Equilibrium moisture content of flax/linseed and fibre hemp straw fractions

Selostus: Pellavan ja kuituhampun korren jakeiden tasapainokosteus

Non-wood massojen vedenpoiston arvioiminen märkäpuristuksessa

Yksivuotisten kasvien (non-wood) kuitua verrataan usein lehtipuukuituihin. Käytetyimpiä non-wood kasveja ovat vehnän olki, bambu, järviruoko ja bagassi. Non-wood massan erottaa puumassasta kuitenkin korkea silikaattipitoisuus sekä parenkyymisolupitoisuus, joka antaa massalle korkean hienoainepitoisuuden. Tämä yhdessä korkean hemiselluloosapitoisuuden ja lyhyen kuidun pituuden kanssa heikentävät voimakkaasti non-wood massan vedenpoisto-ominaisuuksia. Non-wood kuidulla voidaan korvata lehtipuumassaa hienopapereissa. Non-wood kuitu antaa paperille hyvän opasiteetin, korkean valonsirontakertoimen sekä sileän painopinnan. Massaan lisättävä pitkäkuituinen havupuumassa parantaa ajetta¬vuutta paperikoneella ja helpottaa massan vedenpoistoa. Non-wood massan vedenpoistoa voidaan tehostaa esimerkiksi poistamalla osa hienoaineesta, käyttämällä non-wood massalle sopivaa keittotapaa sekä käyttämällä märkä¬puristuksessa pitkänippityyppistä puristinratkaisua. Myös non-wood kuidun kuivaaminen parantaa vedenpoistoa. Tässä tutkimuksessa kirjallisuusosassa keskityttiin yleisimpiin paperin valmistuksessa käytettäviin non-wood kuidun lähteisiin, märkäpuristuksen teoriaan ja tapoihin tehostaa vedenpoistoa. Kokeellisessa osassa tutkittiin vehnänolkimassan käyttäytymistä märkäpuristuksessa erilaisten ominaisuuksien pohjalta. Tutkimuksen kohteena oli non-wood massan keittotapa (hapan/alkali), hienoainepitoisuus, silikaattipitoisuus sekä kuivattu/kuivaamaton kuitu. Vertailun vuoksi tutkimuksessa oli mukana myös yksi järviruokomassa. Tuloksista huomataan, että non-wood massan vedenpoistoon vaikuttaa hienoainepitoisuus, kuidun kuivaus sekä massan valmistustapa. Järviruokomassan veden¬poisto on tehokkaampaa kuin vehnänolkimassan paremman kuitu¬koostumuksensa takia. Jos hienopaperimassassa korvataan lehtipuumassaa non-wood kuidulla maksimissaan 40 %, massan vedenpoistoa voidaan hyvin arvioida erilaisten suotautuvuusmittojen, kuten freeneksen, vedenpidätyskyvyn ja suotautumisajan, avulla.

Fouling tendency in biomass-fired boilers

Although it is well known that firing biomass fuels leads to increased deposition buildup on heat transfer surfaces in boiler compared with firing coal, existing empirical knowledge about combustion of different types of biofuels is limited. The aim of this study is to give greater awareness and understanding of the circumstances which are able to decrease considerably deposition build up on heat transfer surfaces when firing different types of biofuels. The crucial part of this thesis is experimental investigation of fouling tendency while firing biomass fuels, such as straw, bark, and peat having different chemical composition. In order to give comprehensive overview of ash deposition phenomena the number of not less important issues such as mechanisms of ash deposition, effect of fouling on heat transfer, and design of boilers subjected to ash buildup were examined as well. The answers obtained in this study may be a step towards a better knowledge of firing biofuels as separately as in mixtures, and may provide solutions for successful combustion technique of biomass fuels.

Optimised Utilization of Bioenergy in Poland

The aim of the study was to ford out the availability of biomasses, which are available for energy production, in Poland. Biomasses which were examined were forest residues and surplus straw. Availability was examined by 16 Polish voivodeships, which are provinces in Poland. After fording out the amounts of biomasses for energy production was examined the need of biomass in the biggest CHP plants in Poland. It was expected that all the plants uses 15 % of biomass as the fuel. In the first parts of the report are explained the legislation which effects to biomass use in energy production in EU level and in Polish level. Also the combustion methods best for biomasses are explained by examples. After this, is studied the general situation of renewable energy use in Poland and the facts about the country. In the last parts it's explained the calculations and is shown the example cases. When it was found out the needs and supply of biomass it was examined by examples how it could be transported to the plants from the producers. Also was examined costs effected, if there were logistical terminals between the producer and the end user. The estimation was done by setting prices for the biomass, and fording out average costs for producing and transporting biomass. There are a lot of surplus biomasses in Poland which could be used for energy production, and this is a one way to reach the goals that EU has set of renewable energies. But because biomasses doesn't have such a good calorific value, it isn't worth able to transport it very long distances. In the research was set the prices for producer 9€/MWh and for end user 15€/MWh, the maximum transportation distance for forest residues was 52 km and for straw 56 km. These are example estimations and it has to be remembered that there are a lot of factors that makes inaccurate. The model is really sensitive and by changing one parameter the results change a lot.

Utilization of retention chemicals in non-wood containing furnishes

The usage of the non-wood pulps in furnishes for various paper grades is the real alternative for substitution of wood fibres in the papermaking. This is especially important now, when the prices for wood are increasing and forest resources are depleting in many regions of our planet. However, there are several problems associated with utilization of such pulps. In terms of the papermaking process one of the main problems is the poor dewatering of the non-wood pulps. This problem can be partially solved by means of retention aids. In the literature part were described technological features of the non-wood pulps as the raw materials for paper production. Moreover, overviews of the retention chemicals and methods for retention measurement were done; special attention was paid to the mechanisms of retention and drainage. Finally, factors affecting on the drainage and retention of non-wood pulps were considered holistically. Particular emphasis was put on the possibility of enzyme treatment for drainage improvement. It was stated that retention aids can significantly improve dewatering of non-wood pulps. In the experimental part the goal was to investigate influence of various microparticle retention aids on the drainage, retention and formation of furnish containing wheat straw pulp, obtained by novel pulping process (Formico™Fib). The parallel test were performed with reference furnish containing only wood pulps. It was found that Bentonite-CPAM retention aid can significantly improve drainage and retention; however formation seems be suffer from such additives. It was stated that performance of the Silica-Starch retention aid significantly depends on the starch dosing sequence and wet-end conditions; this system have shown better formation than other tested retention aids. Silica-CPAM retention aid have provided comparable results in retention and drainage with Bentonite-CPAM, while Silica-starch did not improve dewatering and yielded in lowest filler retention among other aids. Ultimately, optimal dosages for the tested retention chemicals have been suggested.

Utilization of non-wood pulp in different fibers products

The correct utilization of non-wood raw material allows reducing tree cutting and reduces emissions of carbon dioxide from burning of non-wood plants on farmers fields. Also it allows increasing economical situation in regions that non-wood plants are grown and where they are converted into pulp and paper. Also it gives positive effect on population pressure of work by addition of working place. In the literature survey included an overview of the historical meaning of non-wood pulp on developing paper production and structure of non-wood pulps. Moreover, anatomical and chemical composition of straw, reed and bamboo were studied more detailed. Also, an overview of the utilization of non-wood pulp in papermaking was made. Especially tissue, tree-free and release papers were reviewed. In the experimental part the goal was to investigate suitability of non-wood pulp like wheat straw pulp and bamboo pulp for different fiber products. Finally release and tree-free paper products were selected for experimental studies. It was discovered that wheat straw, especially screened wheat straw, showed good results for release paper. Also utilization of wheat straw and bamboo pulp in tree-free paper showed good results and suitability of these non-wood pulps for tree-free paper production. Also it was noticed that addition of wheat straw pulp gave positive effect on initial wet strength for release and tree-free paper.

Biokaasun tuottaminen ja hyödyntäminen Lappeenrannassa

Lappeenrannassa kerätään ja hyödynnetään tällä hetkellä kaatopaikkakaasua 0,3 milj.m3 vuodessa. Biokaasua voitaisiin tuottaa Lappeenrannassa mädättämällä bioperäisiä jätteitä ja biokaasuntuotantoa varten kasvatettuja energiakasveja. Biokaasuntuotantoon soveltuvia jätteitä ovat erilliskerätty biojäte, jätevedenpuhdistamon jätevesiliete, puutarhajäte, lietelannat ja oljet. Kesannolla olevilla peltoaloilla voitaisiin kasvattaa ruokohelpeä. Biokaasun tuotantoon soveltuvia materiaaleja voitaisiin kerätä 143 000 t/a ja kasvattaa 68 000 t/a. Työssä tarkastellaan vaihtoehtoa, jossa mädätetään vain puhdistamoliete, sekä useita materiaaleja mädättävää yhteismädättämöä, johon liittyen tutkitaan kolmea eri vaihtoehtoa: kunnallisen jätteen mädätystä, kaiken jätteen mädätystä ja jätteen sekä energiakasvien mädätystä. Paras sijoituspaikka mädättämölle olisi jätevedenpuhdistamon läheisyydessä. Jätemateriaalista saataisiin kaasua enintään 12 milj. m3 ja energiakasveista enintään 16 milj. m3. Kaasusta voitaisiin tuottaa energiaa CHP-laitoksessa enintään 184 GWh. Mikäli biokaasun tuotannolla halutaan ensisijaisesti vähentää kasvi-huonekaasupäästöjä, kannattaa kaasu jalostaa ajoneuvopolttoaineeksi. Jalostettu kaasu on mahdollista myös syöttää maakaasuverkostoon. Suurimmat tulot on mahdollista saavuttaa yhdistetyssä sähkön- ja lämmöntuotannossa, mikäli biokaasulle suunniteltu syöttötariffi toteutuu. Muussa tapauksessa suurimmat tulot saadaan jalostamalla biokaasua ajoneuvojen polttoaineeksi.

Biogas production in regional integrated biodegradable waste treatment – Possibilities for improving energy performance and reducing GHG emissions

The greatest threat that the biodegradable waste causes on the environment is the methane produced in landfills by the decomposition of this waste. The Landfill Directive (1999/31/EC) aims to reduce the landfilling of biodegradable waste. In Finland, 31% of biodegradable municipal waste ended up into landfills in 2012. The pressure of reducing disposing into landfills is greatly increased by the forthcoming landfill ban on biodegradable waste in Finland. There is a need to discuss the need for increasing the utilization of biodegradable waste in regional renewable energy production to utilize the waste in a way that allows the best possibilities to reduce GHG emissions. The objectives of the thesis are: (1) to find important factors affecting renewable energy recovery possibilities from biodegradable waste, (2) to determine the main factors affecting the GHG balance of biogas production system and how to improve it and (3) to find ways to define energy performance of biogas production systems and what affects it. According to the thesis, the most important factors affecting the regional renewable energy possibilities from biodegradable waste are: the amount of available feedstock, properties of feedstock, selected utilization technologies, demand of energy and material products and the economic situation of utilizing the feedstocks. The biogas production by anaerobic digestion was seen as the main technology for utilizing biodegradable waste in agriculturally dense areas. The main reason for this is that manure was seen as the main feedstock, and it can be best utilized with anaerobic digestion, which can produce renewable energy while maintaining the spreading of nutrients on arable land. Biogas plants should be located close to the heat demand that would be enough to receive the produced heat also in the summer months and located close to the agricultural area where the digestate could be utilized. Another option for biogas use is to upgrade it to biomethane, which would require a location close to the natural gas grid. The most attractive masses for biogas production are municipal and industrial biodegradable waste because of gate fees the plant receives from them can provide over 80% of the income. On the other hand, directing gate fee masses for small-scale biogas plants could make dispersed biogas production more economical. In addition, the combustion of dry agricultural waste such as straw would provide a greater energy amount than utilizing them by anaerobic digestion. The complete energy performance assessment of biogas production system requires the use of more than one system boundary. These can then be used in calculating output–input ratios of biogas production, biogas plant, biogas utilization and biogas production system, which can be used to analyze different parts of the biogas production chain. At the moment, it is difficult to compare different biogas plants since there is a wide variation of definitions for energy performance of biogas production. A more consistent way of analyzing energy performance would allow comparing biogas plants with each other and other recovery systems and finding possible locations for further improvement. Both from the GHG emission balance and energy performance point of view, the energy consumption at the biogas plant was the most significant factor. Renewable energy use to fulfil the parasitic energy demand at the plant would be the most efficient way to reduce the GHG emissions at the plant. The GHG emission reductions could be increased by upgrading biogas to biomethane and displacing natural gas or petrol use in cars when compared to biogas CHP production. The emission reductions from displacing mineral fertilizers with digestate were seen less significant, and the greater N2O emissions from spreading digestate might surpass the emission reductions from displacing mineral fertilizers.

Persistent organic pollutants in sediments and fish from Lake Victoria, Uganda

This thesis describes the occurrence and sources of selected persistent organic pollutants (POPs) such as polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs), polychlorinated biphenyls (PCBs), polybrominated diphenyl ethers (PBDEs) and hexachlorocyclohexanes (HCHs) in the northern watershed of Lake Victoria. Sediments and fish were collected from three highly polluted embayments (i.e. Murchison Bay, Napoleon Gulf and Thurston Bay) of the lake. The analysis for PCDD/Fs, PCBs and PBDEs was done using a high resolution mass spectrometer coupled to a gas chromatograph (GC), and a GC equipped with an electron capture detector was used for HCHs. Total (Σ) PCDD/Fs, PCBs and PBDEs in sediments ranged from 3.19 to 478, 313 to 4325 and 60.8 to 179 pg g-1 dry weight (dw), respectively. The highest concentrations of pollutants were found at sites close to industrial areas and wastewater discharge points. The maximum concentrations of PCDD/Fs, PCBs, PBDEs and HCHs in fish muscle homogenates were 49, 779, 495 and 45,900 pg g-1 wet weight (ww), respectively. The concentrations of the pollutants in Nile perch (Lates niloticus) were significantly greater than those in Nile tilapia (Oreochromis niloticus), possibly due to differences in trophic level and dietary feeding habits among fish species. World Health Organization-toxic equivalency quotient (WHO2005-TEQ) values in the sediments were up to 4.24 pg g-1 dw for PCDD/Fs and 0.55 pg TEQ g-1 dw for the 12 dioxin-like PCBs (dl-PCBs). 23.1% of the samples from the Napoleon Gulf were above the interim sediment quality guideline value of 0.85 pg WHO-TEQ g-1 dw set by the Canadian Council for Ministers of the Environment. The WHO2005-TEQs in fish were 0.001-0.16 pg g-1 for PCDD/Fs and 0.001-0.31 pg g-1 ww for dl- PCBs. The TEQ values were within a permissible level of 3.5 pg g−1 ww recommended by the European Commission. Based on the Commission set TEQs and minimum risk level criteria formulated by the Agency for Toxic Substances and Disease Registry, the consumption of fish from Lake Victoria gives no indication of health risks associated to PCDD/Fs and PCBs. Principal component analysis (PCA) indicated that anthropogenic activities such as agricultural straw open burning, medical waste incinerators and municipal solid waste combustors were the major sources of PCDD/Fs in the watershed of Lake Victoria. The ratios of α-/γ-HCH varied from 0.89 to 1.68 suggesting that the highest HCH residues mainly came from earlier usage and fresh γ-HCH (lindane). In the present study, the concentration of POPs in fish were not significantly related to those in sediments, and the biota sediment accumulation factor (BSAF) concept was found to be a poor predictor of the bioavailability and bioaccumulation of environmental pollutants.

Avaintekstejä kulttuurihistoriaan

Avaintekstejä kulttuurihistoriaan avaa kulttuurihistorian tutkijoiden oivallusten syntyä esikuvallisten tekstien äärellä. Kirja esittelee lukijalle, miten empiirisesti painottuneesta tutkimuskirjallisuudesta löytää metodologisen sisällön. Tekijät kysyvät, miten tietyissä teoksissa teoria ja empiria kietoutuvat toisiinsa tavalla, joka on innoittanut kulttuurihistorian tutkijoita. Keskeinen kysymys ei siis ole, mitä kulttuurihistoria on vaan miten kulttuurihistoria on. Kirjassa esitellään sekä klassisia että varsin tuoreitakin tekstejä Jacob Burckhardtista David Nyeen, Max Weberistä Paddy Scannelliin. Kansien välissä tapaamme niin keskeisiä ja tunnettuja kulttuurihistorioitsijoita, kuten esimerkiksi Natalie Zemon Davisin ja Robert Darntonin, kuin myös Virginia Woolfin, Martin Heideggerin ja Thomas Kuhnin kulttuurihistoriallisesti luettuina. Teos keskustelee periodien ja temaattisten rajojen ylitse, sillä kulttuurihistoriassa renessanssiajan Englantiin sijoittuva tutkimusaihe voi kertoa 1800-luvun tutkijalle enemmän kuin arvaisikaan, ja populaarikulttuurilla voi olla paljonkin tekemistä sukupuolijärjestelmän tai tilaproblematiikan kanssa.

Chemical changes in biomass during torrefaction

Torrefaction is moderate thermal treatment (~200-300 °C) of biomass in an inert atmosphere. The torrefied fuel offers advantages to traditional biomass, such as higher heating value, reduced hydrophilic nature, increased its resistance to biological decay, and improved grindability. These factors could, for instance, lead to better handling and storage of biomass and increased use of biomass in pulverized combustors. In this work, we look at several aspects of changes in the biomass during torrefaction. We investigate the fate of carboxylic groups during torrefaction and its dependency to equilibrium moisture content. The changes in the wood components including carbohydrates, lignin, extractable materials and ashforming matters are also studied. And at last, the effect of K on torrefaction is investigated and then modeled. In biomass, carboxylic sites are partially responsible for its hydrophilic characteristic. These sites are degraded to varying extents during torrefaction. In this work, methylene blue sorption and potentiometric titration were applied to measure the concentration of carboxylic groups in torrefied spruce wood. The results from both methods were applicable and the values agreed well. A decrease in the equilibrium moisture content at different humidity was also measured for the torrefied wood samples, which is in good agreement with the decrease in carboxylic group contents. Thus, both methods offer a means of directly measuring the decomposition of carboxylic groups in biomass during torrefaction as a valuable parameter in evaluating the extent of torrefaction. This provides new information to the chemical changes occurring during torrefaction. The effect of torrefaction temperature on the chemistry of birch wood was investigated. The samples were from a pilot plant at Energy research Center of the Netherlands (ECN). And in that way they were representative of industrially produced samples. Sugar analysis was applied to analyze the hemicellulose and cellulose content during torrefaction. The results show a significant degradation of hemicellulose already at 240 °C, while cellulose degradation becomes significant above 270 °C torrefaction. Several methods including Klason lignin method, solid state NMR and Py-GC-MS analyses were applied to measure the changes in lignin during torrefaction. The changes in the ratio of phenyl, guaiacyl and syringyl units show that lignin degrades already at 240 °C to a small extent. To investigate the changes in the extractives from acetone extraction during torrefaction, gravimetric method, HP-SEC and GC-FID followed by GC-MS analysis were performed. The content of acetone-extractable material increases already at 240 °C torrefaction through the degradation of carbohydrate and lignin. The molecular weight of the acetone-extractable material decreases with increasing the torrefaction temperature. The formation of some valuable materials like syringaresinol or vanillin is also observed which is important from biorefinery perspective. To investigate the change in the chemical association of ash-forming elements in birch wood during torrefaction, chemical fractionation was performed on the original and torrefied birch samples. These results give a first understanding of the changes in the association of ashforming elements during torrefaction. The most significant changes can be seen in the distribution of calcium, magnesium and manganese, with some change in water solubility seen in potassium. These changes may in part be due to the destruction of carboxylic groups. In addition to some changes in water and acid solubility of phosphorous, a clear decrease in the concentration of both chlorine and sulfur was observed. This would be a significant additional benefit for the combustion of torrefied biomass. Another objective of this work is studying the impact of organically bound K, Na, Ca and Mn on mass loss of biomass during torrefaction. These elements were of interest because they have been shown to be catalytically active in solid fuels during pyrolysis and/or gasification. The biomasses were first acid washed to remove the ash-forming matters and then organic sites were doped with K, Na, Ca or Mn. The results show that K and Na bound to organic sites can significantly increase the mass loss during torrefaction. It is also seen that Mn bound to organic sites increases the mass loss and Ca addition does not influence the mass loss rate on torrefaction. This increase in mass loss during torrefaction with alkali addition is unlike what has been found in the case of pyrolysis where alkali addition resulted in a reduced mass loss. These results are important for the future operation of torrefaction plants, which will likely be designed to handle various biomasses with significantly different contents of K. The results imply that shorter retention times are possible for high K-containing biomasses. The mass loss of spruce wood with different content of K was modeled using a two-step reaction model based on four kinetic rate constants. The results show that it is possible to model the mass loss of spruce wood doped with different levels of K using the same activation energies but different pre-exponential factors for the rate constants. Three of the pre-exponential factors increased linearly with increasing K content, while one of the preexponential factors decreased with increasing K content. Therefore, a new torrefaction model was formulated using the hemicellulose and cellulose content and K content. The new torrefaction model was validated against the mass loss during the torrefaction of aspen, miscanthus, straw and bark. There is good agreement between the model and the experimental data for the other biomasses, except bark. For bark, the mass loss of acetone extractable material is also needed to be taken into account. The new model can describe the kinetics of mass loss during torrefaction of different types of biomass. This is important for considering fuel flexibility in torrefaction plants.

Potential of energy and nutrient recovery from biodegradable waste by co-treatment in Lithuania

Biodegradable waste quantities in Lithuania and their potential for the co-treatment in renewable energy and organic fertilizer production are investigated. Two scenarios are formulated to study the differences of the amounts of obtainable energy and fertilizers between different ways of utilization. In the first scenario, only digestion is used, and in the second scenario, other materials than straw are digested, and straw and the solid fraction of sewage sludge digestate are combusted. As a result, the amounts of heat and electricity, as well as the fertilizer amounts in the counties are obtained for both scenarios. Based on this study, the share of renewable energy in Lithuania could be doubled by the co-treatment of different biodegradable materials.

Potential to decrease GHG emissions from biomass resources in China

This paper describes the environment issues which are caused by fossil fuel utilization, and the available of biomass resources and relevant applications in China and relevant policy for supporting biomass resources development. In addition the sustainable technology for energy and fuels generation in China and the advantages and disadvantages of technologies are presented as well. This paper aims to find out how the policy can promotes the biomass resource development and from environment aspect to see why the biomass resources should replace fossil fuels in the future. In this paper the life cycle assessment of straw biomass resource will be as an example to present the same amount of energy produced by straw and coal, the different amount of emission will be emitted.