential evolution strategy and Kalman filter method are used to avoid the local minimum problem, and estimate the states of system respectively. The proposed control method is firstly designed by using non-linear simulation model built in Matlab Simulink and then implemented in practical test rig. The proposed method works satisfactorily and suppresses the vibration successfully. In the last part of research, a nonlinear load control method is developed and implemented for a PMLSM with a flexible load. The purpose of the controller is to track a flexible load to the desired position reference as fast as possible and without awkward oscillation. The control method is based on an adaptive backstepping algorithm whose stability is ensured by the Lyapunov stability theorem. The states of the system needed in the controller are estimated by using the Kalman filter. The proposed controller is implemented and tested in a linear motor test drive and responses are presented.

Database Rights in Safe European Home: The Path to More Rigorous Protection of Information

1. Introduction "The one that has compiled ... a database, the collection, securing the validity or presentation of which has required an essential investment, has the sole right to control the content over the whole work or over either a qualitatively or quantitatively substantial part of the work both by means of reproduction and by making them available to the public", Finnish Copyright Act, section 49.1 These are the laconic words that implemented the much-awaited and hotly debated European Community Directive on the legal protection of databases,2 the EDD, into Finnish Copyright legislation in 1998. Now in the year 2005, after more than half a decade of the domestic implementation it is yet uncertain as to the proper meaning and construction of the convoluted qualitative criteria the current legislation employs as a prerequisite for the database protection both in Finland and within the European Union. Further, this opaque Pan-European instrument has the potential of bringing about a number of far-reaching economic and cultural ramifications, which have remained largely uncharted or unobserved. Thus the task of understanding this particular and currently peculiarly European new intellectual property regime is twofold: first, to understand the mechanics and functioning of the EDD and second, to realise the potential and risks inherent in the new legislation in economic, cultural and societal dimensions. 2. Subject-matter of the study: basic issues The first part of the task mentioned above is straightforward: questions such as what is meant by the key concepts triggering the functioning of the EDD such as presentation of independent information, what constitutes an essential investment in acquiring data and when the reproduction of a given database reaches either qualitatively or quantitatively the threshold of substantiality before the right-holder of a database can avail himself of the remedies provided by the statutory framework remain unclear and call for a careful analysis. As for second task, it is already obvious that the practical importance of the legal protection providedby the database right is in the rapid increase. The accelerating transformationof information into digital form is an existing fact, not merely a reflection of a shape of things to come in the future. To take a simple example, the digitisation of a map, traditionally in paper format and protected by copyright, can provide the consumer a markedly easier and faster access to the wanted material and the price can be, depending on the current state of the marketplace, cheaper than that of the traditional form or even free by means of public lending libraries providing access to the information online. This also renders it possible for authors and publishers to make available and sell their products to markedly larger, international markets while the production and distribution costs can be kept at minimum due to the new electronic production, marketing and distributionmechanisms to mention a few. The troublesome side is for authors and publishers the vastly enhanced potential for illegal copying by electronic means, producing numerous virtually identical copies at speed. The fear of illegal copying canlead to stark technical protection that in turn can dampen down the demand for information goods and services and furthermore, efficiently hamper the right of access to the materials available lawfully in electronic form and thus weaken the possibility of access to information, education and the cultural heritage of anation or nations, a condition precedent for a functioning democracy. 3. Particular issues in Digital Economy and Information Networks All what is said above applies a fortiori to the databases. As a result of the ubiquity of the Internet and the pending breakthrough of Mobile Internet, peer-to-peer Networks, Localand Wide Local Area Networks, a rapidly increasing amount of information not protected by traditional copyright, such as various lists, catalogues and tables,3previously protected partially by the old section 49 of the Finnish Copyright act are available free or for consideration in the Internet, and by the same token importantly, numerous databases are collected in order to enable the marketing, tendering and selling products and services in above mentioned networks. Databases and the information embedded therein constitutes a pivotal element in virtually any commercial operation including product and service development, scientific research and education. A poignant but not instantaneously an obvious example of this is a database consisting of physical coordinates of a certain selected group of customers for marketing purposes through cellular phones, laptops and several handheld or vehicle-based devices connected online. These practical needs call for answer to a plethora of questions already outlined above: Has thecollection and securing the validity of this information required an essential input? What qualifies as a quantitatively or qualitatively significant investment? According to the Directive, the database comprises works, information and other independent materials, which are arranged in systematic or methodical way andare individually accessible by electronic or other means. Under what circumstances then, are the materials regarded as arranged in systematic or methodical way? Only when the protected elements of a database are established, the question concerning the scope of protection becomes acute. In digital context, the traditional notions of reproduction and making available to the public of digital materials seem to fit ill or lead into interpretations that are at variance with analogous domain as regards the lawful and illegal uses of information. This may well interfere with or rework the way in which the commercial and other operators have to establish themselves and function in the existing value networks of information products and services. 4. International sphere After the expiry of the implementation period for the European Community Directive on legal protection of databases, the goals of the Directive must have been consolidated into the domestic legislations of the current twenty-five Member States within the European Union. On one hand, these fundamental questions readily imply that the problemsrelated to correct construction of the Directive underlying the domestic legislation transpire the national boundaries. On the other hand, the disputes arisingon account of the implementation and interpretation of the Directive on the European level attract significance domestically. Consequently, the guidelines on correct interpretation of the Directive importing the practical, business-oriented solutions may well have application on European level. This underlines the exigency for a thorough analysis on the implications of the meaning and potential scope of Database protection in Finland and the European Union. This position hasto be contrasted with the larger, international sphere, which in early 2005 does differ markedly from European Union stance, directly having a negative effect on international trade particularly in digital content. A particular case in point is the USA, a database producer primus inter pares, not at least yet having aSui Generis database regime or its kin, while both the political and academic discourse on the matter abounds. 5. The objectives of the study The above mentioned background with its several open issues calls for the detailed study of thefollowing questions: -What is a database-at-law and when is a database protected by intellectual property rights, particularly by the European database regime?What is the international situation? -How is a database protected and what is its relation with other intellectual property regimes, particularly in the Digital context? -The opportunities and threats provided by current protection to creators, users and the society as a whole, including the commercial and cultural implications? -The difficult question on relation of the Database protection and protection of factual information as such. 6. Dsiposition The Study, in purporting to analyse and cast light on the questions above, is divided into three mainparts. The first part has the purpose of introducing the political and rationalbackground and subsequent legislative evolution path of the European database protection, reflected against the international backdrop on the issue. An introduction to databases, originally a vehicle of modern computing and information andcommunication technology, is also incorporated. The second part sets out the chosen and existing two-tier model of the database protection, reviewing both itscopyright and Sui Generis right facets in detail together with the emergent application of the machinery in real-life societal and particularly commercial context. Furthermore, a general outline of copyright, relevant in context of copyright databases is provided. For purposes of further comparison, a chapter on the precursor of Sui Generi, database right, the Nordic catalogue rule also ensues. The third and final part analyses the positive and negative impact of the database protection system and attempts to scrutinize the implications further in the future with some caveats and tentative recommendations, in particular as regards the convoluted issue concerning the IPR protection of information per se, a new tenet in the domain of copyright and related rights.

Integrated Project Portfolio Management as a Tool for Strategic Steering and Business Control

Tutkielman päätavoitteena oli tutkia miten projektisalkun hallinnalla voidaan tukea organisaation strategista ohjausta ja liiketoimintaa. Tämän lisäksi avaintavoitteina oli kuvata projektisalkun hallinnan nykytilanne kohdeyrityksessä, paljastaa erityisiä kehitystarpeita ja lopulta luoda kohdeyrityksen projektisalkunhallinnalle tavoitetila. Kirjallisuuskatsauksessa pohdittiin projektisalkun hallinnan roolia ja tavoitteita, projektisalkun hallinnassa käyttävää prosessia, sekä menetelmiä ja tekniikoita, joilla salkkua hallitaan. Työn empiirisessä osassa syvennyttiin tutkimaan projektinsalkun hallintaan liittyviä erityispiirteitä kohdeyrityksessä. Tutkimustulosten huolellinen analysointi osoitti, että aikaisempi kirjallisuus ei riittävästi huomioi kokonaisvaltaisen, integroidun lähestymistavan tarvetta ja viestinnän tärkeyttä projektisalkun hallinnassa. Tutkimuksen johtopäätöksinä luotiin uusi integroitu projektisalkun hallintamalli ja määriteltiin kohdeyritykselle projektisalkun hallinnan tavoitetila sekä ne kehitysaskeleet, joita yrityksen tulisi lähitulevaisuudessa ottaa.

Market Study of Electric Drive Motion Control Business

Tämän diplomityön tavoitteena oli tutkia älykkäiden paikoituskäyttöjen markkinoita ja liiketoimintamalleja. Työn pääongelmina oli määritellä alalla käytössä olevaa terminologiaa, määrittää markkinoiden koko paikoitusominaisuudet omaaville kolmivaihetaajuusmuuttajille, tutkia viiden alalla toimivan paikoituskäyttötoimittajan liiketoimintarakenteita ja tuotteita teknisestä näkökulmasta sekä esitellä kaksi teollisuuden käyttökohdetta paikoituskäytölle. Työn sisältö voidaan jakaa neljään eri osioon. Terminologian määrittely- ja markkinatutkimusosiot perustuvat pääasiassa kirjallisuustutkimukseen. Paikoituskäyttöjen toimittajia sekä niiden tuotteita käsittelevä osuus perustuu kirjallisuustutkimukseen sekä teknisiin esitteisiin ja manuaaleihin. Paikoituskäyttöjen sovellusesimerkit on selvitetty haastatteluin. Työ painottuu paikoituskäyttötoimittajien tuotteiden, tuoteominaisuuksien ja tuotetarjonnan tarkasteluun. Työn tuloksena on määritelty paikoituskäyttöjen liiketoiminnan tärkeimmät termit, paikoituskäyttöjen markkinoiden koko sekä markkinoiden koko paikoitusominaisuudet omaavalle kolmivaihetaajuusmuuttajalle. Alalla toimivien paikoituskäyttötoimittajien liiketoimintarakenne on selvitetty, jonka mukaan toimittajat on profiloitu komponentti-, komponenttipaketti-, toimialakeskeisiksi tai automaatiotoimittajiksi. Toimittajien paikoituskäyttötuotteet on luokiteltu viiteen eri luokkaan niiden teknisten ominaisuuksien perusteella. Lisäksi paikoituskäyttöjen suorituskyvyt on selvitetty säätimien momentti-, nopeus-, ja paikoituslaskenta-aikatasojen sekä kenttäväyläliityntöjen suhteen. Työssä kuvatut vanerinsorvausprosessi sekä FMS -materiaalinkäsittelyprosessi esittävät paikoituskäyttöjen potentiaalisia sovelluskohteita.

The effects of real time control of welding parameters on weld quality in plasma arc keyhole welding

Joints intended for welding frequently show variations in geometry and position, for which it is unfortunately not possible to apply a single set of operating parameters to ensure constant quality. The cause of this difficulty lies in a number of factors, including inaccurate joint preparation and joint fit up, tack welds, as well as thermal distortion of the workpiece. In plasma arc keyhole welding of butt joints, deviations in the gap width may cause weld defects such as an incomplete weld bead, excessive penetration and burn through. Manual adjustment of welding parameters to compensate for variations in the gap width is very difficult, and unsatisfactory weld quality is often obtained. In this study a control system for plasma arc keyhole welding has been developed and used to study the effects of the real time control of welding parameters on gap tolerance during welding of austenitic stainless steel AISI 304L. The welding tests demonstrated the beneficial effect of real time control on weld quality. Compared with welding using constant parameters, the maximum tolerable gap width with an acceptable weld quality was 47% higher when using the real time controlled parameters for a plate thickness of 5 mm. In addition, burn through occurred with significantly larger gap widths when parameters were controlled in real time. Increased gap tolerance enables joints to be prepared and fit up less accurately, saving time and preparation costs for welding. In addition to the control system, a novel technique for back face monitoring is described in this study. The test results showed that the technique could be successfully applied for penetration monitoring when welding non magnetic materials. The results also imply that it is possible to measure the dimensions of the plasma efflux or weld root, and use this information in a feedback control system and, thus, maintain the required weld quality.