Chelyabinsk CHP-3 “locked power” problem solving

All over the world power systems become bigger and bigger every day. New equipment is installed, new feeders are constructed, new power units are installed. Some old elements of the network, however, are not changed in time. As a result, “bottlenecks” for capacity transmission can occur. By locked power problem the situation when a power plant has installed capacity exceeding the power it can actually deliver is usually meant. Regime, scheme or even technical restrictions-related issues usually cause this kind of problem. It is really important, since from the regime point of view it is typical decision to have a mobile capacity reserve, in case of malfunctions. And, what can be even more significant, power plant owner (JSC Fortum in our case) losses his money because of selling less electrical energy. The goal of master`s thesis is to analyze the current state of Chelyabinsk power system and the CHP-3 (Combined Heat and Power plant) in particular in relation with it`s ability to deliver the whole capacity of the CHP in it`s existing state and also taking into consideration the prospect of power unit 3 installation by the fourth quarter of 2010. The thesis contains some general information about the UPS of Russia, CPS of Ural, power system of Chelyabinsk and the Chelyabinsk region itself. Then the CHP-3 is described from technical point of view with it`s equipment observation. Regimes for the nowadays power system and for the system after the power unit 3 installation are reviewed. The problems occurring are described and, finally, a solution is offered.

Capacity of an I-beam made of S960 QC based on Eurocode 3

The capacity of beams is a very important factor in the study of durability of structures and structural members. The capacity of a high-strength steel I-beam made of S960 QC was investigated in this study. The investigation included assessment of the service limits and ultimate limits of the steel beam. The thesis was done according to European standards for steel structures, Eurocode 3. An analytical method was used to determine the throat thickness, deformation, elastic and plastic moment capacities as well as the fatigue life of the beam. The results of the analytical method were compared with those obtained by Finite Element Analysis (FEA). Elastic moment capacity obtained by the analytical method was 172 kNm. FEA and the analytical method predicted the maximum lateral-torsional buckling (LTB) capacity in the range of 90-93 kNm and the probability of failure as a result of LTB is estimated to be 50%. The lateral buckling capacity meant that the I-beam can carry a safe load of 300 kN instead of the initial load of 600 kN. The beam is liable to fail shortly after exceeding the elastic moment capacity. Based on results in of the different approaches, it was noted that FEA predicted higher deformation values on the load-deformation curve than the analytical results. However, both FEA and the analytical methods predicted identical results for nominal stress range and moment capacities. Fatigue life was estimated to be in the range of 53000-64000 cycles for bending stress range using crack propagation equation and strength-life approach. As Eurocode 3 is limited to steel grades up to S690, results for S960 must be verified with experimental data and appropriate design rules.

Turvallisuustoimintojen käyttö ydinvoimalaitoksilla

Tässä diplomityössä tarkastellaan turvallisuustoiminto-käsitteen määrittelyä ja käyttöä osana ydinvoimalaitosten turvallisuuden varmistamista. Työssä kuvataan paine- ja kiehutusvesilaitosten toiminnan yleispiirteet, sekä Teollisuuden Voima Oy:n (TVO) laitosten Olkiluoto 1 & 2 sekä Olkiluoto 3 tarkempi turvallisuustoiminta turvallisuusjärjestelmien ja -automaation osalta. Työssä esitellään eräs tapa määrittää turvallisuustoimintoja. Malli perustuu hierarkkiseen rakenteeseen, jossa ylimpänä ovat laitostason turvallisuustoiminnot ja alimpana turvallisuustoimintoihin osallistuvien laitteiden ja niiden osien toiminnot. Turvallisuustoimintoja on mahdollista käyttää ydinvoimalaitoksen turvallisuusluokituksen tekemiseen ja perustelemiseen. Turvallisuustoiminto kertoo suoraan luokiteltavan kohteen turvallisuusmerkityksen. Kohteen turvallisuusmerkityksen selvittäminen, eli liittäminen turvallisuustoimintoon, voi olla vaikeaa. Turvallisuustoimintoja on myös mahdollista käyttää laitoksen turvallisuusautomaation riittävän varmistamisen (mm. redundanttisuus, diversiteetti ja erotus) osoittamiseen erityisesti ohjelmoitavan automaation yhteydessä. Turvallisuustoimintoja voidaan hyödyntää laitoksen hätätilanneohjeiden kehittämisessä ja myös laitoksenmuun turvallisuusdokumentaation selkeyttämisessä. Työn tuloksena kehitettiin käyville laitoksille (OL1 & 2) aikaisempaa kattavammat turvallisuustoiminnot. Lisäksi tarkasteltiin rakenteilla olevalle laitokselle (OL3) määriteltyjä turvallisuustoimintoja.

Laskentamalli PKL-koelaitteiston pienen vuodon kokeen simuloimiseksi Apros-ohjelmistolla

Työn tavoitteena oli tehdä Apros-laskentamalli PKL-koelaitteistosta ja testata kuinka hyvin Apros pystyy laskemaan PKL-koelaitteistolla suoritetun E2.2 pienen vuodon kokeen. Tavoitteena oli myös tarkastella boorittoman veden tulpan etenemistä pienen vuodon kokeen aikana. PKL-koelaitteisto vastaa saksalaista sähköteholtaan 1300 MW olevaa Philippsburg 2 painevesilaitosta. Koelaitteiston tilavuudet ja teho on skaalattu kertoimella 145. Työssä tehdyllä laskentamallilla tarkasteltiin boorittoman veden tulpan liikkumista pienen vuodon kokeen aikana. Kun malli oli valmis, laskenta suoritettiin Apros 5.05 versiolla. Boorittoman veden tulpan etenemisen laskennassa käytettiin toisen kertaluvun diskretointia, jolla booripitoisuuden muutokset säilyvät teräväreunaisina. Laskentamalli pystyi kuvaamaan koelaitteistolla suoritetussa pienen vuodon kokeessa tapahtuneet ilmiöt varsin hyvin. Eroa koetuloksiintuli pääkiertopiirien luonnonkiertojen alkamishetkistä ja primääripaineen käyttäytymisessä. Kokeen alkutilanne ei ollut stationääritila, joten alkutilanteen asettamisessa oli hankaluuksia. Varsinkin pääkiertopiirien veden pinnankorkeuksienasettamisessa oli vaikeuksia, koska veden pinnankorkeuksien erot pyrkivät tasoittumaan nopeasti kokeen aikana. Apros pystyi laskemaan PKL-koelaitteistolla suoritetun pienen vuodon kokeen hyvin. Mallilla tulisi kuitenkin laskea vielä toisentyyppisiäkin kokeita, ennen kuin voidaan varmuudella tietää mallin toimivuus. PKL-koelaitteisto vastaa pääpiirteiltään Suomeen rakennettavaa Olkiluoto 3 ydinvoimalaitosta. Tehty työ antaa lisävarmuutta, kun Olkiluoto 3 laitoksen turvallisuustarkasteluita tehdään.

Computing the diameter of Coxeter groups

This thesis addresses the problem of computing the minimal and maximal diameter of the Cayley graph of Coxeter groups. We first present and assert relevant parts of polytope theory and related Coxeter theory. After this, a method of contracting the orthogonal projections of a polytope from Rd onto R2 and R3, d ¸ 3 is presented. This method is the Equality Set Projection algorithm that requires a constant number of linearprogramming problems per facet of the projection in the absence of degeneracy. The ESP algorithm allows us to compute also projected geometric diameters of high-dimensional polytopes. A representation set of projected polytopes is presented to illustrate the methods adopted in this thesis.

Visualization of communication system testing logs

During the past decades testing has matured from ad-hoc activity into being an integral part of the development process. The benefits of testing are obvious for modern communication systems, which operate in heterogeneous environments amongst devices from various manufacturers. The increased demand for testing also creates demand for tools and technologies that support and automate testing activities. This thesis discusses applicability of visualization techniques in the result analysis part of the testing process. Particularly, the primary focus of this work is visualization of test execution logs produced by a TTCN-3 test system. TTCN-3 is an internationally standardized test specification and implementation language. The TTCN-3 standard suite includes specification of a test logging interface and a graphical presentation format, but no immediate relationship between them. This thesis presents a technique for mapping the log events to the graphical presentation format along with a concrete implementation, which is integrated with the Eclipse Platform and the OpenTTCN Tester toolchain. Results of this work indicate that for majority of the log events, a visual representation may be derived from the TTCN-3 standard suite. The remaining events were analysed and three categories relevant in either log analysis or implementation of the visualization tool were identified: events indicating insertion of something into the incoming queue of a port, events indicating a mismatch and events describing the control flow during the execution. Applicability of the results is limited into the domain of TTCN-3, but the developed mapping and the implementation may be utilized with any TTCN-3 tool that is able to produce the execution log in the standardized XML format.

Targeted Therapy Possibilities for Metastatic Melanoma

The incidence of malignant melanoma of the skin has been steadily rising worldwide during the past decades. Most early detected primary tumors can be removed surgically and the prognosis is good. However, at the same time there still is no permanent cure for metastatic melanoma and its prognosis is poor, although lately new effective drugs have emerged. In this thesis, four different approaches of experimental therapy for metastatic melanoma were studied. Endogenous cis-Urocanic acid (UCA) is found in every individual’s skin, where exposure to UV light from the sun generates it from its inactive trans conformation. Cis- UCA was found to destroy malignant melanoma cells in culture under an acidified pH and sufficient concentration through caspase-3 mediated apoptosis. Furthermore, cis-UCA is able to considerably diminish the growth rate in human melanoma tumors on living SCID mice. Using replication-competent Semliki Forest viruses, human melanoma tumors grown in SCID mice were dramatically shrunken as the fulminant production of viruses in melanoma cells leads them to apoptosis within 72 hours. Small oligopeptides attaching to melanoma cells were identified using in vivo phage display. The melanoma-specific peptides found were further tested in vitro on adenoviruses. Ultimately, the adenoviral retargeting using the peptides was tested in vivo. One peptide homed to human transferring receptor upregulated on melanoma cells. In order to kill the malignant melanoma cells with the retargeted adenoviruses, the viruses should carry genetic material producing apoptotic proteins in the cancer tissue. TIMP-3 has been identified as a good candidate for such a protein, as it inhibits malignant cell adhesion as well as promotes apoptosis through a caspase-8 pathway. It is further shown here that adenovirally delivered TIMP-3 is even more potent, as it could kill non-adherent cancer cells, lacking the fully functional death receptor signalling pathway. Adenovirally delivered TIMP-2 also showed marked antitumor effects in human malignant melanoma xenografts on SCID mice both in ex vivo and systemic delivery.

Pencil grip : a descriptive model and four empirical studies

Previous studies on pencil grip have typically dealt with the developmental aspects in young children while handwriting research is mainly concerned with speed and legibility. Studies linking these areas are few. Evaluation of the existing pencil grip studies is hampered by methodological inconsistencies. The operational definitions of pencil grip arerational but tend to be oversimplified while detailed descriptors tend to be impractical due to their multiplicity. The present study introduces a descriptive two-dimensional model for the categorisation of pencil grip suitable for research applications in a classroom setting. The model is used in four empirical studies of children during the first six years of writing instruction. Study 1 describes the pencil grips observed in a large group of pupils in Finland (n = 504). The results indicate that in Finland the majority of grips resemble the traditional dynamic tripod grip. Significant genderrelated differences in pencil grip were observed. Study 2 is a longitudinal exploration of grip stability vs. change (n = 117). Both expected and unexpected changes were observed in about 25 per cent of the children's grips over four years. A new finding emerged using the present model for categorisation: whereas pencil grips would change, either in terms of ease of grip manipulation or grip configuration, no instances were found where a grip would have changed concurrently on both dimensions. Study 3 is a cross-cultural comparison of grips observed in Finland and the USA (n = 793). The distribution of the pencil grips observed in the American pupils was significantly different from those found in Finland. The cross-cultural disparity is most likely related to the differences in the onset of writing instruction. The differences between the boys' and girls' grips in the American group were non-significant.An implication of Studies 2 and 3 is that the initial pencil grip is of foremost importance since pencil grips are largely stable over time. Study 4 connects the pencil grips to assessment of the mechanics of writing (n = 61). It seems that certain previously not recommended pencil grips might nevertheless be includedamong those accepted since they did not appear to hamper either fluency or legibility.

D. Mart. Lutheruxen Catechismus, ulostoimitusten cansa

1) Jumalan kymmenen käsky-sanat. - 2)Uscon tunnustus. - 3) Isä meidän rucous. - 4) Casten sacramentti. - 5) Rippi eli synnin päästö. - 6) Altarin sacramentti. - 7) Huonen taulu. - 8) Christilliset kysymyxet wastausten canssa. d. Mart. Lutheruxelda nijen eteen astetut jotca altarin sacramendillä käydä tahtowat.- 9) seurwat muutamat paicat sijtä pyhästä Raamatusta caickille chritityille erinomattain nuorelle cansalle heidän christillisess uscosans ojennukxexi sopiwaisest (51. psalmi, Esa 53 lucu, p. Matteuxen ewangeliumi kirjan 5. lucu, 6. lucu, 7. lucu).- 10) Serva Deus verbum tuum. - 11) Da pacem Domine.

Extended hydrogen photoproduction by nitrogen-fixing cyanobacteria

Cyanobacteria are the only prokaryotic organisms performing oxygenic photosynthesis. They comprise a diverse and versatile group of organisms in aquatic and terrestrial environments. Increasing genomic and proteomic data launches wide possibilities for their employment in various biotechnical applications. For example, cyanobacteria can use solar energy to produce H2. There are three different enzymes that are directly involved in cyanobacterial H2 metabolism: nitrogenase (nif) which produces hydrogen as a byproduct in nitrogen fixation; bidirectional hydrogenase (hox) which functions both in uptake and in production of H2; and uptake hydrogenase (hup) which recycles the H2 produced by nitrogenase back for the utilization of the cell. Cyanobacterial strains from University of Helsinki Cyanobacteria Collection (UHCC), isolated from the Baltic Sea and Finnish lakes were screened for efficient H2 producers. Screening about 400 strains revealed several promising candidates producing similar amounts of H2 (during light) as the ΔhupL mutant of Anabaena PCC 7120, which is specifically engineered to produce higher amounts of H2 by the interruption of uptake hydrogenase. The optimal environmental conditions for H2 photoproduction were significantly different between various cyanobacterial strains. All suitable strains revealed during screening were N2-fixing, filamentous and heterocystous. The top ten H2 producers were characterized for the presence and activity of the enzymes involved in H2 metabolism. They all possess the genes encoding the conventional nitrogenase (nifHDK1). However, the high H2 photoproduction rates of these strains were shown not to be directly associated with the maximum capacities of highly active nitrogenase or bidirectional hydrogenase. Most of the good producers possessed a highly active uptake hydrogenase, which has been considered as an obstacle for efficient H2 production. Among the newly revealed best H2 producing strains, Calothrix 336/3 was chosen for further, detailed characterization. Comparative analysis of the structure of the nif and hup operons encoding the nitrogenase and uptake hydrogenase enzymes respectively showed minor differences between Calothrix 336/3 and other N2-fixing model cyanobacteria. Calothrix 336/3 is a filamentous, N2-fixing cyanobacterium with ellipsoidal, terminal heterocysts. A common feature of Calothrix 336/3 is that the cells readily adhere to substrates. To make use of this feature, and to additionally improve H2 photoproduction capacity of the Calothrix 336/3 strain, an immobilization technique was applied. The effects of immobilization within thin alginate films were evaluated by examining the photoproduction of H2 of immobilized Calothrix 336/3 in comparison to model strains, the Anabaena PCC 7120 and its ΔhupL mutant. In order to achieve optimal H2 photoproduction, cells were kept under nitrogen starved conditions (Ar atmosphere) to ensure the selective function of nitrogenase in reducing protons to H2. For extended H2 photoproduction, cells require CO2 for maintenance of photosynthetic activity and recovery cycles to fix N2. Application of regular H2 production and recovery cycles, Ar or air atmospheres respectively, resulted in prolongation of H2 photoproduction in both Calothrix 336/3 and the ΔhupL mutant of Anabaena PCC 7120. However, recovery cycles, consisting of air supplemented with CO2, induced a strong C/N unbalance in the ΔhupL mutant leading to a decrease in photosynthetic activity, although total H2 yield was still higher compared to the wild-type strain. My findings provide information about the diversity of cyanobacterial H2 capacities and mechanisms and provide knowledge of the possibilities of further enhancing cyanobacterial H2 production.