Tunkeuman hallinta MIG/MAG-hitsauksessa

MIG/MAG-hitsaukselle tyypillinen ominaispiirre, valokaaren itsesäätyvyys, saavutetaan vakiojännitelähdettä käyttämällä. Valokaaren sisäisen säätömekanismin ansiosta kaarenpituus pysyy vakiona, vaikka hitsauspolttimen ja työkappaleen välinen etäisyys vaihtelisi hitsauksen aikana. Vakiojännitelähteen käyttäminen aiheuttaa kuitenkin kaaritehon vaihtelua vapaalankapituuden muuttuessa. Vapaalangan kasvaessa liian pitkäksi kaariteho laskee niin alas, ettei se enää riitä sulattamaan tarpeeksi perusainetta railon kyljissä. Tämän seurauksena hitsausliitokseen syntyy erilaisia liittymävirheitä. Käsinhitsauksessa vapaalangan pituus saattaa polttimen epävakaasta kuljetuksesta johtuen vaihdella erityisesti kokemattomilla hitsaajilla. Mekanisoidussa ja automatisoidussa hitsauksessa railojen mitta- ja muotopoikkeamat aiheuttavat vapaalankapituuden vaihtelua. Poikkeamia syntyy kaikissa hitsausrailojen esivalmistusvaiheissa. Lisäksi lämmöntuonnin aiheuttamat muodonmuutokset kappaleissa lisäävät poikkeamia railonsovituksessa hitsauksen aikana. Ongelma on useimmiten ratkaistavissa railonseurantaa käyttämällä. Railonseurantajärjestelmät ovat kuitenkin kalliita, eivätkä ne toimi luotettavasti kaikissa olosuhteissa. Diplomityössä tutkittiin uutta MIG/MAG-hitsauksen reaaliaikaiseen tunkeuman hallintaan kehitettyä säätöjärjestelmää. Työn tavoitteina olivat säätöjärjestelmän luotettavan toiminnan takaavien reunaehtojen ja kosketussuutinetäisyyden suositusrajojen määrittäminen. Tavoitteiden täyttämiseksi työn kokeellisessa osiossa suoritettiin laaja hitsauskokeiden sarja, jossa hitsattavina materiaaleina käytettiin seostamatonta ja runsasseosteista terästä.

Reaction Kinetics and Viscosity Modelling in the Fusion Syntheses of Ca- and Ca/Mg-resinates

Rosin is a natural product from pine forests and it is used as a raw material in resinate syntheses. Resinates are polyvalent metal salts of rosin acids and especially Ca- and Ca/Mg- resinates find wide application in the printing ink industry. In this thesis, analytical methods were applied to increase general knowledge of resinate chemistry and the reaction kinetics was studied in order to model the non linear solution viscosity increase during resinate syntheses by the fusion method. Solution viscosity in toluene is an important quality factor for resinates to be used in printing inks. The concept of critical resinate concentration, c crit, was introduced to define an abrupt change in viscosity dependence on resinate concentration in the solution. The concept was then used to explain the non-inear solution viscosity increase during resinate syntheses. A semi empirical model with two estimated parameters was derived for the viscosity increase on the basis of apparent reaction kinetics. The model was used to control the viscosity and to predict the total reaction time of the resinate process. The kinetic data from the complex reaction media was obtained by acid value titration and by FTIR spectroscopic analyses using a conventional calibration method to measure the resinate concentration and the concentration of free rosin acids. A multivariate calibration method was successfully applied to make partial least square (PLS) models for monitoring acid value and solution viscosity in both mid-infrared (MIR) and near infrared (NIR) regions during the syntheses. The calibration models can be used for on line resinate process monitoring. In kinetic studies, two main reaction steps were observed during the syntheses. First a fast irreversible resination reaction occurs at 235 °C and then a slow thermal decarboxylation of rosin acids starts to take place at 265 °C. Rosin oil is formed during the decarboxylation reaction step causing significant mass loss as the rosin oil evaporates from the system while the viscosity increases to the target level. The mass balance of the syntheses was determined based on the resinate concentration increase during the decarboxylation reaction step. A mechanistic study of the decarboxylation reaction was based on the observation that resinate molecules are partly solvated by rosin acids during the syntheses. Different decarboxylation mechanisms were proposed for the free and solvating rosin acids. The deduced kinetic model supported the analytical data of the syntheses in a wide resinate concentration region, over a wide range of viscosity values and at different reaction temperatures. In addition, the application of the kinetic model to the modified resinate syntheses gave a good fit. A novel synthesis method with the addition of decarboxylated rosin (i.e. rosin oil) to the reaction mixture was introduced. The conversion of rosin acid to resinate was increased to the level necessary to obtain the target viscosity for the product at 235 °C. Due to a lower reaction temperature than in traditional fusion synthesis at 265 °C, thermal decarboxylation is avoided. As a consequence, the mass yield of the resinate syntheses can be increased from ca. 70% to almost 100% by recycling the added rosin oil.

Sensor Fusion of Proprioception, Force and Vision in Estimation and Robot

Sensor-based robot control allows manipulation in dynamic environments with uncertainties. Vision is a versatile low-cost sensory modality, but low sample rate, high sensor delay and uncertain measurements limit its usability, especially in strongly dynamic environments. Force is a complementary sensory modality allowing accurate measurements of local object shape when a tooltip is in contact with the object. In multimodal sensor fusion, several sensors measuring different modalities are combined to give a more accurate estimate of the environment. As force and vision are fundamentally different sensory modalities not sharing a common representation, combining the information from these sensors is not straightforward. In this thesis, methods for fusing proprioception, force and vision together are proposed. Making assumptions of object shape and modeling the uncertainties of the sensors, the measurements can be fused together in an extended Kalman filter. The fusion of force and visual measurements makes it possible to estimate the pose of a moving target with an end-effector mounted moving camera at high rate and accuracy. The proposed approach takes the latency of the vision system into account explicitly, to provide high sample rate estimates. The estimates also allow a smooth transition from vision-based motion control to force control. The velocity of the end-effector can be controlled by estimating the distance to the target by vision and determining the velocity profile giving rapid approach and minimal force overshoot. Experiments with a 5-degree-of-freedom parallel hydraulic manipulator and a 6-degree-of-freedom serial manipulator show that integration of several sensor modalities can increase the accuracy of the measurements significantly.

Inversion and assimilation methods with applications in geophysical remote sensing

Stratospheric ozone can be measured accurately using a limb scatter remote sensing technique at the UV-visible spectral region of solar light. The advantages of this technique includes a good vertical resolution and a good daytime coverage of the measurements. In addition to ozone, UV-visible limb scatter measurements contain information about NO2, NO3, OClO, BrO and aerosols. There are currently several satellite instruments continuously scanning the atmosphere and measuring the UVvisible region of the spectrum, e.g., the Optical Spectrograph and Infrared Imager System (OSIRIS) launched on the Odin satellite in February 2001, and the Scanning Imaging Absorption SpectroMeter for Atmospheric CartograpHY (SCIAMACHY) launched on Envisat in March 2002. Envisat also carries the Global Ozone Monitoring by Occultation of Stars (GOMOS) instrument, which also measures limb-scattered sunlight under bright limb occultation conditions. These conditions occur during daytime occultation measurements. The global coverage of the satellite measurements is far better than any other ozone measurement technique, but still the measurements are sparse in the spatial domain. Measurements are also repeated relatively rarely over a certain area, and the composition of the Earth’s atmosphere changes dynamically. Assimilation methods are therefore needed in order to combine the information of the measurements with the atmospheric model. In recent years, the focus of assimilation algorithm research has turned towards filtering methods. The traditional Extended Kalman filter (EKF) method takes into account not only the uncertainty of the measurements, but also the uncertainty of the evolution model of the system. However, the computational cost of full blown EKF increases rapidly as the number of the model parameters increases. Therefore the EKF method cannot be applied directly to the stratospheric ozone assimilation problem. The work in this thesis is devoted to the development of inversion methods for satellite instruments and the development of assimilation methods used with atmospheric models.

Energy and raw material consumption analysis of powder bed fusion: case study: CNC machining and laser additive manufacturing

Laser additive manufacturing (LAM), known also as 3D printing, is a powder bed fusion (PBF) type of additive manufacturing (AM) technology used to manufacture metal parts layer by layer by assist of laser beam. The development of the technology from building just prototype parts to functional parts is due to design flexibility. And also possibility to manufacture tailored and optimised components in terms of performance and strength to weight ratio of final parts. The study of energy and raw material consumption in LAM is essential as it might facilitate the adoption and usage of the technique in manufacturing industries. The objective this thesis was find the impact of LAM on environmental and economic aspects and to conduct life cycle inventory of CNC machining and LAM in terms of energy and raw material consumption at production phases. Literature overview in this thesis include sustainability issues in manufacturing industries with focus on environmental and economic aspects. Also life cycle assessment and its applicability in manufacturing industry were studied. UPLCI-CO2PE! Initiative was identified as mostly applied exiting methodology to conduct LCI analysis in discrete manufacturing process like LAM. Many of the reviewed literature had focused to PBF of polymeric material and only few had considered metallic materials. The studies that had included metallic materials had only measured input and output energy or materials of the process and compared to different AM systems without comparing to any competitive process. Neither did any include effect of process variation when building metallic parts with LAM. Experimental testing were carried out to make dissimilar samples with CNC machining and LAM in this thesis. Test samples were designed to include part complexity and weight reductions. PUMA 2500Y lathe machine was used in the CNC machining whereas a modified research machine representing EOSINT M-series was used for the LAM. The raw material used for making the test pieces were stainless steel 316L bar (CNC machined parts) and stainless steel 316L powder (LAM built parts). An analysis of power, time, and the energy consumed in each of the manufacturing processes on production phase showed that LAM utilises more energy than CNC machining. The high energy consumption was as result of duration of production. Energy consumption profiles in CNC machining showed fluctuations with high and low power ranges. LAM energy usage within specific mode (standby, heating, process, sawing) remained relatively constant through the production. CNC machining was limited in terms of manufacturing freedom as it was not possible to manufacture all the designed sample by machining. And the one which was possible was aided with large amount of material removed as waste. Planning phase in LAM was shorter than in CNC machining as the latter required many preparation steps. Specific energy consumption (SEC) were estimated in LAM based on the practical results and assumed platform utilisation. The estimated platform utilisation showed SEC could reduce when more parts were placed in one build than it was in with the empirical results in this thesis (six parts).

Organization of the marketing communication activities after fusion - the integration and the decision making processes

This master’s thesis was made in order to gain answers to the question of how the integration of the marketing communications and the decision making related to it in a geographically dispersed service organization could be improved in a situation where an organization has gone through a merger. The effects of the organizational design dimensions towards the integration of the marketing communications and the decision making related to it was the main focus. A case study as a research strategy offered a perfect frames for an exploratory study and the data collection was conducted by semi-structured interviews and observing. The main finding proved that from the chosen design dimensions, decentralization, coordination and power, could be found specific factors that in a geographically dispersed organization are affecting the integration of the marketing communications negatively. The effects can be seen mostly in the decision making processes, roles and in the division of responsibility, which are affecting the other dimensions and by this, the integration. In a post-merger situation, the coordination dimension and especially the information asymmetry and the information flow seem to have a largest affect towards the integration of the marketing communications. An asymmetric information distribution with the lack of business and marketing education resulted in low self-assurance and at the end in fragmented management and to the inability to set targets and make independent decisions. As conclusions it can be stated, that with the organizational design dimensions can the effects of a merger towards the integration process of the marketing communications to be evaluated.

A human-centric service approach for architecting and reengineering global system

Production of a new system in any range is expanding dramatically and new ideas are there upon introduced, the logic stands behind the matter is the growth of application of the internet and granting web-based systems. Before producing a system and distribute to the customer, various aspects should be studied which multiple the profit of the system. The process of productizing a new system from being unprocessed idea until delivers to the final user has been unambiguous. In this thesis, the systematize service in a way that benefits both the customer and provider, along with an effort to establish trust and diminish customer’s risk and increase service productivity are in detail presented. Characteristics of Servitization and Productization as two faces of one coin have been interpreted. Apart from the abovementioned issues state of art, service-oriented architecture (SOA) and New Service Development (NSD) has been included in this report for solving the problem of gradually decline in value of companies.

On the Properties and Cosmology of Q-balls

The properties and cosmological importance of a class of non-topological solitons, Q-balls, are studied. Aspects of Q-ball solutions and Q-ball cosmology discussed in the literature are reviewed. Q-balls are particularly considered in the Minimal Supersymmetric Standard Model with supersymmetry broken by a hidden sector mechanism mediated by either gravity or gauge interactions. Q-ball profiles, charge-energy relations and evaporation rates for realistic Q-ball profiles are calculated for general polynomial potentials and for the gravity mediated scenario. In all of the cases, the evaporation rates are found to increase with decreasing charge. Q-ball collisions are studied by numerical means in the two supersymmetry breaking scenarios. It is noted that the collision processes can be divided into three types: fusion, charge transfer and elastic scattering. Cross-sections are calculated for the different types of processes in the different scenarios. The formation of Q-balls from the fragmentation of the Aflieck-Dine -condensate is studied by numerical and analytical means. The charge distribution is found to depend strongly on the initial energy-charge ratio of the condensate. The final state is typically noted to consist of Q- and anti-Q-balls in a state of maximum entropy. By studying the relaxation of excited Q-balls the rate at which excess energy can be emitted is calculated in the gravity mediated scenario. The Q-ball is also found to withstand excess energy well without significant charge loss. The possible cosmological consequences of these Q-ball properties are discussed.