Two-phase flow measurements with spacer grid in a rod bundle geometry

Heat transfer effectiveness in nuclear rod bundles is of great importance to nuclear reactor safety and economics. An important design parameter is the Critical Heat Flux (CHF), which limits the transferred heat from the fuel to the coolant. The CHF is determined by flow behaviour, especially the turbulence created inside the fuel rod bundle. Adiabatic experiments can be used to characterize the flow behaviour separately from the heat transfer phenomena in diabatic flow. To enhance the turbulence, mixing vanes are attached to spacer grids, which hold the rods in place. The vanes either make the flow swirl around a single sub-channel or induce cross-mixing between adjacent sub-channels. In adiabatic two-phase conditions an important phenomenon that can be investigated is the effect of the spacer on canceling the lift force, which collects the small bubbles to the rod surfaces leading to decreased CHF in diabatic conditions and thus limits the reactor power. Computational Fluid Dynamics (CFD) can be used to simulate the flow numerically and to test how different spacer configurations affect the flow. Experimental data is needed to validate and verify the used CFD models. Especially the modeling of turbulence is challenging even for single-phase flow inside the complex sub-channel geometry. In two-phase flow other factors such as bubble dynamics further complicate the modeling. To investigate the spacer grid effect on two-phase flow, and to provide further experimental data for CFD validation, a series of experiments was run on an adiabatic sub-channel flow loop using a duct-type spacer grid with different configurations. Utilizing the wire-mesh sensor technology, the facility gives high resolution experimental data in both time and space. The experimental results indicate that the duct-type spacer grid is less effective in canceling the lift force effect than the egg-crate type spacer tested earlier.

Development of a PC Tool for Estimating Pressure Drops in Forced-convection Boiler Tubes

Kaksifaasivirtauksen kuvaamiseen käytettävät mallit, ja menetelmät kaksifaasivirtauksen painehäviön määrittämiseksi kehittyvät yhä monimutkaisimmiksi. Höyrystinputkissa tapahtuvien painehäviöiden arvioinnin vaatiman laskennan suorittamiseksi tietokoneohjelman kehittäminen on välttämätöntä. Tässä työssä on kehitetty itsenäinen PC-ohjelma painehäviöiden arvioimiseksi pakotetulle konvektiovirtaukselle pystysuorissa höyrykattilan höyrystinputkissa. Veden ja vesihöyryn aineominaisuuksien laskentaan käytetään IAPWS-IF97 –yhtälökokoelmaa sekä muita tarvittavia IAPWS:n suosittelemia yhtälöitä. Höyrystinputkessa kulloinkin vallitsevan virtausmuodon määrittämiseen käytetään sovelluskelpoisia virtausmuotojen välisiä rajoja kuvaavia yhtälöitä. Ohjelmassa käytetään painehäviön määritykseen kirjallisuudessa julkaistuja yhtälöitä, virtausmuodosta riippuen, alijäähtyneelle virtaukselle, kupla-, tulppa- ja rengasvirtaukselle sekä tulistetun höyryn virtaukselle. Ohjelman laskemia painehäviöarvioita verrattiin kirjallisuudesta valittuihin mittaustuloksiin. Laskettujen painehäviöiden virhe vaihteli välillä –19.5 ja +23.9 %. Virheiden itseisarvojen keskiarvo oli 12.8 %.

Description and implementation of cut calculation-method in a sawmill

Työn tavoitteena oli kuvata ja ottaa käyttöön sahauseräkohtaisen kannattavuuden laskentamenetelmä sahalle, sekä tehdä laskentamalli menetelmän tueksi. Sahauksen peruskäsitteiden jälkeen työssä on esitelty sahan tuotantoprosessi. Tuotantoprosessi on kuvattu kirjallisuuden ja asiantuntijoiden haastattelujen perusteella. Seuraavaksi kartoitettiin hyötyjä ja vaikutuksia, mitä laskentamenetelmältä odotetaan.. Kustannuslaskennan teoriaa selvitettiin kirjallisuuslähteitä käyttäen silmälläpitäen juuri tätä kehitettävää laskentamenetelmää. Lisäksi esiteltiin Uimaharjun sahalla käytettävät ja laskentaan liittyvät laskenta- ja tietojärjestelmät.Nykyisin sahalla ei ole minkäänlaista menetelmää sahauseräkohtaisen tuloksen laskemiseksi. Pienillä muutoksilla sahan tietojärjestelmään ja prosessikoneisiin voidaan sahauserä kuljettaa prosessin läpi niin, että jokaisessa prosessin vaiheessa sille saadaan kohdistettua tuotantotietoa. Eri vaiheista saatua tietoa käyttämällä saadaan tarkasti määritettyä tuotteet, joita sahauserä tuotti ja paljonko tuotantoresursseja tuottamiseen kului. Laskentamalliin syötetään tuotantotietoja ja kustannustietoa ja saadaan vastaukseksi sahauserän taloudellinen tulos.Toimenpide ehdotuksena esitetään lisätutkimusta tuotantotietojen automaattisesta keräämisestä manuaalisen työn ja virheiden poistamiseksi. Suhteellisen pienillä panoksilla voidaan jokaiselle sahauserälle kerätä tuotantotiedot täysin automaattisesti. Lisäksi kehittämäni laskentamallin tilalle tulisi hankkia sovellus, joka käyttäisi paremmin hyväksi nykyisiä tietojärjestelmiä ja poistaisi manuaalisen työvaiheen laskennassa.

Electronic Data Interchange in Logistics Processes

Tämän diplomityön tarkoituksena oli tehdä selvitys EDI:in liittyvistä vaikutuksista, tarpeista ja eduista sekä valmistella Oracle Applications- toiminnanohjausjärjestelmän EDI Gateway- modulin ottamista tuotantokäyttöön. Tietoa tarvekartoitukseen saatiin keskustelujen avulla. Uusia kaupallisista lähtökohdista johdettuja, yritysten väliseen kaupankäyntiin ja internet-teknologian hyödyntämiseen kehitettyjä aloitteita käsiteltiin EDI-näkökulmasta tulevaisuutta varten. Ajankohtaisinta tietoa tätä diplomityötä varten löydettiin myös internetistä. Tämän jälkeen oli mahdollista toteuttaa sopivan laaja mutta rajattu EDI pilottiprojekti EDI-konseptin luomista varten. EDI:n vaikutuksiin ostossa keskityttiin tässä diplomityössä enemmän ja EDI:ä päätettiin soveltaa aluksi ostotilauksissa. EDI:n hyötyjä on vaikea mitata numeerisesti. Suurta määrää rahaa tai tuoteyksiköitä on käsiteltävä EDI-partnerin kanssa riittävän usein. EDI:n käyttöönottovaiheessa pääongelmat ovat sovelluksiin liittyviä tietotekniikkaongelmia. Selvityksistä ja EDI-projektista saatu tieto on mahdollista hyödyntää jatkokehityksessä. Lisätoimenpiteitä tarvitaan kokonaan toimivan järjestelmän luomiseksi.

Improvements in the Assessment of Bacterial Viability and Killing

It is axiomatic that our planet is extensively inhabited by diverse micro-organisms such as bacteria, yet the absolute diversity of different bacterial species is widely held to be unknown. Different bacteria can be found from the depths of the oceans to the top of the mountains; even the air is more or less colonized by bacteria. Most bacteria are either harmless or even advantageous to human beings but there are also bacteria, which can cause severe infectious diseases or spoil the supplies intended for human consumption. Therefore, it is vitally important not only to be able to detect and enumerate bacteria but also to assess their viability and possible harmfulness. Whilst the growth of bacteria is remarkably fast under optimum conditions and easy to detect by cultural methods, most bacteria are believed to lie in stationary phase of growth in which the actual growth is ceased and thus bacteria may simply be undetectable by cultural techniques. Additionally, several injurious factors such as low and high temperature or deficiency of nutrients can turn bacteria into a viable but non-culturable state (VBNC) that cannot be detected by cultural methods. Thereby, various noncultural techniques developed for the assessment of bacterial viability and killing have widely been exploited in modern microbiology. However, only a few methods are suitable for kinetic measurements, which enable the real-time detection of bacterial growth and viability. The present study describes alternative methods for measuring bacterial viability and killing as well as detecting the effects of various antimicrobial agents on bacteria on a real-time basis. The suitability of bacterial (lux) and beetle (luc) luciferases as well as green fluorescent protein (GFP) to act as a marker of bacterial viability and cell growth was tested. In particular, a multiparameter microplate assay based on GFP-luciferase combination as well as a flow cytometric measurement based on GFP-PI combination were developed to perform divergent viability analyses. The results obtained suggest that the antimicrobial activities of various drugs against bacteria could be successfully measured using both of these methods. Specifically, the data reliability of flow cytometric viability analysis was notably improved as GFP was utilized in the assay. A fluoro-luminometric microplate assay enabled kinetic measurements, which significantly improved and accelerated the assessment of bacterial viability compared to more conventional viability assays such as plate counting. Moreover, the multiparameter assay made simultaneous detection of GFP fluorescence and luciferase bioluminescence possible and provided extensive information about multiple cellular parameters in single assay, thereby increasing the accuracy of the assessment of the kinetics of antimicrobial activities on target bacteria.

Calculations of Boiling Two-Phase Flow Using a Porous Media Model

Boiling two-phase flow and the equations governing the motion of fluid in two-phase flows are discussed in this thesis. Disposition of the governing equations in three-dimensional complex geometries is considered from the perspective of the porous medium concept. The equations governing motion in two-phase flows were formulated, discretized and implemented in a subroutine for pressure-velocity solution utilizing the SIMPLE algorithm modified for two-phase flow. The subroutine was included in PORFLO, which is a three-dimensional 5-equation porous media model developed at VTT by Jaakko Miettinen. The development of two-phase flow and the resulting void fraction distribution was predicted in a geometry resembling a section of BWR fuel bundle in a couple of test cases using PORFLO.

Role of references in international industrial marketing : a theory-building case study about supplier’s processes of utilizing references

Scientific studies regarding specifically references do not seem to exist. However, the utilization of references is an important practice for many companies involved in industrial marketing. The purpose of the study is to increase the understanding about the utilization of references in international industrial marketing in order to contribute to the development of a theory of reference behavior. Specifically, the modes of reference usage in industry, the factors affecting a supplier's reference behavior, and the question how references are actually utilized, are explored in the study. Due to the explorative nature of the study, a research design was followed where theory and empirical studies alternated. An Exploratory Framework was developed to guide a pilot case study that resulted in Framework 1. Results of the pilot study guided an expanded literature review that was used to develop first a Structural Framework and a Process Framework which were combined in Framework 2. Then, the second empirical phase of the case study was conducted in the same (pilot) case company. In this phase, Decision Systems Analysis (DSA) was used as the analysis method. The DSA procedure consists of three interviewing waves: initial interviews, reinterviews, and validating interviews. Four reference decision processes were identified, described and analyzed in the form of flowchart descriptions. The flowchart descriptions were used to explore new constructs and to develop new propositions to develop Framework 2 further. The quality of the study was ascertained by many actions in both empirical parts of the study. The construct validity of the study was ascertained by using multiple sources of evidence and by asking the key informant to review the pilot case report. The DSA method itself includes procedures assuring validity. Because of the choice to conduct a single case study, external validity was not even pursued. High reliability was pursued through detailed documentation and thorough reporting of evidence. It was concluded that the core of the concept of reference is a customer relationship regardless of the concrete forms a reference might take in its utilization. Depending on various contingencies, references might have various tasks inside the four roles of increasing 1) efficiency of sales and sales management, 2) efficiency of the business, 3) effectiveness of marketing activities, and 4) effectiveness in establishing, maintaining and enhancing customer relationships. Thus, references have not only external but internal tasks as well. A supplier's reference behavior might be affected by many hierarchical conditions. Additionally, the empirical study showed that the supplier can utilize its references as a continuous, all pervasive decision making process through various practices. The process includes both individual and unstructured decision making subprocesses. The proposed concept of reference can be used to guide a reference policy recommendable for companies for which the utilization of references is important. The significance of the study is threefold: proposing the concept of reference, developing a framework of a supplier's reference behavior and its short term process of utilizing references, and conceptual structuring of an unstructured and in industrial marketing important phenomenon to four roles.

Impact of unsymmetrical loads in distribution networks

Since it is virtually impossible to balance loads in three-phase system, unbalance in a varying degree exists almost in all distribution networks. The aim of the thesis is to analyze the impact of this unbalance subject to different configurations of distribution system and winding connection of the supplying transformer. Also impact of the voltage unbalance on the equipment is investigated. In order to make the investigation more visual, the following calculations have been conducted: - Unsymmetrical load in four-wire star connected network - Unsymmetrical load in four-wire star connected network with broken zero conductor (or three-wire network). - Unsymmetrical load when the supplying transformer is so-called zigzag transformer. PDF created

First-Line Chemotherapy with Anthracycline and Taxane Combination in Metastatic Breast Cancer. Detection of bone metastases with TRACP 5b

Background: In Finland, breast cancer (BC) is the most common cancer among women, and prostate cancer (PC) that among men. At the metastatic stage both cancers remain essentially incurable. The goals of therapy include palliation of symptoms, improvement or maintenance of quality of life (QoL), delay of disease progression, and prolongation of survival. Balancing between efficacy and toxicity is the major challenge. With increasing costs of new treatments, appropriate use of resources is paramount. When new treatment regimes are introduced into clinical practice a comprehensive assessment of clinical benefit, adverse effects and cost is necessary. Both BC and PC show a predilection to metastasize to bone. Bone metastases cause significant morbidity impairing the patients´ QoL. Diagnosis of bone metastases relies mainly on radiological methods, which however lack optimal sensitivity and specificity. New tools are needed for detection and follow-up of bone metastases. Aims: Anthracyclines and taxanes are effective chemotherapeutic agents in the treatment of metastatic breast cancer (MBC) with different mechanisms of action. Therefore, evaluation of the combination of anthracyclines with taxanes was a justifiable approach in the treatment of MBC patients. We assessed the efficacy, toxicity, cost of treatment and QoL of BC patients treated with first-line chemotherapy for metastatic disease with the combination epirubicin and docetaxel. We also evaluated the diagnostic potential of tartrate-resistant acid phosphatase 5b (TRACP 5b) and carboxyterminal telopeptides of type I collagen (ICTP) in the diagnosis of bone metastases in BC and TRACP 5b in PC patients. Results: The combination of epirubicin and docetaxel was effective in this phase II study, but required individual dose adjustment to avoid neutropenic infections, and the use of growth factors to maintain a feasible dose level. The response rate was 54 % (95 % CI 37-71) and the median overall survival (OS) was 26 months. Of the patients, 87 % were treated for infections. The treatment of adverse events required additional use of health resources mainly due to neutropenic infections, thereby raising direct treatment costs by 20 %. Despite adverse events, the global QoL was not significantly compromised during the treatment. Clinically evident acute cardiac toxicity was not observed. The combination of serum TRACP 5b and ICTP was at least equally sensitive and specific in detection of of bone metastases as commonly used total alkaline phosphatise (tALP) in BC patients. In contrast, TRACP 5b was less specific and sensitive than tALP as a marker of skeletal changes in PC patients. Conclusions: Treatment with epirubicin and docetaxel showed high efficacy in first-line chemotherapy of MBC. The relatively high incidence of neutropenic infections requiring hospitalization increased the treatment costs. Despite adverse events, the global QoL of the patients was not significantly compromised. The combination of TRACP 5b and ICTP showed similar activity as tALP in detecting bone metastases in MBC. In contrast, TRACP 5b was less specific and sensitive than tALP as a marker of skeletal changes in PC.

Strategic Change Management Readiness Evaluation in Organizations

The objective of this study and paper was to find out how the strategic change management readiness in organizations can be evaluated. Based on theory and prior CMP model, the framework of strategic change management and issues related to it was constructed. Additionally a synthesis of the most important phases and interventions in strategic change process and project was created. These phases were starting point, planning, implementation and evaluation and securing phases. Qualitative approach was utilized in the empirical part of the study due to the need for in-depth information about the topics surveyed through semi-structured interview. There were 18 responders from the top management of large Finnish companies. In this study interventions, strengths and weaknesses during the various phases of strategic change projects were revealed. Additionally the interviewees’ opinion on the importance of each of the interventions in strategic change project success was asked. According to this study, the most important phases recognized through researching theoretical literature, prior CMP model and empirical information in starting point phase were analysis of current and desired state and need for change accompanied with guiding coalition formulation. In planning phase the most important interventions were project organization formulation, action plan creation, analysis of prior and current strategic change projects and organizational structure analysis. In the change project implementation phase the interventions of importance were launch, quick wins, sense of urgency creation, change resistance management and change communications. In the final evaluation and securing phase project evaluation was the most important intervention. Based on the results a tool for creating change management readiness profile was created.

Customer knowledge processing in maintenance business: case study

The purpose of the study is to examine and increase knowledge on customer knowledge processing in B2B context from sales perspective. Further objectives include identifying possible inhibiting and enabling factors in each phase of the process. The theoretical framework is based on customer knowledge management literature. The study is a qualitative study, in which the research method utilized is a case study. The empirical part was implemented in a case company by conducting in-depth interviews with the company’s value-selling champions located internationally. Context was maintenance business. Altogether 17 interviews were conducted. The empirical findings indicate that customer knowledge processing has not been clearly defined within the maintenance business line. Main inhibiting factors in acquiring customer knowledge are lack of time and vast amount of customer knowledge received. Enabling factors recognized are good customer relationships and sales representatives’ communication skills. Internal dissemination of knowledge is mainly inhibited by lack of time and restrictions in customer relationship management systems. Enabling factors are composition of the sales team and updated customer knowledge. Inhibiting utilization is lack of goals to utilize the customer knowledge and a low quality of the knowledge. Moreover, customer knowledge is not systematically updated nor analysed. Management of customer knowledge is based on the CRM system. As implications of the study, it is suggested for the case company to define customer knowledge processing in order to support maintenance business process.

Inviting the Audience – Interactive, Participatory, and Social Television in Finland

The television and the ways it has invited the audience to take part have been changing during the last decade. Today’s interaction, or rather participation, comes from multiplatform formats, such as TV spectacles that combine TV and web platforms in order to create a wider TV experience. Multiplatform phenomena have spread television consumption and traditional coffee table discussions to several different devices and environments. Television has become a part of the bigger puzzle of interconnected devices that operates on several platforms instead of just one. This thesis examines the Finnish television (2004–2014) through the notion of audience participation and introduces the technical, thematic, and social linkages as three different phases, interactive, participatory, social, and their most characteristic features in terms of audience participation. The aim of the study is also to focus on the idea of a possible change by addressing the possible and subtler variations that have taken place through the concept of digital television. Firstly, Finnish television history has gone through numerous trials, exploring the interactive potential of television formats. Finnish SMS-based iTV had its golden era around 2005, when nearly 50% of the television formats were to some extent interactive. Nowadays, interactive television formats have vanished due to their negative reputation and this important part of recent history is mainly been neglected in the academic scope. The dissertation focuses also on the present situation and the ways television content invites the audience to take part. “TV meets the Internet” is a global expression that characterises digital TV, and the use of the Web combined with television content is also examined. Also the linkages between television and social media are identified. Since television can nowadays be described multifaceted, the research approaches are also versatile. The research is based on qualitative content analysis, media observation, and Internet inquiry. The research material also varies. It consists of primary data: taped iTV formats, website material, and social media traces both from Twitter and Facebook and secondary data: discussion forums, observations from the media and Internet inquiry data. To sum up the results, the iTV phase represented, through its content, a new possibility for audiences to take part in a TV show (through gameful and textual features) in real-time. In participatory phase, the most characteristic features from TV-related content view, is the fact that online platform(s) were used to immerse the audience with additional material and, due to this, to extend the TV watching enjoyment beyond the actual broadcast. During the Social (media) phase, both of these features, real-timeness, and extended enjoyment through additional material, are combined and Facebook & Twitter, for example, are used to immerse people in live events (in real-time) via broadcast-related tweets and extra-material offered on a Facebook page. This thesis fills in the gap in Finnish television research by examining the rapid changes taken place on the field within the last ten years. The main results is that the development of Finnish digital television has been much more diverse and subtle than has been anticipated by following only the news, media, and contemporary discourses on the subject of television. The results will benefit both practitioners and academics by identifying the recent history of Finnish television.

Analysis of Phase Separator Design Criteria Using Computational Fluid Dynamics

Gravitational phase separation is a common unit operation found in most large-scale chemical processes. The need for phase separation can arise e.g. from product purification or protection of downstream equipment. In gravitational phase separation, the phases separate without the application of an external force. This is achieved in vessels where the flow velocity is lowered substantially compared to pipe flow. If the velocity is low enough, the denser phase settles towards the bottom of the vessel while the lighter phase rises. To find optimal configurations for gravitational phase separator vessels, several different geometrical and internal design features were evaluated based on simulations using OpenFOAM computational fluid dynamics (CFD) software. The studied features included inlet distributors, vessel dimensions, demister configurations and gas phase outlet configurations. Simulations were conducted as single phase steady state calculations. For comparison, additional simulations were performed as dynamic single and two-phase calculations. The steady state single phase calculations provided indications on preferred configurations for most above mentioned features. The results of the dynamic simulations supported the utilization of the computationally faster steady state model as a practical engineering tool. However, the two-phase model provides more truthful results especially with flows where a single phase does not determine the flow characteristics.

Clinical Learning Environment and Supervision. Development and Validation of the CLES Evaluation Scale

The purpose of the study is: (1) to describe how nursing students' experienced their clinical learning environment and the supervision given by staff nurses working in hospital settings; and (2) to develop and test an evaluation scale of Clinical Learning Environment and Supervision (CLES). The study has been carried out in different phases. The pilot study (n=163) explored the association between the characteristics of a ward and its evaluation as a learning environment by students. The second version of research instrument (which was developed by the results of this pilot study) were tested by an expert panel (n=9 nurse teachers) and test-retest group formed by student nurses (n=38). After this evaluative phase, the CLES was formed as the basic research instrument for this study and it was tested with the Finnish main sample (n=416). In this phase, a concurrent validity instrument (Dunn & Burnett 1995) was used to confirm the validation process of CLES. The international comparative study was made by comparing the Finnish main sample with a British sample (n=142). The international comparative study was necessary for two reasons. In the instrument developing process, there is a need to test the new instrument in some other nursing culture. Other reason for comparative international study is the reflecting the impact of open employment markets in the European Union (EU) on the need to evaluate and to integrate EU health care educational systems. The results showed that the individualised supervision system is the most used supervision model and the supervisory relationship with personal mentor is the most meaningful single element of supervision evaluated by nursing students. The ward atmosphere and the management style of ward manager are the most important environmental factors of the clinical ward. The study integrates two theoretical elements - learning environment and supervision - in developing a preliminary theoretical model. The comparative international study showed that, Finnish students were more satisfied and evaluated their clinical placements and supervision with higher scores than students in the United Kingdom (UK). The difference between groups was statistical highly significant (p= 0.000). In the UK, clinical placements were longer but students met their nurse teachers less frequently than students in Finland. Arrangements for supervision were similar. This research process has produced the evaluation scale (CLES), which can be used in research and quality assessments of clinical learning environment and supervision in Finland and in the UK. CLES consists of 27 items and it is sub-divided into five sub-dimensions. Cronbach's alpha coefficient varied from high 0.94 to marginal 0.73. CLES is a compact evaluation scale and user-friendliness makes it suitable for continuing evaluation.

Patient-perceived health-related quality of life during recovery after total hip arthroplasty – a 6-month follow-up study

Potilaiden käsitys terveyteen liittyvästä elämänlaadusta lonkan tekonivelleikkauksen jälkeisenä toipumisaikana – kuuden kuukauden seurantatutkimus Tässä kaksivaiheisessa seurantatutkimuksessa tarkasteltiin potilaiden käsitystä terveyteen liittyvästä elämänlaadusta lonkan tekonivelleikkauksen jälkeisenä toipumisaikana. Tutkimuksen ensimmäisessä vaiheessa tarkoituksena oli sekä kuvailla potilaiden kokemuksia potilaana olosta, saamastaan hoidosta ja terveyspalveluorganisaatiosta että analysoida aikaisempien tutkimusten perusteella leikkauksen tuloksia potilaan kannalta. Toisessa vaiheessa tarkoituksena oli arvioida potilaiden kokemaa elämänlaatua leikkauksen jälkeen, ja sitä vaikuttivatko primaaritulokset (fyysinen toimintakyky, kipu, ahdistus) tai taloudelliset seuraukset (potilaiden itsensämaksamat kustannukset, palvelujen käyttö) terveyteen liittyvään elämänlaatuun. Tutkimuksen tavoitteena oli löytää mahdolliset kriittiset ajankohdat tai tekijät, jotka saattavat hidastaa toipumista ja siten huonontaa potilaiden elämänlaatua. Tätä tietoa voidaan käyttää hoitotyössä kun suunnitellaan sopivaa hoitoa ja tukea toipumisajalle. Tutkimuksen ensimmäisessä vaiheessa primaarileikkaukseen tulevat potilaat (n = 17) kuvailivat teemahaastatteluissa kokemuksiaan kahdesti leikkauksen jälkeen. Haastatteluaineisto analysoitiin induktiivisella sisällönanalyysilla. Lisäksi 17 tutkimusartikkelista analysoitiin deduktiivisella sisällönanalyysilla leikkauksen tuloksia potilaalle, tuloksiin vaikuttavia tekijöitä ja käytetyt tutkimusmetodit. Toisessa vaiheessa primaari- tai revisioleikkaukseen tulevat potilaat (n = 100) arvioivat leikkauksen tuloksia kuuden kuukauden ajan leikkauksen jälkeen: terveyteen liittyvää elämänlaatua, primaarituloksia ja taloudellisia seurauksia. Aineisto kerättiin erilaisilla mittareilla: Sickness Impact Profile, Finnish Version, Stait-Trait Anxiety Inventory, ja Numeric Rating Scale. Lisäksi käytettiin tätä tutkimusta varten tehtyjä kyselylomakkeita: Fyysinen toimintakyky-mittari, Palvelujen käyttö-mittari ja Kustannusmittari. Tutkimuksen toiseen vaiheen tulokset analysoitiin tilastollisilla menetelmillä. Potilaiden terveyteen liittyvä elämänlaatu parani ja kipu lievittyi leikkauksen jälkeen ja fyysinen toimintakyky lisääntyi toipumisaikana. Positiivisista muutoksista huolimatta potilaat kokivat ahdistusta samassa määrin kuin ennen leikkaustakin. Palvelujen käyttö vaihteli toipumisajan kuluessa ja potilaiden maksamissa kustannuksissa oli suuria vaihteluita. Fyysisen toimintakyvyn lisääntyminen ja kivun lieveneminen paransivat terveyteen liittyvää elämänlaatua. Sen sijaan huonompi elämänlaatu toipumisaikana oli yhteydessä suurempaan palvelujen käyttöön, kun taas kustannuksilla ei ollut yhteyttä elämänlaatuun. Potilaiden ominaispiirteet tulisi ottaa enemmän huomioon suunniteltaessa sopivaa leikkauksenjälkeistä hoitoa ja tukea. Potilaat tarvitsevat yksilöllisiä ohjeita, sillä monet taustatekijät (esim. ikä, sukupuoli, preoperatiivinen kipu, siviilisääty, ja leikkaustyyppi) vaikuttavat toipumiseen.