Dynamic analysis of belt-drives using the absolute nodal coordinate formulation

Belt-drive systems have been and still are the most commonly used power transmission form in various applications of different scale and use. The peculiar features of the dynamics of the belt-drives include highly nonlinear deformation,large rigid body motion, a dynamical contact through a dry friction interface between the belt and pulleys with sticking and slipping zones, cyclic tension of the belt during the operation and creeping of the belt against the pulleys. The life of the belt-drive is critically related on these features, and therefore, amodel which can be used to study the correlations between the initial values and the responses of the belt-drives is a valuable source of information for the development process of the belt-drives. Traditionally, the finite element models of the belt-drives consist of a large number of elements thatmay lead to computational inefficiency. In this research, the beneficial features of the absolute nodal coordinate formulation are utilized in the modeling of the belt-drives in order to fulfill the following requirements for the successful and efficient analysis of the belt-drive systems: the exact modeling of the rigid body inertia during an arbitrary rigid body motion, the consideration of theeffect of the shear deformation, the exact description of the highly nonlinear deformations and a simple and realistic description of the contact. The use of distributed contact forces and high order beam and plate elements based on the absolute nodal coordinate formulation are applied to the modeling of the belt-drives in two- and three-dimensional cases. According to the numerical results, a realistic behavior of the belt-drives can be obtained with a significantly smaller number of elements and degrees of freedom in comparison to the previously published finite element models of belt-drives. The results of theexamples demonstrate the functionality and suitability of the absolute nodal coordinate formulation for the computationally efficient and realistic modeling ofbelt-drives. This study also introduces an approach to avoid the problems related to the use of the continuum mechanics approach in the definition of elastic forces on the absolute nodal coordinate formulation. This approach is applied to a new computationally efficient two-dimensional shear deformable beam element based on the absolute nodal coordinate formulation. The proposed beam element uses a linear displacement field neglecting higher-order terms and a reduced number of nodal coordinates, which leads to fewer degrees of freedom in a finite element.

Simulating the performance of paper machine control

The topic of this thesis is the simulation of a combination of several control and data assimilation methods, meant to be used for controlling the quality of paper in a paper machine. Paper making is a very complex process and the information obtained from the web is sparse. A paper web scanner can only measure a zig zag path on the web. An assimilation method is needed to process estimates for Machine Direction (MD) and Cross Direction (CD) profiles of the web. Quality control is based on these measurements. There is an increasing need for intelligent methods to assist in data assimilation. The target of this thesis is to study how such intelligent assimilation methods are affecting paper web quality. This work is based on a paper web simulator, which has been developed in the TEKES funded MASI NoTes project. The simulator is a valuable tool in comparing different assimilation methods. The thesis contains the comparison of four different assimilation methods. These data assimilation methods are a first order Bayesian model estimator, an ARMA model based on a higher order Bayesian estimator, a Fourier transform based Kalman filter estimator and a simple block estimator. The last one can be considered to be close to current operational methods. From these methods Bayesian, ARMA and Kalman all seem to have advantages over the commercial one. The Kalman and ARMA estimators seems to be best in overall performance.

Development of finite elements for analysis of biomechanical structures using flexible multibody formulations

The absolute nodal coordinate formulation was originally developed for the analysis of structures undergoing large rotations and deformations. This dissertation proposes several enhancements to the absolute nodal coordinate formulation based finite beam and plate elements. The main scientific contribution of this thesis relies on the development of elements based on the absolute nodal coordinate formulation that do not suffer from commonly known numerical locking phenomena. These elements can be used in the future in a number of practical applications, for example, analysis of biomechanical soft tissues. This study presents several higher-order Euler–Bernoulli beam elements, a simple method to alleviate Poisson’s and transverse shear locking in gradient deficient plate elements, and a nearly locking free gradient deficient plate element. The absolute nodal coordinate formulation based gradient deficient plate elements developed in this dissertation describe most of the common numerical locking phenomena encountered in the formulation of a continuum mechanics based description of elastic energy. Thus, with these fairly straightforwardly formulated elements that are comprised only of the position and transverse direction gradient degrees of freedom, the pathologies and remedies for the numerical locking phenomena are presented in a clear and understandable manner. The analysis of the Euler–Bernoulli beam elements developed in this study show that the choice of higher gradient degrees of freedom as nodal degrees of freedom leads to a smoother strain field. This improves the rate of convergence.

Why are some companies more successful than others? An exploration into organizational culture and dynamic capabilities

Why are some companies more successful than others? This thesis approaches the question by enlisting theoretical frameworks that explain the performance with internal factors, deriving from the resource-based view, namely the dynamic capabilities approach. To deepen the understanding of the drivers and barriers towards developing these higher order routines aiming at improving the operational level routines, this thesis explores the organisational culture and identity research for the microfoundational antecedents that might shed light on the formation of the dynamic capabilities. The dynamic capabilities framework in this thesis strives to take the theoretical concept closer to practical applicability. This is achieved through creation of a dynamic capabilities matrix, consisting of four dimensions often encountered in dynamic capabilities literature. The quadrants are formed along internal-external and resources-abilities axes, and consist of Sensing, Learning, Reconfiguration and Partnering facets. A key element of this thesis is the reality continuum, which illustrates the different levels of reality inherent in any entity of human individuals. The theoretical framework constructed in the thesis suggests a link between the collective but constructivist understanding of the organisation and both the operational and higher level routines, evident in the more positivist realm. The findings from three different case organisations suggest that the constructivist assumptions inherent to an organisation function as a generative base for both drivers and barriers towards developing dynamic capabilities. From each organisation one core assumption is scrutinized to identify its connections to the four dimensions of the dynamic capabilities. These connections take the form of drivers or barriers – or have the possibility to develop into one or the other. The main contribution of this thesis is to show that one key for an organisation to perform well in a turbulent setting, is to understand the different levels of realities inherent in any group of people. Recognising the intangible levels gives an advantage in the tangible ones.

Use of the Optical Cantilever Microphone in Photoacoustic Spectroscopy

A novel cantilever pressure sensor was developed in the Department of Physics at the University of Turku in order to solve the sensitivity problems which are encountered when condenser microphones are used in photoacoustic spectroscopy. The cantilever pressure sensor, combined with a laser interferometer for the measurement of the cantilever movements, proved to be highly sensitive. The original aim of this work was to integrate the sensor in a photoacoustic gas detector working in a differential measurement scheme. The integration was made successfully into three prototypes. In addition, the cantilever was also integrated in the photoacoustic FTIR measurement schemes of gas-, liquid-, and solid-phase samples. A theoretical model for the signal generation in each measurement scheme was created and the optimal celldesign discussed. The sensitivity and selectivity of the differential method were evaluated when a blackbody radiator and a mechanical chopper were used with CO₂, CH4, CO, and C2H4 gases. The detection limits were in the sub-ppm level for all four gases with only a 1.3 second integration time and the cross interference was well below one percent for all gas combinations other than those between hydrocarbons. Sensitivity with other infrared sources was compared using ethylene as an example gas. In the comparison of sensitivity with different infrared sources the electrically modulated blackbody radiator gave a 35 times higher and the CO2-laser a 100 times lower detection limit than the blackbody radiator with a mechanical chopper. As a conclusion, the differential system is well suited to rapid single gas measurements. Gas-phase photoacoustic FTIR spectroscopy gives the best performance, when several components have to be analyzed simultaneously from multicomponent samples. Multicomponent measurements were demonstrated with a sample that contained different concentrations of CO₂, H₂O, CO, and four different hydrocarbons. It required an approximately 10 times longer measurement time to achieve the same detection limit for a single gas as with the differential system. The properties of the photoacoustic FTIR spectroscopy were also compared to conventional transmission FTIR spectroscopy by simulations. Solid- and liquid-phase photoacoustic FTIR spectroscopy has several advantages compared to other techniques and therefore it also has a great variety of applications. A comparison of the signal-to-noise ratio between photoacoustic cells with a cantilever microphone and a condenser microphone was done with standard carbon black, polyethene, and sunflower oil samples. The cell with the cantilever microphone proved to have a 5-10 times higher signal-to-noise ratio than the reference detector, depending on the sample. Cantilever enhanced photoacoustics will be an effective tool for gas detection and analysis of solid- and liquid-phase samples. The preliminary prototypes gave good results in all three measurement schemes that were studied. According to simulations, there are possibilities for further enhancement of the sensitivity, as well as other properties, of each system.

Metsäsääntely Suomessa ja Venäjällä. Näkökulmia kestävään metsätalouteen

Sustainability is the aim of forest management and forest regulation in many countries. Accordingly, forest management has been steered towards more environmentally friendly methods and new regulatory instruments have been introduced. At the same time, wood trade and forest industry have become a global business. Even if the importance of national forest legislation has not decreased, it has been widely acknowledged that national regulation of forest management is no longer sufficient. The movement of goods does not acknowledge boundaries, even though most negative environmental and social consequences stay in the country of origin of wood and other raw materials. As a partial solution to this dilemma, different kinds of regulations have been developed. Various forest certification schemes and wood trade regulation in the EU (995/2010) are examples of efforts to prevent illegal logging and unsustainable forestry. The Finland-based forest industry is to a varying extent dependent on wood trade from Russia. Especially in the 1990‟s, ethical questions concerning import of wood from Russian old growth forests near the Finnish border were widely discussed. Consequently, forest industry enterprises have developed systems to trace the origin of wood and to buy certified wood from Russia. The aim of the research has been to evaluate Finnish and Russian forest regulations in order to investigate what kind of forest management these regulations enhance, and to what extent ecologically sustainable forest management has been integrated into different forms of regulation. I have examined Finnish and Russian forest regulation in four separate articles based on the topics of the Russian Forest Code, forest certification and other voluntary forest protection measures in Russia, Finnish forest certification and Finnish forest legislation. One objective has been to analyse the roles voluntary forest certification plays in promoting sustainable forest management in different countries. In my research, I have mainly concentrated on ecological sustainability and protection of biodiversity, although other aspects of sustainable forest management have been touched upon in different articles. In the following I shall conclude the findings of my research. When the current Russian Forest Code (2006) was being adopted, the main emphasis was not on ecological issues, but on reorganizing forest governance. The role of ecological requirements was even slightly diminished during the legislative reform. There are, nevertheless, still stipulations aiming at ecological sustainability, such as the division of forests into different forest management categories and various protection zones. In 2000, FSC forest certification arrived in Russia, at present covering already 28 million hectares of forests. The PEFC scheme is now in use as well, but to a much lesser extent. If properly implemented, Russian forest certification schemes clearly improve the level of ecological and social sustainability of forestry in Russia. Certification criteria, however, are partly in conflict with the Russian forest legislation and certified enterprises have been forced to pay fines or to negotiate with forest authorities. This clearly indicates that even if Russian forest legislation has otherwise been liberalized to a certain extent, some significant paternalism still exists. Voluntary, hands-on biodiversity protection measures are not valued, and they are not part of the official protection policies as in many other countries. However, there have been some regional solutions to this dilemma. In the Republic of Karelia forest authorities have approved a set of forest biodiversity protection rules created by a local NGO and a forest industry enterprise. By following these local rules, an enterprise can avoid fines for protection measures. The current Finnish Forest Act was adopted in 1996. It brought forest legislation into a new era as some ecological aspects were integrated into forest legislation. The various soft-law forest management recommendations further increased the level of biodiversity protection. My evaluation of the overall legitimacy of the Finnish forest legislation and forest management paradigm revealed, however, several problematic issues. As part of this study I analysed the history of the current forest management paradigm. This analysis revealed the path dependency which still hinders the protection of biodiversity and clearly decreases the general legitimacy of forest management. Due to several historical reasons only even-structured forest management based on clear cuts has for decades been officially approved in Finland. Due to increasing demands of forest owners the legislation is finally being revised. Yet, the official approval of uneven-structured forest management would not be enough to fully improve ecological, social and cultural legitimacy. The latest ecological theories and knowledge of endangered species should be taken into account in the on-going reform of forest legislation as well as the modernisation. Forest legislation is one of the very few spheres of Finnish environmental legislation where openness and participation are still considered a threat. The first Finnish forest certification scheme, PEFC, was established in 2000. It now covers more than 20 million hectares, about 95% of the forests in Finland. PEFC Finland does not require a higher level of biodiversity protection than the recommendations by Tapio (the Development Centre for Forestry), but certification has unified forest management practices and requires more protection measures than mere forest legislation. The study suggests that in Finland PEFC has not functioned as an instrument which would substantially improve the level of forest management. Rather it has supported the status quo of the forest sector. While the ecological and social responsibility of Finland-based forest corporations was one impetus for this research, I want to conclude that there are problems related to forest legislation and non-state regulation in both Finland and Russia. If an enterprise buying wood from Russia buys only certified wood, and carefully avoids wood coming from high conservation value forests that are either ecologically or socially valuable, it can be claimed to be as sustainably produced as in Finland. However, there must be continuous scrutiny of the circumstances. In Russia, the level of the compliance of certification criteria varies considerably, and there are vast unprotected invaluable forest areas. The utilisation of these areas should not be based on short-sighted decisions or lack of consensus among stakeholders.

eWOM communication in social media: A study of its antecedents in higher education context

The aim of this master’s thesis was to examine antecedents of eWOM communication in social media in the higher education context. In order to achieve this goal, eWOM communications of the students’ of international master’s programmes at Lappeenranta University of Technology were studied. The main research question was formulated as follows: What kind of effect do service-, brand-related antecedents, contextual antecedents and moderating factors have on LUT’s international master’s degree students’ eWOM communication in social media regarding their studies? The theory part of the master’s thesis was focused on the discussion of service- and brand related eWOM antecedents, contextual antecedents, as well as moderating relationships between them. The empirical part of the master’s thesis was based on quantitative research method. A web-based survey was carried out among current students of international master’s degree programmes at LUT. Out of 712 e-mail invitations sent, 159 responses were received in total. Thus, response rate was 22%. The results of the study showed that satisfaction, commitment, virtual brand community commitment, need for an advice, positive altruistic concerns, negative altruistic concerns, and attitude towards eWOM communications have an effect on eWOM in higher education context. Several moderating effects on eWOM were determined in the present study as well. On the other hand, it was found that dissatisfaction, loyalty, brand identification, desire to help the organization, need for positive self-enhancement, and social risk perception do not have an effect on eWOM in higher education context.