Transformation of carbon dioxide to diethyl carbonate over ceria and ceria-supported catalysts

Carbon dioxide is regarded, nowadays, as a primary anthropogenic greenhouse gas leading to global warming. Hence, chemical fixation of CO2 has attracted much attention as a possible way to manufacture useful chemicals. One of the most interesting approaches of CO2 transformations is the synthesis of organic carbonates. Since conventional production technologies of these compounds involve poisonous phosgene and carbon monoxide, there is a need to develop novel synthetic methods that would better match the principles of "Green Chemistry" towards protection of the environment and human health. Over the years, synthesis of dimethyl carbonate was under intensive investigation in the academia and industry. Therefore, this study was entirely directed towards equally important homologue of carbonic esters family namely diethyl carbonate (DEC). Novel synthesis method of DEC starting from ethanol and CO2 over heterogeneous catalysts based on ceria (CeO2) was studied in the batch reactor. However, the plausible drawback of the reaction is thermodynamic limitations. The calculated values revealed that the reaction is exothermic (ΔrHØ298K = ─ 16.6 J/ ) and does not occur spontaneously at rooms temperature (ΔrGØ 298K = 35.85 kJ/mol). Moreover, co-produced water easily shifts the reaction equilibrium towards reactants excluding achievement of high yields of the carbonate. Therefore, in-situ dehydration has been applied using butylene oxide as a chemical water trap. A 9-fold enhancement in the amount of DEC was observed upon introduction of butylene oxide to the reaction media in comparison to the synthetic method without any water removal. This result confirms that reaction equilibrium was shifted in favour of the desired product and thermodynamic boundaries of the reaction were suppressed by using butylene oxide as a water scavenger. In order to obtain insight into the reaction network, the kinetic experiments were performed over commercial cerium oxide. On the basis of the selectivity/conversion profile it could be concluded that the one-pot synthesis of diethyl carbonate from ethanol, CO2 and butylene oxide occurs via a consecutive route involving cyclic carbonate as an intermediate. Since commercial cerium oxide suffers from the deactivation problems already after first reaction cycle, in-house CeO2 was prepared applying room temperature precipitation technique. Variation of the synthesis parameters such as synthesis time, calcination temperature and pH of the reaction solution turned to have considerable influence on the physico-chemical and catalytic properties of CeO2. The increase of the synthesis time resulted in high specific surface area of cerium oxide and catalyst prepared within 50 h exhibited the highest amount of basic sites on its surface. Furthermore, synthesis under pH 11 yielded cerium oxide with the highest specific surface area, 139 m2/g, among all prepared catalysts. Moreover, CeO2─pH11 catalyst demonstrated the best catalytic activity and 2 mmol of DEC was produced at 180 oC and 9 MPa of the final reaction pressure. In addition, ceria-supported onto high specific surface area silicas MCM-41, SBA-15 and silica gel were synthesized and tested for the first time as catalysts in the synthesis of DEC. Deposition of cerium oxide on MCM-41 and SiO2 supports resulted in a substantial increase of the alkalinity of the carrier materials. Hexagonal SBA-15 modified with 20 wt % of ceria exhibited the second highest basicity in the series of supported catalysts. Evaluation of the catalytic activity of ceria-supported catalysts showed that reaction carried out over 20 wt % CeO2-SBA-15 generated the highest amount of DEC.

Calcination of aluminum hydroxide over pressure and residence time

This work investigates the possible effect of pressure and residence time to the reaction of aluminum hydroxide into aluminum oxide. Various pressurized conditions are used as well as the help of various residence times. The aim is to increase the conversion of the reaction with the use of different pressures and residence times. The tests were performed with a laboratory scale fluidized bed reactor at the Outotec R&D Center in Frankfurt. Additional test work such as particle size analysis and differential thermal analysis were also carried out. Some calcined samples were also characterized with X-ray diffraction at the University of Auckland to obtain a reaction pathway when using pressurized conditions. All of the results are then compared with previous results.

The Proposed Financial Transaction Tax – Extraterritorial Effect, Tax Evasion and Other Legal Problems Facing the Proposal

The main topic of this master’s thesis is the proposed EU directive on a financial transaction tax. Ten Member States which want to enact the directive by using enhanced cooperation are currently negotiating the contents of the proposal. This tax would be levied on specific products which are traded on the financial markets. As an example the transaction of stocks would be taxed at a percentage of 0.1 percent, and the transaction of derivatives at a percentage of 0.01 percent. The proposed financial transaction tax would enter into force in said ten countries but it would still have effects on those countries, which are not planning on participating in this taxation system. This is one of the main reasons why this tax has faced a lot of opposition in several European Union countries. The main legal problems the tax is predicted to have are tax evasion, double taxation, and extraterritorial effect. The Commission has stated that it is aiming to reach certain objectives with the financial transaction tax. These objectives are for example to stabilise the financial markets following the financial crisis, and to deter tax evasion. Commission has defended the planning of the financial transaction tax by stating that the tax is likely to reach its objectives. The planning of the financial transaction tax began already in 2011 when the Commission published the first draft of the proposal. Following this the proposal was last amended in 2013, but the participating Member States are currently still negotiating the contents of the proposal. The participating Member States published a statement in December 2015 in which they promised that there will be a decision made about the financial transaction tax by the end of June 2016.

The Finnish Paper Workers' Union at a crossroads: Labor union representativeness in a changing environment, 1980-2008

This thesis consists of four articles and an introductory section. The main research questions in all the articles refer to the changes in the representativeness of the Finnish Paper Workers' Union. Representativeness stands for the entire entity of external, internal, legal and reputational factors that enable the labor union to represent its members and achieve its goals. This concept is based on an extensive reading of quantitative and qualitative industrial relations literature, which includes works based on Marxist labor-capital relations (such as Hyman's industrial relations studies), and more recent union density studies as well as gender- and ethnic diversity-based 'union revitalization' studies. Müller-Jentsch's German studies of industrial relations have been of particular importance as well as Streeck's industrial unionism and technology studies. The concept of representativeness is an attempt to combine the insights of these diverse strands of literature and bring the scientific discussion of labor unions back to the core of a union's function: representing its members. As such, it can be seen as a theoretical innovation. The concept helps to acknowledge both the heterogeneity of the membership and the totality of a labor union organization. The concept of representativeness aims to move beyond notions of 'power'. External representativeness can be expressed through the position of the labor union in the industrial relations system and the economy. Internal representativeness focuses on the aspects of labor unions that relate to the function of the union as an association with members, such as internal democracy. Legal representativeness lies in the formal legal position of the union – its rights and instruments. This includes collective bargaining legislation, co-decision rules and industrial conflict legislation. Reputational representativeness is related to how the union is seen by other actors and the general public, and can be approximated using data on strike activity. All these aspects of representativeness are path-dependent, and show the results of previous struggles over issues. The concept of representativeness goes beyond notions of labor union power and symbolizes an attempt to bring back the focus of industrial relations studies to the union's basic function of representing its members. The first article shows in detail the industrial conflict of the Finnish paper industry in 2005. The intended focus was the issue of gender in the negotiations over a new collective agreement, but the focal point of the industrial conflict was the issue of outsourcing and how this should be organized. Also, the issue of continuous shifts as an issue of working time was very important. The drawn-out conflict can be seen as a struggle over principles, and under pressure the labor union had to concede ground on the aforementioned issues. The article concludes that in this specific conflict, the union represented its' female members to a lesser extent, because the other issues took such priority. Furthermore, because of the substantive concessions. the union lost some of its internal representativeness, and the stubbornness of the union may have even harmed the reputation of the union. This article also includes an early version of the representativeness framework, through which this conflict is analyzed. The second article discusses wage developments, union density and collective bargaining within the context of representativeness. It is shown that the union has been able to secure substantial benefits for its members, regardless of declining employment. Collective agreements have often been based on centralized incomes policies, but the paper sector has not always joined these. Attention is furthermore paid to the changing competition of the General Assembly, with a surprisingly strong position of the Left Alliance still. In an attempt to replicate analysis of union density measures, an analysis of sectoral union density shows that similar factors as in aggregate data influence this measure, though – due to methodological issues – the results may not be robust. On this issue, it can be said that the method of analysis for aggregate union density is not suitable for sectoral union density analysis. The increasingly conflict-ridden industrial relations predicted have not actually materialized. The article concludes by asking whether the aim of ever-increasing wages is a sustainable one in the light of the pressures of globalization, though wage costs are a relatively small part of total costs. The third article discusses the history and use of outsourcing in the Finnish paper industry. It is shown using Hyman's framework of constituencies that over time, the perspective of the union changed from 'members of the Paper Workers' Union' to a more specific view of who is a core member of the union. Within the context of the industrial unionism that the union claims to practice, this is an important change. The article shows that the union more and more caters for a core group, while auxiliary personnel is less important to the union's identity and constituencies, which means that the union's internal representativeness has decreased. Maintenance workers are an exception; the union and employers have developed a rotating system that increases the efficient allocation of these employees. The core reason of the exceptional status of maintenance personnel is their high level of non-transferable skills. In the end it is debatable whether the compromise on outsourcing solves the challenges facing the industry. The fourth article shows diverging discourses within the union with regard to union-employer partnership for competitiveness improvements and instruments of local union representatives. In the collective agreement of 2008, the provision regulating wage effects of significant changes in the organization or content of work was thoroughly changed, though this mainly reflected decisions by the Labor Court on the pre-2008 version of the provision. This change laid bare the deep rift between the Social Democratic and Left Alliance (ex-Communist) factions of the union. The article argues that through the changed legal meaning of the provision, the union was able to transform concession bargaining into a basis for partnership. The internal discontent about this issue is nonetheless substantial and a threat to the unity of the union, both locally and at the union level. On the basis of the results of the articles, other factors influencing representativeness, such as technology and EU law and an overview of the main changes in the Finnish paper industry, it is concluded that, especially in recent years, the Finnish Paper Workers' Union has lost some of its representativeness. In particular, the loss of the efficiency of strikes is noted, the compromise on outsourcing which may have alienated a substantial part of the union's membership, and the change in the collective agreement of 2008 have caused this decline. In the latter case, the internal disunion on that issue shows the constraints of the union's internal democracy. Furthermore, the failure of the union to join the TEAM industrial union (by democratic means), the internal conflicts and a narrow focus on its own sector may also hurt the union in the future, as the paper industry in Finland is going through a structural change. None of these changes in representativeness would have been so drastic without the considerable pressure of globalization - in particular changing markets, changing technology and a loss of domestic investments to foreign investments, which in the end have benefited the corporations more than the Finnish employees of these corporations. Taken together, the union risks becoming socially irrelevant in time, though it will remain formally very strong on the basis of its institutional setting and financial situation.

Practical applications of a systematic approach to the chemical abatement of pollutants in water and air

The present dissertation is devoted to the systematic approach to the development of organic toxic and refractory pollutants abatement by chemical decomposition methods in aqueous and gaseous phases. The systematic approach outlines the basic scenario of chemical decomposition process applications with a step-by-step approximation to the most effective result with a predictable outcome for the full-scale application, confirmed by successful experience. The strategy includes the following steps: chemistry studies, reaction kinetic studies in interaction with the mass transfer processes under conditions of different control parameters, contact equipment design and studies, mathematical description of the process for its modelling and simulation, processes integration into treatment technology and its optimisation, and the treatment plant design. The main idea of the systematic approach for oxidation process introduction consists of a search for the most effective combination between the chemical reaction and the treatment device, in which the reaction is supposed to take place. Under this strategy,a knowledge of the reaction pathways, its products, stoichiometry and kinetics is fundamental and, unfortunately, often unavailable from the preliminary knowledge. Therefore, research made in chemistry on novel treatment methods, comprisesnowadays a substantial part of the efforts. Chemical decomposition methods in the aqueous phase include oxidation by ozonation, ozone-associated methods (O3/H2O2, O3/UV, O3/TiO2), Fenton reagent (H2O2/Fe2+/3+) and photocatalytic oxidation (PCO). In the gaseous phase, PCO and catalytic hydrolysis over zero valent ironsare developed. The experimental studies within the described methodology involve aqueous phase oxidation of natural organic matter (NOM) of potable water, phenolic and aromatic amino compounds, ethylene glycol and its derivatives as de-icing agents, and oxygenated motor fuel additives ¿ methyl tert-butyl ether (MTBE) ¿ in leachates and polluted groundwater. Gas-phase chemical decomposition includes PCO of volatile organic compounds and dechlorination of chlorinated methane derivatives. The results of the research summarised here are presented in fifteenattachments (publications and papers submitted for publication and under preparation).

Effect of Mechanical and Geometric Mismatching on Fatigue and Damage of Welded Joints

The future of high technology welded constructions will be characterised by higher strength materials and improved weld quality with respect to fatigue resistance. The expected implementation of high quality high strength steel welds will require that more attention be given to the issues of crack initiation and mechanical mismatching. Experiments and finite element analyses were performed within the framework of continuum damage mechanics to investigate the effect of mismatching of welded joints on void nucleation and coalescence during monotonic loading. It was found that the damage of undermatched joints mainly occurred in the sandwich layer and the damageresistance of the joints decreases with the decrease of the sandwich layer width. The damage of over-matched joints mainly occurred in the base metal adjacent to the sandwich layer and the damage resistance of the joints increases with thedecrease of the sandwich layer width. The mechanisms of the initiation of the micro voids/cracks were found to be cracking of the inclusions or the embrittled second phase, and the debonding of the inclusions from the matrix. Experimental fatigue crack growth rate testing showed that the fatigue life of under-matched central crack panel specimens is longer than that of over-matched and even-matched specimens. Further investigation by the elastic-plastic finite element analysis indicated that fatigue crack closure, which originated from the inhomogeneousyielding adjacent to the crack tip, played an important role in the fatigue crack propagation. The applicability of the J integral concept to the mismatched specimens with crack extension under cyclic loading was assessed. The concept of fatigue class used by the International Institute of Welding was introduced in the parametric numerical analysis of several welded joints. The effect of weld geometry and load condition on fatigue strength of ferrite-pearlite steel joints was systematically evaluated based on linear elastic fracture mechanics. Joint types included lap joints, angle joints and butt joints. Various combinations of the tensile and bending loads were considered during the evaluation with the emphasis focused on the existence of both root and toe cracks. For a lap joint with asmall lack-of-penetration, a reasonably large weld leg and smaller flank angle were recommended for engineering practice in order to achieve higher fatigue strength. It was found that the fatigue strength of the angle joint depended strongly on the location and orientation of the preexisting crack-like welding defects, even if the joint was welded with full penetration. It is commonly believed that the double sided butt welds can have significantly higher fatigue strength than that of a single sided welds, but fatigue crack initiation and propagation can originate from the weld root if the welding procedure results in a partial penetration. It is clearly shown that the fatigue strength of the butt joint could be improved remarkably by ensuring full penetration. Nevertheless, increasing the fatigue strength of a butt joint by increasing the size of the weld is an uneconomical alternative.

Gamma spectrometry and gamma and X-ray tomography of nuclear fuel

The purpose of gamma spectrometry and gamma and X-ray tomography of nuclear fuel is to determine both radionuclide concentration and integrity and deformation of nuclear fuel. The aims of this thesis have been to find out the basics of gamma spectrometry and tomography of nuclear fuel, to find out the operational mechanisms of gamma spectrometry and tomography equipment of nuclear fuel, and to identify problems that relate to these measurement techniques. In gamma spectrometry of nuclear fuel the gamma-ray flux emitted from unstable isotopes is measured using high-resolution gamma-ray spectroscopy. The production of unstable isotopes correlates with various physical fuel parameters. In gamma emission tomography the gamma-ray spectrum of irradiated nuclear fuel is recorded for several projections. In X-ray transmission tomography of nuclear fuel a radiation source emits a beam and the intensity, attenuated by the nuclear fuel, is registered by the detectors placed opposite. When gamma emission or X-ray transmission measurements are combined with tomographic image reconstruction methods, it is possible to create sectional images of the interior of nuclear fuel. MODHERATO is a computer code that simulates the operation of radioscopic or tomographic devices and it is used to predict and optimise the performance of imaging systems. Related to the X-ray tomography, MODHERATO simulations have been performed by the author. Gamma spectrometry and gamma and X-ray tomography are promising non-destructive examination methods for understanding fuel behaviour under normal, transient and accident conditions.

Numbers and Languages

The thesis presents results obtained during the authors PhD-studies. First systems of language equations of a simple form consisting of just two equations are proved to be computationally universal. These are systems over unary alphabet, that are seen as systems of equations over natural numbers. The systems contain only an equation X+A=B and an equation X+X+C=X+X+D, where A, B, C and D are eventually periodic constants. It is proved that for every recursive set S there exists natural numbers p and d, and eventually periodic sets A, B, C and D such that a number n is in S if and only if np+d is in the unique solution of the abovementioned system of two equations, so all recursive sets can be represented in an encoded form. It is also proved that all recursive sets cannot be represented as they are, so the encoding is really needed. Furthermore, it is proved that the family of languages generated by Boolean grammars is closed under injective gsm-mappings and inverse gsm-mappings. The arguments apply also for the families of unambiguous Boolean languages, conjunctive languages and unambiguous languages. Finally, characterizations for morphisims preserving subfamilies of context-free languages are presented. It is shown that the families of deterministic and LL context-free languages are closed under codes if and only if they are of bounded deciphering delay. These families are also closed under non-codes, if they map every letter into a submonoid generated by a single word. The family of unambiguous context-free languages is closed under all codes and under the same non-codes as the families of deterministic and LL context-free languages.

α-Pinene oxide and verbenol oxide isomerizations over heterogeneous catalysts

Terpenes are a valuable natural resource for the production of fine chemicals. Turpentine, obtained from biomass and also as a side product of softwood industry, is rich in monoterpenes such as α-pinene and β-pinene, which are widely used as raw materials in the synthesis of flavors, fragrances and pharmaceutical compounds. The rearrangement of their epoxides has been thoroughly studied in recent years, as a method to obtain compounds which are further used in the fine chemical industry. The industrially most desired products of α-pinene oxide isomerization are campholenic aldehyde and trans-carveol. Campholenic aldehyde is an intermediate for the manufacture of sandalwood-like fragrances such as santalol. Trans-carveol is an expensive constituent of the Valencia orange essence oil used in perfume bases and food flavor composition. Furthermore it has been found to exhibit chemoprevention of mammary carcinogenesis. A wide range of iron and ceria supported catalysts were prepared, characterized and tested for α-pinene oxide isomerization in order to selective synthesis of above mentioned products. The highest catalytic activity in the preparation of campholenic aldehyde over iron modified catalysts using toluene as a solvent at 70 °C (total conversion of α-pinene oxide with a selectivity of 66 % to the desired aldehyde) was achieved in the presence of Fe-MCM-41. Furthermore, Fe-MCM-41 catalyst was successfully regenerated without deterioration of catalytic activity and selectivity. The most active catalysts in the synthesis of trans-carveol from α-pinene oxide over iron and ceria modified catalysts in N,N-dimethylacetamide as a solvent at 140 °C (total conversion of α-pinene oxide with selectivity 43 % to trans-carveol) were Fe-Beta-300 and Ce-Si-MCM-41. These catalysts were further tested for an analogous reaction, namely verbenol oxide isomerization. Verbenone is another natural organic compound which can be found in a variety of plants or synthesized by allylic oxidation of α-pinene. An interesting product which is synthesized from verbenone is (1R,2R,6S)-3-methyl-6-(prop-1-en-2-yl)cyclohex-3-ene-1,2-diol. It has been discovered that this diol possesses potent anti-Parkinson activity. The most effective way leading to desired diol starts from verbenone and includes three stages: epoxidation of verbenone to verbenone oxide, reduction of verbenone oxide and subsequent isomerization of obtained verbenol oxide, which is analogous to isomerization of α-pinene oxide. In the research focused on the last step of these synthesis, high selectivity (82 %) to desired diol was achieved in the isomerization of verbenol oxide at a conversion level of 96 % in N,N-dimethylacetamide at 140 °C using iron modified zeolite, Fe-Beta-300. This reaction displayed surprisingly high selectivity, which has not been achieved yet. The possibility of the reuse of heterogeneous catalysts without activity loss was demonstrated.

Large-eddy simulation of wind flows over complex terrains for wind energy applications

Wind energy has obtained outstanding expectations due to risks of global warming and nuclear energy production plant accidents. Nowadays, wind farms are often constructed in areas of complex terrain. A potential wind farm location must have the site thoroughly surveyed and the wind climatology analyzed before installing any hardware. Therefore, modeling of Atmospheric Boundary Layer (ABL) flows over complex terrains containing, e.g. hills, forest, and lakes is of great interest in wind energy applications, as it can help in locating and optimizing the wind farms. Numerical modeling of wind flows using Computational Fluid Dynamics (CFD) has become a popular technique during the last few decades. Due to the inherent flow variability and large-scale unsteadiness typical in ABL flows in general and especially over complex terrains, the flow can be difficult to be predicted accurately enough by using the Reynolds-Averaged Navier-Stokes equations (RANS). Large- Eddy Simulation (LES) resolves the largest and thus most important turbulent eddies and models only the small-scale motions which are more universal than the large eddies and thus easier to model. Therefore, LES is expected to be more suitable for this kind of simulations although it is computationally more expensive than the RANS approach. With the fast development of computers and open-source CFD software during the recent years, the application of LES toward atmospheric flow is becoming increasingly common nowadays. The aim of the work is to simulate atmospheric flows over realistic and complex terrains by means of LES. Evaluation of potential in-land wind park locations will be the main application for these simulations. Development of the LES methodology to simulate the atmospheric flows over realistic terrains is reported in the thesis. The work also aims at validating the LES methodology at a real scale. In the thesis, LES are carried out for flow problems ranging from basic channel flows to real atmospheric flows over one of the most recent real-life complex terrain problems, the Bolund hill. All the simulations reported in the thesis are carried out using a new OpenFOAM® -based LES solver. The solver uses the 4th order time-accurate Runge-Kutta scheme and a fractional step method. Moreover, development of the LES methodology includes special attention to two boundary conditions: the upstream (inflow) and wall boundary conditions. The upstream boundary condition is generated by using the so-called recycling technique, in which the instantaneous flow properties are sampled on aplane downstream of the inlet and mapped back to the inlet at each time step. This technique develops the upstream boundary-layer flow together with the inflow turbulence without using any precursor simulation and thus within a single computational domain. The roughness of the terrain surface is modeled by implementing a new wall function into OpenFOAM® during the thesis work. Both, the recycling method and the newly implemented wall function, are validated for the channel flows at relatively high Reynolds number before applying them to the atmospheric flow applications. After validating the LES model over simple flows, the simulations are carried out for atmospheric boundary-layer flows over two types of hills: first, two-dimensional wind-tunnel hill profiles and second, the Bolund hill located in Roskilde Fjord, Denmark. For the twodimensional wind-tunnel hills, the study focuses on the overall flow behavior as a function of the hill slope. Moreover, the simulations are repeated using another wall function suitable for smooth surfaces, which already existed in OpenFOAM® , in order to study the sensitivity of the flow to the surface roughness in ABL flows. The simulated results obtained using the two wall functions are compared against the wind-tunnel measurements. It is shown that LES using the implemented wall function produces overall satisfactory results on the turbulent flow over the two-dimensional hills. The prediction of the flow separation and reattachment-length for the steeper hill is closer to the measurements than the other numerical studies reported in the past for the same hill geometry. The field measurement campaign performed over the Bolund hill provides the most recent field-experiment dataset for the mean flow and the turbulence properties. A number of research groups have simulated the wind flows over the Bolund hill. Due to the challenging features of the hill such as the almost vertical hill slope, it is considered as an ideal experimental test case for validating micro-scale CFD models for wind energy applications. In this work, the simulated results obtained for two wind directions are compared against the field measurements. It is shown that the present LES can reproduce the complex turbulent wind flow structures over a complicated terrain such as the Bolund hill. Especially, the present LES results show the best prediction of the turbulent kinetic energy with an average error of 24.1%, which is a 43% smaller than any other model results reported in the past for the Bolund case. Finally, the validated LES methodology is demonstrated to simulate the wind flow over the existing Muukko wind farm located in South-Eastern Finland. The simulation is carried out only for one wind direction and the results on the instantaneous and time-averaged wind speeds are briefly reported. The demonstration case is followed by discussions on the practical aspects of LES for the wind resource assessment over a realistic inland wind farm.