Superconducting properties and their enhancement in ReBa2Cu3O7-delta (RE = Y and Gd) films prepared by pulsed laser deposition

Due to font problem on the tilte field the titlte of the thesis is corrected here. The title of the thesis is: Superconducting properties and their enhancement in ReBa₂Cu₃O₇-delta (RE = Y and Gd) films prepared by pulsed laser deposition

Microcracks and Vortices in Superconducting Thin Films

In this work, superconducting YBa₂ Cu₃O_6+x (YBCO) thin films have been studied with the experimental focus on the anisotropy of BaZrO₃ (BZO) doped YBCOthin films and the theoretical focus on modelling flux pinning by numerically solving Ginzburg- Landau equations. Also, the structural properties of undoped YBCO thin films grown on NdGaO₃ (NGO) and MgO substrates were investigated. The thin film samples were made by pulsed laser ablation on single crystal substrates. The structural properties of the thin films were characterized by X-ray diffraction and atomic force microscope measurements. The superconducting properties were investigated with a magnetometer and also with transport measurements in pulsed magnetic field up to 30 T. Flux pinning was modelled by restricting the value of the order parameter inside the columnar pinning sites and then solving the Ginzburg-Landau equations numerically with the restrictions in place. The computations were done with a parallel code on a supercomputer. The YBCO thin films were seen to develop microcracks when grown on NGO or MgO substrates. The microcrack formation was connected to the structure of the YBCO thin films in both cases. Additionally, the microcracks can be avoided by careful optimization of the deposition parameters and the film thickness. The BZO doping of the YBCO thin films was seen to decrease the effective electron mass anisotropy, which was seen by fitting the Blatter scaling to the angle dependence of the upper critical field. The Ginzburg-Landau simulations were able to reproduce the measured magnetic field dependence of the critical current density for BZO doped and undoped YBCO. The simulations showed that in addition to the large density also the large size of the BZO nanorods is a key factor behind the change in the power law behaviour between BZO doped and undoped YBCO. Additionally, the Ginzburg-Landau equations were solved for type I thin films where giant vortices were seen to appear depending on the film thickness. The simulations predicted that singly quantized vortices are stable in type I films up to quite large thicknesses and that the size of the vortices increases with decreasing film thickness, in a way that is similar to the behaviour of the interaction length of Pearl vortices.

Hyperfine interactions in the new Fe-based superconducting structures and related magnetic phases

This thesis is devoted to the study of the hyperfine properties in iron-based superconductors and the synthesis of these compounds and related phases. During this work polycrystalline chalcogenide samples with stoichiometry 1:1 (FeTe1-χSχ, FeSe1-x) and pnictide samples with stoichiometry 1:2:2 (BaFe2(As1-χPχ)2, EuFe2(As1-x Px)2) were synthesized by solid-state reaction methods in vacuum and in a protecting Ar atmosphere. In several cases post-annealing in oxygen atmosphere was employed. The purity and superconducting properties of the obtained samples were checked with X-ray diffraction, SQUID and resistivity measurements. For studies of the magnetic properties of the investigated samples Mössbauer spectroscopy was used. Using low-temperature measurements around Tc and various values of the source velocity the hyperfine interactions were obtained and the magnetic and structural properties in the normal and superconducting states could be studied. Mössbauer measurements together with XRD characterization were also used for the detection of impurity phases. DFT calculations were used for the theoretical study of Mössbauer parameters for pnictide-based ᴻsamples BaFe2(As1-xPx)2 and EuFe2(As1-xPx)2.

Finite size effects in superconducting nanocomposites

The present Master’s thesis presents theoretical description of the extraodinary behavior of the confined Indium nanoparticles. Superconducting properties of nanoparticles and nanocomposites are extensively reviewed. Special attention has been paid to phase fluctuation, shell and disordered effects. The experimental data has been obtained and provided by Dmitry Shamshur from Ioffe Physical Technical Institute. The investigated material represents a highly ordered system of silicate spheres filled with indium metal, where the In nanoparticles are interconnected between each other. Bulk indium is a superconductor with crititcal superconducting temperature Tc0 = 3:41 K. But indium nanoparticles exhibit different behavior, the critical temperature rise by approximately 20% up to 4.15 K. As well as transition of the indium particles to type-II superconductivity with high critical magnetic fields. Such diversity is explained by finite size effects which originate from nanosize of the samples.

Hitsausparametrien vaikutus rakenneteräksen MAG-hitsin laatuun

Työn tavoitteena oli löytää teräksen S355 MAG alapienahitsaukselle, 6mm:n levypaksuudelle sellaiset parametri-ikkunat, joissa hitsin ja perusaineen liittyminen on mahdollisimman jouheva. Hitsin laadunja hitsausparametrien välille pyritiin löytämään matemaattista korrelaatiota. Työ painottui hitsin muotoon sekä hitsin ja perusaineen liittymiseen. Työstä saatuja tuloksia käytettiin hitsattaessa väsytyskoekappaleita mutta niiden tutkiminen ei sisältynyt tähän työhön. Työssä haettiin parametreja a-mitaltaan 4mm:n alapienahitsille kahdeksalle yleisesti käytetylle hitsauslangalle, joista kolme oli umpilankaa, neljä metallitäytelankaa ja yksi rutiilitäytelanka ja kaasuina käytettiin kahta argon hiilidioksidi seoskaasua ja kahta argon helium seoskaasua.

Viirojen vedenpoistokyvyn ja markkeeraavuuden analysointi HSRT-laitteistolla

Tässä diplomityössä tutkittiin eri tyyppisten viirojen vedenpoisto-ominaisuuksia ja markkeeraavuutta HSRT-laitteistolla. Tarkoitus oli myös selvittää muodostuvan paperiarkin rakennetta ja HSRT-laitteiston soveltuvuutta viiravertailuun. Työn kirjallisuusosassa käsitellään märkäviiroja sekä niiden valmistamista, valintaa eri kriteerein, kulumista ja puhdistamista. Lisäksi käsitellään viirojen markkeeraavuutta ja viiraosan vedenpoistoa. Sekä vedenpoistokyvyn että markkeeraavuuden osalta tulokset olivat niin tasaiset eri suureiden suhteen, ettei etenkään sisäviirojen välillä saatu näkyviin selviä eroja. Markkeeraavuuden osalta laitteiston ominaisuutena näyttäisi olevan se, ettei sisäviiran puoleinen markkeeraus näy arkissa. Tästä syystä vertailut DPCJ-laitteen ja koepaperikoneen tuloksiin olivat mahdottomia. Sen sijaan ulkoviiran puolella markkeeraus oli havaittavissa useimmissa tapauksissa. Tutkimuksen perusteella vaikuttaa kuitenkin siltä, ettei HSR-Tester sovellu viirojen vedenpoistonkyvyn ja markkeeraavuuden vertailuun.

Erikoispaperin käyristymisen pienentäminen mittapysyvyyttä parantamalla

Diplomityössä on tutkittu Tervakoski Oy:n PK8:lla valmistettavan irrokepaperin mittapy-syvyysongelmaa. Tämä ilmenee asiakkaan jatkojalostusprosesseissa esim. silikonointi- ja liimausvaiheissa paperin huonona ajettavuutena. Työ pohjautuu PK8:lla suoritettavien tehdasmittakaavaisten koeajojen prosessiolosuhteiden ja mittapysyvyyttä kuvaavien analyysien tulosten tarkasteluun. Työn kirjallisuusosassa kerrotaan silikonointi- ja laminointiprosessin vaatimuksista irrokepaperille. Mittapysyvyyden teoreettista taustaa lähestytään puukuidun sorptio-ominaisuuksien tarkastelulla. Osassa perehdytään mm. paperin mittapysyvyyteen ja käyristymiseen vaikuttaviin eri tekijöihin. Osio sisältää myös katsauksen paperin mittapysyvyyden ja käyristymisen eri mittausmenetelmistä. Työn kokeellisessa osassa tarkastellaan PK8:n prosessiolosuhteiden vaikutuksia mittapysy- vyyden tasoon. Kokeellinen osa sisältää neljä tehdasmittakaavaista koeajosarjaa ja 23 eri koepistettä, joiden tarkoituksena on löytää PK8:lle mittapysyvyyden kannalta parhaimmat mahdolliset olosuhteet muiden laatuarvojen kärsimättä. Koesarjojen muuttujina on käytetty kuivatusviirojen kireyttä, konesuuntaista vetojännitystä sekä suihkusuhteen ja jauhatusasteen muutoksia. Lisäksi paperin käyristymiseen pyrittiin vaikuttamaan PK8:lla toispuoleisella kuivatuksella ja erilliskostutuskoneen toispuoleisella kostutusvesimäärällä. Koesarjojen prosessiolosuhteiden ja analyysitulosten perusteella PK8:lla muutettiin ajotapamallia jo työn kuluessa. Kokeellisen osan loputtua PK8:n tuotantolinjalle määriteltiin uusi ajotapamalli. PK8:n tuotantolinjalla valmistettavan glassiinin poikkisuuntainen kuivatuskutistuma aleni eräässä koesarjassa prosessiolosuhteiden muutosten myötä noin 13 %. Mittapysy-vyyttä kuvaavat kosteuslaajentuma, märkämuodonmuutos ja käyristyminen paranivat keskimäärin 11 %. Uuden ajotapamallin myötä PK8:n valmistaman irrokepaperin laatutaso on noussut, jolloin on jo nyt havaittu, että glassiinin ajettavuus on selkeästi parantunut asiakkaan jatkojalostusprosesseissa.

Tandem-GMA Welding of Low Alloy Structural Steel

The Tandem-GMAW method is the latest development as the consequences of improvements in the welding methods. The twin-wire and then the Tandem-method with the separate power sources has got a remarkable place in the welding of many types of materials with different joint types. The biggest advantage of Tandem welding method is the flexibility of choosing both the electrodes of different types from each other according to the type of the parent material. This is possible because of the feasibility of setting the separate welding parameters for both the wires. In this thesis work the effect of the variation in three parameters on the weld bead in Tandem-GMA welding method is studied. Theses three parameters are the wire feed rate in the slave wire, the wire feed rate in the master wire and the voltage difference in both the wires. The results are then compared to study the behaviour of the weld bead with the change in these parameters.

Studies of Eu- and Yb-induced Reconstructions on the Si(100) Surface

This thesis presents experimental studies of rare earth (RE) metal induced structures on Si(100) surfaces. Two divalent RE metal adsorbates, Eu and Yb, are investigated on nominally flat Si(100) and on vicinal, stepped Si(100) substrates. Several experimental methods have been applied, including scanning tunneling microscopy/spectroscopy (STM/STS), low energy electron diffraction (LEED), synchrotron radiation photoelectron spectroscopy (SR-PES), Auger electron spectroscopy (AES), thermal desorption spectroscopy (TDS), and work function change measurements (Δφ). Two stages can be distinguished in the initial growth of the RE/Si interface: the formation of a two-dimensional (2D) adsorbed layer at submonolayer coverage and the growth of a three-dimensional (3D) silicide phase at higher coverage. The 2D phase is studied for both adsorbates in order to discover whether they produce common reconstructions or reconstructions common to the other RE metals. For studies of the 3D phase Yb is chosen due to its ability to crystallize in a hexagonal AlB2 type lattice, which is the structure of RE silicide nanowires, therefore allowing for the possibility of the growth of one-dimensional (1D) wires. It is found that despite their similar electronic configuration, Eu and Yb do not form similar 2D reconstructions on Si(100). Instead, a wealth of 2D structures is observed and atomic models are proposed for the 2×3-type reconstructions. In addition, adsorbate induced modifications on surface morphology and orientational symmetry are observed. The formation of the Yb silicide phase follows the Stranski-Krastanov growth mode. Nanowires with the hexagonal lattice are observed on the flat Si(100) substrate, and moreover, an unexpectedly large variety of growth directions are revealed. On the vicinal substrate the growth of the silicide phase as 3D islands and wires depends drastically on the growth conditions. The conditions under which wires with high aspect ratio and single orientation parallel to the step edges can be formed are demonstrated.

Runkopalkkien valmistuksen kehittäminen

Diplomityössä kehitetään runkopalkkien valmistusta Juhani Haavisto Oy:ssä. Palkkien valmistusta käsitellään hitsauksen ja koneistuksen osalta. Työn alussa perehdytään hitsauksen mekanisointiin, hitsattavuuteen, lastuttavuuteen sekä hitsaus- ja koneistuskiinnittimiin teorian osalta. Tämän jälkeen esitellään valmistettava tuote. Kokeellisessa osassa esitetään runkopalkkien valmistusvaiheet ennen ja jälkeen kehityksen. Esille tulevat niin hitsauksen kuin koneistuksenkin valmistusvaiheet. Tutkimuksessa selvisi, että uudet hitsaus- ja koneistuskiinnittimet pienentävät työaikoja mm. mahdollistamalla laajemman mekanisoidun hitsauksen ja pienentämällä kappaleen kääntöihin ja vaihtoon kuluvaa aikaa. Lopuksi pohditaan mahdollisia jatkokehityssuunnitelmia, jotka koskevat uuden hitsauskuljettimen ja uusien lisäaineiden käyttöä.

Hybrid LC Filter for Power Electronic Drives: Theory and Implementation

Power electronic converter drives use, for the sake of high efficiency, pulse-width modulation that results in sequences of high-voltage high-frequency steep-edged pulses. Such a signal contains a set of high harmonics not required for control purposes. Harmonics cause reflections in the cable between the motor and the inverter leading to faster winding insulation ageing. Bearing failures and problems with electromagnetic compatibility may also result. Electrical du/dt filters provide an effective solution to problems caused by pulse-width modulation, thereby increasing the performance and service life of the electrical machines. It is shown that RLC filters effectively decrease the reflection phenomena in the cable. Improved (simple, but effective) solutions are found for both differential- and common-mode signals; these solutions use a galvanic connection between the RLC filter star point and the converter DC link. Foil chokes and film capacitors are among the most widely used components in high-power applications. In actual applications they can be placed in different parts of the cabinet. This fact complicates the arrangement of the cabinet and decreases the reliability of the system. In addition, the inductances of connection wires may prevent filtration at high frequencies. This thesis introduces a new hybrid LC filter that uses a natural capacitance between the turns of the foil choke based on integration of an auxiliary layer into it. The main idea of the hybrid LC filter results from the fact that both the foil choke and the film capacitors have the same roll structure. Moreover, the capacitance between the turns (“intra capacitance”) of the foil inductors is the reason for the deterioration of their properties at high frequencies. It is shown that the proposed filter has a natural cancellation of the intra capacitance. A hybrid LC filter may contain two or more foil layers isolated from each other and coiled on a core. The core material can be iron or even air as in the filter considered in this work. One of the foils, called the main foil, can be placed between the inverter and the motor cable. Other ones, called auxiliary foils, may be connected in star to create differential-mode noise paths, and then coupled to the DC link midpoint to guarantee a traveling path, especially for the common-mode currents. This way, there is a remarkable capacitance between the main foil and the auxiliary foil. Investigations showed that such a system can be described by a simple equivalent LC filter in a wide range of frequencies. Because of its simple hybrid construction, the proposed LC filter can be a cost-effective and competitive solution for modern power drives. In the thesis, the application field of the proposed filter is considered and determined. The basics of hybrid LC filter design are developed further. High-frequency behaviour of the proposed filter is analysed by simulations. Finally, the thesis presents experimental data proving that the hybrid LC filter can be used for du/dt of PWM pulses and reduction of common-mode currents.

On Fault Tolerance Methods for Networks-on-Chip

Technology scaling has proceeded into dimensions in which the reliability of manufactured devices is becoming endangered. The reliability decrease is a consequence of physical limitations, relative increase of variations, and decreasing noise margins, among others. A promising solution for bringing the reliability of circuits back to a desired level is the use of design methods which introduce tolerance against possible faults in an integrated circuit. This thesis studies and presents fault tolerance methods for network-onchip (NoC) which is a design paradigm targeted for very large systems-onchip. In a NoC resources, such as processors and memories, are connected to a communication network; comparable to the Internet. Fault tolerance in such a system can be achieved at many abstraction levels. The thesis studies the origin of faults in modern technologies and explains the classification to transient, intermittent and permanent faults. A survey of fault tolerance methods is presented to demonstrate the diversity of available methods. Networks-on-chip are approached by exploring their main design choices: the selection of a topology, routing protocol, and flow control method. Fault tolerance methods for NoCs are studied at different layers of the OSI reference model. The data link layer provides a reliable communication link over a physical channel. Error control coding is an efficient fault tolerance method especially against transient faults at this abstraction level. Error control coding methods suitable for on-chip communication are studied and their implementations presented. Error control coding loses its effectiveness in the presence of intermittent and permanent faults. Therefore, other solutions against them are presented. The introduction of spare wires and split transmissions are shown to provide good tolerance against intermittent and permanent errors and their combination to error control coding is illustrated. At the network layer positioned above the data link layer, fault tolerance can be achieved with the design of fault tolerant network topologies and routing algorithms. Both of these approaches are presented in the thesis together with realizations in the both categories. The thesis concludes that an optimal fault tolerance solution contains carefully co-designed elements from different abstraction levels

Effects of interband and intraband impurity scattering on coherence length in the pnictide superconductors

After discovery of cuprates, a search for new high temperature superconducting families began and it led to the discovery of layered pnictide compounds with critical temperatures limited up to ∼56 K. Pnictides consist elements from Group V of Periodic Table (nitrogen, phosphorus, arsenic, antimony and bismuth). In this work coherence length h in mixed state of pnictide superconductors is calculated numerically. In calculation is taken into account interband and intraband impurity scattering in framework of quasiclassical Eilenberger theory for s± pairing symmetry. Differences between Ginzburg-Landau and Eilenberger theories is shown and the comparison with existing models is done.