Converter-flux-based current control of voltage source PWM rectifiers - analysis and implementation

Pulsewidth-modulated (PWM) rectifier technology is increasingly used in industrial applications like variable-speed motor drives, since it offers several desired features such as sinusoidal input currents, controllable power factor, bidirectional power flow and high quality DC output voltage. To achieve these features,however, an effective control system with fast and accurate current and DC voltage responses is required. From various control strategies proposed to meet these control objectives, in most cases the commonly known principle of the synchronous-frame current vector control along with some space-vector PWM scheme have been applied. Recently, however, new control approaches analogous to the well-established direct torque control (DTC) method for electrical machines have also emerged to implement a high-performance PWM rectifier. In this thesis the concepts of classical synchronous-frame current control and DTC-based PWM rectifier control are combined and a new converter-flux-based current control (CFCC) scheme is introduced. To achieve sufficient dynamic performance and to ensure a stable operation, the proposed control system is thoroughly analysed and simple rules for the controller design are suggested. Special attention is paid to the estimationof the converter flux, which is the key element of converter-flux-based control. Discrete-time implementation is also discussed. Line-voltage-sensorless reactive reactive power control methods for the L- and LCL-type line filters are presented. For the L-filter an open-loop control law for the d-axis current referenceis proposed. In the case of the LCL-filter the combined open-loop control and feedback control is proposed. The influence of the erroneous filter parameter estimates on the accuracy of the developed control schemes is also discussed. A newzero vector selection rule for suppressing the zero-sequence current in parallel-connected PWM rectifiers is proposed. With this method a truly standalone and independent control of the converter units is allowed and traditional transformer isolation and synchronised-control-based solutions are avoided. The implementation requires only one additional current sensor. The proposed schemes are evaluated by the simulations and laboratory experiments. A satisfactory performance and good agreement between the theory and practice are demonstrated.

Analyzing change in medication use - statistical approaches

The objective of this study was to gain an understanding of the effects of population heterogeneity, missing data, and causal relationships on parameter estimates from statistical models when analyzing change in medication use. From a public health perspective, two timely topics were addressed: the use and effects of statins in populations in primary prevention of cardiovascular disease and polypharmacy in older population. Growth mixture models were applied to characterize the accumulation of cardiovascular and diabetes medications among apparently healthy population of statin initiators. The causal effect of statin adherence on the incidence of acute cardiovascular events was estimated using marginal structural models in comparison with discrete-time hazards models. The impact of missing data on the growth estimates of evolution of polypharmacy was examined comparing statistical models under different assumptions for missing data mechanism. The data came from Finnish administrative registers and from the population-based Geriatric Multidisciplinary Strategy for the Good Care of the Elderly study conducted in Kuopio, Finland, during 2004–07. Five distinct patterns of accumulating medications emerged among the population of apparently healthy statin initiators during two years after statin initiation. Proper accounting for time-varying dependencies between adherence to statins and confounders using marginal structural models produced comparable estimation results with those from a discrete-time hazards model. Missing data mechanism was shown to be a key component when estimating the evolution of polypharmacy among older persons. In conclusion, population heterogeneity, missing data and causal relationships are important aspects in longitudinal studies that associate with the study question and should be critically assessed when performing statistical analyses. Analyses should be supplemented with sensitivity analyses towards model assumptions.

Monte Carlo Methods in Parameter Estimation of Nonlinear Models

Yksi keskeisimmistä tehtävistä matemaattisten mallien tilastollisessa analyysissä on mallien tuntemattomien parametrien estimointi. Tässä diplomityössä ollaan kiinnostuneita tuntemattomien parametrien jakaumista ja niiden muodostamiseen sopivista numeerisista menetelmistä, etenkin tapauksissa, joissa malli on epälineaarinen parametrien suhteen. Erilaisten numeeristen menetelmien osalta pääpaino on Markovin ketju Monte Carlo -menetelmissä (MCMC). Nämä laskentaintensiiviset menetelmät ovat viime aikoina kasvattaneet suosiotaan lähinnä kasvaneen laskentatehon vuoksi. Sekä Markovin ketjujen että Monte Carlo -simuloinnin teoriaa on esitelty työssä siinä määrin, että menetelmien toimivuus saadaan perusteltua. Viime aikoina kehitetyistä menetelmistä tarkastellaan etenkin adaptiivisia MCMC menetelmiä. Työn lähestymistapa on käytännönläheinen ja erilaisia MCMC -menetelmien toteutukseen liittyviä asioita korostetaan. Työn empiirisessä osuudessa tarkastellaan viiden esimerkkimallin tuntemattomien parametrien jakaumaa käyttäen hyväksi teoriaosassa esitettyjä menetelmiä. Mallit kuvaavat kemiallisia reaktioita ja kuvataan tavallisina differentiaaliyhtälöryhminä. Mallit on kerätty kemisteiltä Lappeenrannan teknillisestä yliopistosta ja Åbo Akademista, Turusta.

Estimates of genetic parameters of trotting performance traits for repeated annual records

Selostus: Ravihevosten jalostettavia ominaisuuksia kuvaavien kilpailumittojen perinnölliset tunnusluvut

Progeny Trial Estimates of Genetic Parameters for Growth and Quality Traits in Scots Pine

Summary

Empirical errors of small area estimates from the multisource National Forest Inventory in Eastern Finland

Abstract

Direct torque control of permanent magnet synchronous machines - analysis and implementation

Thedirect torque control (DTC) has become an accepted vector control method besidethe current vector control. The DTC was first applied to asynchronous machines,and has later been applied also to synchronous machines. This thesis analyses the application of the DTC to permanent magnet synchronous machines (PMSM). In order to take the full advantage of the DTC, the PMSM has to be properly dimensioned. Therefore the effect of the motor parameters is analysed taking the control principle into account. Based on the analysis, a parameter selection procedure is presented. The analysis and the selection procedure utilize nonlinear optimization methods. The key element of a direct torque controlled drive is the estimation of the stator flux linkage. Different estimation methods - a combination of current and voltage models and improved integration methods - are analysed. The effect of an incorrect measured rotor angle in the current model is analysed andan error detection and compensation method is presented. The dynamic performance of an earlier presented sensorless flux estimation method is made better by improving the dynamic performance of the low-pass filter used and by adapting the correction of the flux linkage to torque changes. A method for the estimation ofthe initial angle of the rotor is presented. The method is based on measuring the inductance of the machine in several directions and fitting the measurements into a model. The model is nonlinear with respect to the rotor angle and therefore a nonlinear least squares optimization method is needed in the procedure. A commonly used current vector control scheme is the minimum current control. In the DTC the stator flux linkage reference is usually kept constant. Achieving the minimum current requires the control of the reference. An on-line method to perform the minimization of the current by controlling the stator flux linkage reference is presented. Also, the control of the reference above the base speed is considered. A new estimation flux linkage is introduced for the estimation of the parameters of the machine model. In order to utilize the flux linkage estimates in off-line parameter estimation, the integration methods are improved. An adaptive correction is used in the same way as in the estimation of the controller stator flux linkage. The presented parameter estimation methods are then used in aself-commissioning scheme. The proposed methods are tested with a laboratory drive, which consists of a commercial inverter hardware with a modified software and several prototype PMSMs.

Automated, adaptive methods for forest inventory

Forest inventories are used to estimate forest characteristics and the condition of forest for many different applications: operational tree logging for forest industry, forest health state estimation, carbon balance estimation, land-cover and land use analysis in order to avoid forest degradation etc. Recent inventory methods are strongly based on remote sensing data combined with field sample measurements, which are used to define estimates covering the whole area of interest. Remote sensing data from satellites, aerial photographs or aerial laser scannings are used, depending on the scale of inventory. To be applicable in operational use, forest inventory methods need to be easily adjusted to local conditions of the study area at hand. All the data handling and parameter tuning should be objective and automated as much as possible. The methods also need to be robust when applied to different forest types. Since there generally are no extensive direct physical models connecting the remote sensing data from different sources to the forest parameters that are estimated, mathematical estimation models are of "black-box" type, connecting the independent auxiliary data to dependent response data with linear or nonlinear arbitrary models. To avoid redundant complexity and over-fitting of the model, which is based on up to hundreds of possibly collinear variables extracted from the auxiliary data, variable selection is needed. To connect the auxiliary data to the inventory parameters that are estimated, field work must be performed. In larger study areas with dense forests, field work is expensive, and should therefore be minimized. To get cost-efficient inventories, field work could partly be replaced with information from formerly measured sites, databases. The work in this thesis is devoted to the development of automated, adaptive computation methods for aerial forest inventory. The mathematical model parameter definition steps are automated, and the cost-efficiency is improved by setting up a procedure that utilizes databases in the estimation of new area characteristics.

Hakkuutähteestä valmistetun pyrolyysiöljyn elinkaaren kasvihuonekaasupäästöt

Kasvihuonekaasupäästöjen vähentämiseksi ja uusiutuvan energian käytön lisäämiseksi EU:ssa on säädetty direktiivi uusiutuvan energian käytön edistämisestä(RES-direktiivi). Direktiivissä annetaan ohjeet biopolttoaineiden ja bionesteiden kasvihuonekaasuvaikutusten laskemiseen. Tämän työn tarkoituksena oli selvittää, täyttääkö hakkuutähteistä valmistettu pyrolyysiöljy RES-direktiivin asettamat määrälliset vaatimukset kasvihuonekaasujen päästövähennykselle silloin, kun pyrolyysiöljyllä korvataan raskasta polttoöljyä lämmöntuotannossa. Laskenta suorittiin direktiivin ohjeiden mukaan. Lisäksi työssä pohdittiin laskentamenetelmän soveltuvuutta pyrolyysiöljyn ilmastovaikutusten arviointiin yleisesti. Laskennassa huomioitiin raaka-aineen tuotannosta, jalostuksesta sekä kuljetuksesta ja jakelusta aiheutuvat kasvihuonekaasupäästöt. Päästöt laskettiin ensin oletusarvoilla, jonka jälkeen suoritettiin todennäköisyyspohjainen herkkyystarkastelu valituille parametreille. Herkkyystarkastelun tuloksista huomattiin, että päästövähennys riippuu pääasiassa kahdesta tekijästä: maaperän hiilitaseen muutoksesta aiheutuvista päästöistä ja pyrolyysiprosessin tarvitseman lämmön tuotantoon käytetyistä polttoaineista. Eniten tuloksiin vaikutti kuitenkin se, oletettiinko pyrolysaattori ja kattila tarkastelussa erillisiksi yksiköiksi (tapaus 1) vai kokonaisuudeksi (tapaus 2). Tulosten perusteella näyttää siltä, että pyrolyysiöljyn käyttö lämmöntuotannossa raskaan polttoöljyn sijasta johtaa päästövähennyksiin. Saatuja tuloksia ei kuitenkaan voida pitää ennusteina pyrolyysiöljyn todellisista ilmastovaikutuksista, koska elinkaariarviointiin liittyy monia epävarmuuksia. RES-direktiivin laskentaohjeet esimerkiksi järjestelmärajausten muodostamisesta ja päästöjen kohdentamisesta ovat epätarkat. Tästä syystä direktiiviä on mahdollista tulkita usealla eri tavalla, jolloin toisistaan poikkeavat tulokset voivat silti olla kaikki direktiivin mukaisesti laskettuja. Jotta liika tulkinnanvaraisuus ei aiheuttaisi ongelmia, olisi RES-direktiivin laskentaohjetta hyvä tarkentaa.