50 resultados para swd: Multi-Touch-Screen

em Doria (National Library of Finland DSpace Services) - National Library of Finland, Finland


Relevância:

20.00% 20.00%

Publicador:

Resumo:

This final project was made for the Broadband/Implementation department of TeliaSonera Finland. The question to be examined is if the operator should replace multiple ADSL connections implemented over a leased line with Multi-Dwelling access based on an Ethernet/Optical Fibre access network. The project starts with describing the technology related to these access network solu-tions and presents the technology that is used in TeliaSonera Finland's access network. It continues from the technology to describe the problem with some of the ADSL implemen-tations of TeliaSonera. The problem is the implementations done over a leased line that can cost TeliaSonera over years as much as a possible investment to extend network when there is several lines leased to the same building. The project proposes a Multi-Dwelling access as a solution to this problem and defines the circumstances when to use it. After a satisfactory solution has found the project takes a view how implementation of the solution might alter the network and a new problem is found. When used commonly to replace need of ADSL implementation Multi-Dwelling access would significantly increase optical cable congestion near operators POP. As a final deed this project also proposes a technical change to existing way to implement multi-dwelling access with EPON technology.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Diplomityö muodostuu kahdesta kokonaisuudesta. Työn teoriaosa kertoo mitä ympäristöjohtaminen on, millaisia ovat multi-site -organisaatio ja multi-site -johtamisjärjestelmä sekä mitä vaatimuksia nämä asettavat yritykselle. Työssä esitetään malli, jota käyttämällä kansainvälisten johtamisjärjestelmästandardien mukaan rakennetut laatu-, ympäristö-, terveys- ja turvallisuusjärjestelmät voidaan yhdistää yhdeksi kokonaisuudeksi, multi-site - johtamisjärjestelmäksi. Malli rakentuu kolmesta tasosta, joita ovat paikallinen, maakohtainen ja konsernitaso. Esimerkkien avulla kerrotaan miteneri lähtökohdista voidaan näiden tasojen kautta edetä kohti yhtä johtamiskokonaisuutta. Esille tuodaan myös multi-site -johtamisjärjestelmän käyttöönottoa puoltavat ja vastustavat näkökohdat. Työn konkreettinen osa on johtamisjärjestelmämallin paikallisen tason toteuttaminen. Ympäristöjohtamisjärjestelmän rakentaminen standardin EN ISO 14001:2004 vaatimusten mukaiseksi Kvaerner Power Oy:n Suomen toimipaikoille sekä tämän järjestelmän yhdistäminen sertifioituun EN ISO 9001 -standardin mukaiseen laatujärjestelmään. Työssä kerrotaan miten ympäristöjohtamisjärjestelmä on rakennettu ja miten laatu- ja ympäristöjärjestelmät on liitetty yhdeksi kokonaisuudeksi. Työn tuloksena syntyi malli johtamisjärjestelmien yhdistämisestä sekä sertifioitu ympäristöjohtamisjärjestelmä, jonka yhdistäminen laatujärjestelmään toteutettiin tavoitteiden mukaisesti.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

An alternative relation to Pareto-dominance relation is proposed. The new relation is based on ranking a set of solutions according to each separate objective and an aggregation function to calculate a scalar fitness value for each solution. The relation is called as ranking-dominance and it tries to tackle the curse of dimensionality commonly observedin evolutionary multi-objective optimization. Ranking-dominance can beused to sort a set of solutions even for a large number of objectives when Pareto-dominance relation cannot distinguish solutions from one another anymore. This permits search to advance even with a large number of objectives. It is also shown that ranking-dominance does not violate Pareto-dominance. Results indicate that selection based on ranking-dominance is able to advance search towards the Pareto-front in some cases, where selection based on Pareto-dominance stagnates. However, in some cases it is also possible that search does not proceed into direction of Pareto-front because the ranking-dominance relation permits deterioration of individual objectives. Results also show that when the number of objectives increases, selection based on just Pareto-dominance without diversity maintenance is able to advance search better than with diversity maintenance. Therefore, diversity maintenance is connive at the curse of dimensionality.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

The purpose of this dissertation is to increase the understanding and knowledge of field sales management control systems (i.e. sales managers monitoring, directing, evaluating and rewarding activities) and their potential consequences on salespeople. This topic is important because research conducted in the past has indicated that the choice of control system type can on the other hand have desirable consequences, such as high levels of motivation and performance, and on the other hand leadto harmful unintended consequences, such as opportunistic or unethical behaviors. Despite the fact that marketing and sales management control systems have been under rigorous research for over two decades, it still is at a very early stage of development, and several inconsistencies can be found in the research results. This dissertation argues that these inconsistencies are mainly derived from misspecification of the level of analysis in the past research. These different levels of analysis (i.e. strategic, tactical, and operational levels) involve very different decision-making situations regarding the control and motivation of sales force, which should be taken into consideration when conceptualizing the control. Moreover, the study of salesperson consequences of a field sales management control system is actually a cross-level phenomenon, which means that at least two levels of analysis are simultaneously involved. The results of this dissertation confirm the need to re-conceptualize the field sales management control system concept. It provides empirical evidence for the assertion that control should be conceptualized with more details atthe tactical/operational level of analysis than at the strategic levelof analysis. Moreover, the results show that some controls are more efficiently communicated to field salespeople than others. It is proposed that this difference is due to different purposes of control; some controls aredesigned for influencing salespersons' behavior (aim at motivating) whereas some controls are designed to aid decision-making (aim at providing information). According to the empirical results of this dissertation, the both types of controls have an impact to the sales force, but this impactis not as strong as expected. The results obtained in this dissertation shed some light to the nature of field sales management control systems, and their consequences on salespeopl

Relevância:

20.00% 20.00%

Publicador:

Resumo:

In this study, equations for the calculation of erosion wear caused by ash particles on convective heat exchanger tubes of steam boilers are presented. Anew, three-dimensional test arrangement was used in the testing of the erosion wear of convective heat exchanger tubes of steam boilers. When using the sleeve-method, three different tube materials and three tube constructions could be tested. New results were obtained from the analyses. The main mechanisms of erosionwear phenomena and erosion wear as a function of collision conditions and material properties have been studied. Properties of fossil fuels have also been presented. When burning solid fuels, such as pulverized coal and peat in steam boilers, most of the ash is entrained by the flue gas in the furnace. In bubbling andcirculating fluidized bed boilers, particle concentration in the flue gas is high because of bed material entrained in the flue gas. Hard particles, such as sharp edged quartz crystals, cause erosion wear when colliding on convective heat exchanger tubes and on the rear wall of the steam boiler. The most important ways to reduce erosion wear in steam boilers is to keep the velocity of the flue gas moderate and prevent channelling of the ash flow in a certain part of the cross section of the flue gas channel, especially near the back wall. One can do this by constructing the boiler with the following components. Screen plates can beused to make the velocity and ash flow distributions more even at the cross-section of the channel. Shield plates and plate type constructions in superheaters can also be used. Erosion testing was conducted with three types of tube constructions: a one tube row, an inline tube bank with six tube rows, and a staggered tube bank with six tube rows. Three flow velocities and two particle concentrations were used in the tests, which were carried out at room temperature. Three particle materials were used: quartz, coal ash and peat ash particles. Mass loss, diameter loss and wall thickness loss measurements of the test sleeves were taken. Erosion wear as a function of flow conditions, tube material and tube construction was analyzed by single-variable linear regression analysis. In developing the erosion wear calculation equations, multi-variable linear regression analysis was used. In the staggered tube bank, erosion wear had a maximum value in a tube row 2 and a local maximum in row 5. In rows 3, 4 and 6, the erosion rate was low. On the other hand, in the in-line tube bank the minimum erosion rate occurred in tube row 2 and in further rows the erosion had an increasing value, so that in a six row tube bank, the maximum value occurred in row 6.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Työn tavoitteena oli kehittää prosessia fraktioinnista monikerrosperälaatikolle painopaperilajeilla. Tarkoituksena oli selvittää koeajojen avulla sihti- ja pyörrepuhdistusfraktioinnin soveltuvuutta paperin kerrostuksen kannalta. Työssä vertailtiin keskenään fraktiointimenetelmiä ja niiden yhdistelmiä. Tehtävänä oli prosessikonseptin kehittäminen eri prosessikytkennöistä ja –ratkaisuista simuloinnin avulla. Kirjallisuusosassa tutustuttiin analysoiden kirjallisuusviitteiden perusteella massan fraktiointiin ja paperin kerrostamiseen sekä fraktiointikerrostetun rainan karakterisointiin. Tavoitteiden saavuttamiseksi esikokeena suoritettiin pilotkoeajo hienopaperimassalla, jossa tutkittiin pääasiassa fraktiointitulosta. Toinen koeajo suoritettiin LWC-paperilla, jossa koekonekonsepti oli optimaalisempi kerrostuksen kannalta ja fraktiointitulos voitiin linkittää paperin laatusuureisiin. LWC-koeajossa fraktioidulla massalla tehtiin laboratoriomittakaavassa monikerrosarkkimuottikokeita, joiden tuloksilla pyrittiin vahvistamaan koeajosta saatuja tuloksia ja fraktioinnnin potentialia. Prosessikonseptin kehittämiseksi rakennettiin seitsemän simulointimallia eri kytkennöistä. Malleja verrattiin keskenään täyteaine- ja kuitujakeiden fraktiointikyvyn perusteella. Koeajojen avulla selvitettiin fraktioinnin kannalta optimaaliset prosessimuuttujat. Fraktiointikerrostuksella parannettiin paperin z-suuntaista lujuutta ja etenkin pyörrepuhdistinfraktioinnilla pintojen sileyttä. Fraktiointikerrostuksella voitiin parantaa paperin täyteainejakaumaa. Kokeiden perusteella huomattiin, että kukin paperilaji tarvitsee erilaisen fraktiointijärjestelyn riippuen käytetystä massasta ja täyteaineesta.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Tässä diplomityössä haluttiin mallintaa kuidutusrummun toimintaa Fluent virtausmallinusohjelman avulla. Aikaisempi tieto ja kehitystyö on perustunut kokemukseen ja käytännön kokeisiin. Kehitystyön alkuaikoina on suoritettu muutamia laskelmia koskien rummun tuottoa mutta sen jälkeen ei toimintaa ole laskennallisesti kuvattu. Työn ensimmäinen osa käsittelee yleisesti keräyspaperin käsittelyyn liittyviä laitteita ja menetelmiä. Toimintaperiaatteita on kuvattu yleisellä tasolla ja FibreFlow® rumpu on sitten käsitelty muita laitteita tarkemmin. Työn toinen osa sisältää sitten laboratoriotestit paikallisilta tahteilta hankittujen näytteiden viskositeettien ja tiheyksien määrittämiseksi. Kokeet suoritettiin Kemiantekniikan osastolla Brookfield viskoosimetrillä. Joitain alustavia laskentoja tuotosta suoritettiin aikaisempien tietojen perusteella. Rumpua kun on valmistettu vuodesta 1976, on tietoa kertynyt runsaasti vuosien mittaan. Laskelmia varten valittiin mallinnettavaksi alueeksi vain yksittäinen reikä sihdistä jolle laskettiin massavirta. Käytetyt laadut olivat OCC ja DIP. Myös eri rumpukoot otettiin jossain määrin huomioon.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Diplomityö tarkastelee säikeistettyä ohjelmointia rinnakkaisohjelmoinnin ylemmällä hierarkiatasolla tarkastellen erityisesti hypersäikeistysteknologiaa. Työssä tarkastellaan hypersäikeistyksen hyviä ja huonoja puolia sekä sen vaikutuksia rinnakkaisalgoritmeihin. Työn tavoitteena oli ymmärtää Intel Pentium 4 prosessorin hypersäikeistyksen toteutus ja mahdollistaa sen hyödyntäminen, missä se tuo suorituskyvyllistä etua. Työssä kerättiin ja analysoitiin suorituskykytietoa ajamalla suuri joukko suorituskykytestejä eri olosuhteissa (muistin käsittely, kääntäjän asetukset, ympäristömuuttujat...). Työssä tarkasteltiin kahdentyyppisiä algoritmeja: matriisioperaatioita ja lajittelua. Näissä sovelluksissa on säännöllinen muistinkäyttökuvio, mikä on kaksiteräinen miekka. Se on etu aritmeettis-loogisissa prosessoinnissa, mutta toisaalta huonontaa muistin suorituskykyä. Syynä siihen on nykyaikaisten prosessorien erittäin hyvä raaka suorituskyky säännöllistä dataa käsiteltäessä, mutta muistiarkkitehtuuria rajoittaa välimuistien koko ja useat puskurit. Kun ongelman koko ylittää tietyn rajan, todellinen suorituskyky voi pudota murto-osaan huippusuorituskyvystä.