Tulevaisuuden kriisinhallintaa kehittämässä : etnografinen matka Multinational experimentation -yhteisöön ja -käytäntöön

Teksti perustuu 9.6.2012 Tampereen yliopistossa järjestetyn väitöstilaisuuden lectio praecursoria -esitelmään.

Experimentation on Wind Powered Hydraulic Heating System

It is common knowledge of the world’s dependency on fossil fuel for energy, its unsustainability on the long run and the changing trend towards renewable energy as an alternative energy source. This aims to cut down greenhouse gas emission and its impact on the rate of ecological and climatic change. Quite remarkably, wind energy has been one of many focus areas of renewable energy sources and has attracted lots of investment and technological advancement. The objective of this research is to explore wind energy and its application in household heating. This research aims at applying experimental approach in real time to study and verify a virtually simulated wind powered hydraulic house heating system. The hardware components comprise of an integrated hydraulic pump, flow control valve, hydraulic fluid and other hydraulic components. The system design and control applies hardware in-the-loop (HIL) simulation setup. Output signal from the semi-empirical turbine modelling controls the integrated motor to generate flow. Throttling the volume flow creates pressure drop across the valve and subsequently thermal power in the system to be outputted using a heat exchanger. Maximum thermal power is achieved by regulating valve orifice to achieve optimum system parameter. Savonius rotor is preferred for its low inertia, high starting torque and ease of design and maintenance characteristics, but lags in power efficiency. A prototype turbine design is used; with power output in range of practical Savonius turbine. The physical mechanism of the prototype turbine’s augmentation design is not known and will not be a focus in this study.

Kalsium-käsittelyn vaikutus materiaalin lastuttavuuteen vannesahauksessa

Diplomityö käsittelee aiemmin Suomessa vähän tutkittua metallin vannesahausta. Työ keskittyy lähinnä tangon sahaukseen vaakatyyppisellä vannesahalla. Työn teoriaosuudessa luodaan silmäys erityyppisiin vannesahoihin ja perehdytään tarkemmin terän teoriaan, mm. terän valmistukseen, terämateriaaleihin, geometriaan, erilaisiin hammasmuotoihin sekä haritukseen. Lisäksi käsitellään lastuamisparametreja ja lastuamisvoimia vannesahauksessa. Tarkasteltavana on myös vannesahauksen kustannusrakenne ja sen muodostuminen. Kokeellisessa osiossa tutkitaan teräksille suoritettavan lastuttavuutta parantavan kalsium-käsittelyn vaikutusta sahattavuuteen. Kalsium-käsittely parantaa sahattavuutta 15-80 % käytettävästä terämateriaalista ja tarkastelutavasta riippuen. Kokeellisessa osiossa suoritetaan myös terävertailu kolmen eri terän välillä. Terävertailulla pyritään löytämään kustannustehokkain, eli pienimmän kustannuksen katkaisua kohti tuottava terä vertailuun valittujen vaihtoehtojen joukosta. Kustannustehokkaimmaksi teräksi osoittautui Amadan Super HLG M42 Bi-metalliterä.

Suunnittelujärjestelmien hyödyntäminen kartonkitehtaan kunnossapidon laitossuunnittelussa

Tutkimus selvittää ajanmukaisien suunnittelujärjestelmien ominaisuuksia ja soveltuvuutta kartonkitehtaan kunnossapidon laitossuunnitteluun. Tutkimus on tehty keräämällä tietoja kirjallisista julkaisuista sekä tekemällä haastatteluja, empiirisiä kokeita ja kyselytutkimus. Saadut tutkimustulokset ovat suhteellisia ja niitä verrataan eräässä kartonkitehtaassa käytössä olevaan järjestelmään. Tutkimuksen tuloksina esitetään ajanmukaisien suunnittelujärjestelmien käytöllä saavutettavissa olevia hyötyjä ja käyttöön liittyviä ongelmia sekä näiden järjestelmien soveltuvuutta ja vertailukriteerejä laitoskäyttöön. Lisäksi käsitellään ajanmukaisiin järjestelmiin investoinnin kannattavuutta ja herkkyystekijöitä investointilaskelman (NPV) avulla. Tuloksena saatiin, etteivät tämänhetkiset suunnittelujärjestelmät sovi parhaalla mahdollisella tavalla yritysten suunnittelun ja tiedonhallinnan kokonaisuuteen. Keinona, jolla voidaan parantaa suunnittelujärjestelmien laitoskäyttöön sopivuutta, esitetään metsäteollisuuskonsernien välistä yhteistyötä.

Developing and Applying Generative Market Intelligence within Multinational Companies

Tutkielman tarkoitus on kehittää monikansallisille yrityksille tuottavan markkinaälyn malli, jonka avulla yritykset pystyvät käsittelemään muuttuvasta ja globalisoituvasta markkinaympäristöstä aiheutuvaa epävarmuutta. Malli koostuu pääosin kolmesta käsitteestä: markkinainformaation prosessoinnista, markkinasuuntautuneisuudesta ja organisationaalisesta oppimisesta. Tutkimuksessa osoitetaan, kuinka näiden samanaikainen soveltaminen johtaa synergiaetuihin. Lähdeaineistona käytettiin alan kirjallisuutta. Lisäksi haastateltiin neljää johtajaa monikansallisista yrityksistä. Käytännössä markkinaälyn soveltamisen haasteet liittyvät lähinnä markkinainformaation prosessoinnin asenteellisiin ja psykologisiin aspekteihin. Ihmisten tulisi ymmärtää, että koko yritys hyötyy heidän halukkuudestaan tiedon tuottamiseen ja jakamiseen. Lisäksi tietoa itsessään voimavarana tulisi kunnioittaa

Partnering in the Dynamic Environment: The Role of Trust in Asymmetric Technology Partnership Formation

The purpose of this study was to increase the understanding of the role and nature of trust in asymmetric technology partnership formation. In the knowledge-based "learning race" knowledge is considered as a primary source for competitive advantage. In the emerging ICT sector the high pace of technological change, the convergence of technologies and industries as well as the increasing complexity and uncertainty have forced even the largest players to seek cooperation for complementary knowledge and capabilities. Small technology firms need the complementary resources and legitimacy of the large firms to grow and compete in the global market place. Most of the earlier research indicates, however, that partnerships with asymmetric size, managerial resources and cultures have failed. A basic assumption supported by earlier research was that trust is a critical factor in asymmetric technology partnership formation. Asymmetric technology partnership formation is a dynamic and multi-dimensional process, and consequently a holistic research approach was selected. Research issue was approached from different levels: the individual decision-maker, the firm and the relationship between the parties. Also the impact of the dynamic environment and technology content was analyzed. A multitheoretical approach and a qualitative research method with in-depth interviews in five large ICT companies and eight small ICT companies enabled a holistic and rich view of the research issue. Study contributes on the scarce understanding on the nature and evolution of trust in asymmetric technology partnership formation. It sheds also light on the specific nature of asymmetric technology partnerships. The partnerships were found to be tentative and the diverse strategic intent of small and large technology firms appeared as a major challenge. The role of the boundary spanner was highlighted as a possibility to match the incompatible organizational cultures. A shared vision was found to be a pre-condition for individual-based fast trust leading to intuitive decision-making and experimentation. The relationships were tentative and they were continuously re-evaluated through the key actors' sense making of the technology content, asymmetry and the dynamic environment. A multi-dimensional conceptualization for trust was created and propositions on the role and nature of trust for further research are given. The purpose of this study was to increase the understanding of the role and nature of trust in asymmetric technology partnership formation. In the knowledge-based "learning race" knowledge is considered as a primary source for competitive advantage. In the emerging ICT sector the high pace of technological change, the convergence of technologies and industries as well as the increasing complexity and uncertainty have forced even the largest players to seek cooperation for complementary knowledge and capabilities. Small technology firms need the complementary resources and legitimacy of the large firms to grow and compete in the global market place. Most of the earlier research indicates, however, that partnerships with asymmetric size, managerial resources and cultures have failed. A basic assumption supported by earlier research was that trust is a critical factor in asymmetric technology partnership formation. Asymmetric technology partnership formation is a dynamic and multi-dimensional process, and consequently a holistic research approach was selected. Research issue was approached from different levels: the individual decision-maker, the firm and the relationship between the parties. Also the impact of the dynamic environment and technology content was analyzed. A multitheoretical approach and a qualitative research method with in-depth interviews in five large ICT companies and eight small ICT companies enabled a holistic and rich view of the research issue. Study contributes on the scarce understanding on the nature and evolution of trust in asymmetric technology partnership formation. It sheds also light on the specific nature of asymmetric technology partnerships. The partnerships were found to be tentative and the diverse strategic intent of small and large technology firms appeared as a major challenge. The role of the boundary spanner was highlighted as a possibility to match the incompatible organizational cultures. A shared vision was found to be a pre-condition for individual-based fast trust leading to intuitive decision-making and experimentation. The relationships were tentative and they were continuously re-evaluated through the key actors' sense making of the technology content, asymmetry and the dynamic environment. A multi-dimensional conceptualization for trust was created and propositions on the role and nature of trust for further research are given.

Studies of Liquid-liquid Separation in Fibre Coalescer

This thesis focuses on fibre coalescers whose efficiency is based on the surface properties/characteristics. They have the ability to preferentially wet or interact with one or more of the fluids to be separated. Thus, the interfacial phenomena governing the separation efficiency of the coalescers is investigated depending on physical factors such as flowrates, phase ratios and coalescer packing density. Design of process equipment to produce and separate of the emulsions was carried out.The experimentation was carried out to test the separation efficiency of the coalescing medias, namely fibreglass, polyester I and polyester II. The performances of the coalescing medias were assessed via droplet size information. In conclusion, the objectives (design of process equipment and experimentation) were achieved. Fibre glass was the best coalescing media, next was polyester I and then finally polyester II. Droplets sizes increased with decreased flowrates and increased packing density of the coalescer. Phase ratio had effect on the droplet sizes of the feed but had no effect on the coalescence of droplets of the feed.

Maritime Safety in the Gulf of Finland. Review on Policy Instruments

Suomenlahden lisääntynyt meriliikenne on herättänyt huolta meriliikenteen turvallisuuden tasosta, ja erityisesti Venäjän öljyviennin kasvu on lisännyt öljyonnettomuuden todennäköisyyttä Suomenlahdella. Erilaiset kansainväliset, alueelliset ja kansalliset ohjauskeinot pyrkivät vähentämään merionnettomuuden riskiä ja meriliikenteen muita haittavaikutuksia. Tämä raportti käsittelee meriturvallisuuden yhteiskunnallisia ohjauskeinoja: ohjauskeinoja yleisellä tasolla, meriturvallisuuden keskeisimpiä säätelijöitä, meriturvallisuuden ohjauskeinoja ja meriturvallisuuspolitiikan tulevaisuuden näkymiä, ohjauskeinojen tehokkuutta ja nykyisen meriturvallisuuden ohjausjärjestelmän heikkouksia. Raportti on kirjallisuuskatsaus meriturvallisuuden yhteiskunnalliseen sääntelyn rakenteeseen ja tilaan erityisesti Suomenlahden meriliikenteen näkökulmasta. Raportti on osa tutkimusprojektia ”SAFGOF - Suomenlahden meriliikenteen kasvunäkymät 2007 - 2015 ja kasvun vaikutukset ympäristölle ja kuljetusketjujen toimintaan” ja sen työpakettia 6 ”Keskeisimmät riskit ja yhteiskunnalliset vaikutuskeinot”. Yhteiskunnalliset ohjauskeinot voidaan ryhmitellä hallinnollisiin, taloudellisiin ja tietoohjaukseen perustuviin ohjauskeinoihin. Meriturvallisuuden edistämisessä käytetään kaikkia näitä, mutta hallinnolliset ohjauskeinot ovat tärkeimmässä asemassa. Merenkulun kansainvälisen luonteen vuoksi meriturvallisuuden sääntely tapahtuu pääosin kansainvälisellä tasolla YK:n ja erityisesti Kansainvälisen merenkulkujärjestön (IMO) toimesta. Lisäksi myös Euroopan Unionilla on omaa meriturvallisuuteen liittyvää sääntelyä ja on myös olemassa muita alueellisia meriturvallisuuden edistämiseen liittyviä elimiä kuten HELCOM. Joitakin meriturvallisuuden osa-alueita säädellään myös kansallisella tasolla. Hallinnolliset meriturvallisuuden ohjauskeinot sisältävät aluksen rakenteisiin ja varustukseen, alusten kunnon valvontaan, merimiehiin ja merityön tekemiseen sekä navigointiin liittyviä ohjauskeinoja. Taloudellisiin ohjauskeinoihin kuuluvat esimerkiksi väylä- ja satamamaksut, merivakuutukset, P&I klubit, vastuullisuus- ja korvauskysymykset sekä taloudelliset kannustimet. Taloudellisten ohjauskeinojen käyttö meriturvallisuuden edistämiseen on melko vähäistä verrattuna hallinnollisten ohjauskeinojen käyttöön, mutta niitä voitaisiin varmasti käyttää enemmänkin. Ongelmana taloudellisten ohjauskeinojen käytössä on se, että ne kuuluvat pitkälti kansallisen sääntelyn piiriin, joten alueellisten tai kansainvälisten intressien edistäminen taloudellisilla ohjauskeinoilla voi olla hankalaa. Tieto-ohjaus perustuu toimijoiden vapaaehtoisuuteen ja yleisen tiedotuksen lisäksi tieto-ohjaukseen sisältyy esimerkiksi vapaaehtoinen koulutus, sertifiointi tai meriturvallisuuden edistämiseen tähtäävät palkinnot. Poliittisella tasolla meriliikenteen aiheuttamat turvallisuusriskit Suomenlahdella on otettu vakavasti ja paljon työtä tehdään eri tahoilla riskien minimoimiseksi. Uutta sääntelyä on odotettavissa etenkin liittyen meriliikenteen ympäristövaikutuksiin ja meriliikenteen ohjaukseen kuten meriliikenteen sähköisiin seurantajärjestelmiin. Myös inhimilliseen tekijän merkitykseen meriturvallisuuden kehittämisessä on kiinnitetty lisääntyvissä määrin huomiota, mutta inhimilliseen tekijän osalta tehokkaiden ohjauskeinojen kehittäminen näyttää olevan haasteellista. Yleisimmin lääkkeeksi esitetään koulutuksen kehittämistä. Kirjallisuudessa esitettyjen kriteereiden mukaan tehokkaiden ohjauskeinojen tulisi täyttää seuraavat vaatimukset: 1) tarkoituksenmukaisuus – ohjauskeinojen täytyy olla sopivia asetetun tavoitteen saavuttamiseen, 2) taloudellinen tehokkuus – ohjauskeinon hyödyt vs. kustannukset tulisi olla tasapainossa, 3) hyväksyttävyys – ohjauskeinon täytyy olla hyväksyttävä asianosaisten ja myös laajemman yhteiskunnan näkökulmasta katsottuna, 4) toimeenpano – ohjauskeinon toimeenpanon pitää olla mahdollista ja sen noudattamista täytyy pystyä valvomaan, 5) lateraaliset vaikutukset – hyvällä ohjauskeinolla on positiivisia seurannaisvaikutuksia muutoinkin kuin vain ohjauskeinon ensisijaisten tavoitteiden saavuttaminen, 6) kannustin ja uuden luominen – hyvä ohjauskeino kannustaa kokeilemaan uusia ratkaisuja ja kehittämään toimintaa. Meriturvallisuutta koskevaa sääntelyä on paljon ja yleisesti ottaen merionnettomuuksien lukumäärä on ollut laskeva viime vuosikymmenien aikana. Suuri osa sääntelystä on ollut tehokasta ja parantanut turvallisuuden tasoa maailman merillä. Silti merionnettomuuksia ja muita vaarallisia tapahtumia sattuu edelleen. Nykyistä sääntelyjärjestelmää voidaan kritisoida monen asian suhteen. Kansainvälisen sääntelyn aikaansaaminen ei ole helppoa: prosessi on yleensä hidas ja tuloksena voi olla kompromissien kompromissi. Kansainvälinen sääntely on yleensä reaktiivista eli ongelmakohtiin puututaan vasta kun jokin onnettomuus tapahtuu sen sijaan että se olisi proaktiivista ja pyrkisi puuttumaan ongelmakohtiin jo ennen kuin jotain tapahtuu. IMO:n työskentely perustuu kansallisvaltioiden osallistumiseen ja sääntelyn toimeenpano tapahtuu lippuvaltioiden toimesta. Kansallisvaltiot ajavat IMO:ssa pääasiallisesti omia intressejään ja sääntelyn toimeenpanossa on suuria eroja lippuvaltioiden välillä. IMO:n kyvyttömyys puuttua havaittuihin ongelmiin nopeasti ja ottaa sääntelyssä huomioon paikallisia olosuhteita on johtanut siihen, että esimerkiksi Euroopan Unioni on alkanut itse säädellä meriturvallisuutta ja että on olemassa sellaisia alueellisia erityisjärjestelyjä kuin PSSA (particularly sensitive sea area – erityisen herkkä merialue). Merenkulkualalla toimii monenlaisia yrityksiä: toisaalta yrityksiä, jotka pyrkivät toimimaan turvallisesti ja kehittämään turvallisuutta vielä korkeammalle tasolle, ja toisaalta yrityksiä, jotka toimivat niin halvalla kuin mahdollista, eivät välitä turvallisuusseikoista, ja joilla usein on monimutkaiset ja epämääräiset omistusolosuhteet ja joita vahingon sattuessa on vaikea saada vastuuseen. Ongelma on, että kansainvälisellä merenkulkualalla kaikkien yritysten on toimittava samoilla markkinoilla. Vastuuttomien yritysten toiminnan mahdollistavat laivaajat ja muut alan toimijat, jotka suostuvat tekemään yhteistyötä niiden kanssa. Välinpitämätön suhtautuminen turvallisuuteen johtuu osaksi myös merenkulun vanhoillisesta turvallisuuskulttuurista. Verrattaessa meriturvallisuuden sääntelyjärjestelmää kokonaisuutena tehokkaiden ohjauskeinoihin kriteereihin, voidaan todeta, että monien kriteerien osalta nykyistä järjestelmää voidaan pitää tehokkaana ja onnistuneena. Suurimmat ongelmat lienevät sääntelyn toimeenpanossa ja ohjauskeinojen kustannustehokkuudessa. Lippuvaltioiden toimeenpanoon perustuva järjestelmä ei toimi toivotulla tavalla, josta mukavuuslippujen olemassa olo on selvin merkki. Ohjauskeinojen, sekä yksittäisten ohjauskeinojen että vertailtaessa eri ohjauskeinoja keskenään, kustannustehokkuutta on usein vaikea arvioida, minkä seurauksena ohjauskeinojen kustannustehokkuudesta ei ole saatavissa luotettavaa tietoa ja tuloksena voi olla, että ohjauskeino on käytännössä pienen riskin eliminoimista korkealla kustannuksella. Kansainvälisen tason meriturvallisuus- (ja merenkulku-) politiikan menettelytavoiksi on ehdotettu myös muita vaihtoehtoja kuin nykyinen järjestelmä, esimerkiksi monitasoista tai polysentristä hallintojärjestelmää. Monitasoisella hallintojärjestelmällä tarkoitetaan järjestelmää, jossa keskushallinto on hajautettu sekä vertikaalisesti alueellisille tasoille että horisontaalisesti ei-valtiollisille toimijoille. Polysentrinen hallintojärjestelmä menee vielä askeleen pidemmälle. Polysentrinen hallintojärjestelmä on hallintotapa, jonka puitteissa kaikentyyppiset toimijat, sekä yksityiset että julkiset, voivat osallistua hallintoon, siis esimerkiksi hallitukset, edunvalvontajärjestöt, kaupalliset yritykset jne. Kansainvälinen lainsäädäntö määrittelee yleiset tasot, mutta konkreettiset toimenpiteet voidaan päättää paikallisella tasolla eri toimijoiden välisessä yhteistyössä. Tämän tyyppisissä hallintojärjestelmissä merenkulkualan todellinen, kansainvälinen mutta toisaalta paikallinen, toimintaympäristö tulisi otetuksi paremmin huomioon kuin järjestelmässä, joka perustuu kansallisvaltioiden keskenään yhteistyössä tekemään sääntelyyn. Tällainen muutos meriturvallisuuden hallinnassa vaatisi kuitenkin suurta periaatteellista suunnanmuutosta, jollaisen toteutumista ei voi pitää kovin todennäköisenä ainakaan lyhyellä tähtäimellä.

Emancipating and developing learning activity: Systemic intervention and re-instrumentation in higher education.

The central theme of this thesis is the emancipation and further development of learning activity in higher education in the context of the ongoing digital transformation of our societies. It was developed in response to the highly problematic mainstream approach to digital re-instrumentation of teaching and studying practises in contemporary higher education. The mainstream approach is largely based on centralisation, standardisation, commoditisation, and commercialisation, while re-producing the general patterns of control, responsibility, and dependence that are characteristic for activity systems of schooling. Whereas much of educational research and development focuses on the optimisation and fine-tuning of schooling, the overall inquiry that is underlying this thesis has been carried out from an explicitly critical position and within a framework of action science. It thus conceptualises learning activity in higher education not only as an object of inquiry but also as an object to engage with and to intervene into from a perspective of intentional change. The knowledge-constituting interest of this type of inquiry can be tentatively described as a combination of heuristic-instrumental (guidelines for contextualised action and intervention), practical-phronetic (deliberation of value-rational aspects of means and ends), and developmental-emancipatory (deliberation of issues of power, self-determination, and growth) aspects. Its goal is the production of orientation knowledge for educational practise. The thesis provides an analysis, argumentation, and normative claim on why the development of learning activity should be turned into an object of individual|collective inquiry and intentional change in higher education, and why the current state of affairs in higher education actually impedes such a development. It argues for a decisive shift of attention to the intentional emancipation and further development of learning activity as an important cultural instrument for human (self-)production within the digital transformation. The thesis also attempts an in-depth exploration of what type of methodological rationale can actually be applied to an object of inquiry (developing learning activity) that is at the same time conceptualised as an object of intentional change within the ongoing digital transformation. The result of this retrospective reflection is the formulation of “optimally incomplete” guidelines for educational R&D practise that shares the practicalphronetic (value related) and developmental-emancipatory (power related) orientations that had been driving the overall inquiry. In addition, the thesis formulates the instrumental-heuristic knowledge claim that the conceptual instruments that were adapted and validated in the context of a series of intervention studies provide means to effectively intervene into existing practise in higher education to support the necessary development of (increasingly emancipated) networked learning activity. It suggests that digital networked instruments (tools and services) generally should be considered and treated as transient elements within critical systemic intervention research in higher education. It further argues for the predominant use of loosely-coupled, digital networked instruments that allow for individual|collective ownership, control, (co-)production, and re-use in other contexts and for other purposes. Since the range of digital instrumentation options is continuously expanding and currently shows no signs of an imminent slow-down or consolidation, individual and collective exploration and experimentation of this realm needs to be systematically incorporated into higher education practise.

Thinking Outside the Box: Enhancing Science Teaching by Combining (Instead of Contrasting) Laboratory and Simulation Activities

The focus of the present work was on 10- to 12-year-old elementary school students’ conceptual learning outcomes in science in two specific inquiry-learning environments, laboratory and simulation. The main aim was to examine if it would be more beneficial to combine than contrast simulation and laboratory activities in science teaching. It was argued that the status quo where laboratories and simulations are seen as alternative or competing methods in science teaching is hardly an optimal solution to promote students’ learning and understanding in various science domains. It was hypothesized that it would make more sense and be more productive to combine laboratories and simulations. Several explanations and examples were provided to back up the hypothesis. In order to test whether learning with the combination of laboratory and simulation activities can result in better conceptual understanding in science than learning with laboratory or simulation activities alone, two experiments were conducted in the domain of electricity. In these experiments students constructed and studied electrical circuits in three different learning environments: laboratory (real circuits), simulation (virtual circuits), and simulation-laboratory combination (real and virtual circuits were used simultaneously). In order to measure and compare how these environments affected students’ conceptual understanding of circuits, a subject knowledge assessment questionnaire was administered before and after the experimentation. The results of the experiments were presented in four empirical studies. Three of the studies focused on learning outcomes between the conditions and one on learning processes. Study I analyzed learning outcomes from experiment I. The aim of the study was to investigate if it would be more beneficial to combine simulation and laboratory activities than to use them separately in teaching the concepts of simple electricity. Matched-trios were created based on the pre-test results of 66 elementary school students and divided randomly into a laboratory (real circuits), simulation (virtual circuits) and simulation-laboratory combination (real and virtual circuits simultaneously) conditions. In each condition students had 90 minutes to construct and study various circuits. The results showed that studying electrical circuits in the simulation–laboratory combination environment improved students’ conceptual understanding more than studying circuits in simulation and laboratory environments alone. Although there were no statistical differences between simulation and laboratory environments, the learning effect was more pronounced in the simulation condition where the students made clear progress during the intervention, whereas in the laboratory condition students’ conceptual understanding remained at an elementary level after the intervention. Study II analyzed learning outcomes from experiment II. The aim of the study was to investigate if and how learning outcomes in simulation and simulation-laboratory combination environments are mediated by implicit (only procedural guidance) and explicit (more structure and guidance for the discovery process) instruction in the context of simple DC circuits. Matched-quartets were created based on the pre-test results of 50 elementary school students and divided randomly into a simulation implicit (SI), simulation explicit (SE), combination implicit (CI) and combination explicit (CE) conditions. The results showed that when the students were working with the simulation alone, they were able to gain significantly greater amount of subject knowledge when they received metacognitive support (explicit instruction; SE) for the discovery process than when they received only procedural guidance (implicit instruction: SI). However, this additional scaffolding was not enough to reach the level of the students in the combination environment (CI and CE). A surprising finding in Study II was that instructional support had a different effect in the combination environment than in the simulation environment. In the combination environment explicit instruction (CE) did not seem to elicit much additional gain for students’ understanding of electric circuits compared to implicit instruction (CI). Instead, explicit instruction slowed down the inquiry process substantially in the combination environment. Study III analyzed from video data learning processes of those 50 students that participated in experiment II (cf. Study II above). The focus was on three specific learning processes: cognitive conflicts, self-explanations, and analogical encodings. The aim of the study was to find out possible explanations for the success of the combination condition in Experiments I and II. The video data provided clear evidence about the benefits of studying with the real and virtual circuits simultaneously (the combination conditions). Mostly the representations complemented each other, that is, one representation helped students to interpret and understand the outcomes they received from the other representation. However, there were also instances in which analogical encoding took place, that is, situations in which the slightly discrepant results between the representations ‘forced’ students to focus on those features that could be generalised across the two representations. No statistical differences were found in the amount of experienced cognitive conflicts and self-explanations between simulation and combination conditions, though in self-explanations there was a nascent trend in favour of the combination. There was also a clear tendency suggesting that explicit guidance increased the amount of self-explanations. Overall, the amount of cognitive conflicts and self-explanations was very low. The aim of the Study IV was twofold: the main aim was to provide an aggregated overview of the learning outcomes of experiments I and II; the secondary aim was to explore the relationship between the learning environments and students’ prior domain knowledge (low and high) in the experiments. Aggregated results of experiments I & II showed that on average, 91% of the students in the combination environment scored above the average of the laboratory environment, and 76% of them scored also above the average of the simulation environment. Seventy percent of the students in the simulation environment scored above the average of the laboratory environment. The results further showed that overall students seemed to benefit from combining simulations and laboratories regardless of their level of prior knowledge, that is, students with either low or high prior knowledge who studied circuits in the combination environment outperformed their counterparts who studied in the laboratory or simulation environment alone. The effect seemed to be slightly bigger among the students with low prior knowledge. However, more detailed inspection of the results showed that there were considerable differences between the experiments regarding how students with low and high prior knowledge benefitted from the combination: in Experiment I, especially students with low prior knowledge benefitted from the combination as compared to those students that used only the simulation, whereas in Experiment II, only students with high prior knowledge seemed to benefit from the combination relative to the simulation group. Regarding the differences between simulation and laboratory groups, the benefits of using a simulation seemed to be slightly higher among students with high prior knowledge. The results of the four empirical studies support the hypothesis concerning the benefits of using simulation along with laboratory activities to promote students’ conceptual understanding of electricity. It can be concluded that when teaching students about electricity, the students can gain better understanding when they have an opportunity to use the simulation and the real circuits in parallel than if they have only the real circuits or only a computer simulation available, even when the use of the simulation is supported with the explicit instruction. The outcomes of the empirical studies can be considered as the first unambiguous evidence on the (additional) benefits of combining laboratory and simulation activities in science education as compared to learning with laboratories and simulations alone.

Music digitalization and its effects on the Finnish music industry stakeholders

For the past two decades the music digitalization has been considered the most significant phenomenon in the music industry as the physical sales have been decreasing rapidly. The advancement of the digital technology and the internet have facilitated the digitalization in the music industry and affected all stages of the music value chain, namely music creation, distribution and consumption. The newly created consumer culture has led to the establishment of novel business models such as music subscriptions and à-la-carte downloads websites and live streaming. The dynamic digital environment has presented the music industry stakeholders with the challenge to adapt to the requirements of the constantly changing modern consumers’ needs and demands. The purpose of this study was to identify how music digitalization can influence change in the Finnish music industry value chain; i.e. how digitalization affects the music industry stakeholders, their functions and inter-relatedness and how the stakeholders are able to react to the changes in the industry. The study was conducted as a qualitative research based entirely on primary data in the form of semi-structured interviews with experts from different units of the Finnish music industry value chain. Since the study offers assessment of diverse viewpoints on the value chain, it further provides an integrated picture of the Finnish music industry current situation and its competitive environment. The results suggest that the music industry is currently in a turbulent stage of experimentation with new business models and digital innovations. However, at this point it is impossible to determine which business model will be approved by the consumers in the longer run. Nevertheless, the study confirmed the claim that consumption of music in its digital form is to become dominant over the traditional physical copies sales in the nearest future. As a result the music industry is becoming more user-oriented; that is the focus is shifting from music production towards artist branding and management and visibility to the audience. Furthermore, the music industry is undergoing the process of integration with other industries such as media, social networks, internet services providers and mobile phone manufacturers in order to better fulfill the consumers’ needs. The previously underrated live music and merchandising are also increasing their significance for the revenues in the stagnant music markets. Therefore, the music industry is developing at present towards becoming an integrated entertainment industry deeply penetrating every point of modern people’s leisure activities.

The Application of Enterprise Architecture Approach to Military Concept Development–Case Study

Abstract—Concept development and experimentation (CD&E) plays an important role in driving strategic transformation in the military community. Defence architecture frameworks, such as the NATO architecture framework, are considered excellent means to support CD&E. There is not much empirical evidence, however, to indicate how enterprise architectures (EA) are applied in the military community or particularly in military CD&E. Consequently, this paper describes and discusses empirical application of the EA approach in CD&E. The research method in the paper is a case study. Situational method engineering (SiME) is used as a framework to adapt the EA approach to the case project of the paper. The findings of the paper suggest that the EA is applicable to CD&E work, although all aspects of the original concept could not be expressed in the EA model of the case project. The results also show that the SiME method can support in applying the EA framework to the CD&E in the case project.

Situational awareness concept in a multinational collaboration environment : challenges in the information sharing framework

Technological capabilities are built to support different types of collaboration, and this gives the justification to widely observe, how activity environments are influenced by technology. Technology as an enabler can be addressed from different perspectives, other than merely technological. Dynamic, evolving environment is at the same time interesting but also challenging. As a multinational collaboration environment, the maritime surveillance is an good example of time critical and evolving environment, where technological solutions enable new ways of collaboration. Justification for the inspiration to use maritime environment as the baseline for understanding the challenges in creating and maintaining adequate level of situational awareness, derives from the complexity of the collaboration and information sharing environment elements, needed to be taken into account, when analyzing criticalities related to decision making. Situational awareness is an important element supporting decision making, and challenges related to it can also be observed in the maritime environment. This dissertation describes the structures and factors involved in this complex setting, found from the case studies that should be taken into account when trying to understand, how these elements affect the activities. This dissertation focuses on the gray area that is between a life threatening situation and normal everyday activities. From the multinational experimentation series case studies, MNE5 and MNE6 it was possible to observe situations that were not life threatening for the participants themselves, but not also basic every day activities. These case studies provided a unique possibility to see situations, where gaining of situational awareness and decision making are challenged with time critical crisis situations. Unfortunately organizations do not normally take the benefit from the everyday work to prepare themselves for possible emerging crisis situations. This dissertation focuses on creating a conceptual model and a concept that supports organizations – also outside the maritime community – to improve their ability to support gaining of situational awareness from the individual training level, all the way to changes in organizational structures in aiming for better support for decision making from the individual level to the highest decision making level. Quick changes and unpredictability are reality in organizations and organizations do not have the possibility to control all the factors that affect their functioning. Since we cannot be prepared for everything, and predict every crisis, individual activities inside teams and as a part of organizations, need to be supported with guidance, tools and training in order to support acting in challenging situations. In fact the ideology of the conceptual model created, lies especially in the aim of not controlling everything in beforehand, but supporting organizations with concrete procedures to help individuals to react in different, unpredictable situations, instead of focusing on traditional risk prevention and management. Technological capabilities are not automatically solutions for functional challenges; this is why it is justified to broaden the problem area observation from the technological perspective. This dissertation demonstrates that it is possible to support collaboration in a multinational environment with technological solutions, but it requires the recognition of technological limitations and accepting the possible restrictions related to technological innovations. Technology should not be considered value per se, the value of technology should be defined according to the support of activities, including strategic and operational environment evaluation, identification of organizational elements, and taking into account also the social factors and their challenges. Then we are one step closer to providing technological solutions that support the actual activities by taking into account the variables of the activity environment in question. The multidisciplinary view to approach the information sharing and collaboration framework, is derived especially from the complexity of decision making and building of situational awareness, since they are not build or created in vacuity, but in the organizational framework by the people doing it with the technological capabilities, enabled by the organizational structures. Introduced case studies were related to maritime environment, but according to the research results, it is valid to argue, that based on the lessons learned it is possible to create and further develop conceptual model and to create a general concept to support a wider range of organizations in their attempt to gain better level of situational awareness (SA) and to support decision making. To proof the versatile usage of the developed concept, I have introduced the case study findings to the health care environment and reflected the identified elements from the trauma center to the created concept. The main contribution to complete this adventure is the presented situational awareness concept created in the respect to NATO concept structure. This has been done to tackle the challenge of collaboration by focusing on situational awareness in the information sharing context by providing a theoretical ground and understanding, of how these issues should be approached, and how these elements can be generalized and used to support activities in other environments as well. This dissertation research has been a several year evolving process reflecting and affecting presented case studies and this learning experience from the case studies has also affected the goals and research questions of this dissertation. This venture has been written from a retro perspective according to ideology of process modeling and design rationale to present to the reader how this entire journey took place and what where the critical milestones that affected the end result, conceptual model. Support in a challenging information sharing framework can be provided with the right type of combination of tools, procedures and individual effort. This dissertation will provide insights to those with a new approach to war technology for the organizations to gain a better level of awareness and to improve the capabilities in decision making. This dissertation will present, from the war technology starting point, a new approach and possibility for the organizations to create a better level of awareness and support for decision making with the right combination of tools, procedures and individual effort.

Enhancing the development of military capabilities by a systems approach

The political environment of security and defence has changed radically in the Western industrialised world since the Cold War. As a response to these changes, since the beginning of the twenty-first century, most Western countries have adopted a ‘capabilities-based approach’ to developing and operating their armed forces. More responsive and versatile military capabilities must be developed to meet the contemporary challenges. The systems approach is seen as a beneficial means of overcoming traps in resolving complex real -world issues by conventional thinking. The main objectives of this dissertation are to explore and assess the means to enhance the development of military capabilities both in concept development and experimentation (CD&E) and in national defence materiel collaboration issues. This research provides a unique perspective, a systems approach, to the development areas of concern in resolving complex real-world issues. This dissertation seeks to increase the understanding of the military capability concept both as a whole and with in its life cycle. The dissertation follows the generic functionalist systems methodology by Jackson. The methodology applies a comprehensive set of constitutive rules to examine the research objectives. This dissertation makes contribution to current studies about military capability. It presents two interdepen dent conceptual capability models: the comprehensive capability meta-model (CCMM) and the holistic capability life cycle model (HCLCM). These models holistically and systematically complement the existing, but still evolving, understanding of military capability and its life cycle. In addition, this dissertation contributes to the scientific discussion of defence procurement in its broad meaning by introducing the holistic model about the national defence materiel collaboration between the defence forces, defence industry and academia. The model connects the key collaborative mechanisms, which currently work in isolation from each other, and take into consideration the unique needs of each partner. This dissertation contributes empirical evidence regarding the benefits of enterprise architectures (EA) to CD&E. The EA approach may add value to traditional concept development by increasing the clarity, consistency and completeness of the concept. The most important use considered for EA in CD&E is that it enables further utilisation of the concept created in the case project.

The early activities of front end of innovation in oem companies using a new fei platform as a framework for renewal

The main goal of this study is to create a seamless chain of actions and more detailed structure to the front end of innovation to be able to increase the front end performance and finally to influence the renewal of companies. The main goal is achieved through by the new concept of an integrated model of early activities of FEI leading to a discovery of new elements of opportunities and the identification of new business and growth areas. The procedure offers one possible solution to a dynamic strategy formation process in innovation development cycle. In this study the front end of innovation is positioned between a strategy reviews and a concept creation with needed procedures, tools, and frameworks. The starting point of the study is that the origins of innovation are not well enough understood. The study focuses attention on the early activities of FEI. These first activities are conceptualized in order to find out successful innovation initiatives and strategic renewal agendas. A seamless chain of activities resulting in faster and more precise identification of opportunities and growth areas available on markets and inside companies is needed. Three case studies were conducted in order to study company views on available theory doctrine and to identify the first practical experiences and procedures in the beginning of the front end of innovation. Successful innovation requires focus on renewal in both internal and external directions and they should be carefully balanced for best results. Instead of inside-out mode of actions the studied companies have a strong outside-in thinking mode and they mainly co-develop their innovation initiatives in close proximity with customers i.e. successful companies are an integral part of customers business and success. Companies have tailor-made innovation processes combined their way of working linked to their business goals, and priorities of actual needs of transformation. The result of this study is a new modular FEI platform which can be configured by companies against their actual business needs and drivers. This platform includes new elements of FEI documenting an architecture presenting how the system components work together. The system is a conceptual approach from theories of emergent strategy formation, opportunity identification and creation, interpretation-analysis-experimentation triad and the present FEI theories. The platform includes new features compared to actual models of FEI. It allows managers to better understand the importance of FEI in the whole innovation development stage and FEI as a phase and procedure to discover and implement emergent strategy. An adaptable company rethinks and redirects strategy proactively from time to time. Different parts of the business model are changed to remove identified obstacles for growth and renewal which gives them avenues to find right reforms for renewal.