Oxidation rates of carbon and nitrogen in char residues from solid fuels

Computational fluid dynamics (CFD) modeling is an important tool in designing new combustion systems. By using CFD modeling, entire combustion systems can be modeled and the emissions and the performance can be predicted. CFD modeling can also be used to develop new and better combustion systems from an economical and environmental point of view. In CFD modeling of solid fuel combustion, the combustible fuel is generally treated as single fuel particles. One of the limitations with the CFD modeling concerns the sub-models describing the combustion of single fuel particles. Available models in the scientific literature are in many cases not suitable as submodels for CFD modeling since they depend on a large number of input parameters and are computationally heavy. In this thesis CFD-applicable models are developed for the combustion of single fuel particles. The single particle models can be used to improve the combustion performance in various combustion devices or develop completely new technologies. The investigated fields are oxidation of carbon (C) and nitrogen (N) in char residues from solid fuels. Modeled char-C oxidation rates are compared to experimental oxidation rates for a large number of pulverized solid fuel chars under relevant combustion conditions. The experiments have been performed in an isothermal plug flow reactor operating at 1123-1673 K and 3-15 vol.% O2. In the single particle model, the char oxidation is based on apparent kinetics and depends on three fuel specific parameters: apparent pre-exponential factor, apparent activation energy, and apparent reaction order. The single particle model can be incorporated as a sub-model into a CFD code. The results show that the modeled char oxidation rates are in good agreement with experimental char oxidation rates up to around 70% of burnout. Moreover, the results show that the activation energy and the reaction order can be assumed to be constant for a large number of bituminous coal chars under conditions limited by the combined effects of chemical kinetics and pore diffusion. Based on this, a new model based on only one fuel specific parameter is developed (Paper III). The results also show that reaction orders of bituminous coal chars and anthracite chars differ under similar conditions (Paper I and Paper II); reaction orders of bituminous coal chars were found to be one, while reaction orders of anthracite chars were determined to be zero. This difference in reaction orders has not previously been observed in the literature and should be considered in future char oxidation models. One of the most frequently used comprehensive char oxidation models could not explain the difference in the reaction orders. In the thesis (Paper II), a modification to the model is suggested in order to explain the difference in reaction orders between anthracite chars and bituminous coal chars. Two single particle models are also developed for the NO formation and reduction during the oxidation of single biomass char particles. In the models the char-N is assumed to be oxidized to NO and the NO is partly reduced inside the particle. The first model (Paper IV) is based on the concentration gradients of NO inside and outside the particle and the second model is simplified to such an extent that it is based on apparent kinetics and can be incorporated as a sub-model into a CFD code (Paper V). Modeled NO release rates from both models were in good agreement with experimental measurements from a single particle reactor of quartz glass operating at 1173-1323 K and 3-19 vol.% O2. In the future, the models can be used to reduce NO emissions in new combustion systems.

Mass transfer and particleinteractions in granular systems and suspension flows

The purpose of this study was to investigate some important features of granular flows and suspension flows by computational simulation methods. Granular materials have been considered as an independent state ofmatter because of their complex behaviors. They sometimes behave like a solid, sometimes like a fluid, and sometimes can contain both phases in equilibrium. The computer simulation of dense shear granular flows of monodisperse, spherical particles shows that the collisional model of contacts yields the coexistence of solid and fluid phases while the frictional model represents a uniform flow of fluid phase. However, a comparison between the stress signals from the simulations and experiments revealed that the collisional model would result a proper match with the experimental evidences. Although the effect of gravity is found to beimportant in sedimentation of solid part, the stick-slip behavior associated with the collisional model looks more similar to that of experiments. The mathematical formulations based on the kinetic theory have been derived for the moderatesolid volume fractions with the assumption of the homogeneity of flow. In orderto make some simulations which can provide such an ideal flow, the simulation of unbounded granular shear flows was performed. Therefore, the homogeneous flow properties could be achieved in the moderate solid volume fractions. A new algorithm, namely the nonequilibrium approach was introduced to show the features of self-diffusion in the granular flows. Using this algorithm a one way flow can beextracted from the entire flow, which not only provides a straightforward calculation of self-diffusion coefficient but also can qualitatively determine the deviation of self-diffusion from the linear law at some regions nearby the wall inbounded flows. Anyhow, the average lateral self-diffusion coefficient, which was calculated by the aforementioned method, showed a desirable agreement with thepredictions of kinetic theory formulation. In the continuation of computer simulation of shear granular flows, some numerical and theoretical investigations were carried out on mass transfer and particle interactions in particulate flows. In this context, the boundary element method and its combination with the spectral method using the special capabilities of wavelets have been introduced as theefficient numerical methods to solve the governing equations of mass transfer in particulate flows. A theoretical formulation of fluid dispersivity in suspension flows revealed that the fluid dispersivity depends upon the fluid properties and particle parameters as well as the fluid-particle and particle-particle interactions.

Improvement of pyrolysis oil quality by scrubbing

Diplomityössä tutkittiin kuuman pyrolyysihöyryn puhdistamista haisevista ja kevyistä haihtuvista yhdisteistä. Työn kirjallisuusosassa selvitettiin pyrolyysiöljyn kannattavuutta uusiutuvana energialähteenä. Lisäksi eri pesurityyppejä tarkasteltiin ja ja vertailtiin. Työn kokeellisessa osassa käytettiin kahta erilaista koelaitteistoa. Tuotteen talteenotossa vertailtiin reaktorilämpötilan ja raaka-aineen kosteuden vaikutusta pyrolyysisaantoihin. Komponenttien talteenotossa tutkittiin epästabiilien ja pistävän hajuisten yhdisteiden poistamista kuumasta pyrolyysihöyrystä. Raaka-aineena käytettiin kuusen metsätäh-dehaketta, joka sisältää runsaasti neulasia ja kaarnaa. Kokeet toteutettiin lämpötila-alueella 460 - 520 °C. Koelaitteistot koostuivat kaasun (N2) syöttöjärjestelmään kytketystä kuumasta ja kyl-mästä puolesta. Tuotteen talteenotossa kuuma pyrolyysihöyry jäähdytettiin ja otettiin talteen. Komponenttien talteenotossa tuote kerättiin suodattimelle ja metyleeniklo-ridiloukkuun. Tuotteiden koostumukset analysoitiin kaasukromatokrafilla. Korkeimmat orgaaniset saannot saatiin 480 °C reaktorilämpötilalla ja 8-9 p-% raaka-ainekosteudella. Pyrolyysiveden määrä putosi raaka-aineen kosteutta nostettaessa. Eri reaktorilämpötiloilla ja raaka-ainekosteuksilla ei ollut vaikutusta hiiltosaantoihin. Kaasusaannot (pääosin CO2, CO ja hiilivedyt) olivat noin 10 p-%. Komponenttien talteenotossa suodatin tukkeutui matalissa (< 250 °C) lämpötiloissa. Suodattimelle jäänyt materiaali oli pääosin neulasista ja kaarnasta peräisin olevia uuteaineita (pääosin hartsi- rasvahappoja) ja sokereita. Korkeimmissa lämpötiloissa (> 250 °C) uuteaineet läpäisivät suodattimen paremmin. 250 ja 300 °C:n lämpötiloissa suuri määrä lyhytketjuisia helposti haihtuvia epästabiileja ja haisevia yhdisteitä (ketoneja, furaani- ja furfuraalijohdannaisia jne.) jäi metyleenikloridi- ja metanoliloukkuihin.

Kiinteäkerroskaasuttimen toiminnan teoreettinen tarkastelu ja puupellettien kaasutuskokeet myötävirtareaktorilla

Tämä työ on osa tutkimusprojektia, jonka tarkoituksena on kehittää uudentyyppinen kaasutustekniikkaan perustuva kiinteistöjen lämmitysjärjestelmä. Työ on tehty osaksi kirjallisuustutkimuksena käyttämällä hyödyksi alalla tehtyjä tutkimuksia ja kirjallisuutta. Kirjallisuustutkimuksen tavoitteena oli luoda yhtenäinen tietopaketti lämmitysjärjestelmän kehityksen tueksi. Työn kokeellisen osion tavoitteena oli tutkia lämmitysjärjestelmän kaasuttimen prototyypin toimintaa ja selvittää sen käyttöön liittyviä ongelmia. Kirjallisuusosiossa käsitellään kaasutuksen vaiheita: alkulämpeneminen ja kuivuminen, syttyminen, pyrolyysi sekä jäännöshiilen palaminen ja kaasutus. Varsinkin pyrolyysiprosessin tunteminen on merkittävää, kun halutaan parantaa biomassan poltto- ja kaasutusprosessien suunnittelua. Lisäksi kirjallisuusosiossa käsitellään kaasutuksessa syntyvän tuotekaasun ominaisuuksia: koostumus, lämpöarvo, tiheys ja palamisominaisuudet. Tuotekaasun ominaisuudet vaihtelevat suuresti kaasutusprosessista ja -olosuhteista sekä polttoaineesta riippuen. Tuotekaasun kohdalta käsitellään myös sen käyttökohteita. Perinteisesti kaasutuksen tuotekaasua käytetään lämmöntuotantoon, mutta tulevaisuuden haasteena on tuotekaasun käyttö kaasuturbiineissa sähköntuotantoon. Tuotekaasun käyttöä laajemmin rajoittaa sen sisältämät epäpuhtaudet. Tämän vuoksi kirjallisuusosiossa käsitellään myös tuotekaasun puhdistusmenetelmiä ja sen poltossa syntyvien päästöjen vähentämiskeinoja. Kokeellisessa osiossa suoritettiin puupellettien kaasutuskokeita TTKK:n Energia- ja prosessitekniikan laitoksen raskaaseen laboratorioon rakennetulla kaasutusreaktorilla. Kaasutuskokeiden avulla löydettiin kaasutusreaktorin toiminnan ongelmakohdat ja pystyttiin aloittamaan lämmitysjärjestelmän jatkokehitys.

Jäännöshiilen ja kalkkikiven reaktiokinetiikan mallinnus kiertoleijukattilan tulipesässä

Työn tavoitteena oli kehittää mallit jäännöshiilen ja kalkkikiven reaktiokinetiikan sekä jäännöshiilen jauhautumisen ennustamiseksi kiertoleijukattilan tulipesässä. Kehitetyt mallit toimivat tulipesämallin osamalleina. Perustuen mallinnettuihin reaktionopeuksiin ja jauhautumiskäyttäytymiseen tulipesämalli ennustaa kalkkikivihiukkasten rikinsidonnan ja jäännöshiilen jakautumisen erikokoisiksi hiukkasiksi tulipesässä ja tuhkissa. Työssä kehitetyt mallit perustuvat olemassa oleviin kalkkikiven ja polttoaineen reaktiivisuustesteihin laboratorio-kokoluokan leijukerrosreaktorissa. Mallit huomioivat myös tulipesän olosuhteet. Menetelmät kelpoistettiin onnistuneesti kaupallisen kokoluokan kiertoleijukattiloista mitattujen ja tulipesämallilla laskettujen taseiden avulla. Mallien kehittämistä tullaan jatkamaan.

Muutosilmiöt soodakattilakeossa

Soodakattilan sulakeon epästationaarinen käyttäytyminen sekä keon pitkä jäähtymisaika alasajon jälkeen ovat aiheuttaneet ongelmia kattilan taloudellisessa käytettävyydessä. Keon käyttäytymisestä on luotu CFD-malleja, joiden tavoitteena on havainnollistaa keon lämpötilajakaumaa ja rakennetta. Mallien ongelmana on se, että niissä huomioidaan vain keon aktiivinen pintakerros. Keon sisäosan rakennetta ja siinä tapahtuvia prosesseja ei toistaiseksi tunneta kunnolla luotettavan, koko keon kattavan mallin luomiseen. Tässä työssä tutkittiin sulakeon käytön aikana havaittuja muutosilmiöitä, jotka vaikuttavat keon rakenteeseen ja ominaisuuksiin sekä tutkittiin ilmiöiden taustalla olevia tekijöitä. Näitä tekijöitä ovat keon sisässä tapahtuvat kemialliset ja fyysiset prosessit, jotka aiheuttavat muutoksia niin lämpöteknisesti kuin fyysisesti sekä ulkoapäin tulevat tekijät, jotka aiheutuvat ajotilanteiden seurauksena tapahtuvista muutoksista. Työn kokeellisena osana luotiin sulakeon jäähtymismalli käyttäen 1-dimensionaalista ADL-mallia. Mallin pohjana käytettiin StoraEnso Oy:ltä Oulun soodakattilan sulakeosta saatua mittausraporttia. ADL-mallin avulla luotiin keon jäähtymiskäyrät lämpötilan ja syvyyden funktiona. Saadut käyrät täsmäsivät hyvin mittausraportin tuloksiin. Mallin avulla keolle saatiin muodostettua energiatase, jonka tuloksena keosta 12 tunnin aikana poistuva lämpövirta pinnalla oli noin 9.8kW/m2 ja pinnan lämmönsiirtokerroin 58.3W/m²°C. Pohjan poistuvaksi lämpövirraksi saatiin 14.1kW/m2 ja lämmönsiirtokertoimeksi 75.4W/m²°C. Termiseksi diffuusiokertoimeksi saatiin 3.9•10-7m²/s.

A study of combustion phenomena in circulating fluidized beds by developing and applying experimental and modelling methods for laboratory-scale reactors

The results shown in this thesis are based on selected publications of the 2000s decade. The work was carried out in several national and EC funded public research projects and in close cooperation with industrial partners. The main objective of the thesis was to study and quantify the most important phenomena of circulating fluidized bed combustors by developing and applying proper experimental and modelling methods using laboratory scale equipments. An understanding of the phenomena plays an essential role in the development of combustion and emission performance, and the availability and controls of CFB boilers. Experimental procedures to study fuel combustion behaviour under CFB conditions are presented in the thesis. Steady state and dynamic measurements under well controlled conditions were carried out to produce the data needed for the development of high efficiency, utility scale CFB technology. The importance of combustion control and furnace dynamics is emphasized when CFB boilers are scaled up with a once through steam cycle. Qualitative information on fuel combustion characteristics was obtained directly by comparing flue gas oxygen responses during the impulse change experiments with fuel feed. A one-dimensional, time dependent model was developed to analyse the measurement data Emission formation was studied combined with fuel combustion behaviour. Correlations were developed for NO, N2O, CO and char loading, as a function of temperature and oxygen concentration in the bed area. An online method to characterize char loading under CFB conditions was developed and validated with the pilot scale CFB tests. Finally, a new method to control air and fuel feeds in CFB combustion was introduced. The method is based on models and an analysis of the fluctuation of the flue gas oxygen concentration. The effect of high oxygen concentrations on fuel combustion behaviour was also studied to evaluate the potential of CFB boilers to apply oxygenfiring technology to CCS. In future studies, it will be necessary to go through the whole scale up chain from laboratory phenomena devices through pilot scale test rigs to large scale, commercial boilers in order to validate the applicability and scalability of the, results. This thesis shows the chain between the laboratory scale phenomena test rig (bench scale) and the CFB process test rig (pilot). CFB technology has been scaled up successfully from an industrial scale to a utility scale during the last decade. The work shown in the thesis, for its part, has supported the development by producing new detailed information on combustion under CFB conditions.

Virtual Professional Network as a Value Creator in the Dental Business

The research of virtual professional networks has been enormous but the lack of research in the dental field was obvious. This study focuses on those uses and gratifications, and motives of participants that a virtual pro-fessional network should fulfil. The aim of this study is to understand the factors behind the successful virtual professional network, and motives of participants that support a particular business network’s building up for contributing its further success. In this study the focus is on particular mo-tives, needs and benefits of participants that are significant for the net-work’s further development. The study will explore relevant scientific research and theory that is char-acteristic in networking, and theories of user’s needs and motives. Empiri-cal data was collected from dental professionals by net based question-naire that was sent by e-mail. Data analysis was done by quantitative fac-tor analysis. The findings of this study were obvious that virtual knowledge of implantology is inadequate and knowledge is rather difficult to find in the Internet. Sharing of virtual knowledge, net-learning and communication were seen to improve the quality of impolantological professionalism and also the development of these areas was experienced essential. On the grounds of this study a host of a virtual professional network can focus on those aspects that serve the users at best, can develop professionalism in implantology and can profit in its own business operations.

Production of Biofuels by Fischer Tropsch Synthesis

Production of biofuel via biomass gasification followed by Fischer Tropsch synthesis is of considerable interest because of the high quality of fuels produced which do not contain sulphur and are free of carbon dioxide. The purpose of this Master’s thesis is to study feasibility production of biofuels integrated with Fischer Tropsch process using Aspen Plus simulation. The simulation results were used to size process equipment and carry out an economic evaluation. The results show that lowering the reactor temperature from 1000 oC - 850 oC and raising the water gas shift temperature from 500 oC - 600 oC can improve overall gas efficiency, which in turn leads to better production of ultra clean syngas for the Fischer Tropsch synthetic reactor. Similarly, the Fischer Tropsch offgas is converted into a gas turbine for power production, and finally biodiesel is produced as fuels for transportation.

Solids removal in pyrolysis

Pyrolysis is a process for turning biomass into liquid fuel. The process consists of heating the biomass in inert conditions and quenching the resulting vapors into oil. The oil has many potential uses, such as heating fuel in peak heating plants. In order to broaden the application base and improve the quality of the oil, solids removal has to be addressed. The solids may also increase the probability of plugging in downstream equipment. The purpose of this research was to gain an understanding of the formation of solids in the pyrolysis process and to assess options for reducing the solid content of the oil. From literature it is known that the solids can be removed either by hot vapor filtration, liquid treatment or multiple cyclones. Hot vapor filtration decreases yield, but improves the stability of the oil while simultaneously removing solids and ash. Liquid treatment techniques are good for removing large particles but involve losses of pyrolysis liquid. Cyclones are a traditional robust technique used regularly in pyrolysis. In the experimental part of this thesis, a 2 MWfuel pyrolysis setup with 2 cyclones in series was operated and monitored. Solid and liquid samples were collected from various parts of the process for further examination. Sampling and sample treatment techniques were developed. The chemical properties of the pyrolysis char were also analyzed and assessed as a function of reactor temperature and fluidizing velocity. By measuring the particle size distributions it was noticed that there were much smaller particles collected from the second cyclone than fed into pyrolysis. The solids in the pyrolysis oil were even smaller. This was most likely caused by attrition and shrinkage. Due to better separation efficiency of the cyclones in large particles, excess attrition should be avoided.

Modeling of fireside deposit formation in two industrial furnaces

Fireside deposits can be found in many types of utility and industrial furnaces. The deposits in furnaces are problematic because they can reduce heat transfer, block gas paths and cause corrosion. To tackle these problems, it is vital to estimate the influence of deposits on heat transfer, to minimize deposit formation and to optimize deposit removal. It is beneficial to have a good understanding of the mechanisms of fireside deposit formation. Numerical modeling is a powerful tool for investigating the heat transfer in furnaces, and it can provide valuable information for understanding the mechanisms of deposit formation. In addition, a sub-model of deposit formation is generally an essential part of a comprehensive furnace model. This work investigates two specific processes of fireside deposit formation in two industrial furnaces. The first process is the slagging wall found in furnaces with molten deposits running on the wall. A slagging wall model is developed to take into account the two-layer structure of the deposits. With the slagging wall model, the thickness and the surface temperature of the molten deposit layer can be calculated. The slagging wall model is used to predict the surface temperature and the heat transfer to a specific section of a super-heater tube panel with the boundary condition obtained from a Kraft recovery furnace model. The slagging wall model is also incorporated into the computational fluid dynamics (CFD)-based Kraft recovery furnace model and applied on the lower furnace walls. The implementation of the slagging wall model includes a grid simplification scheme. The wall surface temperature calculated with the slagging wall model is used as the heat transfer boundary condition. Simulation of a Kraft recovery furnace is performed, and it is compared with two other cases and measurements. In the two other cases, a uniform wall surface temperature and a wall surface temperature calculated with a char bed burning model are used as the heat transfer boundary conditions. In this particular furnace, the wall surface temperatures from the three cases are similar and are in the correct range of the measurements. Nevertheless, the wall surface temperature profiles with the slagging wall model and the char bed burning model are different because the deposits are represented differently in the two models. In addition, the slagging wall model is proven to be computationally efficient. The second process is deposit formation due to thermophoresis of fine particles to the heat transfer surface. This process is considered in the simulation of a heat recovery boiler of the flash smelting process. In order to determine if the small dust particles stay on the wall, a criterion based on the analysis of forces acting on the particle is applied. Time-dependent simulation of deposit formation in the heat recovery boiler is carried out and the influence of deposits on heat transfer is investigated. The locations prone to deposit formation are also identified in the heat recovery boiler. Modeling of the two processes in the two industrial furnaces enhances the overall understanding of the processes. The sub-models developed in this work can be applied in other similar deposit formation processes with carefully-defined boundary conditions.

Industrial-Scale hydrothermal carbonization of waste sludge materials for fuel production

Hydrothermal carbonization (HTC) is a thermochemical process used in the production of charred matter similar in composition to coal. It involves the use of wet, carbohydrate feedstock, a relatively low temperature environment (180 °C-350 °C) and high autogenous pressure (up to 2,4 MPa) in a closed system. Various applications of the solid char product exist, opening the way for a range of biomass feedstock materials to be exploited that have so far proven to be troublesome due to high water content or other factors. Sludge materials are investigated as candidates for industrial-scale HTC treatment in fuel production. In general, HTC treatment of pulp and paper industry sludge (PPS) and anaerobically digested municipal sewage sludge (ADS) using existing technology is competitive with traditional treatment options, which range in price from EUR 30-80 per ton of wet sludge. PPS and ADS can be treated by HTC for less than EUR 13 and 33, respectively. Opportunities and challenges related to HTC exist, as this relatively new technology moves from laboratory and pilot-scale production to an industrial scale. Feedstock materials, end-products, process conditions and local markets ultimately determine the feasibility of a given HTC operation. However, there is potential for sludge materials to be converted to sustainable bio-coal fuel in a Finnish context.

Teollinen symbioosi - kansallisen ohjelman toteuttaminen Suomessa Britanniaan verrattuna

This master thesis examines the possibility of implementing a national industrial symbiosis programme in Finland. Industrial symbiosis is a close cooperation between companies in which the actors make use of each other's wastes and by-products as raw materials for pro-cesses. Symbiosis programme aims to promote industrial symbiosis by identifying possible synergies. In the United Kingdom (UK), a national level programme NISP (National Industri-al Symbiosis Programme) has been successfully implemented. This thesis studies whether it would be possible to implement a similar program in Finland. The implementation of the pro-gram in Finland is evaluated by analyzing and comparing Finnish and British business envi-ronments using PESTEL and diamond models. The goal is to identify factors that promote or hinder the implementation of the programme in Finland. Based on this study, it can be said that implementing the programme in Finland is possible. The programme can be carried out in almost the same principles as in the UK, but some char-acteristics of the Finnish business environment, such as the high level of technological know-how, should especially be taken as an advantage. On the other hand, there are features, such as low level domestic demand, which may prevent the implementation of the program unless they are given special attention.

Behavior of black liquor nitrogen in combustion : formation of cyanate

The Kraft pulping process is the dominant chemical pulping process in the world. Roughly 195 million metric tons of black liquor are produced annually as a by-product from the Kraft pulping process. Black liquor consists of spent cooking chemicals and dissolved organics from the wood and can contain up to 0.15 wt% nitrogen on dry solids basis. The cooking chemicals from black liquor are recovered in a chemical recovery cycle. Water is evaporated in the first stage of the chemical recovery cycle, so the black liquor has a dry solids content of 65-85% prior to combustion. During combustion of black liquor, a portion of the black liquor nitrogen is volatilized, finally forming N2 or NO. The rest of the nitrogen remains in the char as char nitrogen. During char conversion, fixed carbon is burned off leaving the pulping chemicals as smelt, and the char nitrogen forms mostly smelt nitrogen (cyanate, OCN-). Smelt exits the recovery boiler and is dissolved in water. The cyanate from smelt decomposes in the presence of water, forming NH3, which causes nitrogen emissions from the rest of the chemical recovery cycle. This thesis had two focuses: firstly, to determine how the nitrogen chemistry in the recovery boiler is affected by modification of black liquor; and secondly, to find out what causes cyanate formation during thermal conversion, and which parameters affect cyanate formation and decomposition during thermal conversion of black liquor. The fate of added biosludge nitrogen in chemical recovery was determined in Paper I. The added biosludge increased the nitrogen content of black liquor. At the pulp mill, the added biosludge did not increase the NO formation in the recovery boiler, but instead increased the amount of cyanate in green liquor. The increased cyanate caused more NH3 formation, which increased the NCG boiler’s NO emissions. Laboratory-scale experiments showed an increase in both NO and cyanate formation after biosludge addition. Black liquor can be modified, for example by addition of a solid biomass to increase the energy density of black liquor, or by separation of lignin from black liquor by precipitation. The precipitated lignin can be utilized in the production of green chemicals or as a fuel. In Papers II and III, laboratory-scale experiments were conducted to determine the impact of black liquor modification on NO and cyanate formation. Removal of lignin from black liquor reduced the nitrogen content of the black liquor. In most cases NO and cyanate formation decreased with increasing lignin removal; the exception was NO formation from lignin lean soda liquors. The addition of biomass to black liquor resulted in a higher nitrogen content fuel mixture, due to the higher nitrogen content of biomass compared to black liquor. More NO and cyanate were formed from the fuel mixtures than from pure black liquor. The increased amount of formed cyanate led to the hypothesis that black liquor is catalytically active and converts a portion of the nitrogen in the mixed fuel to cyanate. The mechanism behind cyanate formation during thermal conversion of black liquor was not clear before this thesis. Paper IV studies the cyanate formation of alkali metal loaded fuels during gasification in a CO2 atmosphere. The salts K2CO3, Na2CO3, and K2SO4 all promoted char nitrogen to cyanate conversion during gasification, while KCl and CaCO3 did not. It is now assumed that cyanate is formed when alkali metal carbonate or an active intermediate of alkali metal carbonate (e.g. -CO2K) reacts with the char nitrogen forming cyanate. By testing different fuels (bark, peat, and coal), each of which had a different form of organic nitrogen, it was concluded that the form of organic nitrogen in char also has an impact on cyanate formation. Cyanate can be formed during pyrolysis of black liquor, but at temperatures 900°C or above, the formed cyanate will decompose. Cyanate formation in gasifying conditions with different levels of CO2 in the atmosphere was also studied. Most of the char nitrogen was converted to cyanate during gasification at 800-900°C in 13-50% CO2 in N2, and only 5% of the initial fuel nitrogen was converted to NO during char conversion. The formed smelt cyanate was stable at 800°C 13% CO2, while it decomposed at 900°C 13% CO2. The cyanate decomposition was faster at higher temperatures and in oxygen-containing atmospheres than in an inert atmosphere. The presence of CO2 in oxygencontaining atmospheres slowed down the decomposition of cyanate. This work will provide new information on how modification of black liquor affects the nitrogen chemistry during thermal conversion of black liquor and what causes cyanate formation during thermal conversion of black liquor. The formation and decomposition of cyanate was studied in order to provide new data, which would be useful in modeling of nitrogen chemistry in the recovery boiler.

Heterogeneous mass transfer in fluidized beds by computational fluid dynamics

The main objective of this research is to estimate and characterize heterogeneous mass transfer coefficients in bench- and pilot-scale fluidized bed processes by the means of computational fluid dynamics (CFD). A further objective is to benchmark the heterogeneous mass transfer coefficients predicted by fine-grid Eulerian CFD simulations against empirical data presented in the scientific literature. First, a fine-grid two-dimensional Eulerian CFD model with a solid and gas phase has been designed. The model is applied for transient two-dimensional simulations of char combustion in small-scale bubbling and turbulent fluidized beds. The same approach is used to simulate a novel fluidized bed energy conversion process developed for the carbon capture, chemical looping combustion operated with a gaseous fuel. In order to analyze the results of the CFD simulations, two one-dimensional fluidized bed models have been formulated. The single-phase and bubble-emulsion models were applied to derive the average gas-bed and interphase mass transfer coefficients, respectively. In the analysis, the effects of various fluidized bed operation parameters, such as fluidization, velocity, particle and bubble diameter, reactor size, and chemical kinetics, on the heterogeneous mass transfer coefficients in the lower fluidized bed are evaluated extensively. The analysis shows that the fine-grid Eulerian CFD model can predict the heterogeneous mass transfer coefficients quantitatively with acceptable accuracy. Qualitatively, the CFD-based research of fluidized bed process revealed several new scientific results, such as parametrical relationships. The huge variance of seven orders of magnitude within the bed Sherwood numbers presented in the literature could be explained by the change of controlling mechanisms in the overall heterogeneous mass transfer process with the varied process conditions. The research opens new process-specific insights into the reactive fluidized bed processes, such as a strong mass transfer control over heterogeneous reaction rate, a dominance of interphase mass transfer in the fine-particle fluidized beds and a strong chemical kinetic dependence of the average gas-bed mass transfer. The obtained mass transfer coefficients can be applied in fluidized bed models used for various engineering design, reactor scale-up and process research tasks, and they consequently provide an enhanced prediction accuracy of the performance of fluidized bed processes.