Ultrasound-assisted electrochemical treatment of wastewaters containing organic pollutants by using novel Ti/Ta2O5-SnO2 electrodes

Advanced oxidation processes (AOPs) are modern methods using reactive hydroxyl radicals for the mineralization of organic pollutants into simple inorganic compounds, such as CO2 and H2O. Among AOPs electrochemical oxidation (EO) is a method suitable for coloured and turbid wastewaters. The degradation of pollutants occurs on electrocatalytic electrodes. The majority of electrodes contain in their structure either expensive materials (diamond and Pt-group metals) or are toxic for the environment compounds (Sb or Pb). One of the main disadvantages of electrochemical method is the polarization and contamination of electrodes due to the deposition of reaction products on their surface, which results in diminishing of the process efficiency. Ultrasound combined with the electrochemical degradation process eliminates electrode contamination because of the continuous mechanical cleaning effect produced by the formation and collapse of acoustic cavitation bubbles near to the electrode surface. Moreover, high frequency ultrasound generates hydroxyl radicals at water sonolysis. Ultrasound-assisted EO is a non-selective method for oxidation of different organic compounds with high degradation efficiencies. The aim of this research was to develop novel sustainable and cost-effective electrodes working as electrocatalysts and test their activity in electrocatalytic oxidation of organic compounds such as dyes and organic acids. Moreover, the goal of the research was to enhance the efficiency of electrocatalytic degradation processes by assisting it with ultrasound in order to eliminate the main drawbacks of a single electrochemical oxidation such as electrodes polarization and passivation. Novel Ti/Ta2O5-SnO2 electrodes were developed and found to be electrocatalytically active towards water (with 5% Ta content, 10 oxide film layers) and organic compounds oxidation (with 7.5% Ta content, 8 oxide film layers) and therefore these electrodes can be applicable in both environmental and energy fields. The synergetic effect of combined electrolysis and sonication was shown while conducting sonoelectrochemical (EO/US) degradation of methylene blue (MB) and formic acid (FA). Complete degradation of MB and FA was achieved after 45 and 120 min of EO/US process respectively in neutral media. Mineralization efficiency of FA over 95% was obtained after 2 h of degradation using high frequency ultrasound (381, 863, 1176 kHz) combined with 9.1 mA/cm2 current density. EO/US degradation of MB provided over 75% mineralization in 8 h. High degradation kinetic rates and mineralization efficiencies of model pollutants obtained in EO/US experiments provide the preconditions for further extrapolation of this treatment method to pilot scale studies with industrial wastewaters.

Perussyyanalyysien käyttö ydinvoimalaitosten tapahtumien tutkinnassa

Tämä diplomityö käsittelee perussyyanalyysien käyttöä Loviisan voimalaitoksella tapahtumien tutkinnassa. Diplomityössä käydään läpi erilaisia maailmalla käytössä olevia perussyyanalyysimenetelmiä. Nykyään Loviisan voimalaitoksella ei ole ohjeessa määritelty miten perussyyanalyysit tulee tehdä, joten diplomityön tulosten perusteella on tarkoitus valita Loviisan voimalaitokselle sopiva menetelmä. Diplomityössä tehdään eräs perussyyanalyysi kahdella eri menetelmällä, jotka tuntuivat sopivilta menetelmiltä Loviisan voimalaitoksille. Perussyyanalyysimenetelmät, joita käytetään, ovat Loviisassa käytetty sovellettu HPES-menetelmä ja yhdysvaltalaisten ydinvoimaviranomaisten kehittämä HPIP-menetelmä. Perussyyanalyysien valmistuttua ja tuloksia vertaillessa tultiin siihen lopputulokseen, ettei Loviisan voimalaitoksella ole tarvetta vaihtaa nykyisin käytössä olevaa mutta ohjeistamatonta menetelmää. Loviisan voimalaitokselle tehtävään uuteen perussyyanalyysiohjeeseen liitetään menetelmäkuvaus sovelletusta HPES-menetelmästä. Menetelmäkuvauksessa kuvataan miten HPES-menetelmää käytetään perussyyanalyysien tekoon Loviisan voimalaitoksella.

Pain-evoked alterations on gingival blood flow and gingival crevicular fluid (GCF) neuropeptide SP and collagenase-2 (MMP-8) levels

Previous studies have demonstrated that clinical pulpal pain can induce the expression of pro-inflammatory neuropeptides in the adjacent gingival crevice fluid (GCF). Vasoactive agents such as substance P (SP) are known to contribute to the inflammatory type of pain and are associated with increased blood flow. More recent animal studies have shown that application of capsaicin on alveolar mucosa provokes pain and neurogenic vasodilatation in the adjacent gingiva. Pain-associated inflammatory reactions may initiate expression of several pro- and anti-inflammatory mediators. Collagenase-2 (MMP-8) has been considered to be the major destructive protease, especially in the periodontitis-affected gingival crevice fluid (GCF). MMP-8 originates mostly from neutrophil leukocytes, the first line of defence cells that exist abundantly in GCF, especially in inflammation. With this background, we wished to clarify the spatial extensions and differences between tooth-pain stimulation and capsaicin-induced neurogenic vasodilatation in human gingiva. Experiments were carried out to study whether tooth stimulation and capsaicin stimulation of alveolar mucosa would induce changes in GCF MMP-8 levels and whether tooth stimulation would release neuropeptide SP in GCF. The experiments were carried out on healthy human volunteers. During the experiments, moderate and high intensity painful tooth stimulation was performed by a constant current tooth stimulator. Moderate tooth stimulation activates A-delta fibres, while high stimulation also activates C-fibres. Painful stimulation of the gingiva was achieved by topical application of capsaicin-moistened filter paper on the mucosal surface. Capsaicin is known to activate selectively nociceptive C-fibres of stimulated tissue. Pain-evoked vasoactive changes in gingivomucosal tissues were mapped by laser Doppler imaging (LDI), which is a sophisticated and non-invasive method for studying e.g. spatial and temporal characteristics of pain- and inflammation-evoked blood flow changes in gingivomucosal tissues. Pain-evoked release of MMP-8 in GCF samples was studied by immunofluorometric assay (IFMA) and Western immunoblotting. The SP levels in GCF were analysed by Enzyme immunoassay (EIA). During the experiments, subjective stimulus-evoked pain responses were determined by a visual analogue pain scale. Unilateral stimulation of alveolar mucosa and attached gingiva by capsaicin evoked a distinct neurogenic vasodilatation in the ipsilateral gingiva, which attenuated rapidly at the midline. Capsaicin stimulation of alveolar mucosa provoked clear inflammatory reactions. In contrast to capsaicin stimuli, tooth stimulation produced symmetrical vasodilatations bilaterally in the gingiva. The ipsilateral responses were significantly smaller during tooth stimulation than during capsaicin stimuli. The current finding – that tooth stimulation evokes bilateral vasodilatation while capsaicin stimulation of the gingiva mainly produces unilateral vasodilatation – emphasises the usefulness of LDI in clarifying spatial features of neurogenic vasoactive changes in the intra-oral tissues. Capsaicin stimulation of the alveolar mucosa induced significant elevations in MMP-8 levels and activation in GCF of the adjacent teeth. During the experiments, no marked changes occurred in MMP-8 levels in the GCF of distantly located teeth. Painful stimulation of the upper incisor provoked elevations in GCF MMP-8 and SP levels of the stimulated tooth. The GCF MMP-8 and SP levels of the non-stimulated teeth were not changed. These results suggest that capsaicin-induced inflammatory reactions in gingivomucosal tissues do not cross the midline in the anterior maxilla. The enhanced reaction found during stimulation of alveolar mucosa indicates that alveolar mucosa is more sensitive to chemical irritants than the attached gingiva. Analysis of these data suggests that capsaicin-evoked neurogenic inflammation in the gingiva can trigger the expression and activation of MMP-8 in GCF of the adjacent teeth. In this study, it is concluded that experimental tooth pain at C-fibre intensity can induce local elevations in MMP-8 and SP levels in GCF. Depending on the role of MMP-8 in inflammation, in addition to surrogated tissue destruction, the elevated MMP-8 in GCF may also reflect accelerated local defensive and anti-inflammatory reactions.

Reconstruction and analysis of surface variation using photometric stereo

In many industrial applications, accurate and fast surface reconstruction is essential for quality control. Variation in surface finishing parameters, such as surface roughness, can reflect defects in a manufacturing process, non-optimal product operational efficiency, and reduced life expectancy of the product. This thesis considers reconstruction and analysis of high-frequency variation, that is roughness, on planar surfaces. Standard roughness measures in industry are calculated from surface topography. A fast and non-contact method to obtain surface topography is to apply photometric stereo in the estimation of surface gradients and to reconstruct the surface by integrating the gradient fields. Alternatively, visual methods, such as statistical measures, fractal dimension and distance transforms, can be used to characterize surface roughness directly from gray-scale images. In this thesis, the accuracy of distance transforms, statistical measures, and fractal dimension are evaluated in the estimation of surface roughness from gray-scale images and topographies. The results are contrasted to standard industry roughness measures. In distance transforms, the key idea is that distance values calculated along a highly varying surface are greater than distances calculated along a smoother surface. Statistical measures and fractal dimension are common surface roughness measures. In the experiments, skewness and variance of brightness distribution, fractal dimension, and distance transforms exhibited strong linear correlations to standard industry roughness measures. One of the key strengths of photometric stereo method is the acquisition of higher frequency variation of surfaces. In this thesis, the reconstruction of planar high-frequency varying surfaces is studied in the presence of imaging noise and blur. Two Wiener filterbased methods are proposed of which one is optimal in the sense of surface power spectral density given the spectral properties of the imaging noise and blur. Experiments show that the proposed methods preserve the inherent high-frequency variation in the reconstructed surfaces, whereas traditional reconstruction methods typically handle incorrect measurements by smoothing, which dampens the high-frequency variation.

Magneettisairaalan työnantajakuvan merkitys lääkäri- ja sairaanhoitajaopiskelijoiden näkökulmasta tarkasteltuna

Tämä tutkimus tarkastelee valmistumassa olevien lääkäri- ja sairaanhoitajaopiskelijoiden näkemyksiä terveydenhuollon työnantajakuvaan ja sen vetovoimaisuuteen liittyen. Tarkastelun näkökulmina ovat strateginen henkilöstövoimavarojen johtaminen, rekrytointiprosessi ja motivaatio työhön hakeutumisessa. Aihetta on tutkittu toistaiseksi vähän terveydenhuollon opiskelijoiden näkökulmasta. Laadullisen tutkimuksen teoreettinen osuus toteutettiin kyselylomakkeella. Kyselylomakkeen vastausten (n=14) analyysissä käytettiin sisällönanalyysiä. Tulosten mukaan voidaan todeta, että terveydenhuollon työnantajakuvalla on melko suuri merkitys lääkäreiden ja sairaanhoitajien työhön hakeutumisessa. Työpaikan vetovoimaisuutta lisäävät tekijät liittyvät esimiehen hyviin johtamistaitoihin, ammatillisen osaamisen kehittämisen mahdollisuuksiin ja kilpailukykyiseen palkkaukseen. Lisäksi työpaikan sijainnilla ja tehtävän sisällöllä on vaikutusta työpaikkaan hakeutumisessa. Vetovoimaisuutta vähentävät vastaavasti huono työilmapiiri, huono palkka, esimiehen heikot johtamistaidot sekä konsultaatiomahdollisuuksien puute. Rekrytointiprosesseissa ja työnantajan markkinoinnissa on vaihtelua eri työnantajien välillä.

Detection of the Vulnerable Atherosclerotic Plaque. Pre-Clinical Evaluation of Novel PET Imaging Probes With Experimental Models

Atherosclerosis is a life-long vascular inflammatory disease and the leading cause of death in Finland and in other western societies. The development of atherosclerotic plaques is progressive and they form when lipids begin to accumulate in the vessel wall. This accumulation triggers the migration of inflammatory cells that is a hallmark of vascular inflammation. Often, this plaque will become unstable and form vulnerable plaque which may rupture causing thrombosis and in the worst case, causing myocardial infarction or stroke. Identification of these vulnerable plaques before they rupture could save lives. At present, in the clinic, there exists no appropriated, non-invasive method for their identification. The aim of this thesis was to evaluate novel positron emission tomography (PET) probes for the detection of vulnerable atherosclerotic plaques and to characterize, two mouse models of atherosclerosis. These studies were performed by using ex vivo and in vivo imaging modalities. The vulnerability of atherosclerotic plaques was evaluated as expression of active inflammatory cells, namely macrophages. Age and the duration of high-fat diet had a drastic impact on the development of atherosclerotic plaques in mice. In imaging of atherosclerosis, 6-month-old mice, kept on high-fat diet for 4 months, showed matured, metabolically active, atherosclerotic plaques. [18F]FDG and 68Ga were accumulated in the areas representative of vulnerable plaques. However, the slow clearance of 68Ga limits its use for the plaque imaging. The novel synthesized [68Ga]DOTA-RGD and [18F]EF5 tracers demonstrated efficient uptake in plaques as compared to the healthy vessel wall, but the pharmacokinetic properties of these tracers were not optimal in used models. In conclusion, these studies resulted in the identification of new strategies for the assessment of plaque stability and mouse models of atherosclerosis which could be used for plaque imaging. In the used probe panel, [18F]FDG was the best tracer for plaque imaging. However, further studies are warranted to clarify the applicability of [18F]EF5 and [68Ga]DOTA-RGD for imaging of atherosclerosis with other experimental models.

Characterisation of Laser Beam and Paper Material Interaction

It is known already from 1970´s that laser beam is suitable for processing paper materials. In this thesis, term paper materials mean all wood-fibre based materials, like dried pulp, copy paper, newspaper, cardboard, corrugated board, tissue paper etc. Accordingly, laser processing in this thesis means all laser treatments resulting material removal, like cutting, partial cutting, marking, creasing, perforation etc. that can be used to process paper materials. Laser technology provides many advantages for processing of paper materials: non-contact method, freedom of processing geometry, reliable technology for non-stop production etc. Especially packaging industry is very promising area for laser processing applications. However, there are only few industrial laser processing applications worldwide even in beginning of 2010´s. One reason for small-scale use of lasers in paper material manufacturing is that there is a shortage of published research and scientific articles. Another problem, restraining the use of laser for processing of paper materials, is colouration of paper material i.e. the yellowish and/or greyish colour of cut edge appearing during cutting or after cutting. These are the main reasons for selecting the topic of this thesis to concern characterization of interaction of laser beam and paper materials. This study was carried out in Laboratory of Laser Processing at Lappeenranta University of Technology (Finland). Laser equipment used in this study was TRUMPF TLF 2700 carbon dioxide laser that produces a beam with wavelength of 10.6 μm with power range of 190-2500 W (laser power on work piece). Study of laser beam and paper material interaction was carried out by treating dried kraft pulp (grammage of 67 g m-2) with different laser power levels, focal plane postion settings and interaction times. Interaction between laser beam and dried kraft pulp was detected with different monitoring devices, i.e. spectrometer, pyrometer and active illumination imaging system. This way it was possible to create an input and output parameter diagram and to study the effects of input and output parameters in this thesis. When interaction phenomena are understood also process development can be carried out and even new innovations developed. Fulfilling the lack of information on interaction phenomena can assist in the way of lasers for wider use of technology in paper making and converting industry. It was concluded in this thesis that interaction of laser beam and paper material has two mechanisms that are dependent on focal plane position range. Assumed interaction mechanism B appears in range of average focal plane position of 3.4 mm and 2.4 mm and assumed interaction mechanism A in range of average focal plane position of 0.4 mm and -0.6 mm both in used experimental set up. Focal plane position 1.4 mm represents midzone of these two mechanisms. Holes during laser beam and paper material interaction are formed gradually: first small hole is formed to interaction area in the centre of laser beam cross-section and after that, as function of interaction time, hole expands, until interaction between laser beam and dried kraft pulp is ended. By the image analysis it can be seen that in beginning of laser beam and dried kraft pulp material interaction small holes off very good quality are formed. It is obvious that black colour and heat affected zone appear as function of interaction time. This reveals that there still are different interaction phases within interaction mechanisms A and B. These interaction phases appear as function of time and also as function of peak intensity of laser beam. Limit peak intensity is the value that divides interaction mechanism A and B from one-phase interaction into dual-phase interaction. So all peak intensity values under limit peak intensity belong to MAOM (interaction mechanism A one-phase mode) or to MBOM (interaction mechanism B onephase mode) and values over that belong to MADM (interaction mechanism A dual-phase mode) or to MBDM (interaction mechanism B dual-phase mode). Decomposition process of cellulose is evolution of hydrocarbons when temperature is between 380- 500°C. This means that long cellulose molecule is split into smaller volatile hydrocarbons in this temperature range. As temperature increases, decomposition process of cellulose molecule changes. In range of 700-900°C, cellulose molecule is mainly decomposed into H2 gas; this is why this range is called evolution of hydrogen. Interaction in this range starts (as in range of MAOM and MBOM), when a small good quality hole is formed. This is due to “direct evaporation” of pulp via decomposition process of evolution of hydrogen. And this can be seen can be seen in spectrometer as high intensity peak of yellow light (in range of 588-589 nm) which refers to temperature of ~1750ºC. Pyrometer does not detect this high intensity peak since it is not able to detect physical phase change from solid kraft pulp to gaseous compounds. As interaction time between laser beam and dried kraft pulp continues, hypothesis is that three auto ignition processes occurs. Auto ignition of substance is the lowest temperature in which it will spontaneously ignite in a normal atmosphere without an external source of ignition, such as a flame or spark. Three auto ignition processes appears in range of MADM and MBDM, namely: 1. temperature of auto ignition of hydrogen atom (H2) is 500ºC, 2. temperature of auto ignition of carbon monoxide molecule (CO) is 609ºC and 3. temperature of auto ignition of carbon atom (C) is 700ºC. These three auto ignition processes leads to formation of plasma plume which has strong emission of radiation in range of visible light. Formation of this plasma plume can be seen as increase of intensity in wavelength range of ~475-652 nm. Pyrometer shows maximum temperature just after this ignition. This plasma plume is assumed to scatter laser beam so that it interacts with larger area of dried kraft pulp than what is actual area of beam cross-section. This assumed scattering reduces also peak intensity. So result shows that assumably scattered light with low peak intensity is interacting with large area of hole edges and due to low peak intensity this interaction happens in low temperature. So interaction between laser beam and dried kraft pulp turns from evolution of hydrogen to evolution of hydrocarbons. This leads to black colour of hole edges.

Thermal modelling of commercial lithium-ion batteries

The accelerating adoption of electrical technologies in vehicles over the recent years has led to an increase in the research on electrochemical energy storage systems, which are among the key elements in these technologies. The application of electrochemical energy storage systems for instance in hybrid electrical vehicles (HEVs) or hybrid mobile working machines allows tolerating high power peaks, leading to an opportunity to downsize the internal combustion engine and reduce fuel consumption, and therefore, CO2 and other emissions. Further, the application of electrochemical energy storage systems provides an option of kinetic and potential energy recuperation. Presently, the lithium-ion (Li-ion) battery is considered the most suitable electrochemical energy storage type in HEVs and hybrid mobile working machines. However, the intensive operating cycle produces high heat losses in the Li-ion battery, which increase its operating temperature. The Li-ion battery operation at high temperatures accelerates the ageing of the battery, and in the worst case, may lead to a thermal runaway and fire. Therefore, an appropriate Li-ion battery cooling system should be provided for the temperature control in applications such as HEVs and mobile working machines. In this doctoral dissertation, methods are presented to set up a thermal model of a single Li-ion cell and a more complex battery module, which can be used if full information about the battery chemistry is not available. In addition, a non-destructive method is developed for the cell thermal characterization, which allows to measure the thermal parameters at different states of charge and in different points of cell surface. The proposed models and the cell thermal characterization method have been verified by experimental measurements. The minimization of high thermal non-uniformity, which was detected in the pouch cell during its operation with a high C-rate current, was analysed by applying a simplified pouch cell 3D thermal model. In the analysis, heat pipes were incorporated into the pouch cell cooling system, and an optimization algorithm was generated for the estimation of the optimalplacement of heat pipes in the pouch cell cooling system. An analysis of the application of heat pipes to the pouch cell cooling system shows that heat pipes significantly decrease the temperature non-uniformity on the cell surface, and therefore, heat pipes were recommended for the enhancement of the pouch cell cooling system.

Non-wood massojen vedenpoiston arvioiminen märkäpuristuksessa

Yksivuotisten kasvien (non-wood) kuitua verrataan usein lehtipuukuituihin. Käytetyimpiä non-wood kasveja ovat vehnän olki, bambu, järviruoko ja bagassi. Non-wood massan erottaa puumassasta kuitenkin korkea silikaattipitoisuus sekä parenkyymisolupitoisuus, joka antaa massalle korkean hienoainepitoisuuden. Tämä yhdessä korkean hemiselluloosapitoisuuden ja lyhyen kuidun pituuden kanssa heikentävät voimakkaasti non-wood massan vedenpoisto-ominaisuuksia. Non-wood kuidulla voidaan korvata lehtipuumassaa hienopapereissa. Non-wood kuitu antaa paperille hyvän opasiteetin, korkean valonsirontakertoimen sekä sileän painopinnan. Massaan lisättävä pitkäkuituinen havupuumassa parantaa ajetta¬vuutta paperikoneella ja helpottaa massan vedenpoistoa. Non-wood massan vedenpoistoa voidaan tehostaa esimerkiksi poistamalla osa hienoaineesta, käyttämällä non-wood massalle sopivaa keittotapaa sekä käyttämällä märkä¬puristuksessa pitkänippityyppistä puristinratkaisua. Myös non-wood kuidun kuivaaminen parantaa vedenpoistoa. Tässä tutkimuksessa kirjallisuusosassa keskityttiin yleisimpiin paperin valmistuksessa käytettäviin non-wood kuidun lähteisiin, märkäpuristuksen teoriaan ja tapoihin tehostaa vedenpoistoa. Kokeellisessa osassa tutkittiin vehnänolkimassan käyttäytymistä märkäpuristuksessa erilaisten ominaisuuksien pohjalta. Tutkimuksen kohteena oli non-wood massan keittotapa (hapan/alkali), hienoainepitoisuus, silikaattipitoisuus sekä kuivattu/kuivaamaton kuitu. Vertailun vuoksi tutkimuksessa oli mukana myös yksi järviruokomassa. Tuloksista huomataan, että non-wood massan vedenpoistoon vaikuttaa hienoainepitoisuus, kuidun kuivaus sekä massan valmistustapa. Järviruokomassan veden¬poisto on tehokkaampaa kuin vehnänolkimassan paremman kuitu¬koostumuksensa takia. Jos hienopaperimassassa korvataan lehtipuumassaa non-wood kuidulla maksimissaan 40 %, massan vedenpoistoa voidaan hyvin arvioida erilaisten suotautuvuusmittojen, kuten freeneksen, vedenpidätyskyvyn ja suotautumisajan, avulla.

Experimental Studies on Non-Metallic Composite Bone Implants With a Special Reference to Staphylococcal Biofilm Infection

Non-metallic implants made of bioresorbable or biostable synthetic polymers are attractive options in many surgical procedures, ranging from bioresorbable suture anchors of arthroscopic surgery to reconstructive skull implants made of biostable fiber-reinforced composites. Among other benefits, non-metallic implants produce less interference in imaging. Bioresorbable polymer implants may be true multifunctional, serving as osteoconductive scaffolds and as matrices for simultaneous delivery of bone enhancement agents. As a major advantage for loading conditions, mechanical properties of biostable fiber-reinforced composites can be matched with those of the bone. Unsolved problems of these biomaterials are related to the risk of staphylococcal biofilm infections and to the low osteoconductivity of contemporary bioresorbable composite implants. This thesis was focused on the research and development of a multifunctional implant model with enhanced osteoconductivity and low susceptibility to infection. In addition, the experimental models for assessment, diagnostics and prophylaxis of biomaterial-related infections were established. The first experiment (Study I) established an in vitro method for simultaneous evaluation of calcium phosphate and biofilm formation on bisphenol-Aglycidyldimethacrylate and triethylenglycoldimethacrylate (BisGMA-TEGDMA) thermosets with different content of bioactive glass 45S5. The second experiment (Study II) showed no significant difference in osteointegration of nanostructured and microsized polylactide-co-glycolide/β-tricalcium phosphate (PLGA /β-TCP) composites in a minipig model. The third experiment (Study III) demonstrated that positron emission tomography (PET) imaging with the novel 68Ga labelled 1,4,7,10-tetraazacyclododecane-1,4,7,10-tetraacetic acid (DOTA) CD33 related sialic-acid immunoglobulin like lectins (Siglec-9) tracer was able to detect inflammatory response to S. epidermidis and S. aureus peri-implant infections in an intraosseous polytetrafluoroethylene catheter model. In the fourth experiment (Study IV), BisGMATEGDMA thermosets coated with lactose-modified chitosan (Chitlac) and silver nanoparticles exhibited antibacterial activity against S. aureus and P. aeruginosa strains in an in vitro biofilm model and showed in vivo biocompatibility in a minipig model. In the last experiment (Study V), a selective androgen modulator (SARM) released from a poly(lactide)-co-ε-caprolactone (PLCL) polymer matrix failed to produce a dose-dependent enhancement of peri-implant osteogenesis in a bone marrow ablation model.

Content-centered method for search engine optimization

Value of online business has grown to over one trillion USD. This thesis is about search engine optimization, which focus is to increase search engine rankings. Search engine optimization is an important branch of online marketing because the first page of search engine results is generating majority of the search traffic. Current articles about search engine optimization and Google are indicating that with the proper use of quality content, there is potential to improve search engine rankings. However, the existing search engine optimization literature is not noticing content at a sufficient level. To decrease that difference, the content-centered method for search engine optimization is constructed, and content in search engine optimization is studied. This content-centered method consists of three search engine optimization tactics: 1) content, 2) keywords, and 3) links. Two propositions were used for testing these tactics in a real business environment and results are suggesting that the content-centered method is improving search engine rankings. Search engine optimization is constantly changing because Google is adjusting its search algorithm regularly. Still, some long-term trends can be recognized. Google has said that content is growing its importance as a ranking factor in the future. The content-centered method is taking advance of this new trend in search engine optimization to be relevant for years to come.

Content-centered method for search engine optimization

Value of online business has grown to over one trillion USD. This thesis is about search engine optimization, which focus is to increase search engine rankings. Search engine optimization is an important branch of online marketing because the first page of search engine results is generating majority of the search traffic. Current articles about search engine optimization and Google are indicating that with the proper use of quality content, there is potential to improve search engine rankings. However, the existing search engine optimization literature is not noticing content at a sufficient level. To decrease that difference, the content-centered method for search engine optimization is constructed, and content in search engine optimization is studied. This content-centered method consists of three search engine optimization tactics: 1) content, 2) keywords, and 3) links. Two propositions were used for testing these tactics in a real business environment and results are suggesting that the content-centered method is improving search engine rankings. Search engine optimization is constantly changing because Google is adjusting its search algorithm regularly. Still, some long-term trends can be recognized. Google has said that content is growing its importance as a ranking factor in the future. The content-centered method is taking advance of this new trend in search engine optimization to be relevant for years to come.

Confronting a victim of intimate partner violence in nursing care : a literature review

Intimate partner violence is a growing problem in health care. The purpose of this thesis was to find ways of confronting a victim of intimate partner violence in nursing care and methods how nurses can encourage the victim to disclose the abuse. The aim of this thesis was to help the health care professionals to understand the issue and the need of the victims better, and that way provide a better care. This thesis is a literature review of previously made research articles about intimate partner violence. The research material consisted of 10 published articles, which were collected from different databases. The articles were published within 10 years. A content analysis method was used to examine the articles by making descriptive summary tables according to each questions. The results of this study showed multiple factors which the health care providers should take into consideration when caring the patients. Asking with a non-judgemental attitude, in a safe, confidential setting without the partner present and prioritizing the abuse was mentioned to be important for the victims. Routinely screening and different kind of brochures was considered as good methods to encourage the victims to disclose the abuse. The need for better training and counselling of the health care providers was also discovered. The results of this thesis, did answer to the chosen study questions and that way the purpose of the thesis was filled. Hopefully, in the future this problem can be minimized and prevented in advanced. Further studies are needed to examine whether these caring methods are actually being used in clinical settings and do they have any effect.

Effective notch method assessment of misalignment for fatigue loaded welds

 The objective of this thesis work was to assess axial misalignment in fatigue loaded welds using the effective notch method. As a result, the fatigue behaviour of non-load carrying cruciform fillet welded joint under cyclic tensile loading has been studied. Various degrees of axial misalignment have been found in one series of non-load carrying cruciform fillet welded joints used in a laboratory investigation. As a result, it was important to carry out a comprehensive investigation since axial misalignment forms part of thequality of fatigue loaded structure and can reduce the fatigue strength. To extend the study, the correlation between fatigue strength and stress ratio, as well as stress concentration factor, were also studied. Moreover, a closer investigation of place of crack initiation and its dependence on weld sequence and imperfections of test specimen (angular distortion) was studied. For the fatigue class calculations, FEM (finite element method) and the effectivenotch approach are used. The addressed variable is the axial misalignment whichis introduce by modeling the entire joint. Fracture mechanics based calculations are also used and quantitatively compared with effective notch and experimental results.