Sosiaalisten ongelmien retoriikkaa : tapaus doping

Summary: Rhetoric in discussing social problems: The case of doping

Electrochemical Characterisation of Filter Media Properties and Their Exploitation in Enhanced Filtration

Streaming potential measurements for the surface charge characterisation of different filter media types and materials were used. The equipment was developed further so that measurements could be taken along the surfaces, and so that tubular membranes could also be measured. The streaming potential proved to be a very useful tool in the charge analysis of both clean and fouled filter media. Adsorption and fouling could be studied, as could flux, as functions of time. A module to determine the membrane potential was also constructed. The results collected from the experiments conducted with these devices were used in the study of the theory of streaming potential as an electrokinetic phenomenon. Several correction factors, which are derived to take into account the surface conductance and the electrokinetic flow in very narrow capillaries, were tested in practice. The surface materials were studied using FTIR and the results compared with those from the streaming potentials. FTIR analysis was also found to be a useful tool in the characterisation of filters, as well as in the fouling studies. Upon examination of the recorded spectra from different depths in a sample it was possible to determine the adsorption sites. The influence of an external electric field on the cross flow microflltration of a binary protein system was investigated using a membrane electroflltration apparatus. The results showed that a significant improvement could be achieved in membrane filtration by using the measured electrochemical properties to help adjust the process conditions.

Electrochemical and spectroelectrochemical characterization of alkylated and thiolated polyanilines

Vi omges i vardagen av alla sorters plaster, som kemiskt kallas för polymerer. Vi anknyter dem oftast till vardagliga föremål såsom muggar, leksaker eller platskassar. Det finns dock en särklass av polymerer som fås elektriskt ledande genom en så kallad dopningsprocess. Dopning innebär i detta fall oxidation eller reduktion av konjugerade dubbelbindningar i polymerstrukturen. Detta har lett till utveckling av elektriska apparater där dyra, och i vissa fall även sällsynta, metall och halvledarmaterial ersätts genom av elektriskt ledande polymerer (plaster). Utöver elektronisk ledningsförmåga uppvisar dessa polymerer också jonisk ledningsförmåga. Denna kombination av unika egenskaper möjliggör skapandet av t.ex. nya sensormaterial som kan överföra kemisk information till en mätbar elektronisk signal. Detta öppnar i sin tur möjligheter att göra snabba, billiga och känsliga sensorer för bl.a. mediciniska analyser. I denna avhandling karakteriserades elektrokemiskt och spektroelektrokemiskt N- och ring-substituerade polyanilinfilmer. Polyanilin (PANI) hör till de mest studerade elektriskt ledande polymererna. Den är stabil och lätt att framställa. Substituerade polyaniliner har ändå studerats måttligt, mest p.g.a. att substituerade PANIs ledningsförmåga är lägre än PANIs och deras framställning kan vara svår. De nya grupperna i PANI-kedjan ger dock en möjlighet att binda ytterligare molekyler av intresse till PANI-kedjan, som t.ex. jonselektiva grupper. Kovalent bundna selektiva molekyler ger upphov till stabila, känsliga och selektiva sensormaterial. Karakteriseringen av de studerade polymerer är viktig för den fundamentala förståelsen av deras unika egenskaper och för utvecklingen av framtidens sensormaterial. -------------------------------------- Käytämme joka päivä monenlaisia muoveja, joita kutsutaan kemiassa myös polymeereiksi. Olemme tottuneet yhdistämään muovit arkisiin esineisiin kuten mukeihin, leluihin tai muovikasseihin. On kuitenkin olemassa erityisiä polymeerejä, jotka voidaan saada sähköä johtaviksi hapetus- ja pelkistysreaktioiden avulla. Tästä johtuen on kehitteillä sähköisiä laitteita, joissa kalliit ja jossain tapauksissa myös harvinaisia metalleja sisältävät osat ja puolijohteet voidaan korvata johdepolymeereillä (eli muoveilla). Sähkönjohtavuuden lisäksi johdepolymeereillä on myös ionijohtavuutta. Näiden erityislaatuisten ominaisuuksien yhdistelmä on mahdollistanut mm. sensorimateriaalin kehittämisen, sillä kemiallinen tieto voidaan kääntää mitattavaksi sähköiseksi signaaliksi. Tämä taas omalta osaltaan mahdollistaisi nopeiden, halpojen ja herkkien sensorien valmistuksen, mm. diagnostiikkaan. Tässä väitöksessä on tutkittu sähkökemiallisesti valmistettuja N- ja rengassubstituoituja polyaniliinikalvoja. Polyaniliini (PANI) on yksi eniten tutkituista johdepolymeereistä. Se on stabiili ja helppo valmistaa. Substituoidut polyaniliinit ovat herättäneet vain kohtalaista tieteellistä kiinnostusta, lähinnä, koska niiden sähköinen johdekyky on alhaisempi kuin PANIn. Myös niiden valmistus voi olla vaikeaa. Substituoidut molekyylit PANI-ketjussa mahdollistavat kuitenkin, että niihin voi liittää uusia molekyylejä, esim. ioniherkkiä ryhmiä. Kovalentisti sitoutuneilla selektiivisillä molekyyleillä saadaan tehtyä stabiileja, herkkiä ja selektiivisiä sensorimateriaaleja. Väitöksessä käytettyjen polymeerien karakterisointi on tärkeää, jotta niiden erityisominaisuuksia pystyttäisiin ymmärtämään paremmin ja myös kehittämään sopivia tulevaisuuden sensorimateriaaleja.

Electrochemical Treatment of Wastewaters

Electrocoagulation is a process in which wastewater is treated under electrical current. Coagulant is formed during the process through the metal anode dissolution to respective ions which react with hydroxyl ions released in cathode. These metal hydroxides form complexes with pollutant ions. Pollutants are removed among metal hydroxide precipitates. This study was concentrated on describing chemistry and device structures in which electrochemical treatment operations are based on. Studied pollutants were nitrogen compounds, sulphate, trivalent and pentavalent arsenic, heavy metals, phosphate, fluoride, chloride, and bromide. In experimental part, removal of ammonium, nitrate, and sulphate during electrochemical treatment was studied separately. Main objective of this study was to find suitable metal plate material for ammonium, nitrate, and sulphate removal, respectively. Also other parameters such as pH of solution, concentration of pollutant and sodium chloride, and current density were optimized. According to this study the most suitable material for ammonium and sulphate removal by electrochemical treatment was stainless steel. Respectively, iron was the optimum material for nitrate removal. Rise in the pH of solution at the final stage of electrochemical treatment of ammonium, nitrate, and sulphate was detected. Conductivities of solutions decreased during ammonium removal in electrochemical processes. When nitrate and sulphate were removed electrochemically conductivities of solutions increased. Concentrations of residual metals in electrochemically treated solutions were not significant. Based on this study electrochemical treatment processes are recommended to be used in treatment of industrial wastewaters. Treatment conditions should be optimized for each wastewater matrix.

Synthesis, characterization and chemical sensor application of conducting polymers

Polymeric materials that conduct electricity are highly interesting for fundamental studies and beneficial for modern applications in e.g. solar cells, organic field effect transistors (OFETs) as well as in chemical and bio‐sensing. Therefore, it is important to characterize this class of materials with a wide variety of methods. This work summarizes the use of electrochemistry also in combination with spectroscopic methods in synthesis and characterization of electrically conducting polymers and other π‐conjugated systems. The materials studied in this work are intended for organic electronic devices and chemical sensors. Additionally, an important part of the presented work, concerns rational approaches to the development of water‐based inks containing conducting particles. Electrochemical synthesis and electroactivity of conducting polymers can be greatly enhanced in room temperature ionic liquids (RTILs) in comparison to conventional electrolytes. Therefore, poly(para‐phyenylene) (PPP) was electrochemically synthesized in the two representative RTILs: bmimPF6 and bmiTf2N (imidazolium and pyrrolidinium‐based salts, respectively). It was found that the electrochemical synthesis of PPP was significantly enhanced in bmimPF6. Additionally, the results from doping studies of PPP films indicate improved electroactivity in bmimPF6 during oxidation (p‐doping) and in bmiTf2N in the case of reduction (n‐doping). These findings were supported by in situ infrared spectroscopy studies. Conducting poly(benzimidazobenzophenanthroline) (BBL) is a material which can provide relatively high field‐effect mobility of charge carriers in OFET devices. The main disadvantage of this n‐type semiconductor is its limited processability. Therefore in this work BBL was functionalized with poly(ethylene oxide) PEO, varying the length of side chains enabling water dispersions of the studied polymer. It was found that functionalization did not distract the electrochemical activity of the BBL backbone while the processability was improved significantly in comparison to conventional BBL. Another objective was to study highly processable poly(3,4‐ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT:PSS) water‐based inks for controlled patterning scaled‐down to nearly a nanodomain with the intention to fabricate various chemical sensors. Developed PEDOT:PSS inks greatly improved printing of nanoarrays and with further modification with quaternary ammonium cations enabled fabrication of PEDOT:PSS‐based chemical sensors for lead (II) ions with enhanced adhesion and stability in aqueous environments. This opens new possibilities for development of PEDOT:PSS films that can be used in bio‐related applications. Polycyclic aromatic hydrocarbons (PAHs) are a broad group of π‐conjugated materials consisting of aromatic rings in the range from naphthalene to even hundred rings in one molecule. The research on this type of materials is intriguing, due to their interesting optical properties and resemblance of graphene. The objective was to use electrochemical synthesis to yield relatively large PAHs and fabricate electroactive films that could be used as template material in chemical sensors. Spectroscopic, electrochemical and electrical investigations evidence formation of highly stable films with fast redox response, consisting of molecules with 40 to 60 carbon atoms. Additionally, this approach in synthesis, starting from relatively small PAH molecules was successfully used in chemical sensor for lead (II).

Solid-state reference and ion-selective electrodes : towards portable potentiometric sensing

Potentiometric sensors are very attractive tools for chemical analysis because of their simplicity, low power consumption and low cost. They are extensively used in clinical diagnostics and in environmental monitoring. Modern applications of both fields require improvements in the conventional construction and in the performance of the potentiometric sensors, as the trends are towards portable, on-site diagnostics and autonomous sensing in remote locations. The aim of this PhD work was to improve some of the sensor properties that currently hamper the implementation of the potentiometric sensors in modern applications. The first part of the work was concentrated on the development of a solid-state reference electrode (RE) compatible with already existing solid-contact ion-selective electrodes (ISE), both of which are needed for all-solid-state potentiometric sensing systems. A poly(vinyl chloride) membrane doped with a moderately lipophilic salt, tetrabutylammonium-tetrabutylborate (TBA-TBB), was found to show a satisfactory stability of potential in sample solutions with different concentrations. Its response time was nevertheless slow, as it required several minutes to reach the equilibrium. The TBA-TBB membrane RE worked well together with solid-state ISEs in several different situations and on different substrates enabling a miniature design. Solid contacts (SC) that mediate the ion-to-electron transduction are crucial components of well-functioning potentiometric sensors. This transduction process converting the ionic conduction of an ion-selective membrane to the electronic conduction in the circuit was studied with the help of electrochemical impedance spectroscopy (EIS). The solid contacts studied were (i) the conducting polymer (CP) poly(3,4-ethylienedioxythiophene) (PEDOT) and (ii) a carbon cloth having a high surface area. The PEDOT films were doped with a large immobile anion poly(styrene sulfonate) (PSS-) or with a small mobile anion Cl-. As could be expected, the studied PEDOT solid-contact mediated the ion-toelectron transduction more efficiently than the bare glassy carbon substrate, onto which they were electropolymerized, while the impedance of the PEDOT films depended on the mobility of the doping ion and on the ions in the electrolyte. The carbon cloth was found to be an even more effective ion-to-electron transducer than the PEDOT films and it also proved to work as a combined electrical conductor and solid contact when covered with an ion-selective membrane or with a TBA-TBB-based reference membrane. The last part of the work was focused on improving the reproducibility and the potential stability of the SC-ISEs, a problem that culminates to the stability of the standard potential E°. It was proven that the E° of a SC-ISE with a conducting polymer as a solid contact could be adjusted by reducing or oxidizing the CP solid contact by applying current pulses or a potential to it, as the redox state of the CP solid-contact influences the overall potential of the ISE. The slope and thus the analytical performance of the SC-ISEs were retained despite the adjustment of the E°. The shortcircuiting of the SC-ISE with a conventional large-capacitance RE was found to be a feasible instrument-free method to control the E°. With this method, the driving force for the oxidation/reduction of the CP was the potential difference between the RE and the SC-ISE, and the position of the adjusted potential could be controlled by choosing a suitable concentration for the short-circuiting electrolyte. The piece-to-piece reproducibility of the adjusted potential was promising, and the day-today reproducibility for a specific sensor was excellent. The instrumentfree approach to control the E° is very attractive considering practical applications.