Experimental and discrete element simulation studies of bell-less charging of blast furnace

This thesis presents an experimental study and numerical study, based on the discrete element method (DEM), of bell-less charging in the blast furnace. The numerical models are based on the microscopic interaction between the particles in the blast furnace charging process. The emphasis is put on model validation, investigating several phenomena in the charging process, and on finding factors that influence the results. The study considers and simulates size segregation in the hopper discharging process, particle flow and behavior on the chute, which is the key equipment in the charging system, using mono-size spherical particles, multi-size spheres and nonspherical particles. The behavior of the particles at the burden surface and pellet percolation into a coke layer is also studied. Small-scale experiments are used to validate the DEM models.

Development of an HTR-10 model in the Serpent reactor physics code

The use of exact coordinates of pebbles and fuel particles of pebble bed reactor modelling becoming possible in Monte Carlo reactor physics calculations is an important development step. This allows exact modelling of pebble bed reactors with realistic pebble beds without the placing of pebbles in regular lattices. In this study the multiplication coefficient of the HTR-10 pebble bed reactor is calculated with the Serpent reactor physics code and, using this multiplication coefficient, the amount of pebbles required for the critical load of the reactor. The multiplication coefficient is calculated using pebble beds produced with the discrete element method and three different material libraries in order to compare the results. The received results are lower than those from measured at the experimental reactor and somewhat lower than those gained with other codes in earlier studies.

Application and development of numerical methods for the modelling of innovative gas cooled fission reactors

Innovative gas cooled reactors, such as the pebble bed reactor (PBR) and the gas cooled fast reactor (GFR) offer higher efficiency and new application areas for nuclear energy. Numerical methods were applied and developed to analyse the specific features of these reactor types with fully three dimensional calculation models. In the first part of this thesis, discrete element method (DEM) was used for a physically realistic modelling of the packing of fuel pebbles in PBR geometries and methods were developed for utilising the DEM results in subsequent reactor physics and thermal-hydraulics calculations. In the second part, the flow and heat transfer for a single gas cooled fuel rod of a GFR were investigated with computational fluid dynamics (CFD) methods. An in-house DEM implementation was validated and used for packing simulations, in which the effect of several parameters on the resulting average packing density was investigated. The restitution coefficient was found out to have the most significant effect. The results can be utilised in further work to obtain a pebble bed with a specific packing density. The packing structures of selected pebble beds were also analysed in detail and local variations in the packing density were observed, which should be taken into account especially in the reactor core thermal-hydraulic analyses. Two open source DEM codes were used to produce stochastic pebble bed configurations to add realism and improve the accuracy of criticality calculations performed with the Monte Carlo reactor physics code Serpent. Russian ASTRA criticality experiments were calculated. Pebble beds corresponding to the experimental specifications within measurement uncertainties were produced in DEM simulations and successfully exported into the subsequent reactor physics analysis. With the developed approach, two typical issues in Monte Carlo reactor physics calculations of pebble bed geometries were avoided. A novel method was developed and implemented as a MATLAB code to calculate porosities in the cells of a CFD calculation mesh constructed over a pebble bed obtained from DEM simulations. The code was further developed to distribute power and temperature data accurately between discrete based reactor physics and continuum based thermal-hydraulics models to enable coupled reactor core calculations. The developed method was also found useful for analysing sphere packings in general. CFD calculations were performed to investigate the pressure losses and heat transfer in three dimensional air cooled smooth and rib roughened rod geometries, housed inside a hexagonal flow channel representing a sub-channel of a single fuel rod of a GFR. The CFD geometry represented the test section of the L-STAR experimental facility at Karlsruhe Institute of Technology and the calculation results were compared to the corresponding experimental results. Knowledge was gained of the adequacy of various turbulence models and of the modelling requirements and issues related to the specific application. The obtained pressure loss results were in a relatively good agreement with the experimental data. Heat transfer in the smooth rod geometry was somewhat under predicted, which can partly be explained by unaccounted heat losses and uncertainties. In the rib roughened geometry heat transfer was severely under predicted by the used realisable k − epsilon turbulence model. An additional calculation with a v2 − f turbulence model showed significant improvement in the heat transfer results, which is most likely due to the better performance of the model in separated flow problems. Further investigations are suggested before using CFD to make conclusions of the heat transfer performance of rib roughened GFR fuel rod geometries. It is suggested that the viewpoints of numerical modelling are included in the planning of experiments to ease the challenging model construction and simulations and to avoid introducing additional sources of uncertainties. To facilitate the use of advanced calculation approaches, multi-physical aspects in experiments should also be considered and documented in a reasonable detail.

Modeling of burden distribution in the blast furnace

The blast furnace is the main ironmaking production unit in the world which converts iron ore with coke and hot blast into liquid iron, hot metal, which is used for steelmaking. The furnace acts as a counter-current reactor charged with layers of raw material of very different gas permeability. The arrangement of these layers, or burden distribution, is the most important factor influencing the gas flow conditions inside the furnace, which dictate the efficiency of the heat transfer and reduction processes. For proper control the furnace operators should know the overall conditions in the furnace and be able to predict how control actions affect the state of the furnace. However, due to high temperatures and pressure, hostile atmosphere and mechanical wear it is very difficult to measure internal variables. Instead, the operators have to rely extensively on measurements obtained at the boundaries of the furnace and make their decisions on the basis of heuristic rules and results from mathematical models. It is particularly difficult to understand the distribution of the burden materials because of the complex behavior of the particulate materials during charging. The aim of this doctoral thesis is to clarify some aspects of burden distribution and to develop tools that can aid the decision-making process in the control of the burden and gas distribution in the blast furnace. A relatively simple mathematical model was created for simulation of the distribution of the burden material with a bell-less top charging system. The model developed is fast and it can therefore be used by the operators to gain understanding of the formation of layers for different charging programs. The results were verified by findings from charging experiments using a small-scale charging rig at the laboratory. A basic gas flow model was developed which utilized the results of the burden distribution model to estimate the gas permeability of the upper part of the blast furnace. This combined formulation for gas and burden distribution made it possible to implement a search for the best combination of charging parameters to achieve a target gas temperature distribution. As this mathematical task is discontinuous and non-differentiable, a genetic algorithm was applied to solve the optimization problem. It was demonstrated that the method was able to evolve optimal charging programs that fulfilled the target conditions. Even though the burden distribution model provides information about the layer structure, it neglects some effects which influence the results, such as mixed layer formation and coke collapse. A more accurate numerical method for studying particle mechanics, the Discrete Element Method (DEM), was used to study some aspects of the charging process more closely. Model charging programs were simulated using DEM and compared with the results from small-scale experiments. The mixed layer was defined and the voidage of mixed layers was estimated. The mixed layer was found to have about 12% less voidage than layers of the individual burden components. Finally, a model for predicting the extent of coke collapse when heavier pellets are charged over a layer of lighter coke particles was formulated based on slope stability theory, and was used to update the coke layer distribution after charging in the mathematical model. In designing this revision, results from DEM simulations and charging experiments for some charging programs were used. The findings from the coke collapse analysis can be used to design charging programs with more stable coke layers.

Siltanosturin teräsrakenteen suunnittelun avuksi luodun ohjelman jatkokehitys

Diplomityössä tehdään jatkokehitystä KCI Konecranes yrityksen siltanosturin laskentaohjelmaan. Ohjelman tärkeimmät jatkokehityskohteet kartoitettiin käyttäjäkyselyn avulla ja niistä valittiin toivotuimmat, sekä diplomityön lujuusopilliseen aihepiiriin parhaiten soveltuvat. Työhön valitut kaksi aihetta ovat koteloprofiilin kaksiosaisen uuman lujuuslaskennan selvittäminen ja siltanosturin kahdeksanpyöräisenpäätykannattajan elementtimallin suunnittelu. Diplomityössä selvitetään jatkokehityskohteisiin liittyvä teoria, mutta varsinainen ohjelmointi jätetään työn ulkopuolelle. Kaksiosaisella uumalla varustetussa koteloprofiilissa nostovaunun kulkukiskon alla olevan uuman yläosa tehdään paksummaksi, jotta uuma kestäisi nostovaunun pyöräkuormasta aiheutuvan paikallisen jännityksen, eliniin sanotun rusennusjännityksen. Rusennusjännityksen määrittäminen uumalevyissä on kaksiosaisen uuman lujuuslaskennan tärkein tehtävä. Rusennuksen aiheuttamankalvojännityksen ja jännityskeskittymien määrittämiseen erilaisissa konstruktioissa etsittiin sopivimmat menetelmät kirjallisuudesta ja standardeista. Kalvojännitys voidaan määrittää luotettavasti käyttäen joko 45 asteen sääntöä tai standardin mukaista menetelmää ja jännityskonsentraatioiden suuruus saadaan kertomallakalvojännitys jännityskonsentraatiokertoimilla. Menetelmien toimivuus verifioitiin tekemällä kymmeniä uuman elementtimalleja erilaisin dimensioin ja reunaehdoin ja vertaamalla elementtimallien tuloksia käsin laskettuihin. Käsin lasketut jännitykset saatiin vastaamaan tarkasti elementtimallien tuloksia. Kaksiosaisen uuman lommahdus- ja väsymislaskentaa tutkittiin alustavasti. Kahdeksanpyöräisiä päätykannattajia käytetään suurissa siltanostureissa pienentämään pyöräkuormia ja radan rusennusjännityksiä. Kahdeksanpyöräiselle siltanosturin päätykannattajalle suunniteltiin elementtimallit molempiin rakenteesta käytettyihin konstruktioihin: nivelöityyn ja jäykkäkehäiseen malliin. Elementtimallien rakentamisessa hyödynnettiin jo olemassa olevia malleja, jolloin niiden lisääminen ohjelmakoodiin nopeutuu ja ne ovat varmasti yhteensopivia muiden laskentamoduuleiden kanssa. Elementtimallien värähtelyanalyysin reunaehtoja tarkasteltiin. Värähtelyanalyysin reunaehtoihin ei tutkimuksen perusteella tarvitse tehdä muutoksia, mutta staattisen analyysin reunaehdot kaipaavat vielä lisätutkimusta.

Dynamic Simulations of Rotors during Drop on Retainer Bearings

The active magnetic bearings have recently been intensively developed because of noncontact support having several advantages compared to conventional bearings. Due to improved materials, strategies of control, and electrical components, the performance and reliability of the active magnetic bearings are improving. However, additional bearings, retainer bearings, still have a vital role in the applications of the active magnetic bearings. The most crucial moment when the retainer bearings are needed is when the rotor drops from the active magnetic bearings on the retainer bearings due to component or power failure. Without appropriate knowledge of the retainer bearings, there is a chance that an active magnetic bearing supported rotor system will be fatal in a drop-down situation. This study introduces a detailed simulation model of a rotor system in order to describe a rotor drop-down situation on the retainer bearings. The introduced simulation model couples a finite element model with component mode synthesis and detailed bearing models. In this study, electrical components and electromechanical forces are not in the focus. The research looks at the theoretical background of the finite element method with component mode synthesis that can be used in the dynamic analysis of flexible rotors. The retainer bearings are described by using two ball bearing models, which include damping and stiffness properties, oil film, inertia of rolling elements and friction between races and rolling elements. Thefirst bearing model assumes that the cage of the bearing is ideal and that the cage holds the balls in their predefined positions precisely. The second bearing model is an extension of the first model and describes the behavior of the cageless bearing. In the bearing model, each ball is described by using two degrees of freedom. The models introduced in this study are verified with a corresponding actual structure. By using verified bearing models, the effects of the parameters of the rotor system onits dynamics during emergency stops are examined. As shown in this study, the misalignment of the retainer bearings has a significant influence on the behavior of the rotor system in a drop-down situation. In this study, a stability map of the rotor system as a function of rotational speed of the rotor and the misalignment of the retainer bearings is presented. In addition, the effects of parameters of the simulation procedure and the rotor system on the dynamics of system are studied.

A novel procedure for establishing clinching parameters for high strength steel sheet

The building industry has a particular interest in using clinching as a joining method for frame constructions of light-frame housing. Normally many clinch joints are required in joining of frames.In order to maximise the strength of the complete assembly, each clinch joint must be as sound as possible. Experimental testing is the main means of optimising a particular clinch joint. This includes shear strength testing and visual observation of joint cross-sections. The manufacturers of clinching equipment normally perform such experimental trials. Finite element analysis can also be used to optimise the tool geometry and the process parameter, X, which represents the thickness of the base of the joint. However, such procedures require dedicated software, a skilled operator, and test specimens in order to verify the finite element model. In addition, when using current technology several hours' computing time may be necessary. The objective of the study was to develop a simple calculation procedure for rapidly establishing an optimum value for the parameter X for a given tool combination. It should be possible to use the procedure on a daily basis, without stringent demands on the skill of the operator or the equipment. It is also desirable that the procedure would significantly decrease thenumber of shear strength tests required for verification. The experimental workinvolved tests in order to obtain an understanding of the behaviour of the sheets during clinching. The most notable observation concerned the stage of the process in which the upper sheet was initially bent, after which the deformation mechanism changed to shearing and elongation. The amount of deformation was measured relative to the original location of the upper sheet, and characterised as the C-measure. By understanding in detail the behaviour of the upper sheet, it waspossible to estimate a bending line function for the surface of the upper sheet. A procedure was developed, which makes it possible to estimate the process parameter X for each tool combination with a fixed die. The procedure is based on equating the volume of material on the punch side with the volume of the die. Detailed information concerning the behaviour of material on the punch side is required, assuming that the volume of die does not change during the process. The procedure was applied to shear strength testing of a sample material. The sample material was continuously hot-dip zinc-coated high-strength constructional steel,with a nominal thickness of 1.0 mm. The minimum Rp0.2 proof stress was 637 N/mm2. Such material has not yet been used extensively in light-frame housing, and little has been published on clinching of the material. The performance of the material is therefore of particular interest. Companies that use clinching on a daily basis stand to gain the greatest benefit from the procedure. By understanding the behaviour of sheets in different cases, it is possible to use data at an early stage for adjusting and optimising the process. In particular, the functionality of common tools can be increased since it is possible to characterise the complete range of existing tools. The study increases and broadens the amount ofbasic information concerning the clinching process. New approaches and points of view are presented and used for generating new knowledge.

Maastoajoneuvon korin teräsrakenteiden värähtelyominaisuuksien FEM-analysointimenetelmien kehittäminen

Tämä diplomityö on tehty Patria Vehicles Oy:n toimeksiannosta. Patria Vehicles Oy:n tuotantoon kuuluvat vaativiin maasto-olosuhteisiin soveltuvat sotilasajoneuvot. Tutkimuksen tarkoituksena oli kehittää menetelmäohjeet, kuinka FEM-analyysillä voidaan tutkia tuotekehitysvaiheessa ajoneuvon korin teräsrakenteiden värähtelyominaisuuksia ja dynaamista käyttäytymistä. Tutkimuksessa on käytetty Ideas-FEM-ohjelmistoa. Dynaamisten ongelmien ratkaisemiseksi on ymmärrettävä rakenteiden dynaamista käyttäytymistä. Rakenteiden käyttäytymistä ja muodonmuutoksia on tutkittava kriittisillä ominaistaajuuksilla. Tutkimuksessa on selvitetty, kuinka ajoneuvon elementtimallilla voidaan tehdä ominaisvärähtely- ja vastelaskentaa. Ominaisvärähtelylaskennalla selvitetään rakenteen ominaismuodot ja -taajuudet. Vastelaskennalla tutkitaan erilaisten herätteiden vaikutuksia ajoneuvon dynaamiseen käyttäytymiseen ja määritetään herätteistä rakenteeseen aiheutuvat vasteet ja herätteiden siirtyvyys rakenteessa. Lisäksi tutkitaan herätteiden aiheuttamia todellisia jännityksiä ja siirtymiä, jotta saadaan selville rakenteen todelliset rasitukset. Analyyseillä voidaan tutkia, kuinka ajoneuvon korirakennetta on jäykistettävä ja vaimennettava, jotta siinä ei esiinny haitallista melua ja värähtelyä.

Virtuaaliprototyypin käyttö roottorin dynamiikan analysoinnissa

Työn tavoitteena oli selvittää kaupallisen dynamiikansimulointiohjelmiston soveltuvuus roottoridynamiikan analysointiin. Työssä keskityttiin erityisesti roottorin dynamiikkaan vaikuttavien epäideaalisuuksien mallintamiseen. Simulointitulosten tarkkuutta selvitettiin mittauksilla. Lisäksi vertailtiin yleiskäyttöisen dynamiikan simulointiohjelmiston ja roottoridynamiikan erikoisohjelmiston teoriaa. Tutkittava roottori oli paperikoneen putkitela. Telan joustavuus kuvattiin elementtimenetelmällä ratkaistujen moodien avulla. Elementtimallissa huomioitiin telan vaipan seinämänpaksuusvaihtelu, joka vaikuttaa telan massa- ja jäykkyysjakaumaan. Dynamiikkaohjelmistossa mallinnettiin telan tuennasta tulevat herätteet. Dynamiikkaohjelmistona käytettiin ADAMS:ia ja FEM-ohjelmana ANSYS:stä. Tuloksista havaittiin käytetyn menetelmän soveltuvan roottoridynamiikan analysointiin ja roottorin epäideaalisuuksien mallintamiseen. Simulointimallilla saatiin esille murtolukukriittiset pyörimisnopeudet ja telan kriittinen pyörimisnopeus vastasi hyvin mittaustuloksia.

Paperirullan kannatushihnan kestoiän pidentäminen

Työn tavoitteena oli selvittää kannatushihnapituusleikkurissa paperin rullaukseen käytettävän kannatushihnan kestoikään vaikuttavia tekijöitä ja ratkaisuja liian lyhyeen kestoikään liittyviin ongelmiin. Työssä selvitettiin ensin kannatushihnatyyppisen pituusleikkurin toimintaa ja tarkemmin sen rullausosaa ja rullausprosessin parametreja. Kannatushihnan kestoikään vaikuttavia tekijöitä on käsitelty kirjallisuuden ja kohdeyrityksessä olevan materiaalin perusteella. Seuraavaksi esitettiin ideoita kannatushihnan rakenteesta ja materiaaleista sekä vertailtiin niitä keskenään ja nykyiseen hihnan rakenteeseen. Työssä tehtiin nykyistä kannatushihnaa simuloiva kaksiulotteinen elementtimalli. Tämän elementtimallin mukaan pituusleikkurin telojen suunnassa epätasainen hihnan kuluminen johtuu hihnan paksuussuuntaisten jännitysten eroista. Hihnan kulkua arvioitiin kokeellisesti kahdella erityyppisellä hihnalla. Hihnan kulkuun eniten vaikutti esikiristysvoima, jota pienennettäessä kehänopeusero paperirullaa simuloivan kuormittavan telan ja hihnatelan välillä pieneni. Työssä löydettiin mahdollinen yhteys rullauksessa tulostietona saatavan datan sekä hihnan geometrian välille. Polyeteenivaahtomuovit ovat kitkansa puolesta lupaavia hihnan kitkapinnoitteen materiaaliksi. Toisaalta polyeteenivaahtomuovien mekaanisia ominaisuuksia ei juuri tunneta, eikä niitä ole käytetty kulutuskestoa vaativissa sovelluksissa. Hihnan ulkopinnan kulumismekanismia ei täysin tunneta.

Henkilöauton korin mallintaminen virtuaalitestejä varten

Nykyään auton korien tuotekehitysprosessissa jää hyvin vähän aikaa korin rakenteiden optimointiin. Rakenteiden optimointi tehdään virtuaalitestauksen avulla siten, että yhdellä elementtimallilla tehdään erilaisia testejä ja optimoidaan useita omaisuuksia samanaikaisesti. Tässä tutkimuksessa tavoitteena on kehittää auton korin FEM-malli, jolla voidaan suorittaa mahdollisimman monta erilaista virtuaalitestiä. Rakennetun mallin toimivuutta testattiin tekemällä sille ympäriajoturvallisuustesti ja saatuja tuloksia verrattiin oikean auton testiin.

Kaksoislaatuisesta rakenneputkesta hitsatun X-liitoksen kestävyys ja muodonmuutoskyky

Rautaruukki Oyj:n uusi Ruukki double grade S420MH/S355J2H -rakenneputki yhdistää putkilajien S420MH ja S355J2H ominaisuudet. Eurocode 3:n suunnitteluohjeiden mukaan Ruukki double graden käyttöön on sovellettava lujuusluokan S420 mukaista hitsien mitoitusta ja rakenneputkiliitosten staattista mitoituskestävyyttä alentavaa varmuuskerrointa, kun halutaan hyödyntää lujuusluokan S420 ominaisuudet Ruukki double gradea käytettäessä. Tässä työssä tutkittiin S420-lujuusluokkaa vastaavien suunnittelumääräysten soveltamistarvetta Ruukki double grade -rakenneputken käyttöön. Työn tavoitteena oli arvioida Ruukki double grade -rakenneputkesta hitsaamalla valmistetun X-liitoksen kestävyyden ja muodonmuutoskyvyn riittävyys, kun hitsit mitoitettiin S355-lujuusluokkaa vastaavien Eurocode 3:n suunnitteluohjeiden mukaisesti. X-liitosten kestävyyttä ja muodonmuutoskykyä tutkittiin kokeellisesti -40 C lämpötilassa suoritettujen laboratoriokokeiden avulla sekä analyyttisen laskennan ja elementtimenetelmän keinoin. Kestävyyden riittävyyttä arvioitiin vertaamalla laboratoriokokeista saatuja liitosten kestävyyksiä Eurocode 3:n ja myötöviivateorian mukaisiin kestävyyksiin. Elementtimenetelmän ja laboratoriokokeen pohjalta piirrettyjä liitoksen voima-siirtymäkuvaajia vertailtiin keskenään, kun elementtimalli analysoitiin eri materiaalimalleilla. Lisäksi verrattiin elementtimallin voima-venymäkuvaajia liitoksen venymäliuskan arvoihin. Kaikki koesarjan S355-lujuusluokan mukaisilla hitsin a-mitoilla valmistetut liitokset täyttivät kestävyydelle ja muodonmuutoskyvylle asetetut vaatimukset. Täten tämän koesarjan perusteella ei ollut tarpeellista soveltaa S420-lujuusluokan mukaista hitsien mitoitusta ja staattista mitoituskestävyyttä alentavaa varmuuslukua Ruukki double grade -rakenneputkeen. Elementtimenetelmästä ja laboratoriokokeesta saadut liitoksen voima-siirtymäkuvaajat vastasivat hyvin toisiaan. Sen sijaan elementtimallin voima-venymä-kuvaajat eivät vastanneet venymäliuskojen mittausdataa kovin hyvin.

Simulation of structural stress history based on dynamic analysis

Modern machine structures are often fabricated by welding. From a fatigue point of view, the structural details and especially, the welded details are the most prone to fatigue damage and failure. Design against fatigue requires information on the fatigue resistance of a structure’s critical details and the stress loads that act on each detail. Even though, dynamic simulation of flexible bodies is already current method for analyzing structures, obtaining the stress history of a structural detail during dynamic simulation is a challenging task; especially when the detail has a complex geometry. In particular, analyzing the stress history of every structural detail within a single finite element model can be overwhelming since the amount of nodal degrees of freedom needed in the model may require an impractical amount of computational effort. The purpose of computer simulation is to reduce amount of prototypes and speed up the product development process. Also, to take operator influence into account, real time models, i.e. simplified and computationally efficient models are required. This in turn, requires stress computation to be efficient if it will be performed during dynamic simulation. The research looks back at the theoretical background of multibody dynamic simulation and finite element method to find suitable parts to form a new approach for efficient stress calculation. This study proposes that, the problem of stress calculation during dynamic simulation can be greatly simplified by using a combination of floating frame of reference formulation with modal superposition and a sub-modeling approach. In practice, the proposed approach can be used to efficiently generate the relevant fatigue assessment stress history for a structural detail during or after dynamic simulation. In this work numerical examples are presented to demonstrate the proposed approach in practice. The results show that approach is applicable and can be used as proposed.

Modeling of Liquid-Solid Flow in Industrial Scale

In the present work, liquid-solid flow in industrial scale is modeled using the commercial software of Computational Fluid Dynamics (CFD) ANSYS Fluent 14.5. In literature, there are few studies on liquid-solid flow in industrial scale, but any information about the particular case with modified geometry cannot be found. The aim of this thesis is to describe the strengths and weaknesses of the multiphase models, when a large-scale application is studied within liquid-solid flow, including the boundary-layer characteristics. The results indicate that the selection of the most appropriate multiphase model depends on the flow regime. Thus, careful estimations of the flow regime are recommended to be done before modeling. The computational tool is developed for this purpose during this thesis. The homogeneous multiphase model is valid only for homogeneous suspension, the discrete phase model (DPM) is recommended for homogeneous and heterogeneous suspension where pipe Froude number is greater than 1.0, while the mixture and Eulerian models are able to predict also flow regimes, where pipe Froude number is smaller than 1.0 and particles tend to settle. With increasing material density ratio and decreasing pipe Froude number, the Eulerian model gives the most accurate results, because it does not include simplifications in Navier-Stokes equations like the other models. In addition, the results indicate that the potential location of erosion in the pipe depends on material density ratio. Possible sedimentation of particles can cause erosion and increase pressure drop as well. In the pipe bend, especially secondary flows, perpendicular to the main flow, affect the location of erosion.

Flexible multibody dynamics and intelligent control of a hydraulically driven hybrid redundant robot machine

The assembly and maintenance of the International Thermonuclear Experimental Reactor (ITER) vacuum vessel (VV) is highly challenging since the tasks performed by the robot involve welding, material handling, and machine cutting from inside the VV. The VV is made of stainless steel, which has poor machinability and tends to work harden very rapidly, and all the machining operations need to be carried out from inside of the ITER VV. A general industrial robot cannot be used due to its poor stiffness in the heavy duty machining process, and this will cause many problems, such as poor surface quality, tool damage, low accuracy. Therefore, one of the most suitable options should be a light weight mobile robot which is able to move around inside of the VV and perform different machining tasks by replacing different cutting tools. Reducing the mass of the robot manipulators offers many advantages: reduced material costs, reduced power consumption, the possibility of using smaller actuators, and a higher payload-to-robot weight ratio. Offsetting these advantages, the lighter weight robot is more flexible, which makes it more difficult to control. To achieve good machining surface quality, the tracking of the end effector must be accurate, and an accurate model for a more flexible robot must be constructed. This thesis studies the dynamics and control of a 10 degree-of-freedom (DOF) redundant hybrid robot (4-DOF serial mechanism and 6-DOF 6-UPS hexapod parallel mechanisms) hydraulically driven with flexible rods under the influence of machining forces. Firstly, the flexibility of the bodies is described using the floating frame of reference method (FFRF). A finite element model (FEM) provided the Craig-Bampton (CB) modes needed for the FFRF. A dynamic model of the system of six closed loop mechanisms was assembled using the constrained Lagrange equations and the Lagrange multiplier method. Subsequently, the reaction forces between the parallel and serial parts were used to study the dynamics of the serial robot. A PID control based on position predictions was implemented independently to control the hydraulic cylinders of the robot. Secondly, in machining, to achieve greater end effector trajectory tracking accuracy for surface quality, a robust control of the actuators for the flexible link has to be deduced. This thesis investigates the intelligent control of a hydraulically driven parallel robot part based on the dynamic model and two schemes of intelligent control for a hydraulically driven parallel mechanism based on the dynamic model: (1) a fuzzy-PID self-tuning controller composed of the conventional PID control and with fuzzy logic, and (2) adaptive neuro-fuzzy inference system-PID (ANFIS-PID) self-tuning of the gains of the PID controller, which are implemented independently to control each hydraulic cylinder of the parallel mechanism based on rod length predictions. The serial component of the hybrid robot can be analyzed using the equilibrium of reaction forces at the universal joint connections of the hexa-element. To achieve precise positional control of the end effector for maximum precision machining, the hydraulic cylinder should be controlled to hold the hexa-element. Thirdly, a finite element approach of multibody systems using the Special Euclidean group SE(3) framework is presented for a parallel mechanism with flexible piston rods under the influence of machining forces. The flexibility of the bodies is described using the nonlinear interpolation method with an exponential map. The equations of motion take the form of a differential algebraic equation on a Lie group, which is solved using a Lie group time integration scheme. The method relies on the local description of motions, so that it provides a singularity-free formulation, and no parameterization of the nodal variables needs to be introduced. The flexible slider constraint is formulated using a Lie group and used for modeling a flexible rod sliding inside a cylinder. The dynamic model of the system of six closed loop mechanisms was assembled using Hamilton’s principle and the Lagrange multiplier method. A linearized hydraulic control system based on rod length predictions was implemented independently to control the hydraulic cylinders. Consequently, the results of the simulations demonstrating the behavior of the robot machine are presented for each case study. In conclusion, this thesis studies the dynamic analysis of a special hybrid (serialparallel) robot for the above-mentioned special task involving the ITER and investigates different control algorithms that can significantly improve machining performance. These analyses and results provide valuable insight into the design and control of the parallel robot with flexible rods.