The Influence of Certain Processing Factors on the Durability of Yttrium Stabilized Zirconia Used As Dental Biomaterial

In dentistry, yttrium partially stabilized zirconia (ZrO2) has become one of the most attractive ceramic materials for prosthetic applications. The aim of this series of studies was to evaluate whether certain treatments used in the manufacturing process, such as sintering time, color shading or heat treatment of zirconia affect the material properties. Another aim was to evaluate the load-bearing capacity and marginal fit of manually copy-milled custom-made versus prefabricated commercially available zirconia implant abutments. Mechanical properties such as flexural strength and surface microhardness were determined for green-stage milled and sintered yttrium partially stabilized zirconia after different sintering time, coloring process and heat treatments. Scanning electron microscope (SEM) was used for analyzing the possible changes in surface structure of zirconia material after reduced sintering time, coloring and heat treatments. Possible phase change from the tetragonal to the monoclinic phase was evaluated by X-ray diffraction analysis (XRD). The load-bearing capacity of different implant abutments was measured and the fit between abutment and implant replica was examined with SEM. The results of these studies showed that the shorter sintering time or the thermocycling did not affect the strength or surface microhardness of zirconia. Coloring of zirconia decreased strength compared to un-colored control zirconia, and some of the colored zirconia specimens also showed a decrease in surface microhardness. Coloring also affected the dimensions of zirconia. Significantly decreased shrinkage was found for colored zirconia specimens during sintering. Heat treatment of zirconia did not seem to affect materials’ mechanical properties but when a thin coating of wash and glaze porcelain was fired on the tensile side of the disc the flexural strength decreased significantly. Furthermore, it was found that thermocycling increased the monoclinic phase on the surface of the zirconia. Color shading or heat treatment did not seem to affect phase transformation but small monoclinic peaks were detected on the surface of the heat treated specimens with a thin coating of wash and glaze porcelain on the opposite side. Custom-made zirconia abutments showed comparable load-bearing capacity to the prefabricated commercially available zirconia abutments. However, the fit of the custom-made abutments was less satisfactory than that of the commercially available abutments. These studies suggest that zirconia is a durable material and other treatments than color shading used in the manufacturing process of zirconia bulk material does not affect the material’s strength. The decrease in strength and dimensional changes after color shading needs to be taken into account when fabricating zirconia substructures for fixed dental prostheses. Manually copy-milled custom-made abutments have acceptable load-bearing capacity but the marginal accuracy has to be evaluated carefully.

Catalytic transformations of fatty acid derivatives for food, oleochemicals and fuels over carbon supported platinum group metals

Växtoljor som utgör en förnybar naturresurs används som sådana eller i modifierade former i många industriella processer, som är av stor betydelse för vårt vardagliga liv. Växtoljor används i livsmedel, i kemiska och farmaceutiska produkter, i textilindustrin, för framställning av färgämnen och beläggningsmaterial samt som miljövänliga bränslekomponenter. Fetter och oljor hör till de äldsta kemiska komponenterna som utnyttjas av människan. De består huvudsakligen av glycerolestrar och fettsyror. Fetter och oljor har typiskt en kolkedja med kol-koldubbelbindningar samt karboxyl- och estergrupper, som kan genom hydrering eller dekarboxylering konverteras till nyttiga och miljövänliga produkter med hjälp av ädelmetallkatalysatorer. Aktivt kol (C) används som bärare på katalysatorerna. Väteaddition, d.v.s. hydrering av växtoljor har varit föremål för omfattande forskning i över hundra års tid. Hydreringen är en viktig process, för den tillämpas på produktion av fetter och margarin. Omättade fettsyror hydreras traditionellt på nickelbaserade heterogena katalysatorer. Samtidigt med en partiell hydrering av fettsyrorna och fettsyraestrarna som har två dubbelbindningar pågår också isomeringsreaktioner, vilka ger cis- och transisomerer av reaktantmolekylerna. Den största nackdelen med nickelkatalysatorerna är deras giftighet samt bildning av ohälsosamma transisomerer i reaktionsprodukterna. Dessutom deaktiveras nickelkatalysatorn snabbt p.g.a. att nickeltvålar bildas i reaktionsblandningen. Platinabaserade katalysatorer lider däremot inte av dessa begränsningar. Metaller i platinagruppen i det periodiska systemet studerades i detalj för att avslöja kinetiska effekter i hydreringen av cis-metyloleat. Palladium, rutenium, rhodium, platina och iridium användes som katalytiska metaller. Metallhalten på aktivkolbärare var 1 vikt-%. De olika platinametallerna undersöktes för att kartlägga konkurrerande hydrerings- och isomeringsrutter på metallerna. Det visade sig att metallerna i andra raden av det periodiska systemet (Ru, Rh, Pd) är aktivare i isomeringsprocesserna, medan metallerna i tredje raden (Ir, Pt) har en lägre aktivitet. Pd/C valdes bland platinametallerna, för att den är attraktiv ur ekonomisk synvinkel och den är mycket aktiv och selektiv, speciellt jämfört med nickel. Tyngdpunkten i arbetet var utvecklingen av en alternativ, palladiumbaserad hydreringsteknologi som skulle ersätta den traditionella teknologin som är baserad på användningen av nickelkatalysatorer. Palladiumbaserade katalysatorer kan återcirkuleras, de är aktivare och mera resistenta mot syror och de bildar mindre mängder av skadliga transisomerer. För att denna teknologi skall bli ekonomiskt hållbar och konkurrenskraftig, måste den basera sig på de bästa möjliga katalysatorerna, vilket innebär att en optimal kombination av hög aktivitet och selektivitet samt en lång livstid för katalysatorn krävs. Därför inkluderades teknologiska aspekter kraftigt i forskningen. Mycket arbete satsades på design av palladium på en mesoporös kolbärare och undersökning av korrelationerna mellan katalysatorns egenskaper och dess aktivitet i isomeriseringsreaktionerna och i hydreringen av kol-koldubbelbindningarna i reaktantmolekylen. Katalysatorerna karakteriserades med många fysikaliska och kemiska metoder (transmissionselektronmikroskopi (TEM), röntgendiffraktion (XRD), röntgenfotoelektronspektroskopi (XPS), temperaturprogrammerad reduktion (TPR), temperaturprogrammerad desorption (TPD) av kolmonoxid, kemisorption av kolmonoxid, fysisorption av kväve). Temperaturens, vätetryckets och katalysatorkoncentrationens inverkan på fettsyra- och isomersammansättningen hos de hydrerade oljorna bestämdes under kinetiska betingelser, i frånvaro av massöverföringseffekter. Syreavspjälkning genom fullständig dekarboxylering av karboxylgruppen i fettsyramolekylen är det hittills bästa sättet att framställa miljövänlig dieselolja, eftersom linjära paraffiner fås som reaktionsprodukter och en tillsats av dyr vätgas undviks. Deoxygeneringen undersöktes systematiskt på en Pd/C-katalysator (Sibunit) genom att använda mättade fettsyror C16-C20 och C22 som råvara. Produktmolekylen blev en dieselliknande kolvätemolekyl, med en kolatom färre än i utgångsmolekylen. Lika stora dekarboxyleringshastigheter observerades för rena, mättade fettsyror. En jämförelse av deoxygenereringshastigheterna för stearin-, olein- och linolsyra som råvara vid 300oC i närvaro av 1-volymprocent väte på mesoporös Pd/C (Sibunit) avslöjade att katalysatorns aktivitet och selektivitet ökade med en ökande mättningsgrad av reaktantmolekylen. Då stearinsyra användes som utgångsmolekyl, bestod huvudprodukterna av önskade C17-kolväten, medan mängden av aromatiska C17-komponenter ökade, då olein- och linolsyra användes som utgångsmolekyler. Katalysatordeaktiveringen var relativt påfallande vid deoxygeneringen av linolsyra så att endast 3% av fettsyrorna omsattes till produkter i 330 min. Deaktiveringen orsakades av aromatiska C17-komponenter samt av fettsyradimerer, som bildades via en Diels-Alderreaktion. Hydreringen av omättade fettsyror kan därför rekommenderas som ett primärt kemiskt steg i framställningen av miljövänliga dieselprodukter. Målet var också att öka förståelsen av palladiummetallernas roll i nanoskala, speciellt effekten av metallpartiklarna i katalytisk hydrering och deoxygenering. Pd/C-katalysatorer med lika stora halter av Pd syntetiserades och metallens dispersion på bärarmaterialet varierades systematiskt genom en kontrollerad uppväxt av palladiumnanopartiklar på aktiv kolbärare. Metalldispersionens effekt på hydrerings-hastigheten och cis-transförhållandet undersöktes i detalj. En optimal metalldispersion som gav den högsta dekarboxyleringshastigheten hittades. Massöverföringens inverkan på reaktionens hastighet studerades experimentellt och temperaturprogrammerad desorption av kolmonoxid från katalysatorytan undersöktes ingående. Hydrering av växtoljor genomfördes under satsvisa och kontinuerliga betingelser. Både finfördelat Pd/C och katalysatorgranulat användes i experimenten. Ett av målen med arbetet var uppskalningen av hydreringsprocesserna. Med tanke på stora produktionsvolymer var det logiskt att undersöka kontinuerliga hydrerings- och dekarboxyleringsteknologier. En kontinuerlig packad bäddreaktor studerades i laboratorieskala, vilket gav viktig information om katalysatorns långtidsstabilitet och deaktivering. Effekten av rena fettsyror och triglycerider som råvara samt metallpartikelstorleken och palladiumhalten studerades med hjälp av den kontinuerliga reaktorn. Produktionskapaciteten som erhölls med satsvis och kontinuerlig drift jämfördes. Dekarboxyleringen av stearinsyra undersöktes också i en kontinuerlig packad bädd. Omsättningsgraden blev 15% för en stabil katalysator.

Enhancing performance of paper coatings by tailor-made plastic pigments

The paper industry is constantly looking for new ideas for improving paper products while competition and raw material prices are increasing. Many paper products are pigment coated. Coating layer is the top layer of paper, thus by modifying coating pigment also the paper itself can be altered and value added to the final product. In this thesis, synthesis of new plastic and hybrid pigments and their performance in paper and paperboard coating is reported. Two types of plastic pigments were studied: core-shell latexes and solid beads of maleimide copolymers. Core-shell latexes with partially crosslinked hydrophilic polymer core of poly(n-butyl acrylate-co-methacrylic acid) and a hard hydrophobic polystyrene shell were prepared to improve the optical properties of coated paper. In addition, the effect of different crosslinkers was analyzed and the best overall performance was achieved by the use of ethylene glycol dimethacrylate (EGDMA). Furthermore, the possibility to modify core-shell latex was investigated by introducing a new polymerizable optical brightening agent, 1-[(4-vinylphenoxy)methyl]-4-(2-henylethylenyl)benzene which gave promising results. The prepared core-shell latex pigments performed smoothly also in pilot coating and printing trials. The results demonstrated that by optimizing polymer composition, the optical and surface properties of coated paper can be significantly enhanced. The optimal reaction conditions were established for thermal imidization of poly(styrene-co-maleimide) (SMI) and poly(octadecene-co-maleimide) (OMI) from respective maleic anhydride copolymer precursors and ammonia in a solvent free process. The obtained aqueous dispersions of nanoparticle copolymers exhibited glass transition temperatures (Tg) between 140-170ºC and particle sizes from 50-230 nm. Furthermore, the maleimide copolymers were evaluated in paperboard coating as additional pigments. The maleimide copolymer nanoparticles were partly imbedded into the porous coating structure and therefore the full potential of optical property enhancement for paperboard was not achieved by this method. The possibility to modify maleimide copolymers was also studied. Modifications were carried out via N-substitution by replacing part of the ammonia in the imidization reaction with amines, such as triacetonediamine (TAD), aspartic acid (ASP) and fluorinated amines (2,2,2- trifluoroethylamine, TFEA and 2,2,3,3,4,4,4-heptafluorobuthylamine, HFBA). The obtained functional nanoparticles varied in size between 50-217 nm and their Tg from 150-180ºC. During the coating process the produced plastic pigments exhibited good runnability. No significant improvements were achieved in light stability with TAD modified copolymers whereas nanoparticles modified with aspartic acid and those containing fluorinated groups showed the desired changes in surface properties of the coated paperboard. Finally, reports on preliminary studies with organic-inorganic hybrids are presented. The hybrids prepared by an in situ polymerization reaction consisted of 30 wt% poly(styrene- co-maleimide) (SMI) and high levels of 70 wt% inorganic components of kaolin and/or alumina trihydrate. Scanning Electron Microscopy (SEM) images and characterization by Fourier Transform Infrared Spcetroscopy (FTIR) and X-Ray Diffraction (XRD) revealed that the hybrids had conventional composite structure and inorganic components were covered with precipitated SMI nanoparticles attached to the surface via hydrogen bonding. In paper coating, the hybrids had a beneficial effect on increasing gloss levels.

2-(aminometyyli)pyridiini ligandin kompleksoituminen nikkelin kanssa eri liuottimissa

Kandidaatintyön tavoitteena oli tutkia 2-(aminometyyli)pyridiini ligandin kompleksoitumista nikkeli(II) ionin kanssa vesiliuoksissa ja eri orgaanisissa liuotinseoksissa. Työ tehtiin osana laajempaa tutkimusta, jossa pyritään määrittämään nikkelille spesifisiä erotusmateriaaleja ion imprinting tekniikkaa hyväksikäyttäen. Koesarjat sekä näihin liittyvä mittaukset suoritettiin kaikki huoneen lämmössä sekä normaalissa ilman paineessa. Koesarjojen liuosfaaseista määritettiin UV/Vis spektrofotometrisesti spektrit, joiden perusteella piirrettiin Job Plot kuvaajat. Kuvaajien havaittiin vastaavan aikaisemmissa tutkimuksissa määritettyjä kuvaajia sekä matemaattisesti laskettuja huippuarvoja. Saostuneiden kiintoaineiden koostumukset määritettiin XRD ja IR mittauksilla. Tuloksien perusteella todettiin 1:2 kompleksin saostuvan lähes poikkeuksetta kaikista saostuneista näytteistä. Mittaustuloksista johtopäätöksinä voidaan todeta liuotinseoksien ja veden määrän vaikuttavan muodostuneen kompleksin kiderakenteeseen, mutta ei saostuvaan kompleksiin.

Treatment of Fe-containing Acid Mine Waters in Fixed Bed Adsorption Column with Calcite Side-Stone

The acid mining drainage is considered the most significant environmental pollution problem around the world for the extensive formation acidic leachates containing heavy metals. Adsorption is widely used methods in water treatment due to it easy operation and the availability of a wide variety of commercial adsorbent (low cost). The primary goal of this thesis was to investigate the efficiency of neutralizing agents, CaCO3 and CaSiO3, and metal adsorption materials with unmodified limestone from Company Nordkalk Oy. In addition to this, the side materials of limestone mining were tested for iron adsorption from acidic model solution. This study was executed at Lappeenranta University of Technology, Finland. The work utilised fixed-bed adsorption column as the main equipment and large fluidized column. Atomic absorption spectroscopy (AAS) and x-ray diffraction (XRD) was used to determine ferric removal and the composition of material respectively. The results suggest a high potential for the studied materials to be used a low cost adsorbents in acid mine drainage treatment. From the two studied adsorbents, the FS material was more suitable than the Gotland material. Based on the findings, it is recommended that further studies might include detailed analysis of Gotland materials.

Methyl and ethyl chloride synthesis in microreactors

Methyl chloride is an important chemical intermediate with a variety of applications. It is produced today in large units and shipped to the endusers. Most of the derived products are harmless, as silicones, butyl rubber and methyl cellulose. However, methyl chloride is highly toxic and flammable. On-site production in the required quantities is desirable to reduce the risks involved in transportation and storage. Ethyl chloride is a smaller-scale chemical intermediate that is mainly used in the production of cellulose derivatives. Thus, the combination of onsite production of methyl and ethyl chloride is attractive for the cellulose processing industry, e.g. current and future biorefineries. Both alkyl chlorides can be produced by hydrochlorination of the corresponding alcohol, ethanol or methanol. Microreactors are attractive for the on-site production as the reactions are very fast and involve toxic chemicals. In microreactors, the diffusion limitations can be suppressed and the process safety can be improved. The modular setup of microreactors is flexible to adjust the production capacity as needed. Although methyl and ethyl chloride are important chemical intermediates, the literature available on potential catalysts and reaction kinetics is limited. Thus the thesis includes an extensive catalyst screening and characterization, along with kinetic studies and engineering the hydrochlorination process in microreactors. A range of zeolite and alumina based catalysts, neat and impregnated with ZnCl2, were screened for the methanol hydrochlorination. The influence of zinc loading, support, zinc precursor and pH was investigated. The catalysts were characterized with FTIR, TEM, XPS, nitrogen physisorption, XRD and EDX to identify the relationship between the catalyst characteristics and the activity and selectivity in the methyl chloride synthesis. The acidic properties of the catalyst were strongly influenced upon the ZnCl2 modification. In both cases, alumina and zeolite supports, zinc reacted to a certain amount with specific surface sites, which resulted in a decrease of strong and medium Brønsted and Lewis acid sites and the formation of zinc-based weak Lewis acid sites. The latter are highly active and selective in methanol hydrochlorination. Along with the molecular zinc sites, bulk zinc species are present on the support material. Zinc modified zeolite catalysts exhibited the highest activity also at low temperatures (ca 200 °C), however, showing deactivation with time-onstream. Zn/H-ZSM-5 zeolite catalysts had a higher stability than ZnCl2 modified H-Beta and they could be regenerated by burning the coke in air at 400 °C. Neat alumina and zinc modified alumina catalysts were active and selective at 300 °C and higher temperatures. However, zeolite catalysts can be suitable for methyl chloride synthesis at lower temperatures, i.e. 200 °C. Neat γ-alumina was found to be the most stable catalyst when coated in a microreactor channel and it was thus used as the catalyst for systematic kinetic studies in the microreactor. A binder-free and reproducible catalyst coating technique was developed. The uniformity, thickness and stability of the coatings were extensively characterized by SEM, confocal microscopy and EDX analysis. A stable coating could be obtained by thermally pretreating the microreactor platelets and ball milling the alumina to obtain a small particle size. Slurry aging and slow drying improved the coating uniformity. Methyl chloride synthesis from methanol and hydrochloric acid was performed in an alumina-coated microreactor. Conversions from 4% to 83% were achieved in the investigated temperature range of 280-340 °C. This demonstrated that the reaction is fast enough to be successfully performed in a microreactor system. The performance of the microreactor was compared with a tubular fixed bed reactor. The results obtained with both reactors were comparable, but the microreactor allows a rapid catalytic screening with low consumption of chemicals. As a complete conversion of methanol could not be reached in a single microreactor, a second microreactor was coupled in series. A maximum conversion of 97.6 % and a selectivity of 98.8 % were reached at 340°C, which is close to the calculated values at a thermodynamic equilibrium. A kinetic model based on kinetic experiments and thermodynamic calculations was developed. The model was based on a Langmuir Hinshelwood-type mechanism and a plug flow model for the microreactor. The influence of the reactant adsorption on the catalyst surface was investigated by performing transient experiments and comparing different kinetic models. The obtained activation energy for methyl chloride was ca. two fold higher than the previously published, indicating diffusion limitations in the previous studies. A detailed modeling of the diffusion in the porous catalyst layer revealed that severe diffusion limitations occur starting from catalyst coating thicknesses of 50 μm. At a catalyst coating thickness of ca 15 μm as in the microreactor, the conditions of intrinsic kinetics prevail. Ethanol hydrochlorination was performed successfully in the microreactor system. The reaction temperature was 240-340°C. An almost complete conversion of ethanol was achieved at 340°C. The product distribution was broader than for methanol hydrochlorination. Ethylene, diethyl ether and acetaldehyde were detected as by-products, ethylene being the most dominant by-product. A kinetic model including a thorough thermodynamic analysis was developed and the influence of adsorbed HCl on the reaction rate of ethanol dehydration reactions was demonstrated. The separation of methyl chloride using condensers was investigated. The proposed microreactor-condenser concept enables the production of methyl chloride with a high purity of 99%.

Pulsed electric field assisted sol-gel preparation of TiO2 particles and their photocatalytic properties

The objective of this thesis was to study the effect of pulsed electric field on the preparation of TiO2 nanoparticles via sol-gel method. The literature part deals with properties of different TiO2 crystal forms, principles of photocatalysis, sol-gel method and pulsed electric field processing. It was expected that the pulsed electric field would have an influence on crystallite size, specific surface area, polymorphism and photocatalytic activity of produced particles. TiO2 samples were prepared by using different frequencies and treatment times of pulsed electric field. The properties of produced TiO2 particles were examined X-ray diffraction (XRD), Raman spectroscopy and BET surface area analysis. The photocatalytic activities of produced TiO2 particles were determined by using them as photocatalysts for the degradation of formic acid under UVA-light. The photocatalytic activities of samples produced with sol-gel method were also compared with the commercial TiO2 powder Aeroxide® (Evonic Degussa GmbH). Pulsed electric field did not have an effect on the morphology of particles. Results from XRD and Raman analysis showed that all produced TiO2 samples were pure anatase. However, pulsed electric field did have an effect on crystallite size, specific surface area and photocatalytic activity of TiO2 particles. Generally, the crystallite sizes were smaller, specific surface areas larger and initial formic acid degradation rates higher for samples that were produced by applying the pulsed electric field. The higher photocatalytic activities were attributed to larger surface areas and smaller crystallite sizes. Though, with all of the TiO2 samples produced by the sol-gel method the initial formic acid degradation rates were significantly slower than with the commercial TiO2 powder.

Surface studies of limestones and dolostones : characterisation using various techniques and batch dissolution experiments with hydrochloric acid solutions

In this thesis, stepwise titration with hydrochloric acid was used to obtain chemical reactivities and dissolution rates of ground limestones and dolostones of varying geological backgrounds (sedimentary, metamorphic or magmatic). Two different ways of conducting the calculations were used: 1) a first order mathematical model was used to calculate extrapolated initial reactivities (and dissolution rates) at pH 4, and 2) a second order mathematical model was used to acquire integrated mean specific chemical reaction constants (and dissolution rates) at pH 5. The calculations of the reactivities and dissolution rates were based on rate of change of pH and particle size distributions of the sample powders obtained by laser diffraction. The initial dissolution rates at pH 4 were repeatedly higher than previously reported literature values, whereas the dissolution rates at pH 5 were consistent with former observations. Reactivities and dissolution rates varied substantially for dolostones, whereas for limestones and calcareous rocks, the variation can be primarily explained by relatively large sample standard deviations. A list of the dolostone samples in a decreasing order of initial reactivity at pH 4 is: 1) metamorphic dolostones with calcite/dolomite ratio higher than about 6% 2) sedimentary dolostones without calcite 3) metamorphic dolostones with calcite/dolomite ratio lower than about 6% The reactivities and dissolution rates were accompanied by a wide range of experimental techniques to characterise the samples, to reveal how different rocks changed during the dissolution process, and to find out which factors had an influence on their chemical reactivities. An emphasis was put on chemical and morphological changes taking place at the surfaces of the particles via X-ray Photoelectron Spectroscopy (XPS) and Scanning Electron Microscopy (SEM). Supporting chemical information was obtained with X-Ray Fluorescence (XRF) measurements of the samples, and Inductively Coupled Plasma-Mass Spectrometry (ICP-MS) and Inductively Coupled Plasma-Optical Emission Spectrometry (ICP-OES) measurements of the solutions used in the reactivity experiments. Information on mineral (modal) compositions and their occurrence was provided by X-Ray Diffraction (XRD), Energy Dispersive X-ray analysis (EDX) and studying thin sections with a petrographic microscope. BET (Brunauer, Emmet, Teller) surface areas were determined from nitrogen physisorption data. Factors increasing chemical reactivity of dolostones and calcareous rocks were found to be sedimentary origin, higher calcite concentration and smaller quartz concentration. Also, it is assumed that finer grain size and larger BET surface areas increase the reactivity although no certain correlation was found in this thesis. Atomic concentrations did not correlate with the reactivities. Sedimentary dolostones, unlike metamorphic ones, were found to have porous surface structures after dissolution. In addition, conventional (XPS) and synchrotron based (HRXPS) X-ray Photoelectron Spectroscopy were used to study bonding environments on calcite and dolomite surfaces. Both samples are insulators, which is why neutralisation measures such as electron flood gun and a conductive mask were used. Surface core level shifts of 0.7 ± 0.1 eV for Ca 2p spectrum of calcite and 0.75 ± 0.05 eV for Mg 2p and Ca 3s spectra of dolomite were obtained. Some satellite features of Ca 2p, C 1s and O 1s spectra have been suggested to be bulk plasmons. The origin of carbide bonds was suggested to be beam assisted interaction with hydrocarbons found on the surface. The results presented in this thesis are of particular importance for choosing raw materials for wet Flue Gas Desulphurisation (FGD) and construction industry. Wet FGD benefits from high reactivity, whereas construction industry can take advantage of slow reactivity of carbonate rocks often used in the facades of fine buildings. Information on chemical bonding environments may help to create more accurate models for water-rock interactions of carbonates.

Influence of Pulsed-Electric Field Irradiation in Crystallization

The growing pharmaceutical interest, among others, in the polymorphic composition of the emerging solid end-products from production processes has been traced to the need for attainment of high product purity. This is more so as the presence of different polymorphs may constitute physical impurity of the product. Hence, the need for optimization of the yield of desired product component(s) through controlled crystallization kinetics for instance. This study was carried out to investigate the impact of pulsed electric field (PEF) irradiation on the crystal morphology of glycine obtained by cooling crystallization (without seeding) from commercial glycine sample in distilled deionized water solution. In doing so, three different pulse frequencies (294, 950 and 145 Hz) and a case without PEF were studied at three cooling rates (5, 10 and 20 ºC/h). The crystal products obtained were analyzed for polymorphic composition by powder x-ray diffraction (PXRD) and Fourier transform infrared (FTIR) spectroscopy while the particles characterization was done on Morphologi G3. The results obtained from this study showed that pulsed electric field irradiation had significant impact on metastability of the aqueous solution as well as on the polymorphic composition of the end product. With increasing PEF frequency applied, nucleation started earlier and the γ-glycine polymorph content of the product crystals increased. These were found to have been aided by cooling rate, as the most significant effect was observed at 5 ºC/h. It was also discovered that PEF application had no measurable impact on the pH of the aqueous solution as well as the size distribution of the particles. Cooling on the contrary was believed to be responsible for the broadening of the particle size distribution with a downward shift of the lower limit of the raw material from about 100 μm to between 10 and 50 μm.

Hyperfine interactions in the new Fe-based superconducting structures and related magnetic phases

This thesis is devoted to the study of the hyperfine properties in iron-based superconductors and the synthesis of these compounds and related phases. During this work polycrystalline chalcogenide samples with stoichiometry 1:1 (FeTe1-χSχ, FeSe1-x) and pnictide samples with stoichiometry 1:2:2 (BaFe2(As1-χPχ)2, EuFe2(As1-x Px)2) were synthesized by solid-state reaction methods in vacuum and in a protecting Ar atmosphere. In several cases post-annealing in oxygen atmosphere was employed. The purity and superconducting properties of the obtained samples were checked with X-ray diffraction, SQUID and resistivity measurements. For studies of the magnetic properties of the investigated samples Mössbauer spectroscopy was used. Using low-temperature measurements around Tc and various values of the source velocity the hyperfine interactions were obtained and the magnetic and structural properties in the normal and superconducting states could be studied. Mössbauer measurements together with XRD characterization were also used for the detection of impurity phases. DFT calculations were used for the theoretical study of Mössbauer parameters for pnictide-based ᴻsamples BaFe2(As1-xPx)2 and EuFe2(As1-xPx)2.