Torque vibration model of axial-flux surface-mounted permanent magnet synchronous machine

In order that the radius and thus ununiform structure of the teeth and otherelectrical and magnetic parts of the machine may be taken into consideration the calculation of an axial flux permanent magnet machine is, conventionally, doneby means of 3D FEM-methods. This calculation procedure, however, requires a lotof time and computer recourses. This study proves that also analytical methods can be applied to perform the calculation successfully. The procedure of the analytical calculation can be summarized into following steps: first the magnet is divided into slices, which makes the calculation for each section individually, and then the parts are submitted to calculation of the final results. It is obvious that using this method can save a lot of designing and calculating time. Thecalculation program is designed to model the magnetic and electrical circuits of surface mounted axial flux permanent magnet synchronous machines in such a way, that it takes into account possible magnetic saturation of the iron parts. Theresult of the calculation is the torque of the motor including the vibrations. The motor geometry and the materials and either the torque or pole angle are defined and the motor can be fed with an arbitrary shape and amplitude of three-phase currents. There are no limits for the size and number of the pole pairs nor for many other factors. The calculation steps and the number of different sections of the magnet are selectable, but the calculation time is strongly depending on this. The results are compared to the measurements of real prototypes. The permanent magnet creates part of the flux in the magnetic circuit. The form and amplitude of the flux density in the air-gap depends on the geometry and material of the magnetic circuit, on the length of the air-gap and remanence flux density of the magnet. Slotting is taken into account by using the Carter factor in the slot opening area. The calculation is simple and fast if the shape of the magnetis a square and has no skew in relation to the stator slots. With a more complicated magnet shape the calculation has to be done in several sections. It is clear that according to the increasing number of sections also the result will become more accurate. In a radial flux motor all sections of the magnets create force with a same radius. In the case of an axial flux motor, each radial section creates force with a different radius and the torque is the sum of these. The magnetic circuit of the motor, consisting of the stator iron, rotor iron, air-gap, magnet and the slot, is modelled with a reluctance net, which considers the saturation of the iron. This means, that several iterations, in which the permeability is updated, has to be done in order to get final results. The motor torque is calculated using the instantaneous linkage flux and stator currents. Flux linkage is called the part of the flux that is created by the permanent magnets and the stator currents passing through the coils in stator teeth. The angle between this flux and the phase currents define the torque created by the magnetic circuit. Due to the winding structure of the stator and in order to limit the leakage flux the slot openings of the stator are normally not made of ferromagnetic material even though, in some cases, semimagnetic slot wedges are used. In the slot opening faces the flux enters the iron almost normally (tangentially with respect to the rotor flux) creating tangential forces in the rotor. This phenomenon iscalled cogging. The flux in the slot opening area on the different sides of theopening and in the different slot openings is not equal and so these forces do not compensate each other. In the calculation it is assumed that the flux entering the left side of the opening is the component left from the geometrical centre of the slot. This torque component together with the torque component calculated using the Lorenz force make the total torque of the motor. It is easy to assume that when all the magnet edges, where the derivative component of the magnet flux density is at its highest, enter the slot openings at the same time, this will have as a result a considerable cogging torque. To reduce the cogging torquethe magnet edges can be shaped so that they are not parallel to the stator slots, which is the common way to solve the problem. In doing so, the edge may be spread along the whole slot pitch and thus also the high derivative component willbe spread to occur equally along the rotation. Besides forming the magnets theymay also be placed somewhat asymmetric on the rotor surface. The asymmetric distribution can be made in many different ways. All the magnets may have a different deflection of the symmetrical centre point or they can be for example shiftedin pairs. There are some factors that limit the deflection. The first is that the magnets cannot overlap. The magnet shape and the relative width compared to the pole define the deflection in this case. The other factor is that a shifting of the poles limits the maximum torque of the motor. If the edges of adjacent magnets are very close to each other the leakage flux from one pole to the other increases reducing thus the air-gap magnetization. The asymmetric model needs some assumptions and simplifications in order to limit the size of the model and calculation time. The reluctance net is made for symmetric distribution. If the magnets are distributed asymmetrically the flux in the different pole pairs will not be exactly the same. Therefore, the assumption that the flux flows from the edges of the model to the next pole pairs, in the calculation model from one edgeto the other, is not correct. If it were wished for that this fact should be considered in multi-pole pair machines, this would mean that all the poles, in other words the whole machine, should be modelled in reluctance net. The error resulting from this wrong assumption is, nevertheless, irrelevant.

Field Weakening, Parameters and Operation Range of the Permanent Magnet Traction Motors

The main focus of this thesis is to define the field weakening point of permanent magnet synchronous machine with embedded magnets in traction applications. Along with the thesis a modelling program is made to help the designer to define the field weakening point in practical applications. The thesis utilizes the equations based on the current angle. These equations can be derived from the vector diagram of permanent magnet synchronous machine. The design parameters of the machine are: The maximum rotational speed, saliency ratio, maximum induced voltage and characteristic current. The main result of the thesis is finding out the rated rotational speed, from which the field weakening starts. The action of the machine is estimated at a wide speed range and the changes of machine parameters are examined.

Analytic evaluation of three-phase short circuit demagnetization and hysteresis loss risk in rotor-surface-magnet Permanent-Magnet Synchronous Machines

Permanent magnet synchronous machines (PMSM) have become widely used in applications because of high efficiency compared to synchronous machines with exciting winding or to induction motors. This feature of PMSM is achieved through the using the permanent magnets (PM) as the main excitation source. The magnetic properties of the PM have significant influence on all the PMSM characteristics. Recent observations of the PM material properties when used in rotating machines revealed that in all PMSMs the magnets do not necessarily operate in the second quadrant of the demagnetization curve which makes the magnets prone to hysteresis losses. Moreover, still no good analytical approach has not been derived for the magnetic flux density distribution along the PM during the different short circuits faults. The main task of this thesis is to derive simple analytical tool which can predict magnetic flux density distribution along the rotor-surface mounted PM in two cases: during normal operating mode and in the worst moment of time from the PM’s point of view of the three phase symmetrical short circuit. The surface mounted PMSMs were selected because of their prevalence and relatively simple construction. The proposed model is based on the combination of two theories: the theory of the magnetic circuit and space vector theory. The comparison of the results in case of the normal operating mode obtained from finite element software with the results calculated with the proposed model shows good accuracy of model in the parts of the PM which are most of all prone to hysteresis losses. The comparison of the results for three phase symmetrical short circuit revealed significant inaccuracy of the proposed model compared with results from finite element software. The analysis of the inaccuracy reasons was provided. The impact on the model of the Carter factor theory and assumption that air have permeability of the PM were analyzed. The propositions for the further model development are presented.

Calculation and comparison of different permanent sample plot types

Summary

A method for using random parameters in analyzing permanent sample plots

Summary

Natural development of stand structure in peatland Scots pine following drainage : results based on long-term monitoring of permanent sample plots

Abstract

Vendor Managed Inventory: the Critical Success Factors from the Manufacturer Point of View

Yritykset ovat pakotettuja erilaisiin yhteistyömuotoihin pärjätäkseen kiristyvässä kilpailussa. Yhteistyösuhteet kulkevat eri nimillä riippuen teollisuuden alasta ja siitä, missä kohtaa toimitusketjua ne toteutuvat, mutta periaatteessa kaikki pohjautuvat samaan ideaan kuin Vendor Managed Inventory (VMI); varastoon jakysyntään liittyvä tieto jaetaan toimitusketjun eri osapuolien kesken, jotta tuotanto, jakelu ja varastonhallinta olisi mahdollista optimoida. Vendor Managed Inventory on ideana yksinkertainen, mutta vaatii onnistuakseen paljon. Perusolettamus on, että toimittajan on kyettävä hallinnoimaan asiakkaan varastoa paremmin kuin asiakas itse. Tämä ei kuitenkaan ole mahdollista ilman riittävää yhteistyötä, oikeanlaista informaatiota tai sopivia tuoteominaisuuksia. Tämän työn tarkoitus on esitellä kriittiset menestystekijät valmistajan kannalta, kun näkyvyys todelliseen kysyntään on heikko ja kyseessäolevat tuotteet ovat ominaisuuksiltaan toimintamalliin huonosti soveltuvia. VMItoimintamallin soveltuvuus matkapuhelimia valmistavan yrityksen liiketoimintaan, sekä sen vaikutus asiakasyhteistyöhön, kannattavuuteen ja toiminnan tehostamiseen on myös tutkittu.

The structure and development of Russia's food retail sector from the point of view of Finnish food industry

Tämän diplomityön tavoitteena on selvittää Venäjän ruoan vähittäiskaupan rakenne ja sen tuleva kehitys. Tällä hetkellä se on yksi maailman nopeimmin kasvavista markkinoista. Kasvun syynä on korkea öljyn hinta, jokaon kumuloitunut ihmisten palkkoihin. Kuitenkin vaikka tulot kasvavat, ruokaan käytetty osuus tuloista on pysynyt suhteellisen vakaana. Kulutus on siis siirtymässä laadukkaampiin ja arvokkaampiin tuotteisiin Modernien kauppojen osuus markkinoista on vielä pieni, koska Venäjän vähittäiskauppasektori on yhä hajaantunut perinteisiin kauppaformaatteihin kuten kioskeihin, toreille ja pieniin ruokakauppoihin. Kauppaketjut ovat kuitenkin tulossa merkittävämmiksi. Suurin markkina-alue vähittäiskauppiaille on Moskova, mutta tällä hetkellä ketjut laajentavat toimintojaan nopeasti myös muille Venäjän alueille. Parhaat kasvunäkymät ovat alueilla, vaikka Moskovan markkinat eivät olekaan kyllästyneet. Tärkein kasvua rajoittava tekijä Moskovassa on rakennustonttien ja kiinteistöjen saatavuus. Vähittäiskauppamarkkinat lähestyvät kyllästymispistettä, josta seuraa markkinoiden konsolidaatio. Tämä prosessi on jo alkanut, mutta kovin paljon yritysostoja ei ole vielätehty. Toistaiseksi kauppaketjut ovat tyytyneet muodostamaan alliansseja. Ketjut pyrkivät parantamaan asemaansa hintaneuvotteluissa muodostamalla osto-alliansseja, luomalla omia brändejä ja käyttämällä alueellista laajentumista lyömäaseena. Jotta ruoan tuottaja pääsisi myös alueellisille markkinoille, on sen ehkä suostuttava myymään tuotteitaan edullisempaan hintaan. Tavarantoimittajat ovat vahvassa asemassa silloin, kun heillä on toimiva jakeluverkko, kyky JIT-toimituksiin,kunnollinen dokumentaatiokäytäntö, vahva brändi ja edullinen hinta. Ns. listausmaksun suuruus voi määrittää tuottajan tuotteilleen saaman hyllytilan koon.

Unlicensed Mobile Access Concept from Testing Point of View

Viime vuosikymmenien aikana kommunikaatioteknologiat ovat kehittyneet erittäin paljon. Uusia verkkoja, liityntätekniikoita, protokollia ja päätelaitteita on luotu alati kehittyvällä vauhdilla, eikä hidastumisen merkkejä ole näkyvissä. Varsinkin mobiilisovellukset ovat kasvattaneet markkinaosuuksiaan viime aikoina. Unlicensed MobileAccess (UMA) on uusi liityntätekniikka mobiilipäätelaitteille, joka mahdollistaa liitynnän GSM- runkoverkkoon WLAN- tai Bluetooth - tekniikoiden avulla. Tämä diplomityö keskittyy UMAan liittyviin teknologioihin, joita tarkastellaan lähemmin ensimmäisissä kappaleissa. Tavoitteena on esitellä, mitä UMA merkitsee, ja kuinka eri tekniikoita voidaan soveltaa sen toteutuksissa. Ennenkuin uusia teknologioita voidaan soveltaa kaupallisesti, täytyy niiden olla kokonaisvaltaisesti testattuja. Erilaisia testausmenetelmiä sovelletaan laitteistonja ohjelmiston testaukseen, mutta tavoite on kuitenkin sama, eli vähentää testattavan tuotteen epäluotettavuutta ja lisätä sen laatua. Vaikka UMA käsittääkin pääasiassa jo olemassa olevia tekniikoita, tuo se silti mukanaan uuden verkkoelementin ja kaksi uutta kommunikaatioprotokollaa. Ennen kuin mitään UMAa tukevia ratkaisuja voidaan tuoda markkinoille, monia erilaisia testausmenetelmiä on suoritettava, jotta varmistutaan uuden tuotteen oikeasta toiminnallisuudesta. Koska tämä diplomityö käsittelee uutta tekniikkaa, on myös testausmenetelmien yleisen testausteorian käsittelemiselle varattu oma kappale. Kappale esittelee erilaisia testauksen näkökulmia ja niihin perustuen rakennetaan myös testausohjelmisto. Tavoitteena on luoda ohjelmisto, jota voidaan käyttää UMA-RR protokollan toiminnan varmentamiseen kohdeympäristössä.

The Boundaries of the Firm from the Extended Transaction Cost Economics Point of View - Empirical Study

Tutkimuksen tavoitteena oli tutkia yrityksen rajoja laajennetun transaktiokustannusteorian näkökulmasta. Tutkimus oli empiirinen tutkimus, jossa tutkittiin viittä toimialaa. Tutkimuksen tavoitteena oli verrata paperiteollisuutta teräs-, kemian-, ICT- ja energiateollisuuteen. Aineisto empiiriseen osioon kerättiin puolistrukturoiduilla teemahaastatteluilla. Tutkimus osoitti, että laajennettu transaktiokustannusteoria soveltuu hyvinyrityksen rajojen määrittelyyn. Staattinen transaktiokustannusteorian selitysaste ei ole riittävä, joten dynaaminen laajennus on tarpeellinen. Tutkimuksessa ilmeni, että paperiteollisuudella verrattuna muihin toimialoihin on suurimmat haasteet tehokkaiden rajojen määrittämisessä.

Russia's food retail sector from the point of view of Finnish food producers

This research paper focuses on the Russian food retail sector and its structure and development. At the momentit is one of the fastest growing markets today with 12.1% growth last year (2004). The growth originates from high oil price, which has been accumulated to people's wages. They are growing nominally more than 20% annually. But even though the income increases, the share of food of all retailtrade has been fairly stable with only a slight decline. Thus, the consumption is shifting to products with more quality and value. The shareof modern retail outlets is low, as the Russian retail sector is still very dispersed to traditional retail outlets such as kiosks, open markets and small grocery stores. The store chains are, however, becoming more and more significant. The biggest market for retailers is Moscow but nowadays the chains are expanding rapidly into other regions. Even though the markets have not been saturated in Moscow, the best prospects for growth are in the regions. The most important factor restricting the growth in Moscowis the availability of real estate and land plots for stores. The market is moving forward to saturation, and a consolidation process will follow. In fact, it has already started but not many acquisitions have been made so far. To this point the domestic chains have settled to form only alliances. The foreign players will be very strong in the tightening competition in the future. The problem of domestic chains is that the stores are nonstandardized, which is not cost-efficient. The chains are trying to enhance their power in price negotiations by forming purchasing alliances, introducing private label goods and using the regional expansion as a striking weapon. In order to follow the growing chains to other regions the producer must sell its products to the chains at favorable terms. Suppliers are strong in negotiations when they have a functioning distribution network, ability to JIT deliveries, proper documentationpolicies, a strong brand, reliability in deliveries and a fair price. The size of the entry ticket, i.e. the listing fee may define the shelf space a producer gets in the stores.

Freezing Point Depressions of Dilute Solutions of Alkali Metal Chlorides and Bromides

Freezing point depressions (¿Tf) of dilute solutions of several alkali metal chlorides and bromides were calculated by means of the best activity coefficient equations. In the calculations, Hückel, Hamer and Pitzer equationswere used for activity coefficients. The experimental ¿Tf values available in the literature for dilute LiCl, NaCl and KBr solutions can be predicted within experimental error by the Hückel equations used. The experimental ¿Tf values for dilute LiCl and KBr solutions can also be accurately calculated by corresponding Pitzer equations and those for dilute NaCl solutions by the Hamer equation for this salt. Neither Hamer nor Pitzer equations predict accurately the freezing points reported in the literature for LiBr and NaBr solutions. The ¿Tf values available for dilute solutions of RbCl, CsCl or CsBr are not known at the moment accurately because the existing data for these solutions are not precise. The freezing point depressions are tabulated in the present study for LiCl, NaCl and KBr solutions at several rounded molalities. The ¿Tf values in this table can be highly recommended. The activity coefficient equations used in the calculation of these values have been tested with almost allhigh-precision electrochemical data measured at 298.15 K.

Development of filter media treatments for liquid filtration

Woven monofilament, multifilament, and spun yarn filter media have long been the standard media in liquid filtration equipment. While the energy for a solid-liquid separation process is determined by the engineering work, it is the interface between the slurry and the equipment - the filter media - that greatly affects the performance characteristics of the unit operation. Those skilled in the art are well aware that a poorly designed filter medium may endanger the whole operation, whereas well-performing filter media can make the operation smooth and economical. As the mineral and pulp producers seek to produce ever finer and more refined fractions of their products, it is becoming increasingly important to be able to dewater slurries with average particle sizes around 1 ¿m using conventional, high-capacity filtration equipment. Furthermore, the surface properties of the media must not allow sticky and adhesive particles to adhere to the media. The aim of this thesis was to test how the dirt-repellency, electrical resistance and highpressure filtration performance of selected woven filter media can be improved by modifying the fabric or yarn with coating, chemical treatment and calendering. The results achieved by chemical surface treatments clearly show that the woven media surface properties can be modified to achieve lower electrical resistance and improved dirt-repellency. The main challenge with the chemical treatments is the abrasion resistance and, while the experimental results indicate that the treatment is sufficiently permanent to resist standard weathering conditions, they may still prove to be inadequately strong in terms of actual use.From the pressure filtration studies in this work, it seems obvious that the conventional woven multifilament fabrics still perform surprisingly well against the coated media in terms of filtrate clarity and cake build-up. Especially in cases where the feed slurry concentration was low and the pressures moderate, the conventional media seemed to outperform the coated media. In the cases where thefeed slurry concentration was high, the tightly woven media performed well against the monofilament reference fabrics, but seemed to do worse than some of the coated media. This result is somewhat surprising in that the high initial specific resistance of the coated media would suggest that the media will blind more easily than the plain woven media. The results indicate, however, that it is actually the woven media that gradually clogs during the coarse of filtration. In conclusion, it seems obvious that there is a pressure limit above which the woven media looses its capacity to keep the solid particles from penetrating the structure. This finding suggests that for extreme pressures the only foreseeable solution is the coated fabrics supported by a strong enough woven fabric to hold thestructure together. Having said that, the high pressure filtration process seems to follow somewhat different laws than the more conventional processes. Based on the results, it may well be that the role of the cloth is most of all to support the cake, and the main performance-determining factor is a long life time. Measuring the pore size distribution with a commercially available porometer gives a fairly accurate picture of the pore size distribution of a fabric, but failsto give insight into which of the pore sizes is the most important in determining the flow through the fabric. Historically air, and sometimes water, permeability measures have been the standard in evaluating media filtration performance including particle retention. Permeability, however, is a function of a multitudeof variables and does not directly allow the estimation of the effective pore size. In this study a new method for estimating the effective pore size and open pore area in a densely woven multifilament fabric was developed. The method combines a simplified equation of the electrical resistance of fabric with the Hagen-Poiseuille flow equation to estimate the effective pore size of a fabric and the total open area of pores. The results are validated by comparison to the measured values of the largest pore size (Bubble point) and the average pore size. The results show good correlation with measured values. However, the measured and estimated values tend to diverge in high weft density fabrics. This phenomenon is thought to be a result of a more tortuous flow path of denser fabrics, and could most probably be cured by using another value for the tortuosity factor.

Direct-on-line axial flux permanent magnet synchronous generator static and dynamic performance

In distributed energy production, permanent magnet synchronous generators (PMSG) are often connected to the grid via frequency converters, such as voltage source line converters. The price of the converter may constitute a large part of the costs of a generating set. Some of the permanent magnet synchronous generators with converters and traditional separately excited synchronous generators couldbe replaced by direct-on-line (DOL) non-controlled PMSGs. Small directly networkconnected generators are likely to have large markets in the area of distributed electric energy generation. Typical prime movers could be windmills, watermills and internal combustion engines. DOL PMSGs could also be applied in island networks, such as ships and oil platforms. Also various back-up power generating systems could be carried out with DOL PMSGs. The benefits would be a lower priceof the generating set and the robustness and easy use of the system. The performance of DOL PMSGs is analyzed. The electricity distribution companies have regulations that constrain the design of the generators being connected to the grid. The general guidelines and recommendations are applied in the analysis. By analyzing the results produced by the simulation model for the permanent magnet machine, the guidelines for efficient damper winding parameters for DOL PMSGs are presented. The simulation model is used to simulate grid connections and load transients. The damper winding parameters are calculated by the finite element method (FEM) and determined from experimental measurements. Three-dimensional finite element analysis (3D FEA) is carried out. The results from the simulation model and 3D FEA are compared with practical measurements from two prototype axial flux permanent magnet generators provided with damper windings. The dimensioning of the damper winding parameters is case specific. The damper winding should be dimensioned based on the moment of inertia of the generating set. It is shown that the damper winding has optimal values to reach synchronous operation in the shortest period of time after transient operation. With optimal dimensioning, interferenceon the grid is minimized.