Effect of Mechanical and Geometric Mismatching on Fatigue and Damage of Welded Joints

The future of high technology welded constructions will be characterised by higher strength materials and improved weld quality with respect to fatigue resistance. The expected implementation of high quality high strength steel welds will require that more attention be given to the issues of crack initiation and mechanical mismatching. Experiments and finite element analyses were performed within the framework of continuum damage mechanics to investigate the effect of mismatching of welded joints on void nucleation and coalescence during monotonic loading. It was found that the damage of undermatched joints mainly occurred in the sandwich layer and the damageresistance of the joints decreases with the decrease of the sandwich layer width. The damage of over-matched joints mainly occurred in the base metal adjacent to the sandwich layer and the damage resistance of the joints increases with thedecrease of the sandwich layer width. The mechanisms of the initiation of the micro voids/cracks were found to be cracking of the inclusions or the embrittled second phase, and the debonding of the inclusions from the matrix. Experimental fatigue crack growth rate testing showed that the fatigue life of under-matched central crack panel specimens is longer than that of over-matched and even-matched specimens. Further investigation by the elastic-plastic finite element analysis indicated that fatigue crack closure, which originated from the inhomogeneousyielding adjacent to the crack tip, played an important role in the fatigue crack propagation. The applicability of the J integral concept to the mismatched specimens with crack extension under cyclic loading was assessed. The concept of fatigue class used by the International Institute of Welding was introduced in the parametric numerical analysis of several welded joints. The effect of weld geometry and load condition on fatigue strength of ferrite-pearlite steel joints was systematically evaluated based on linear elastic fracture mechanics. Joint types included lap joints, angle joints and butt joints. Various combinations of the tensile and bending loads were considered during the evaluation with the emphasis focused on the existence of both root and toe cracks. For a lap joint with asmall lack-of-penetration, a reasonably large weld leg and smaller flank angle were recommended for engineering practice in order to achieve higher fatigue strength. It was found that the fatigue strength of the angle joint depended strongly on the location and orientation of the preexisting crack-like welding defects, even if the joint was welded with full penetration. It is commonly believed that the double sided butt welds can have significantly higher fatigue strength than that of a single sided welds, but fatigue crack initiation and propagation can originate from the weld root if the welding procedure results in a partial penetration. It is clearly shown that the fatigue strength of the butt joint could be improved remarkably by ensuring full penetration. Nevertheless, increasing the fatigue strength of a butt joint by increasing the size of the weld is an uneconomical alternative.

Application of morphometry, static DNA ploidy analysis, and steroid receptor expression in diagnosis and prognosis of Libyan breast cancer

The aim of this study was to describe the demographic, clinicopathological, biological and morphometric features of Libyan breast cancer patients. The supporting value of nuclear morphometry and static image cytometry in the sensitivity for detecting breast cancer in conventional fine-needle aspiration biopsies were estimated. The findings were compared with findings in breast cancer in Finland and Nigeria. In addation, the value of ER and PR were evaluated. There were 131 histological samples, 41 cytological samples, and demographic and clinicopathological data from 234 Libyan patients. The Libyan breast cancer is dominantly premenopausal and in this feature it is similar to breast cancer in sub-Saharan Africans, but clearly different from breast cancer in Europeans, whose cancers are dominantly postmenopausal in character. At presention most Libyan patients have locally advanced disease, which is associated with poor survival rates. Nuclear morphometry and image DNA cytometry agree with earlier published data in the Finnish population and indicate that nuclear size and DNA analysis of nuclear content can be used to increase the cytological sensitivity and specificity in doubtful breast lesions, particularly when free cell sampling method is used. Combination of the morphometric data with earlier free cell data gave the following diagnostic guidelines: Range of overlap in free cell samples: 55 μm2 -71 μm2. Cut-off values for diagnostic purposes: Mean nuclear area (MNA) >54 μm2 for 100% detection of malignant cases (specificity 84 %), MNA < 72 μm2 for 100% detection of benign cases (sensitivity 91%). Histomorphometry showed a significant correlation between the MNA and most clinicopathological features, with the strongest association observed for histological grade (p <0.0001). MNA seems to be a prognosticator in Libyan breast cancer (Pearson’s test r = - 0.29, p = 0.019), but at lower level of significance than in the European material. A corresponding relationship was not found in shape-related morphometric features. ER and PR staining scores were in correlation with the clinical stage (p= 0.017, and 0.015, respectively), and also associated with lymph node negative patients (p=0.03, p=0.05, respectively). Receptor-positive (HR+) patients had a better survival. The fraction of HR+ cases among Libyan breast cancers is about the same as the fraction of positive cases in European breast cancer. The study suggests that also weak staining (corresponding to as few as 1% positive cells) has prognostic value. The prognostic significance may be associated with the practice to use antihormonal therapy in HR+ cases. The low survival and advanced presentation is associated with active cell proliferation, atypical nuclear morphology and aneuploid nuclear DNA content in Libyan breast cancer patients. The findings support the idea that breast cancer is not one type of disease, but should probably be classified into premenopausal and post menopausal types.

Nuclear morphometry, apoptotic and mitotic indices, and tubular differentiation in Libyan breast cancer

Aims of this study were to evaluate the relations of nuclear morphometry, mitotic and apoptotic indices, and tubular differentiation with clinicopathological features and survival rate in Libyan women. The data were compared with corresponding results on Finnish, and Nigerian female breast cancer patients. Histological samples of breast cancer (BC) from 131 patients were retrospectively studied. Mitotic activity indices (MAI and SMI), apoptotic index (AI), and fraction of fields with tubular differentiation (FTD) were estimated. Samples were also studied by computerized nuclear morphometry, such as mean nuclear area (MNA). Demographic and clinicopathological features were analyzed from 234 patients. The Libyan BC was dominantly premenopausal, and aggressive in behavior. There were statistically significant correlations between the mean nuclear area, fraction of fields with tubular differentiation, apoptotic index and proliferative indices, and most clinicopathological features. The highest significances were shown between lymph node status and the proliferative and apoptotic indices (p=0.003 with SMI, and p=0.005 with AI). There were significant associations between clinical stage and SMI and AI (p=0.002 and 0.009, respectively). The most significant associations with grade were observed with MNA and FTD (p<0.0001 and 0.001, respectively). The proliferative differences between Libyan, Nigerian and Finnish populations were prominent. These indices in Libyan were lower than in Nigerian, but higher than in Finnish patients. The Libyan patients’ AI is slightly higher than in Nigeria, but much higher than in Finland. The differences between countries may be associated with the known variation in the distribution of genetic markers in these populations. The results also indicated that morphometric factors can be reliable prognostic indicators in Libyan BC patients.

Statistical variation of weld profiles and their expected influence on fatigue strength

The general objective of this study was to conduct astatistical analysis on the variation of the weld profiles and their influence on the fatigue strength of the joint. Weld quality with respect to its fatigue strength is of importance which is the main concept behind this thesis. The intention of this study was to establish the influence of weld geometric parameters on the weld quality and fatigue strength. The effect of local geometrical variations of non-load carrying cruciform fillet welded joint under tensile loading wasstudied in this thesis work. Linear Elastic Fracture Mechanics was used to calculate fatigue strength of the cruciform fillet welded joints in as-welded condition and under cyclic tensile loading, for a range of weld geometries. With extreme value statistical analysis and LEFM, an attempt was made to relate the variation of the cruciform weld profiles such as weld angle and weld toe radius to respective FAT classes.

Kosketukseton hitsin pintageometrian määrittäminen

Yleisesti tiedetään hitsin pintageometrian vaikuttavan rakenteen väsymislujuuteen. Nopean, edullisen ja luotettavan pintageometrian mittausmenetelmän kehittäminen on askel kohti tarkempaa ja varmempaa rakenteen väsymislujuuden tarkastelua. Tässä työssä on tutkittu hitsejä, joiden pinnan geometria on mitattu norjalaisen SINTEF -yrityksen kehittämällä rakenteellisen valon menetelmällä. Osana työtä kehitettiin MatLab -pohjainen ohjelma, jolla jälkikäsitellään mittauksesta saadut x-y-z -mittapisteet. Mittausdatan jälkikäsittelyssä saadaan mittauksesta määritettyähitsin reunan pyöristys, liittymäkulma, a-mitta, reunahaava ja kateettisuhde. Kehitettyä menetelmää käyttämällä mitattiin lähes 300 voimaakantamatontaristiliitoksen hitsiä. Mittaustuloksia verrattiin vastaavista kappaleista tehtyihin hiemittauksiin. Manuaalisen hieestä tehdyn mittauksen havaittiin olevan tarkempi ja pystyttiin havaitsemaan paikallisempia muotoja. Rakenteellisen valon mittauksissa tapahtunut heijastelu saatiin pienenemään käsittelemällä mitattava pinta mattavalkoisella maalilla. Rakenteellisen valon mittatarkkuudeksi saatiin noin 0,2 mm. Pohjautuen mitattuun hitsin reunan pyöristykseen ja liittymäkulmaan voidaan yksinkertaista kaavaa käyttämällä laskea hitsin jännityskonsentraatio ja näin saada alkuarvaus väsymislujuudelle. Myös muiden tekijöiden tiedetään vaikuttavan hitsin väsymislujuuteen, joten pyöristyksen ja liittymäkulman avulla tehdyt arviot eivät ole absoluuttisen oikeita. Tämä havaittiin väsytyskokeilla, joista yhdessä väsymisvaurio ei syntynyt suurimmankaan jännityskonsentraation alueella.