53 resultados para jet quenching
em Doria (National Library of Finland DSpace Services) - National Library of Finland, Finland
Resumo:
The rotational speed of high-speed electric machines is over 15 000 rpm. These machines are compact in size when compared to the power rate. As a consequence, the heat fluxes are at a high level and the adequacy of cooling becomes an important design criterion. In the high-speed machines, the air gap between the stator and rotor is a narrow flow channel. The cooling air is produced with a fan and the flow is then directed to the air gap. The flow in the gap does not provide sufficient cooling for the stator end windings, and therefore additional cooling is required. This study investigates the heat transfer and flow fields around the coil end windings when cooling jets are used. As a result, an innovative and new assembly is introduced for the cooling jets, with the benefits of a reduced amount of hot spots, a lower pressure drop, and hence a lower power need for the cooling fan. The gained information can also be applied to improve the cooling of electric machines through geometry modifications. The objective of the research is to determine the locations of the hot spots and to find out induced pressure losses with different jet alternatives. Several possibilities to arrange the extra cooling are considered. In the suggested approach cooling is provided by using a row of air jets. The air jets have three main tasks: to cool the coils effectively by direct impingement jets, to increase and cool down the flow that enters the coil end space through the air gap, and to ensure the correct distribution of the flow by forming an air curtain with additional jets. One important aim of this study is the arrangement of cooling jets in such manner that hot spots can be avoided to wide extent. This enables higher power density in high-speed motors. This cooling system can also be applied to the ordinary electric machines when efficient cooling is needed. The numerical calculations have been performed using a commercial Computational Fluid Dynamics software. Two geometries have been generated: cylindrical for the studied machine and Cartesian for the experimental model. The main parameters include the positions, arrangements and number of jets, the jet diameters, and the jet velocities. The investigated cases have been tested with two widely used turbulence models and using a computational grid of over 500 000 cells. The experimental tests have been made by using a simplified model for the end winding space with cooling jets. In the experiments, an emphasis has been given to flow visualisation. The computational analysis shows good agreement with the experimental results. Modelling of the cooling jet arrangement enables also a better understanding of the complex system of heat transfer at end winding space.
Resumo:
The present paper is devoted to the results of experimental research undertaken into photocatalytical oxidation (PCO) of aqueous solutions of de-icing agents and aqueous extract of jet fuel. The report consists of introduction, literature review, description of materials and methods, discussion of results and conclusions. TiO2 was selected as a photocatalyst for the experiments with synthetic solutions of ethylene glycol, 2-ethoxyethanol and aqueous extract of jet fuel. To explain the PCO mechanisms affecting certain behaviour of de-icing agent under distinctive conditions, the following factors were studied: the impact of initial concentration of pollutant, the role of pH, the presence of tert-butanol as OH·-radicals scavenger and mineral admixtures. PCO under solar radiation performed in two ways: catalysed by irradiated TiO2 slurry or by TiO2 attached to buoyant hollow glass micro-spheres. Special attention was paid to the energy-saving PCO with reduced intensity mixing of the slurry. The effect of PCO was assessed by determination of residual chemical oxygen demand of solution (COD) and by measuring of concentration of glycols. The PCO process efficiency was assumed to be dependent on the TiO2 suspension fractional composition. Thus, the following effects of solutions’ media were viewed: presence of organic admixtures, pH influence, mixing mode during the PCO. The effects of mineral admixtures - Ca2+, Fe3+/2+, Mn2+, SO42- - that are often present in natural and wastewater systems or produced during the degradation of organic pollutants and which can affect the rate of PCO of de-icing agents, were also investigated.
Resumo:
Suihku/viira-nopeussuhde on perälaatikon huulisuihkun ja viiran välinen nopeusero. Se vaikuttaa suuresti paperin ja kartongin loppuominaisuuksiin, kuten formaatioon sekä kuituorientaatioon ja näin ollen paperin lujuusominaisuuksiin. Tämän johdosta on erityisen tärkeää tietää todellinen suihku/viira-nopeussuhde paperin- ja kartonginvalmistuksessa. Perinteinen suihku/viira-nopeussuhteen määritysmenetelmä perustuu perälaatikon kokonaispaineeseen. Tällä menetelmällä kuitenkin todellinen huulisuihkun nopeus saattaa usein jäädä tietämättä johtuen mahdollisesta virheellisestä painemittarin kalibroinnista sekä laskuyhtälön epätarkkuuksista. Tämän johdosta on kehitetty useita reaaliaikaisia huulisuihkun mittausmenetelmiä. Perälaatikon parametrien optimaaliset asetukset ovat mahdollista määrittää ja ylläpitää huulisuihkun nopeuden “on-line” määrityksellä. Perälaatikon parametrejä ovat mm. huulisuihku, huuliaukon korkeusprofiili, reunavirtaukset ja syöttövirtauksen tasaisuus. Huulisuihkun nopeuden on-line mittauksella paljastuu myös muita perälaatikon ongelmakohtia, kuten mekaaniset viat, joita on perinteisesti tutkittu aikaa vievillä paperin ja kartongin lopputuoteanalyyseillä.
Resumo:
Fine powders of minerals are used commonly in the paper and paint industry, and for ceramics. Research for utilizing of different waste materials in these applications is environmentally important. In this work, the ultrafine grinding of two waste gypsum materials, namely FGD (Flue Gas Desulphurisation) gypsum and phosphogypsum from a phosphoric acid plant, with the attrition bead mill and with the jet mill has been studied. The ' objective of this research was to test the suitability of the attrition bead mill and of the jet mill to produce gypsum powders with a particle size of a few microns. The grinding conditions were optimised by studying the influences of different operational grinding parameters on the grinding rate and on the energy consumption of the process in order to achieve a product fineness such as that required in the paper industry with as low energy consumption as possible. Based on experimental results, the most influential parameters in the attrition grinding were found to be the bead size, the stirrer type, and the stirring speed. The best conditions, based on the product fineness and specific energy consumption of grinding, for the attrition grinding process is to grind the material with small grinding beads and a high rotational speed of the stirrer. Also, by using some suitable grinding additive, a finer product is achieved with a lower energy consumption. In jet mill grinding the most influential parameters were the feed rate, the volumetric flow rate of the grinding air, and the height of the internal classification tube. The optimised condition for the jet is to grind with a small feed rate and with a large rate of volumetric flow rate of grinding air when the inside tube is low. The finer product with a larger rate of production was achieved with the attrition bead mill than with the jet mill, thus the attrition grinding is better for the ultrafine grinding of gypsum than the jet grinding. Finally the suitability of the population balance model for simulation of grinding processes has been studied with different S , B , and C functions. A new S function for the modelling of an attrition mill and a new C function for the modelling of a jet mill were developed. The suitability of the selected models with the developed grinding functions was tested by curve fitting the particle size distributions of the grinding products and then comparing the fitted size distributions to the measured particle sizes. According to the simulation results, the models are suitable for the estimation and simulation of the studied grinding processes.
Resumo:
Information gained from the human genome project and improvements in compound synthesizing have increased the number of both therapeutic targets and potential lead compounds. This has evolved a need for better screening techniques to have a capacity to screen number of compound libraries against increasing amount of targets. Radioactivity based assays have been traditionally used in drug screening but the fluorescence based assays have become more popular in high throughput screening (HTS) as they avoid safety and waste problems confronted with radioactivity. In comparison to conventional fluorescence more sensitive detection is obtained with time-resolved luminescence which has increased the popularity of time-resolved fluorescence resonance energy transfer (TR-FRET) based assays. To simplify the current TR-FRET based assay concept the luminometric homogeneous single-label utilizing assay technique, Quenching Resonance Energy Transfer (QRET), was developed. The technique utilizes soluble quencher to quench non-specifically the signal of unbound fraction of lanthanide labeled ligand. One labeling procedure and fewer manipulation steps in the assay concept are saving resources. The QRET technique is suitable for both biochemical and cell-based assays as indicated in four studies:1) ligand screening study of β2 -adrenergic receptor (cell-based), 2) activation study of Gs-/Gi-protein coupled receptors by measuring intracellular concentration of cyclic adenosine monophosphate (cell-based), 3) activation study of G-protein coupled receptors by observing the binding of guanosine-5’-triphosphate (cell membranes), and 4) activation study of small GTP binding protein Ras (biochemical). Signal-to-background ratios were between 2.4 to 10 and coefficient of variation varied from 0.5 to 17% indicating their suitability to HTS use.
Resumo:
The aim of the work presented in this study was to demonstrate the wide applicability of a single-label quenching resonance energy transfer (QRET) assay based on time-resolved lanthanide luminescence. QRET technology is proximity dependent method utilizing weak and unspecific interaction between soluble quencher molecule and lanthanide chelate. The interaction between quencher and chelate is lost when the ligand binds to its target molecule. The properties of QRET technology are especially useful in high throughput screening (HTS) assays. At the beginning of this study, only end-point type QRET technology was available. To enable efficient study of enzymatic reactions, the QRET technology was further developed to enable measurement of reaction kinetics. This was performed using proteindeoxyribonuclei acid (DNA) interaction as a first tool to monitor reaction kinetics. Later, the QRET was used to study nucleotide exchange reaction kinetics and mutation induced effects to the small GTPase activity. Small GTPases act as a molecular switch shifting between active GTP bound and inactive GDP bound conformation. The possibility of monitoring reaction kinetics using the QRET technology was evaluated using two homogeneous assays: a direct growth factor detection assay and a nucleotide exchange monitoring assay with small GTPases. To complete the list, a heterogeneous assay for monitoring GTP hydrolysis using small GTPases, was developed. All these small GTPase assays could be performed using nanomolar protein concentrations without GTPase pretreatment. The results from these studies demonstrated that QRET technology can be used to monitor reaction kinetics and further enable the possibility to use the same method for screening.
Resumo:
Photosystem II (PSII) of oxygenic photosynthesis is susceptible to photoinhibition. Photoinhibition is defined as light induced damage resulting in turnover of the D1 protein subunit of the reaction center of PSII. Both visible and ultraviolet (UV) light cause photoinhibition. Photoinhibition induced by UV light damages the oxygen evolving complex (OEC) via absorption of UV photons by the Mn ion(s) of OEC. Under visible light, most of the earlier hypotheses assume that photoinhibition occurs when the rate of photon absorption by PSII antenna exceeds the use of the absorbed energy in photosynthesis. However, photoinhibition occurs at all light intensities with the same efficiency per photon. The aim of my thesis work was to build a model of photoinhibition that fits the experimental features of photoinhibition. I studied the role of electron transfer reactions of PSII in photoinhibition and found that changing the electron transfer rate had only minor influence on photoinhibition if light intensity was kept constant. Furthermore, quenching of antenna excitations protected less efficiently than it would protect if antenna chlorophylls were the only photoreceptors of photoinhibition. To identify photoreceptors of photoinhibition, I measured the action spectrum of photoinhibition. The action spectrum showed resemblance to the absorption spectra of Mn model compounds suggesting that the Mn cluster of OEC acts as a photoreceptor of photoinhibition under visible light, too. The role of Mn in photoinhibition was further supported by experiments showing that during photoinhibition OEC is damaged before electron transfer activity at the acceptor side of PSII is lost. Mn enzymes were found to be photosensitive under visible and UV light indicating that Mn-containing compounds, including OEC, are capable of functioning as photosensitizers both in visible and UV light. The experimental results above led to the Mn hypothesis of the mechanism of continuous-light-induced photoinhibition. According to the Mn hypothesis, excitation of Mn of OEC results in inhibition of electron donation from OEC to the oxidized primary donor P680+ both under UV and visible light. P680 is oxidized by photons absorbed by chlorophyll, and if not reduced by OEC, P680+ may cause harmful oxidation of other PSII components. Photoinhibition was also induced with intense laser pulses and it was found that the photoinhibitory efficiency increased in proportion to the square of pulse intensity suggesting that laser-pulse-induced photoinhibition is a two-photon reaction. I further developed the Mn hypothesis suggesting that the initial event in photoinhibition under both continuous and pulsed light is the same: Mn excitation that leads to the inhibition of electron donation from OEC to P680+. Under laser-pulse-illumination, another Mn-mediated inhibitory photoreaction occurs within the duration of the same pulse, whereas under continuous light, secondary damage is chlorophyll mediated. A mathematical model based on the Mn hypothesis was found to explain photoinhibition under continuous light, under flash illumination and under the combination of these two.
Resumo:
Sellun kuivatuksesta ei löydy paljoa tutkimustietoa. Työn tarkoituksena on antaa lyhyt teoriakuvaus sellun kuivatuksesta, kuivatukseen vaikuttavista tekijöistä jasellun kuivatuksen vaikutuksesta sellun laatuun. Käytännön osassa tutkittiin kuivauskoneen poikkiradan hienoainepitoisuuden ja vetolujuussuhteiden vaihtelua, suihkusuhteiden, kenkäpuristimen viivakuorman sekä paalipuristimen puristusvoimanvaikutusta sellun paperiteknisiin ominaisuuksiin. Sellun kuivauskone koostuu perälaatikosta, viiraosasta, puristinosasta sekä kuivausosasta.Perälaatikon tehtävä on syöttää massa tasaisesti viiraosalle. Viiraosalla poistuu suurin osa vedestä (noin 94 %) ja viiraosalla tapahtuu pohjan muodostus. Tässä työssä tutkittu suihkusuhde on yksi rainan muodostukseen vaikuttava tekijä. Puristinosalla voidaan sellun ominaisuuksiin vaikuttaa puristuksen voimalla ja kestolla ja tätä työssä tutkittiin kenkäpuristimen viivakuormaa muuttamalla. Varsinainen kuivatus voi tapahtua joko kuumia sylinteripintoja tai ilmaa hyödyntäen. Kuivauskoneen jälkeen on leikkuri, paalauspöytä ja paalipuristin. Paalipuristuksen vaikutusta sellun ominaisuuksiin tutkittiin keventämällä paalipuristusta nykyisestä.
Resumo:
Diplomityössä tutkitaan kolmea erilaista virtausongelmaa CFD-mallinnuksella. Yhteistä näille ongelmille on virtaavana aineena oleva ilma. Lisäksi tapausten perinteinen mittaus on erittäin vaikeaa tai mahdotonta. Ensimmäinen tutkimusongelma on tarrapaperirainan kuivain, jonka tuotantomäärä halutaan nostaa kaksinkertaiseksi. Tämä vaatii kuivatustehon kaksinkertaistamista, koska rainan viipymäaika kuivausalueella puolittuu. Laskentayhtälöillä ja CFD-mallinnuksella tutkitaan puhallussuihkun nopeuden ja lämpötilan muutoksien vaikutusta rainan pinnan lämmön- ja massansiirtokertoimiin. Tuloksena saadaan varioitujen suureiden sekä massan- ja lämmönsiirtokertoimien välille riippuvuuskäyrät, joiden perusteella kuivain voidaan säätää parhaallamahdollisella tavalla. Toinen ongelma käsittelee suunnitteilla olevan kuparikonvertterin sekundaarihuuvan sieppausasteen optimointia. Ilman parannustoimenpiteitä käännetyn konvertterin päästöistä suurin osa karkaa ohi sekundaarihuuvan. Tilannetta tutkitaan konvertterissa syntyvän konvektiivisen nostevirtauksen eli päästöpluumin sekä erilaisten puhallussuihkuratkaisujen CFD-mallinnuksella. Tuloksena saadaan puhallussuihkuilla päästöpluumia poikkeuttava ilmaverho. Suurin osa nousevasta päästöpluumista indusoituu ilmaverhoon ja kulkeutuu poistokanavaan. Kolmas tutkittava kohde on suunnitteilla oleva kuparielektrolyysihalli, jossa ilmanvaihtoperiaatteena on luonnollinen ilmanvaihto ja mekaaninen happosumun keräysjärjestelmä. Ilmanvaihtosysteemin tehokkuus ja sisäilman virtaukset halutaan selvittää ennen hallin rakentamista. CFD-mallinnuksella ja laskentayhtälöillä tutkitaan lämpötila- ja virtauskentät sekä hallin läpi virtaava ilmamäärä ja ilmanvaihtoaste. Tulo- ja poistoilma-aukkojen mitoitukseen ja sijoitukseen liittyvät suunnitteluarvot varmennetaan sekä löydetään ilmanvaihdon ongelmakohdat. Ongelmakohtia tutkitaan ja niille esitetään parannusehdotukset.
Resumo:
Tämän diplomityön tavoitteena oli saada perustietoa tekijöistä, jotka vaikuttavat musteen kuivumiseen erilaisilla paperipinnoilla inkjet tulostuksessa. Tavoitteena oli saada tietoa erilaisista musteista, joita käytetään yleisimmissä inkjet tulostustekniikoissa, miten paperit vaikuttavat musteen kuivumiseen ja minkälaisia menetelmiä on olemassa musteen kuivumistekijöiden määrittämiseen. Lisäksi tarkoituksena oli varmistaa, voidaanko inkjetmusteiden absorptioajan määrittämiseen käytettävää DIGAT-laitetta käyttää määrittämään ja ennustamaan erilaisten musteiden kuivumista erilaisilla paperipinnoilla sekä etsiä korrelaatioita musteen absorptioajan ja teknisten paperiominaisuuksien sekä inkjet tulostuksen laadun välillä. Kirjallisuusosassa tarkasteltiin erilaisia inkjet tulostusmenetelmiä, niissä käytettäviä musteita ja musteiden koostumuksia. Tutkittiin myös paperin ja musteen välisiä vuorovaikutuksia sekä inkjet tulostuksen laatua. Kokeellisessa osassa tutkittiin musteenabsorboitumista paperiin DIGAT-laitteen avulla. kuudella eri musteella. Paperinäytteistä määritettiin teknisiä paperiominaisuuksia sekä ominaisuuksia, jotka liittyvät inkjet tulostuksen laatuun. Inkjet tulostuksen laatua tarkasteltiin tulostamalla testikuva kolmella eri tulostimella, jotka olivat Canon Bubble Jet i950, HP DeskJet Cxi970 ja Epson Stylus C46. Havaittiin, että DIGAT-laite ei sovellu määrittämään musteen absorptioaikoja kiiltäville näytteille.Tässä tutkimuksessa näyte, jonka kiilto oli 65 %, oli liian kiiltävä mitattavaksi DIGAT-laitteella. Lisäksi absorptiomäärityksissä havaittiin, että erilaiset musteet asettuvat erilailla paperin pintaan ja että pigmenttipohjaisella musteella asettumisaika oli kaikista pisin. Musteiden absorptioajat olivat nopeimpia erikoisinkjetpaperilla ja hitaimpia päällystetyillä, tiiviillä papereilla. Musteen absorptioajan ja teknisten paperiominaisuuksien ja inkjet tulostuksen laadun välisiä korrelaatioita oli vaikea havaita. Voidaan sanoa, että tulokset olivat muste- ja printterikohtaisia. Havaittiin vain muutamia teknisiä paperiominaisuuksia, jotka korreloivat hyvin musteen absorboitumisen kanssa. Nämäolivat Gurley-Hill huokoisuus, paperin tuhka- sekä kalsiumkarbonaattipitoisuus ja K&N värinabsorptio. Myöskään inkjet tulostuksen laadun ja musteen absorption välisiä korrelaatioita ei löytynyt kuin muutama; densiteetti, mottling sekä bleeding. Tämän tutkimuksen perusteella voidaan todeta DIGAT-laitteen soveltuvan hyvin kuvaamaan inkjet tulostuksen laatuominaisuuksista densiteettia, mottlingia sekä bleedingiä. DIGAT-laitetta voidaan siis käyttää avuksi ennustettaessa kuivumisaikaa ja sen vaikutusta edellä mainittuihin ominaisuuksiin. Läpipainatusominaisuuksia DIGAT-laitteen avulla ei voida tutkia, sillä ne ovat enemmän riippuvaisia paperin neliömassasta, paksuudesta ja huokoisuudesta kuinmusteen absorptioajasta. Teknisistä paperiominaisuuksista Gurley-Hill huokoisuus, paperin tuhka-sekä CaCO3-pitoisuus ja K&N värinabsorptio kuvaavat hyvin musteen imeytymisaikaa paperiin, kun taas ominaisuudet Cobb, HST ja polaari- sekädispersiokomponentit eivät kuvaa. Näyttää siltä, että testikuva, joka on tällä hetkellä käytössä UPM Tutkimus-keskuksessa, ei sovellu suurtehotulostuksen laadun tarkkailuun. Testikuva toimii hyvin pöytätulostimilla ja perinteisillä kopiopapereilla ja inkjetpapereilla, jotka on tarkoitettu tulostettaviksi hitaasti. Tulostusnopeuden ja musteen kuivumisnopeuden välisiä ilmiöitä seei tuo esille, joten se ei sovellu kuvaamaan suurtehotulostusta.
Resumo:
Huoneen sisäisten lämpölähteiden aiheuttamilla konvektiovirtauksilla eli pluumeilla on huomattava vaikutus ilmastointipalkkijärjestelmäntoimintaan. Tätä vaikutusta ei ole tutkittu kovin paljon. Tässä työssä tutkittiin huoneen päätyseinässä olevan sähkölämmityspatterin vaikutusta aktiivisen ilmastointipalkin toimintaan. Tutkimus kohdistui vastakkaisten suihkujen törmäykseen. Suihkuina olivat pluumit ja tuloilmavirtaus. Tutkimukseen kuului sekä teoreettinen että kokeellinen osio. Teoreettisessa tarkastelussa käytiin läpi ilmastointipalkin teoriaa sekä konvektiovirtausten muodostumisen teoriaa. Lisäksi esitettiin, kuinka suihkuista lasketaan liikemäärävirta. Kokeellisessa osiossa mitattiin huoneen sisäisten lämpölähteiden aiheuttamia pluumeja. Lämpölähteet oli sijoitettuina tutkimushuoneen päätyseinän viereen. Mittauksissa keskityttiin tarkemmin sähkölämmityspatteriin ja sitä mallinnettiin eri tehoilla. Lisäksi mitattiin ilmastointipalkin tuloilmavirtausta eri ilmamäärillä. Pluumien ja tuloilmavirtauksen törmäyskäyttäytymistä selvitettiin savukuvauksella. Analyysiosiossa sähkölämmityspatterin aiheuttaman pluumin ja palkin tuloilmavirtauksen törmäyskäyttäytymiselle kehitettiin malli. Mallissa huomioitiin vastaikkaisten törmäävien suihkujen liikemäärät ja esitettiin kohdat tutkimushuoneen pituussuunnassa, jossa tuloilmavirtaus kääntyy oleskeluvyöhykkeelle. Ilmastointipalkkijärjestelmässä tuloilmavirtauksen tulisi kääntyä oleskeluvyöhykkeelle vasta huoneen seinustalla. Tutkimuksen perusteella näin käy, jos pluumin liikemäärä on noin 10% tai vähemmän tuloilman liikemäärästä. Muulloin palkin tuloilmavirtaus kääntyy oleskeluvyöhykkeelle liian aikaisin ja aiheuttaa mahdollisestivedontunnetta.
Resumo:
Laboratoriomittakaavainen formeri on välttämätön, jotta paperinvalmistusprosessin jäljitteleminen olisi mahdollista. Vaikka erilaisia formereita löytyykin paperiteollisuudesta, tilaa on kuitenkin laboratoriomittakaavaiselle paperinvalmistusmenetelmälle, joka sijoittuisipilottikoneen ja perinteisen laboratorioarkkimuotin välille. Formeri, jolla saadaan aikaiseksi oikean paperinvalmistuksen kaltaiset olosuhteet ja ilmiöt on kehitetty, ja sen toiminta on testattu Nalcon Papermaking Centreof Excellence:ssä Espoossa. Formeri on yhdistetty Nalcon lähestymisjärjetelmäsimulaattoriin ja simulaattorilla aikaansaadut hydro-kemialliset ilmiöt voidaan testata nyt myös arkeista. Laitteessa on perälaatikko ja viiraosa. Perälaatikosta massa virtaa viiralle, joka liikkuu eteenpäin hihnakuljettimen hihnojen päällä. Suihku-viira -suhdetta voidaan muuttaa joko muuttamalla virtausnopeutta tai viiran nopeutta tai säätämällä perälaatikon huuliaukkoa. Formerintoiminnan testaus osoitti, että se toimii teknisesti hyvin ja tulokset ovat toistettavia ja loogisia. Arkeissa kuidut ovat orientoituneet, formaatio ja vetolujuussuhde KS/PS riippuvat voimakkaasti suihku-viira -suhteesta, kuten oikeillakinpaperikoneilla.
Resumo:
Alkyl ketene dimers (AKD) are effective and highly hydrophobic sizing agents for the internal sizing of alkaline papers, but in some cases they may form deposits on paper machines and copiers. In addition, alkenyl succinic anhydrides (ASA)- based sizing agents are highly reactive, producing on-machine sizing, but under uncontrolled wet end conditions the hydrolysis of ASA may cause problems. This thesis aims at developing an improved ketene dimer based sizing agent that would have a lower deposit formation tendency on paper machines and copiers than a traditional type of AKD. The aim is also to improve the ink jet printability of a AKD sized paper. The sizing characteristics ofketene dimers have been compared to those of ASA. A lower tendency of ketene dimer deposit formation was shown in paper machine trials and in printability tests when branched fatty acids were used in the manufacture of a ketene dimer basedsizing agent. Fitting the melting and solidification temperature of a ketene dimer size to the process temperature of a paper machine or a copier contributes to machine cleanliness. A lower hydrophobicity of the paper sized with branched ketene dimer compared to the paper sized with traditional AKD was discovered. However, the ink jet print quality could be improved by the use of a branched ketene dimer. The branched ketene dimer helps in balancing the paper hydrophobicity for both black and color printing. The use of a high amount of protective colloidin the emulsification was considered to be useful for the sizing performance ofthe liquid type of sizing agents. Similar findings were indicated for both the branched ketene dimer and ASA.
Resumo:
Diplomityön tavoitteena oli tutkia selluradan leijutusta sekä hallintaa kapealla ja täysleveällä selluradalla ilmakuivaimessa. Työn sisältö on jaettu neljään osaan teoriaan, numeeriseen virtauslaskentaan, kokeelliseen osuuteen ja johtopäätöksiin. Työn alussa kiinnitettiin huomiota ilmakuivaimen ja selluradan rakenteeseen, selluradan lujuusominaisuuksiin ja niiden testaamiseen laboratorio-oloissa. Teoria osuudessa tarkasteltiin selluradan leijutusteoriaa ja siihen liittyvää virtaustekniikkaa. Leijutusta kuvattiin mekaniikasta tutun vapaakappalekuvan muodossa. Vapaakappalekuva auttaa ymmärtämään sellurataan vaikuttavia voimia ja niiden aiheuttajia. Numeerisessa virtauslaskennassa rakennettiin Fluent -virtauslaskentamalli. Malli kuvaa leijutussuuttimen alusta 0,2 metrin pituista pätkää. Laskennassa simuloitiin selluradan lei-jutusta 2, 5 ja 7 mm etäisyyksillä. Tuloksia tarkasteltiin paine- ja nopeusjakaumien muodossa. Kokeellisessa osuudessa tehtiin mittauksia yksittäisellä ylä- ja alasuuttimella sekä suutinpaketilla. Yksittäisistä suuttimista mitattiin ilmasuihkujen ulostulokulmaa, suuttimensisäistä painejakaumaa ja selluradan pintaan vaikuttavaa staattista painetta suuttimen pituuden funktiona. Suutinpaketilla tutkittiin ilmasuihkujen ja tasomaisen levyn välistä vuorovaikutusta. Ylä- ja alasuuttimen välissä leijutettiin levyä, josta mitattiin ilmasuihkujen aiheuttama z-suuntainen voima ja leijutuskorkeus. Työn lopussa arvioitiin teorian, numeerisen virtauslaskennan ja kokeellisen osuuden tuloksia. Näiden pohjalta tehtiin teknisiä parannusehdotuksia ilmakuivaimen toiminnan tehostamiseksi ja selluradan hallinnan parantamiseksi kapealla ja täysleveällä selluradalla.