Reluktanssiverkkomalli kestomagneettitahtikoneen staattisen ilmavälivuontiheyden mallinnukseen

Kaikissa pyörivissä sähkömoottoreissa vääntömomentin tuoton kannalta olennainen magneettivuo kulkee staattorin ja roottorin välillä ilmavälin kautta. Ilmaväli mallinnetaan koneensuunnittelun yhteydessä tämän vuoksi tarkasti. Elementtimenetelmällä voidaan analysoida moottoreita varsin tarkasti, mutta menetelmän käyttö vie paljon aikaa ja sovittaminen muihin laskentaympäristöihin on usein hankalaa. Tämän vuoksi voidaan käyttää riittävän tarkkuuden omaavia analyyttisiä laskentamenetelmiä, joiden sovittaminen muihin ohjelmaympäristöihin on helpompaa kuin elementtimenetelmää käytettäessä. Diplomityössä kehitetään reluktanssiverkkomalli kestomagneettien aikaansaaman ilmavälivuontiheyden mallintamiseen kestomagneettitahtikoneille, joissa on pinta-asennetut kestomagneetit. Kehitetyn reluktanssiverkkomallin toimivuutta vertaillaan muihin ilmavälivuontiheyden laskentamenetelmiin.

A comparative performance study of four-pole induction motors and synchronous reluctance motors in variable speed drives

Design aspects of the Transversally Laminated Anisotropic (TLA) Synchronous Reluctance Motor (SynRM) are studied and the machine performance analysis compared to the Induction Motor (IM) is done. The SynRM rotor structure is designed and manufactured for a30 kW, four-pole, three-phase squirrel cage induction motor stator. Both the IMand SynRM were supplied by a sensorless Direct Torque Controlled (DTC) variablespeed drive. Attention is also paid to the estimation of the power range where the SynRM may compete successfully with a same size induction motor. A technicalloss reduction comparison between the IM and SynRM in variable speed drives is done. The Finite Element Method (FEM) is used to analyse the number, location and width of flux barriers used in a multiple segment rotor. It is sought for a high saliency ratio and a high torque of the motor. It is given a comparison between different FEM calculations to analyse SynRM performance. The possibility to take into account the effect of iron losses with FEM is studied. Comparison between the calculated and measured values shows that the design methods are reliable. A new application of the IEEE 112 measurement method is developed and used especially for determination of stray load losses in laboratory measurements. The study shows that, with some special measures, the efficiency of the TLA SynRM is equivalent to that of a high efficiency IM. The power factor of the SynRM at rated load is smaller than that of the IM. However, at lower partial load this difference decreases and this, probably, brings that the SynRM gets a better power factor in comparison with the IM. The big rotor inductance ratio of the SynRM allows a good estimating of the rotor position. This appears to be very advantageous for the designing of the rotor position sensor-less motor drive. In using the FEM designed multi-layer transversally laminated rotor with damper windings it is possible to design a directly network driven motor without degrading the motorefficiency or power factor compared to the performance of the IM.

Predicting the need for ditch network maintenance in drained peatland sites in Finland

Kunnostusojitustarpeen ennustaminen ojitusalueilla

Finnish oral history network

Reviews

The oral history network in the Nordic and Baltic context

Teemanumero

Performance Evaluation of Six-Sectored Configuration in Hexagonal WCDMA (UMTS) Cellular Network Layout

The objective of this master's thesis is to evaluate the optimum performance of sixsectored hexagonal layout of WCDMA (UMTS) network and analyze the performance at the optimum point. The maximum coverage and the maximum capacity are the main concern of service providers and it is always a challenging task for them to achieve economically. Because the optimum configuration of a network corresponds to a configuration which minimizes the number of sites required to provide a target service probability in the planning area which in turn reduces the deployment cost. The optimum performance means the maximum cell area and themaximum cell capacity the network can provide at the maximum antenna height satisfying the target service probability. Hexagon layout has been proven as the best layout for the cell deployment. In this thesis work, two different configurations using six-sectored sites have been considered for the performance comparison. In first configuration, each antenna is directed towards each corner of hexagon, whereas in second configurationeach antenna is directed towards each side of hexagon. The net difference in the configurations is the 30 degree rotation of antenna direction. The only indoor users in a flat and smooth semi-urban environment area have been considered for the simulation purpose where the traffic distribution is 100 Erl/km2 with 12.2 kbps speech service having maximum mobile speed of 3 km/hr. The simulation results indicate that a similar performance can be achieved in both the configurations, that is, a maximum of 947 m cellrange at antenna height of 49.5 m can be achieved when the antennas are directed towards the corner of hexagon, whereas 943.3 m cell range atantenna height of 54 m can be achieved when the antennas are directed towards the side of hexagon. However, from the interference point of view the first configuration provides better results. The simulation results also show that the network is coverage limited in both the uplink and downlink direction at the optimum point.

The electricity distribution network in Saint-Petersburg area and benchmark between Saint-Petersburg and City of Stockholm related distribution companies' performance

The main objective of the Thesis is the description of the electricity distribution networks in Saint-Petersburg area and Stockholm as well. Main similarity and differences in the construction and technicalperformance are presented in the study. Present and future development and investment into the electricity distribution network of OJSC Lenenergo are viewed. The Thesis presents the overview of the power industry reform in Russia. The current state of the electricity distribution sector is described. The study views the participation of the foreign investor "Fortum Power and Heat Oy" inthe development and management of the OJSC Lenenergo. Benchmark comparison of the prices and tangible assets of the main electricity distribution companies in Saint-Petersburg and Stockholm areas is done.

Developing of supplier network in shipbuilding industry

Työn tarkoituksena on selvittää minkälaisen verkoston Aker Yards Oy, kokonaistoimittajat ja kokonaistoimittajien alihankkijat muodostavat. Lisäksi arvioidaan verkostoriskit, joita Aker Yards Oy kohtaa toimiessaan verkostossa. Tutkimus suoritettiin tekemällä kysely verkostossa oleville kokonaistoimittajille sekä haastattelemalla kuutta henkilöä Aker Yards Oy:stä. Suhteita ja verkostoa analysoitiin tutkimalla verkoston yksittäisiä toimijoita sekä näiden välisiä suhteita. Riskejä analysoitiin tarkastelemalla niiden tunnistettuja syitä. Työn tuloksena on verkostokuva, joka piirrettiin kyselytulosten perusteella. Suhteiden ja verkoston analyysillä päädyttiin tehtäviin, joita Aker Yards Oy:n johdon tulisi toteuttaa, jotta verkostosta ja yksittäisistä toimittajista saataisiin irti mahdollisimman paljon. Lisäksi suhteita ja verkostoa käsiteltiin niiden tuloksellisen johtamisen näkökulmasta. Riskianalyysista saatiin tuloksena uhkaavimpien riskien arviointi.