Ball Bearing Model Performance on Various Sized Rotors with and without Centrifugal and Gyroscopic Forces

Bearing performance signi cantly a ects the dynamic behaviors and estimated working life of a rotating system. A common bearing type is the ball bearing, which has been under investigation in numerous published studies. The complexity of the ball bearing models described in the literature varies. Naturally, model complexity is related to computational burden. In particular, the inclusion of centrifugal forces and gyroscopic moments signi cantly increases the system degrees of freedom and lengthens solution time. On the other hand, for low or moderate rotating speeds, these e ects can be neglected without signi cant loss of accuracy. The objective of this paper is to present guidelines for the appropriate selection of a suitable bearing model for three case studies. To this end, two ball bearing models were implemented. One considers high-speed forces, and the other neglects them. Both models were used to study a three structures, and the simulation results were.

Measurement of the air permeability profile on SC paper machine

Tämän diplomityön tarkoituksena oli asentaa ja kehittää UPM-Kymmene Rauman tehtaiden PK2:lle luotettava ja toimiva ilmanläpäisyprofiilin mittaus. Työn tarkoituksena oli myös kartoittaa tietoja ilmanläpäisyprofiiliin vaikuttavista seikoista sekä mahdollisuuksista säätää ilmanläpäisyprofiilia. Lisäksi työn tavoitteena oli löytää toimiva menetelmä verrata online mitattua ilmanläpäisyprofiilia laboratoriossa mitattuun ilmanläpäisyprofiiliin online mittauksen luotettavuuden näkökulmasta. Työn aikana selvitettiin myös ilmanläpäisyprofiilin mittauksen mahdollisuutta superkalanteroidusta SC paperista. Työn kirjallisessa osassa käsiteltiin paperin huokoisuutta ja ilmanläpäisyä, huokoisuustasoon ja huokoisuus profiiliin vaikuttavia tekijöitä, ilmanläpäisevyyden merkitystä SC paperin valmistukselle ja SC paperin painettavuudelle sekä ilmanläpäisevyyden laboratorio- sekä online mittausta. Kirjallisessa osassa käsiteltiin myös Honeywellin uutta Poros ilmanläpäisysensoria. Työn kokeellisessa osassa tutkittiin ilmanläpäisyprofiilimittauksen luotettavuutta CD ja MD suunnassa sekä laboratorio- ja online-mittausten välisiä eroavaisuuksia ennen PK2 uusintaa. PK2 uusinnan jälkeen kokeellisessa osassa keskityttiin luotettavuuden varmentamiseen CD ja MD suunnassa sekä kartoittamaan tekijöitä, jotka aiheuttivat pieniä tasoeroja mittausten välillä. Mittaukset todettiin luotettaviksi ja niiden pohjalta suoritettiin mitattujen online profiilien välisiä vertailuja. Ilmanläpäisyprofiililla todettiin olevan positiivinen korrelaatio neliömassaprofiilin ja kosteusprofiilin kanssa sekä negatiivinen korrelaatio tuhkaprofiilin kanssa. PK2 uusinnan yhteydessä tehtiin koeajoja, jotka liittyivät laadunoptimointiin viira- ja puristinosalla. Koeajoissa tutkittujen asioiden lisäksi tutkittiin muutettujen parametrien vaikutusta ilmanläpäisyprofiiliin. Höyrylaatikon vaikutusta ilmanläpäisyprofiiliin tutkittiin säätöjen virityksen yhteydessä.

High-speed solid-rotor induction machine – calculation program

The aim of this thesis is to utilize the technology developed at LUT and to provide an easy tool for high-speed solid-rotor induction machine preliminary design. Computer aided design tool MathCAD has been chosen as the environment for realizing the calculation program. Four versions of the design program have been made depending on the motor rotor type. The first rotor type is an axially slitted solid-rotor with steel end rings. The next one is an axially slitted solid-rotor with copper end rings. The third machine type is a solid rotor with deep, rectangular copper bars and end rings (squirrel cage). And the last one is a solid-rotor with round copper bars and end rings (squirrel cage). Each type of rotor has its own specialties but a general thread of design is common. This paper follows the structure of the calculating program and explains some features and formulas. The attention is concentrated on the difference between laminated and solid-rotor machine design principles. There is no deep analysis of the calculation ways are presented. References for all solution methods appearing during the design procedure are given for more detailed studying. This thesis pays respect to the latest innovations in solid-rotor machines theory. Rotor ends’ analytical calculation follows the latest knowledge in this field. Correction factor for adjusting the rotor impedance is implemented. The purpose of the created design program is to calculate the preliminary dimensions of the machine according to initial data. Obtained results are not recommended for exact machine development. Further more detailed design should be done in a finite element method application. Hence, this thesis is a practical tool for the prior evaluating of the high-speed machine with different solid-rotor types parameters.

Liminal Monster and the Conflict Between Human and Machine: The Shrike in Dan Simmons’ Hyperion and The Fall of Hyperion

Tarkastelen tutkielmassani Dan Simmonsin kaksiosaista tieteisfiktioteosta, joka koostuu romaaneista Hyperion ja The Fall of Hyperion. Keskityn teoksissa esiintyvään Shrike-hirviöön, joka edustaa ihmiskunnan pelkäämää potentiaalista konfliktia ihmisten ja koneiden välillä. Pelko ja konflikti ovat keskeisiä teemoja paitsi tieteisfiktiossa, myös hirviöteoksissa yleensä, ja näiden kahden käyttö samassa kertomuksessa luo otolliset edellytykset nyky-yhteiskunnan ahdistusten kuvaamiseen. Hirviöitä ja tieteisfiktiota on tätä nykyä tutkittu melko laajalti, mutta Shrike on aiemmin jäänyt vähälle huomiolle. Lähtökohtaisen teoreettisen viitekehyksen tutkimukselleni ovat luoneet Jeffrey Cohenin Monster Theory: Reading Culture, Stephen Asman On Monsters: An Unnatural History of Our Worst Fears sekä Holly Lynn Baumgartnerin ja Roger Davisin At the Interface: Hosting the Monster. Teoksista kokoamani hirviöteorian kautta tarkastelen sitä, miten Shriken puoliksi orgaaninen ja puoliksi keinotekoinen keho heijastaa niitä romaaneissa esiintyviä osa-alueita, joista tulevaisuudenpelko ja ihmisten ja koneiden väliseen konfliktin uhka koostuu. Koska Shrike on puoliksi orgaaninen ja puoliksi keinotekoinen, se on näiden ominaisuuksien kynnyksellä; tässä risteytyneessä kehossa yhdistyvät molemmat ääripäät, jolloin tämä keho myös symboloi osapuolten välistä konfliktia. Konfliktin lisäksi Shrike ilmentää niitä vastakkaisuuksia, joista ihmisten ja koneiden välisen konfliktin pelko rakentuu: itseyttä ja toiseutta, houkuttelevuutta ja luotaantyöntävyyttä, menneisyyttä ja tulevaisuutta sekä utopiaa ja dystopiaa.

Parasitic Order Machine. A Sociology and Ontology of Information Securing

This study examines information security as a process (information securing) in terms of what it does, especially beyond its obvious role of protector. It investigates concepts related to ‘ontology of becoming’, and examines what it is that information securing produces. The research is theory driven and draws upon three fields: sociology (especially actor-network theory), philosophy (especially Gilles Deleuze and Félix Guattari’s concept of ‘machine’, ‘territory’ and ‘becoming’, and Michel Serres’s concept of ‘parasite’), and information systems science (the subject of information security). Social engineering (used here in the sense of breaking into systems through non-technical means) and software cracker groups (groups which remove copy protection systems from software) are analysed as examples of breaches of information security. Firstly, the study finds that information securing is always interruptive: every entity (regardless of whether or not it is malicious) that becomes connected to information security is interrupted. Furthermore, every entity changes, becomes different, as it makes a connection with information security (ontology of becoming). Moreover, information security organizes entities into different territories. However, the territories – the insides and outsides of information systems – are ontologically similar; the only difference is in the order of the territories, not in the ontological status of entities that inhabit the territories. In other words, malicious software is ontologically similar to benign software; they both are users in terms of a system. The difference is based on the order of the system and users: who uses the system and what the system is used for. Secondly, the research shows that information security is always external (in the terms of this study it is a ‘parasite’) to the information system that it protects. Information securing creates and maintains order while simultaneously disrupting the existing order of the system that it protects. For example, in terms of software itself, the implementation of a copy protection system is an entirely external addition. In fact, this parasitic addition makes software different. Thus, information security disrupts that which it is supposed to defend from disruption. Finally, it is asserted that, in its interruption, information security is a connector that creates passages; it connects users to systems while also creating its own threats. For example, copy protection systems invite crackers and information security policies entice social engineers to use and exploit information security techniques in a novel manner.

A conspectus on estimating function theory and its applicability to recurrent modeling issues in forest biometry

Summary

Impingement jet cooling of end windings in a high-speed electric machine

The rotational speed of high-speed electric machines is over 15 000 rpm. These machines are compact in size when compared to the power rate. As a consequence, the heat fluxes are at a high level and the adequacy of cooling becomes an important design criterion. In the high-speed machines, the air gap between the stator and rotor is a narrow flow channel. The cooling air is produced with a fan and the flow is then directed to the air gap. The flow in the gap does not provide sufficient cooling for the stator end windings, and therefore additional cooling is required. This study investigates the heat transfer and flow fields around the coil end windings when cooling jets are used. As a result, an innovative and new assembly is introduced for the cooling jets, with the benefits of a reduced amount of hot spots, a lower pressure drop, and hence a lower power need for the cooling fan. The gained information can also be applied to improve the cooling of electric machines through geometry modifications. The objective of the research is to determine the locations of the hot spots and to find out induced pressure losses with different jet alternatives. Several possibilities to arrange the extra cooling are considered. In the suggested approach cooling is provided by using a row of air jets. The air jets have three main tasks: to cool the coils effectively by direct impingement jets, to increase and cool down the flow that enters the coil end space through the air gap, and to ensure the correct distribution of the flow by forming an air curtain with additional jets. One important aim of this study is the arrangement of cooling jets in such manner that hot spots can be avoided to wide extent. This enables higher power density in high-speed motors. This cooling system can also be applied to the ordinary electric machines when efficient cooling is needed. The numerical calculations have been performed using a commercial Computational Fluid Dynamics software. Two geometries have been generated: cylindrical for the studied machine and Cartesian for the experimental model. The main parameters include the positions, arrangements and number of jets, the jet diameters, and the jet velocities. The investigated cases have been tested with two widely used turbulence models and using a computational grid of over 500 000 cells. The experimental tests have been made by using a simplified model for the end winding space with cooling jets. In the experiments, an emphasis has been given to flow visualisation. The computational analysis shows good agreement with the experimental results. Modelling of the cooling jet arrangement enables also a better understanding of the complex system of heat transfer at end winding space.

Pulp Fractionation in a Pilot Paper Machine

Tämän diplomityön tarkoituksena on tutkia paperimassan jakautumiseen vaikuttavia tekijöitä paperinvalmistusprosessissa. Työn empiirisen osan tavoitteena on analysoida perälaatikon hienoainepitoisuuden ja paperimassan virtausnopeuden vaikutusta paperimassan jakautumiseen pilottipaperikoneessa, sekä selvittää voidaanko näitä prosessiparametreja optimoimalla saavuttaa merkittävää retention, vedenpoiston ja kaksipuolisuuden parantumista. Työn teoreettinen osa sisältää kirjallisuuskatsauksen märänpään kemiasta ja yhteenvedon aikaisemmasta tutkimuksesta koskien paperimassan jakautumista paperinvalmistusprosessissa. Työn empiirisessä osassa on tutkittu perälaatikon hienoainepitoisuuden ja paperimassan virtausnopeuden vaikutusta retentioon, vedenpoistoon ja paperimassan jakautumiseen Papricanin pilottipaperikoneessa. Analyysissä on käytetty yhteensovitettua dataa, joka on saatu kattavien pilottipaperikonekokeiden ja taulukkolaskentaohjelmalla toteutettujen staattisten simulointimallien avulla. Simulointimalleissa perälaatikon hienoainepitoisuus on 30-55%, sekä paperimassan virtausnopeudet ovat 2470 L/min, 3870 L/min ja 5230 L/min. Muut prosessiparametrit on vakioitu, eikä retentioainetta käytetty. Retentio pilottipaperikoneessa oli 55-82% riippuen perälaatikon hienoainepitoisuudesta ja paperimassan virtausnopeudesta. Perälaatikon hienoainepitoisuuden ja retention välillä oli voimakas negatiivinen korrelaatio. Myös paperimassan virtausnopeuden ja retention välillä oli negatiivinen korrelaatio. Mitä alhaisempi retentio, sitä enemmän hienoainesta kerääntyi systeemiin. Hienoaineen huuhtoutuminen paperirainasta korreloi vedenpoistoon: pienemmällä paperimassan virtausnopeudella enemmän sekä vettä että hienoainetta poistui viirapuolelta, ja suuremmalla paperimassan virtausnopeudella saman verran sekä vettä että hienoainetta poistui rainan molemmilta puolilta. Paras paperirainan kaksipuolisuus saavutettiin korkeilla perälaatikon hienoainepitoisuuksilla (50% ja 55%) suurilla paperimassan virtausnopeuksilla (3870 L/min ja 5230 L/min).

Repeatability ofthe recipe parameters of a corrugated board machine against warp

The warp of corrugated board is the most prevalent quality problem incorrugated board industry. Nowadays corrugators provide high quality board but there often occurs a warp problem within the production of some board grades. One of the main reasons for that are the humidity and the temperature levels of the raw materials. The goal of the research is to find out howthe adjusted corrugator recipe parameters required for appropriate running of the corrugated board are repeatable for the considered board grades, how the temperature and humidity imbalances of the raw material papers influence on the warpformation of the finished board. Furthermore, the solutions for preventing warpof corrugated board are presented in the thesis.

Machine vision measurement system for paper printability assessments

This work had two primary objectives: 1) to produce a working prototype for automated printability assessment and 2) to perform a study of available machine vision and other necessary hardware solutions. The three printability testing methods, IGT Picking,He¬liotest, and mottling, considered in this work have several different requirements and the task was to produce a single automated testing system suitable for all methods. A system was designed and built and its performance was tested using the Heliotest. Working proto¬types are important tools for implementing theoretical methods into practical systems and testing and demonstrating the methodsin real life conditions. The system was found to be sufficient for the Heliotest method. Further testing and possible modifications related to other two test methods were left for future works. A short study of available systems and solutions concerning image acquisition of machine vision was performed. The theoretical part of this study includes lighting systems, optical systems and image acquisition tools, mainly cameras and the underlying physical aspects for each portion.

Retinal Image Analysis Using Machine Vision

The topic of this thesis is studying how lesions in retina caused by diabetic retinopathy can be detected from color fundus images by using machine vision methods. Methods for equalizing uneven illumination in fundus images, detecting regions of poor image quality due toinadequate illumination, and recognizing abnormal lesions were developed duringthe work. The developed methods exploit mainly the color information and simpleshape features to detect lesions. In addition, a graphical tool for collecting lesion data was developed. The tool was used by an ophthalmologist who marked lesions in the images to help method development and evaluation. The tool is a general purpose one, and thus it is possible to reuse the tool in similar projects.The developed methods were tested with a separate test set of 128 color fundus images. From test results it was calculated how accurately methods classify abnormal funduses as abnormal (sensitivity) and healthy funduses as normal (specificity). The sensitivity values were 92% for hemorrhages, 73% for red small dots (microaneurysms and small hemorrhages), and 77% for exudates (hard and soft exudates). The specificity values were 75% for hemorrhages, 70% for red small dots, and 50% for exudates. Thus, the developed methods detected hemorrhages accurately and microaneurysms and exudates moderately.