Defining of the material models for stainless steels to be used in FE modeling

The aim of this work is to study the results of tensile tests for austenitic stainless steel type 304 and make accurate FE-models according to the results of the tests. Tensile tests were made at Central Research Institute of Structural Material, Prometey at Saint Petersburg and Mariyenburg in Russia. The test specimens for the tensile tests were produced at Lappeenranta University of Technology in a Laboratory of Steel Structures. In total 4 different tests were made, two with base material specimens and two with transverse butt weld specimens. Each kind of a specimen was tested at room temperature and at low temperature. By comparing the results of room and low temperature tests of similar test specimen we get to study the results of work hardening that affect the austenitic steels at below room temperature. The produced specimens are to be modeled accurately and then imported for nonlinear FEM- analyzing. Using the data gained from the tensile tests the aim is to get the models work like the specimens did during the tests. By using the analyzed results of the FE-models the aim is to calculate and get the stress-strain curves that correspond to the results acquired from the tensile tests.

Simulation and material calibration of ultra high strength steel (UHSS) S960 welded joint under static tensile test utilizing finite element method (FEM)

The aim of this work was to calibrate the material properties including strength and strain values for different material zones of ultra-high strength steel (UHSS) welded joints under monotonic static loading. The UHSS is heat sensitive and softens by heat due to welding, the affected zone is heat affected zone (HAZ). In this regard, cylindrical specimens were cut out from welded joints of Strenx® 960 MC and Strenx® Tube 960 MH, were examined by tensile test. The hardness values of specimens’ cross section were measured. Using correlations between hardness and strength, initial material properties were obtained. The same size specimen with different zones of material same as real specimen were created and defined in finite element method (FEM) software with commercial brand Abaqus 6.14-1. The loading and boundary conditions were defined considering tensile test values. Using initial material properties made of hardness-strength correlations (true stress-strain values) as Abaqus main input, FEM is utilized to simulate the tensile test process. By comparing FEM Abaqus results with measured results of tensile test, initial material properties will be revised and reused as software input to be fully calibrated in such a way that FEM results and tensile test results deviate minimum. Two type of different S960 were used including 960 MC plates, and structural hollow section 960 MH X-joint. The joint is welded by BöhlerTM X96 filler material. In welded joints, typically the following zones appear: Weld (WEL), Heat affected zone (HAZ) coarse grained (HCG) and fine grained (HFG), annealed zone, and base material (BaM). Results showed that: The HAZ zone is softened due to heat input while welding. For all the specimens, the softened zone’s strength is decreased and makes it a weakest zone where fracture happens while loading. Stress concentration of a notched specimen can represent the properties of notched zone. The load-displacement diagram from FEM modeling matches with the experiments by the calibrated material properties by compromising two correlations of hardness and strength.

Sihtirummun väsymisominaisuuksien määrittäminen

Diplomityössä tutkittiin sihtirummun väsymisominaisuuksia. Sihtirumpu on laite, jota käytetään paperin valmistuksessa kuitumassojen käsittelyssä. Työn tavoitteena oli määrittää profiililankatyypin ja tukirenkaan erilaisten valmistustapojen vaikutus sihtirummun väsymiskestävyyteen. Lisäksi tutkittiin vauriomuotoa, jossa yksittäinen profiililanka irtoaa tukilangasta. Sihtirummun väsymisominaisuuksia määritettiin käyttämällä perinteisiä lujuusopin menetelmiä sekä FE-analyysiä ja väsytyskokeita. Teoreettisilla menetelmillä, jotka perustuivat loven vaikutuksen arviointiin, pyrittiin määrittämään perusaineen väsymislujuutta, ja väsytyskokeilla määritettiin sihtirummun hitsien väsymislujuuksia ja yksittäisen langan irtoamista. Sihtirummun hitsit olivat väsymislujuudeltaan huomattavasti perusainetta heikompia, eikä profiililankatyyppi vaikuttanut merkittävästi sihtirummun väsymiskestävyyteen. Hitsaamattoman tukirenkaan ja tukilangan liitoksen havaittiin nostavan sihtirummun väsymiskestävyyttä, mutta silloin ongelmana ovat tukirenkaan ja tukilangan väliin pääsevät kuidut. Yksittäisen profiililangan irtoamisen ei pitäisi rajoittaa sihtirummun väsymiskestävyyttä.

Constant and variable amplitude fatigue strength of high strength steel welds treated with ultrasonic impact treatment

Hitsattujen rakenteiden väsymiskestävyyttä pystytään parantamaan jälkikäsittelymenetelmillä, joistayksi, ultraäänikäsittely muokkaa hitsin geometriaa ja aiheuttaa puristusjäännösjännitystilan. Tässä tutkimuksessa verrataan kokeellisesti kuormaa kantamattoman hitsatun ja ui -käsitellyn rivan väsymislujuutta toisiinsa. Tutkimusohjelmaan kuuluu kahta teräslajia ja sekä vakio - että vaihtuva - amplitudista kuormitusta. Ultraäänikäsittelyllä saavutetaan väsymiskestoiän parantuminen vakio - ja vaihtuva - amplitudisella kuormituksella. Perusaineen lujuudella ei ole merkittää vaikutusta väsymislujuuteen kun liitos on hitsatussa tilassa. Tällöin väsymiskestävyyden määrää hitsin rajaviivan jännityskeskittymä. Ultraäänikäsitellyn hitsatunliitoksen väsymiskestävyys on suurempi korkeamman lujuuden omaavilla teräksillä. Tästä syystä korkealujuuksisten terästen käyttö ultraäänikäsiteltynä väsyttävästi kuormitetuissa kevytrakenteissa on perusteltua.

Alumiinirakenteiden kulumiskestävyyden parantaminen laserpintakäsittelyillä

Alumiini on pienen ominaispainonsa, hyvän korroosiokestävyytensä ja muotoiltavuutensa ansiosta runsaasti käytetty materiaali niin koneenosissa, kuin monissa muissakin rakenteissa. Alumiinin pehmeys ja huono kulumiskestävyys ovat rajoittaneet sen käyttöä. Alumiinin kovuuden ja kulumiskestävyyden parantaminen laajentaisi sen käyttömahdollisuuksia. Laserpintakäsittelymenetelmien käyttö on potentiaalinen, mutta vielä vähän tutkittu keino alumiinin kulumiskestävyyden parantamiseksi. Diplomityön teoriaosassa käsitellään materiaalin eri kulumismekanismeja, kohdemateriaali alumiinin ominaisuuksia ja tarkastellaan keinoja parantaa kulumiskestävyyttä sekä perinteisillä tekniikoilla että erityisesti lasertekniikoiden avulla. Diplomityön kokeellisessa osassa tehtiin laserpintakäsittelykokeita Nd:YAG-laserilla tavoitteena kovuuden ja kulumiskestävyyden parantaminen. Parhaat tulokset saavutettiin laserpinnanseostustekniikalla nikkelipohjaisella Inconel 625-seosaineella. Diplomityössä tehdyissä kokeissa saavutettiin yli 10-kertainen alumiinin pinnankovuus verrattuna käsittelemättömään perusaineeseen. Abrasiivinen kulumiskestävyys parantui parhaimmillaan yli kolminkertaiseksi verrattuna käsittelemättömään alumiiniin ja anodisoituihin vertailukappaleisiin. Tutkimuksessa määriteltiin myös parametrialue kokeissa käytetyille perus- ja lisäaineelle. Diplomityössä tehdyt kokeet toimivat hyvänä pohjana jatkokokeille.

Kulutus- korroosionkestävien materiaalien laserpinnoitus

Diplomityössä tutkitaan kulutus- ja korrosionkestävien materiaalien laserpinnoitusta. Laserpinnoituksessa sulatetaan uutta materiaalia työkappaleen pintaan lasersäteen avulla. Tarkoituksena on yleensä parantaa pinnan korroosion, kulumisen tai pintapaineen kestävyyttä. Laserpinnoitukseen liittyy useita etuja verrattuna konventionaalisiin päällehitsausprosesseihin. Työssä tutkittavat pinnoitemateriaalit ovat kobolttipohjaiset Stellite 1 ja Stellite 6, työkaluteräkset WR 4 ja WR 6 sekä metallimatriisikomposiitti Anval50/50+30 % Cr3C2. Pinnoitettavat perusaineet ovat hiiliteräs Fe 52, ruostumaton teräs AISI 316 ja valurauta GRP 500. Työn tavoitteena on löytää kunkin pinnoite/perusaine-yhdistelmän pinnoitusparametrit. Pinnoituskokeissa käytettiin LTKK:n 6 kW:n CO2-laseria. Pinnoitetuille koekappeleille tehtiin kovuusmittaukset ja kulutuskokeet. Pinnoitteiden mikrorakenteet analysoitiin ja sekoittumisasteet laskettiin. Virheitä tutkittiin silmämääräisesti sekä radiografisella kuvauksella. Optimiparametreja pinnoitemateriaaleille ei löydetty. Pinnoitteiden sekoittumisasteet muodostuivat suuriksi liiallisen lasertehon ja/tai huonon lisäaineen kohdistuksen vuoksi. Suuri sekoittuminen alensi pinnoitteiden kovuutta ja kulumiskestävyyttä. Pinnoitusparametreja arvioidaan koetulosten perusteella ja niille annetaan korjausehdotuksia. Lopuksi esitetään suosituksia tutkimusprojektin jatkotoimille.

The effects of some variables on CO2 laser-MAG hybrid welding

The CO2-laser-MAG hybrid welding process has been shown to be a productive choice for the welding industry, being used in e.g. the shipbuilding, pipe and beam manufacturing, and automotive industries. It provides an opportunity to increase the productivity of welding of joints containing air gaps compared with autogenous laser beam welding, with associated reductions in distortion and marked increases in welding speeds and penetration in comparison with both arc and autogenous laser welding. The literature study indicated that the phenomena of laser hybrid welding are mostly being studied using bead-on-plate welding or zero air gap configurations. This study shows it very clearly that the CO2 laser-MAG hybrid welding process is completely different, when there is a groove with an air gap. As in case of industrial use it is excepted that welding is performed for non-zero grooves, this study is of great importance for industrial applications. The results of this study indicate that by using a 6 kW CO2 laser-MAG hybrid welding process, the welding speed may also be increased if an air gap is present in the joint. Experimental trials indicated that the welding speed may be increased by 30-82% when compared with bead-on-plate welding, or welding of a joint with no air gap i.e. a joint prepared as optimum for autogenous laser welding. This study demonstrates very clearly, that the separation of the different processes, as well as the relative configurations of the processes (arc leading or trailing) affect welding performance significantly. These matters influence the droplet size and therefore the metal transfer mode, which in turn determined the resulting weld quality and the ability to bridge air gaps. Welding in bead-onplate mode, or of an I butt joint containing no air gap joint is facilitated by using a leading torch. This is due to the preheating effect of the arc, which increases the absorptivity of the work piece to the laser beam, enabling greater penetration and the use of higher welding speeds. With an air gap present, air gap bridging is more effectively achieved by using a trailing torch because of the lower arc power needed, the wider arc, and the movement of droplets predominantly towards the joint edges. The experiments showed, that the mode of metal transfer has a marked effect on gap bridgeability. Transfer of a single droplet per arc pulse may not be desirable if an air gap is present, because most of the droplets are directed towards the middle of the joint where no base material is present. In such cases, undercut is observed. Pulsed globular and rotational metal transfer modes enable molten metal to also be transferred to the joint edges, and are therefore superior metal transfer modes when bridging air gaps. It was also found very obvious, that process separation is an important factor in gap bridgeability. If process separation is too large, the resulting weld often exhibits sagging, or no weld may be formed at all as a result of the reduced interaction between the component processes. In contrast, if the processes are too close to one another, the processing region contains excess molten metal that may create difficulties for the keyhole to remain open. When the distance is optimised - i.e. a separation of 0-4 mm in this study, depending on the welding speed and beam-arc configuration - the processes act together, creating beneficial synergistic effects. The optimum process separation when using a trailing torch was found to be shorter (0-2 mm) than when a leading torch is used (2-4 mm); a result of the facilitation of weld pool motion when the latter configuration is adopted. This study demonstrates, that the MAG process used has a strong effect on the CO2-laser-MAG hybrid welding process. The laser beam welding component is relatively stable and easy to manage, with only two principal processing parameters (power and welding speed) needing to be adjusted. In contrast, the MAG process has a large number of processing parameters to optimise, all of which play an important role in the interaction between the laser beam and the arc. The parameters used for traditional MAG welding are often not optimal in achieving the most appropriate mode of metal transfer, and weld quality in laser hybrid welding, and must be optimised if the full range of benefits provided by hybrid welding are to be realised.

A Practical Micro Mechanical Model Based Local Approach Methodology for the Analysis of Ductile Fracture of Welded T-Joints

This thesis concentrates on developing a practical local approach methodology based on micro mechanical models for the analysis of ductile fracture of welded joints. Two major problems involved in the local approach, namely the dilational constitutive relation reflecting the softening behaviour of material, and the failure criterion associated with the constitutive equation, have been studied in detail. Firstly, considerable efforts were made on the numerical integration and computer implementation for the non trivial dilational Gurson Tvergaard model. Considering the weaknesses of the widely used Euler forward integration algorithms, a family of generalized mid point algorithms is proposed for the Gurson Tvergaard model. Correspondingly, based on the decomposition of stresses into hydrostatic and deviatoric parts, an explicit seven parameter expression for the consistent tangent moduli of the algorithms is presented. This explicit formula avoids any matrix inversion during numerical iteration and thus greatly facilitates the computer implementation of the algorithms and increase the efficiency of the code. The accuracy of the proposed algorithms and other conventional algorithms has been assessed in a systematic manner in order to highlight the best algorithm for this study. The accurate and efficient performance of present finite element implementation of the proposed algorithms has been demonstrated by various numerical examples. It has been found that the true mid point algorithm (a = 0.5) is the most accurate one when the deviatoric strain increment is radial to the yield surface and it is very important to use the consistent tangent moduli in the Newton iteration procedure. Secondly, an assessment of the consistency of current local failure criteria for ductile fracture, the critical void growth criterion, the constant critical void volume fraction criterion and Thomason's plastic limit load failure criterion, has been made. Significant differences in the predictions of ductility by the three criteria were found. By assuming the void grows spherically and using the void volume fraction from the Gurson Tvergaard model to calculate the current void matrix geometry, Thomason's failure criterion has been modified and a new failure criterion for the Gurson Tvergaard model is presented. Comparison with Koplik and Needleman's finite element results shows that the new failure criterion is fairly accurate indeed. A novel feature of the new failure criterion is that a mechanism for void coalescence is incorporated into the constitutive model. Hence the material failure is a natural result of the development of macroscopic plastic flow and the microscopic internal necking mechanism. By the new failure criterion, the critical void volume fraction is not a material constant and the initial void volume fraction and/or void nucleation parameters essentially control the material failure. This feature is very desirable and makes the numerical calibration of void nucleation parameters(s) possible and physically sound. Thirdly, a local approach methodology based on the above two major contributions has been built up in ABAQUS via the user material subroutine UMAT and applied to welded T joints. By using the void nucleation parameters calibrated from simple smooth and notched specimens, it was found that the fracture behaviour of the welded T joints can be well predicted using present methodology. This application has shown how the damage parameters of both base material and heat affected zone (HAZ) material can be obtained in a step by step manner and how useful and capable the local approach methodology is in the analysis of fracture behaviour and crack development as well as structural integrity assessment of practical problems where non homogeneous materials are involved. Finally, a procedure for the possible engineering application of the present methodology is suggested and discussed.

Suurlujuusterästen hitsausliitoksen HAZ -vyöhykkeen murtumissitkeys

Suurlujuusterästen käyttö erityisesti auto-, kuljetusväline- ja nostovälineteollisuudessa on lisääntynyt jo pidemmän aikaa. Teräsvalmistajat kehittävätkin jatkuvasti lujempia ja paremmin hitsattavia teräslaatuja markkinoille. Lujempia teräksiä käyttämällä on mahdollista saavuttaa materiaali- ja painosäästöä, jolla on suora vaikutus hyötykuorman lisääntymiseen, polttoainetalouteen, suoritusarvoihin ja jopa valmistuskustannuksiin. Tässä diplomityössä tutkittiin kahdeksan eri suurlujuusteräksen ja kolmen kulutusteräksen HAZ-alueen murtumissitkeyttä kolmella eri lämmöntuonnilla tehdyllä hitsauksella. Suurlu-juusterästen myötölujuustaso vaihteli 650 MPa:n ja 700 MPa:n välillä, ja kulutusteräksillä vastaavasti 800 MPa:n ja 1000 MPa:n välillä. Murtumissitkeyskokeet tehtiin standardoidun CTOD-testausmenetelmän mukaisesti -40 °C lämpötilassa. Kokeissa käytettiin 10 mm x 5 mm SE(B)-kolmipistetaivutussauvoja. Koetuloksia voidaan käyttää apuna arvioitaessa eri teräslaatujen hitsauksellista sopivuutta erityisesti väsyttävän kuormituksen alaiseen rakenteeseen. Kokeiden tuloksena saatiin jokaiselle materiaalille neljä CTOD-arvoa. Kolmella eri lämmöntuonnilla tehtyjen koesauvojen lisäksi mitattiin ilman hitsausta olevista koesauvoista perusaineen murtumissitkeys. Yhteensä CTOD-koe tehtiin 44 koesauvalle ja lisäksi muutamalle harjoitussauvalle. Testattavien kappaleiden suuren määrän takia kokeet voitiin tehdä jokaiselle materiaali- lämmöntuonti- yhdistelmälle ainoastaan yhteen kertaan.

Suurlujuusterästen suuren lujuuden ja pienen murtovenymän tuomat erityispiirteet teräsrakenteen suunnittelijalle

Suurlujuusteräskonstruktioiden suunnittelu eroaa perinteisten rakenneterästen vastaavasta lukuisten lisähuomiota vaativien ilmiöiden ja seikkojen osalta, jotka kytkeytyvät toisiinsa rakenteen valmistettavuuden ja toiminnallisuuden kautta. Lujuuden sallima vapaampi suunnittelu esimerkiksi ohuempine materiaalivahvuuksineen ja näennäisesti vapaampine elementtigeometrioineen kumuloituu suurlujuusteräsmateriaalin kautta vaativampana työstettävyytenä. Tämä heijastuu suunnittelijalle materiaalin pienen murtovenymän ja käytettävissä olevat laitteistoresurssien kautta. Suurlujuusterästen muovaaminen vaatii perinteisiin rakenneteräksiin nähden suurempaa voimankäyttöä, mutta pieni murtovenymä rajoittaa saavutettavissa olevia muotoja. Materiaalivahvuuksien muuttuessa vaatii hitsausliitosten suunnittelu esimerkiksi railomuotojen uudelleensuunnittelua, sekä lämmöntuonnin aiheuttamien muutosten tarkempaa huomioimista. Näiden yhteensovittaminen ohjaa suunnittelijan poikkeuksetta hakemaan ratkaisuja erilaisista hitsausaineista ja -prosesseista. Suuren lujuuden ja pienen murtovenymän suurlujuusteräselementtien mekaanisten ominaisuuksien ja erilaisen elementtigeometrian yhdistelmänä kumuloituva rakennetekninen käyttäytyminen eroaa selvästi perinteisistä teräslaaduista. Yksittäisten elementtien suhteen korostuvat esimerkiksi stabiliteettiomiinaisuudet, sekä kokonaisten rakenteiden suhteen liitosratkaisujen vaikutus koko konstruktion toimintaan. Onnistuneella suurlujuusteräsuunnittelulla saavutettuja etuja ovat käyttökohteesta riippuen esimerkiksi kymmenien prosenttien massa- ja kustannussäästöjen kautta kumuloituvat konstruktion toiminnalliset edut. Suuren lujuuden terästen materiaaliteknisten erityispiirteiden suhteen ei kuitenkaan ole tarjolla perinteisiä rakenneteräksiä vastaavaa määrää yhteisesti sovittuja standardoituja suunnitteluohjeita. Tämän johdosta korostuu suunnittelijan kyky hahmottaa teräsmateriaalin lujuusluokan taakse piiloutuvat ilmiöt, sekä materiaalitekniset erityispiirteet ja niiden kytkeytyminen toisiinsa valmistettavuuden ja toiminnallisuuden kautta.

Advanced orbital pipe welding

Since the introduction of automatic orbital welding in pipeline application in 1961, significant improvements have been obtained in orbital pipe welding systems. Requirement of more productive welding systems for pipeline application forces manufacturers to innovate new advanced systems and welding processes for orbital welding method. Various methods have been used to make welding process adaptive, such as visual sensing, passive visual sensing, real-time intelligent control, scan welding technique, multi laser vision sensor, thermal scanning, adaptive image processing, neural network model, machine vision, and optical sensing. Numerous studies are reviewed and discussed in this Master’s thesis and based on a wide range of experiments which already have been accomplished by different researches the vision sensor are reported to be the best choice for adaptive orbital pipe welding system. Also, in this study the most welding processes as well as the most pipe variations welded by orbital welding systems mainly for oil and gas pipeline applications are explained. The welding results show that Gas Metal Arc Welding (GMAW) and its variants like Surface Tension Transfer (STT) and modified short circuit are the most preferred processes in the welding of root pass and can be replaced to the Gas Tungsten Arc Welding (GTAW) in many applications. Furthermore, dual-tandem gas metal arc welding technique is currently considered the most efficient method in the welding of fill pass. Orbital GTAW process mostly is applied for applications ranging from single run welding of thin walled stainless tubes to multi run welding of thick walled pipes. Flux cored arc welding process is faster process with higher deposition rate and recently this process is getting more popular in pipe welding applications. Also, combination of gas metal arc welding and Nd:YAG laser has shown acceptable results in girth welding of land pipelines for oil and gas industry. This Master’s thesis can be implemented as a guideline in welding of pipes and tubes to achieve higher quality and efficiency. Also, this research can be used as a base material for future investigations to supplement present finding.

Testate amoebae (thecamoebians) as indicators of aquatic mine impact

The environmental impacts of a single mine often remain local, but acidic and metal-rich acid mine drainage (AMD) from the waste materials may pose a serious threat to adjacent surface waters and their ecosystems. Testate amoebae (thecamoebian) analysis was used together with lake sediment geochemistry to study and evaluate the ecological effects of sulphidic metal mines on aquatic environments. Three different mines were included in the study: Luikonlahti Cu-mine in Kaavi, eastern Finland, Haveri Cu-Au mine in Ylöjärvi, southern Finland and Pyhäsalmi Zn-Cu-S mine in Pyhäjärvi, central Finland. Luikonlahti and Haveri are closed mines, but Pyhäsalmi is still operating. The sampling strategy was case specific, and planned to provide a representative sediment sample series to define natural background conditions, to detect spatial and temporal variations in mine impacts, to evaluate the possible recovery after the peak contamination, and to distinguish the effects of other environmental factors from the mining impacts. In the Haveri case, diatom analyses were performed alongside thecamoebian analysis to evaluate the similarities and differences between the two proxies. The results of the analyses were investigated with multivariate methods (direct and indirect ordinations, diversity and distance measure indices). Finally, the results of each case study were harmonized, pooled, and jointly analyzed to summarize the results for this dissertation. Geochemical results showed broadly similar temporal patterns in each case. Concentrations of ions in the pre-disturbance samples defined the natural baseline against which other results were compared. The beginning of the mining activities had only minor impacts on sediment geochemistry, mainly appearing as an increased clastic input into the lakes at Haveri and Pyhäsalmi. The active mining phase was followed by the metallic contamination and, subsequently, by the most recent change towards decreased but still elevated metal concentrations in the sediments. Because of the delay in the oxidation of waste material and formation of AMD, the most intense, but transient metal contamination phase occurred in the post-mining period at Luikonlahti and Haveri. At Pyhäsalmi, the highest metal contamination preceded effluent mitigation actions. Spatial gradients were observed besides the temporal evolution in both the pre-disturbance and mine-impacted samples from Luikonlahti and Pyhäsalmi. The geochemical gradients varied with distance from the main source of contaminants (dispersion and dilution) and with water depth (redox and pH). The spatial extent of the highest metal contamination associated with these mines remained rather limited. At Haveri, the metallic impact was widespread, with the upstream site in another lake basin found to be contaminated. Changes in thecamoebian assemblages corresponded well with the geochemical results. Despite some differences, the general features and ecological responses of the faunal assemblages were rather similar in each lake. Constantly abundant strains of Difflugia oblonga, Difflugia protaeiformis and centropyxids formed the core of these assemblages. Increasing proportions of Cucurbitella tricuspis towards the surface samples were found in all of the cases. The results affirmed the indicator value of some already known indicator forms, but such as C. tricuspis and higher nutrient levels, but also elicited possible new ones such as D. oblonga ‘spinosa’ and clayey substrate, high conductivity and/or alkalinity, D. protaeiformis ‘multicornis’ and pH, water hardness and the amount of clastic material and Centropyxis constricta ‘aerophila’ and high metal and S concentrations. In each case, eutrophication appeared to be the most important environmental factor, masking the effects of other variables. Faunal responses to high metal inputs in sediments remained minor, but were nevertheless detectable. Besides the trophic state of the lake, numerical methods suggested overall geochemical conditions (pH, redox) to be the most important factor at Luikonlahti, whereas the Haveri results showed the clearest connection between metals and amoebae. At Pyhäsalmi, the strongest relationships were found between Ca- and S-rich present loading, redox conditions and substrate composition. Sediment geochemistry and testate amoeba analysis proved to be a suitable combination of methods to detect and describe the aquatic mine impacts in each specific case, to evaluate recovery and to differentiate between the effects of different anthropogenic and natural environmental factors. It was also suggested that aquatic mine impacts can be significantly mitigated by careful design and after-care of the waste facilities, especially by reducing and preventing AMD. The case-specific approach is nevertheless necessary because of the unique characteristics of each mine and variations in the environmental background conditions.

Surface transformation hardening of carbon steel with high power fiber laser

This study investigated the surface hardening of steels via experimental tests using a multi-kilowatt fiber laser as the laser source. The influence of laser power and laser power density on the hardening effect was investigated. The microhardness analysis of various laser hardened steels was done. A thermodynamic model was developed to evaluate the thermal process of the surface treatment of a wide thin steel plate with a Gaussian laser beam. The effect of laser linear oscillation hardening (LLOS) of steel was examined. An as-rolled ferritic-pearlitic steel and a tempered martensitic steel with 0.37 wt% C content were hardened under various laser power levels and laser power densities. The optimum power density that produced the maximum hardness was found to be dependent on the laser power. The effect of laser power density on the produced hardness was revealed. The surface hardness, hardened depth and required laser power density were compared between the samples. Fiber laser was briefly compared with high power diode laser in hardening medium-carbon steel. Microhardness (HV0.01) test was done on seven different laser hardened steels, including rolled steel, quenched and tempered steel, soft annealed alloyed steel and conventionally through-hardened steel consisting of different carbon and alloy contents. The surface hardness and hardened depth were compared among the samples. The effect of grain size on surface hardness of ferritic-pearlitic steel and pearlitic-cementite steel was evaluated. In-grain indentation was done to measure the hardness of pearlitic and cementite structures. The macrohardness of the base material was found to be related to the microhardness of the softer phase structure. The measured microhardness values were compared with the conventional macrohardness (HV5) results. A thermodynamic model was developed to calculate the temperature cycle, Ac1 and Ac3 boundaries, homogenization time and cooling rate. The equations were numerically solved with an error of less than 10-8. The temperature distributions for various thicknesses were compared under different laser traverse speed. The lag of the was verified by experiments done on six different steels. The calculated thermal cycle and hardened depth were compared with measured data. Correction coefficients were applied to the model for AISI 4340 steel. AISI 4340 steel was hardened by laser linear oscillation hardening (LLOS). Equations were derived to calculate the overlapped width of adjacent tracks and the number of overlapped scans in the center of the scanned track. The effect of oscillation frequency on the hardened depth was investigated by microscopic evaluation and hardness measurement. The homogeneity of hardness and hardened depth with different processing parameters were investigated. The hardness profiles were compared with the results obtained with conventional single-track hardening. LLOS was proved to be well suitable for surface hardening in a relatively large rectangular area with considerable depth of hardening. Compared with conventional single-track scanning, LLOS produced notably smaller hardened depths while at 40 and 100 Hz LLOS resulted in higher hardness within a depth of about 0.6 mm.

Eri MAG-hitsausprosessien ja -parametrien vaikutus suurlujuusteräksestä valmistetun otsapienahitsin äärikestävyyteen, muodonmuutoskykyyn ja vauriomuotoon

Työssä tutkittiin Ruukki Oyj:n suorasammutetusta S960QC-teräksestä valmistetun kuormaakantavan levyjen ristiliitoksen pienahitsien lujuutta, muodonmuutoskykyä ja vaurioitumismekanismia laajaan kokeelliseen aineistoon perustuen. Tärkeimpänä muuttujana koematriisissa olivat eri MAG-hitsausprosessit. Perinteisen kuumakaarihitsauksen vertailukohteena oli Kemppi Oy:n uusi adaptiivinen valokaaren pituutta säätävä WiseFusion-hitsaustoiminto kuuma- ja pulssikaarihitsauksessa. Näiden kolmen hitsausprosessin rinnalla varioitiin erisuuruisia a-mittoja, eri hitsauslisäaineita ja hitsin erikylkisyyttä. Lisäksi juuritunkeuman estämisen vaikutusta hitsien käyttäytymiseen tutkittiin täydentävällä koesarjalla, jossa tunkeuman muodostuminen estettiin levyjen väliin asetetulla volframilevyllä. Työn perimmäisenä tavoitteena oli selvittää syy aiemmassa tutkimuksessa havaitulle pienahitsien vaurioitumiselle leikkautumalla sularajaa pitkin. Sularajan suhteellista pituutta saadaan kasvatettua estämällä hitsin juuritunkeuma ja absoluuttista pituutta saadaan lisää kateettipoikkeaman avulla. Lisäksi tutkimuksessa oli tarkoitus tuoda esille suurlujuusteräksisen liitoksen eri mitoituslähtökohdat (mm. lämmöntuonnin kontrollointi). Tämän vuoksi hitsausparametrit mitattiin jännitteen ja virran hetkellisiin arvoihin perustuen, jolloin kuuma- ja pulssikaarihitsauksen laskennalliset hitsaustehot ovat vertailukelpoisia. Koehitseistä valmistettiin hieet hitsien tarkan geometrian määrittämiseksi ja liitoksen mekaaniset ominaisuudet tutkittiin vetokokeella. Tulosten perusteella sularajavaurio aktivoituu pulssikaarella hitsatuissa koekappaleissa. Tämä aiheutunee pulssi- ja kuumakaarihitsauksen sularajan mikrorakenteiden eroavaisuudesta. Sularajavaurio näyttää huonontavan hitsien muodonmuutoskykyä, mutta jatkokokeita tuloksen verifioimiseksi on tehtävä. S960QC-teräkselle ominaisen pehmenneen vyöhykkeen vaurio ei aktivoitunut, vaikka Ruukin antamat jäähtymisaikasuositukset ylitettiin reilusti.

Use of fiber-reinforced composite framework and thermochromic pigment in maxillofacial prostheses

The purpose of this investigation was to evaluate the possibility to enhance certain qualities of facial prostheses. Polymethyl methacrylate is still being used as base mate¬rial or clip carrier material, but it is hard and heavy, and debonding of the silicone from the acrylic base material is a frequent problem. This thesis aims to evaluate the use of fiber-reinforced composite (FRC) as framework material for maxillofacial silicone prostheses. FRC has been used as reinforcement in removable and fixed partial dentures since the 1990s. This material is lightweight and can be fabricated to compress the margins of the prosthesis slightly, to keep it tightly against the skin during jaw movements and facial expressions. Additionally, the use of a thermochromic pigment, colorless in room temperature and red in a cold environment, was studied in order to evaluate the possibility of using this color changing pigment in facial prostheses to mimic the color change of facial skin in cold weather. The tensile bond strength between pre-impregnated, unidirectional FRC and maxillofacial silicone elastomer was studied. Three different bonding agents or primers were compared. Bond strength was improved by one of the primers and by roughening the surface. The effect of a skin compressing glass fiber-reinforced composite framework on facial skin blood flow was studied by using a face mask, constructed with a compression pad corresponding to the outer margin of a glass fiber-reinforced framework beam of a facial prosthesis. The skin blood flow of ten healthy volunteers, aged 23-25 years, was measured during touch, light, and moderate compression of the skin, by using laser Doppler imaging technique. None of the compressions showed any marked effects on local skin blood flow. There were no significant differences between blood flow during compression and at baseline. Maxillofacial silicone elastomer was colored intrinsically with conventional color pigments: a control group containing only conventional pigments was compared to two test groups with 0.2 wt% and 0.6 wt% thermochromic pigment added. The color of the material was measured with a spectrophotometer in room temperature and after storage in a freezer. The color stability of the maxillofacial silicone elastomer colored with thermo¬chromic pigment was evaluated by artificial aging. The color dif¬ference of the L* (lightness) and a* values (redness), comparing color after the samples were stored at room temperature and in a freezer (-19°C), was statistically significant for both 0.2 wt% and 0.6 wt% thermo¬chromic pigment groups. The differences in the b* values (yellowness) were statistically significant for the 0.6 wt% group. Exposure to ultraviolet (UV) radiation led to visually noticeable and statistically signifi¬cant color changes (ΔE) in all color values in both test groups. The specimens containing thermochromic pigment were very sensitive to UV radiation. In conclusion, a framework of fiber-reinforced composite can successfully be bonded to maxillofacial silicone elastomer, and a framework beam, compressing the facial skin, did not remarkably alter the skin blood flow on healthy, young adults. The thermochromic pigment showed color change in maxillofacial silicone elastomer. However, artificial aging showed that it was too sensitive to UV radiation to be used, as such, in maxillofacial prostheses.