Choice of Optimal MembraneProcesses for Economical Treatment of Paper Machine Clear Filtrate

In this thesis membrane filtration of paper machnie clear filtrate was studied. The aim of the study was to find membrane processes which are able to produce economically water of sufficient purity from paper machine white water or its saveall clarified fractions for reuse in the paper machnie short circulation. Factors affecting membrane fouling in this application were also studied. The thesis gives an overview af experiments done on a laboratory and a pilot scale with several different membranes and membrane modules. The results were judged by the obtained flux, the fouling tendency and the permeate quality assessed with various chemical analyses. It was shown that membrane modules which used a turbulence promotor of some kind gave the highest fluexes. However, the results showed that the greater the reduction in the concentration polarisation layer caused by increased turbulence in the module, the smaller the reductions in measured substances. Out of the micro-, ultra- and nanofiltration membranes tested, only nanofiltration memebranes produced permeate whose quality was very close to that of the chemically treated raw water used as fresh water in most paper mills today and which should thus be well suited for reuse as shower water both in the wire and press section. It was also shown that a one stage nanofiltration process was more effective than processes in which micro- or ultrafiltration was used as pretreatment for nanofiltration. It was generally observed that acidic pH, high organic matter content, the presence of multivalent ions, hydrophobic membrane material and high membrane cutoff increased the fouling tendency of the membranes.

Numerical and ExperimentalModelling of Gas Flow and Heat Transfer in the Air Gap of An Electric Machine

This work deals with the cooling of high-speed electric machines, such as motors and generators, through an air gap. It consists of numerical and experimental modelling of gas flow and heat transfer in an annular channel. Velocity and temperature profiles are modelled in the air gap of a high-speed testmachine. Local and mean heat transfer coefficients and total friction coefficients are attained for a smooth rotor-stator combination at a large velocity range. The aim is to solve the heat transfer numerically and experimentally. The FINFLO software, developed at Helsinki University of Technology, has been used in the flow solution, and the commercial IGG and Field view programs for the grid generation and post processing. The annular channel is discretized as a sector mesh. Calculation is performed with constant mass flow rate on six rotational speeds. The effect of turbulence is calculated using three turbulence models. The friction coefficient and velocity factor are attained via total friction power. The first part of experimental section consists of finding the proper sensors and calibrating them in a straight pipe. After preliminary tests, a RdF-sensor is glued on the walls of stator and rotor surfaces. Telemetry is needed to be able to measure the heat transfer coefficients at the rotor. The mean heat transfer coefficients are measured in a test machine on four cooling air mass flow rates at a wide Couette Reynolds number range. The calculated values concerning the friction and heat transfer coefficients are compared with measured and semi-empirical data. Heat is transferred from the hotter stator and rotor surfaces to the coolerair flow in the air gap, not from the rotor to the stator via the air gap, althought the stator temperature is lower than the rotor temperature. The calculatedfriction coefficients fits well with the semi-empirical equations and precedingmeasurements. On constant mass flow rate the rotor heat transfer coefficient attains a saturation point at a higher rotational speed, while the heat transfer coefficient of the stator grows uniformly. The magnitudes of the heat transfer coefficients are almost constant with different turbulence models. The calibrationof sensors in a straight pipe is only an advisory step in the selection process. Telemetry is tested in the pipe conditions and compared to the same measurements with a plain sensor. The magnitudes of the measured data and the data from the semi-empirical equation are higher for the heat transfer coefficients than thenumerical data considered on the velocity range. Friction and heat transfer coefficients are presented in a large velocity range in the report. The goals are reached acceptably using numerical and experimental research. The next challenge is to achieve results for grooved stator-rotor combinations. The work contains also results for an air gap with a grooved stator with 36 slots. The velocity field by the numerical method does not match in every respect the estimated flow mode. The absence of secondary Taylor vortices is evident when using time averagednumerical simulation.

Lämmönsiirron numeerinen laskenta profiloidulle kanavalle.

Työn tavoitteena oli tutkia aaltomaisen profiloinnin vaikutusta suorien jäähdytyskanavien lämmönsiirtoon ja painehäviöön. Erilaisia profiileja oli kymmenen kappaletta ja ne olivat 5mm leveitä ja 30cm pitkiä kukin. Ne laskettiin kolmeulotteisina tapauksina FINFLO-virtausratkaisijalla kolmella eri Reynoldsin luvulla, jotka vastasivat laminaarista, osittain turbulenttista ja lähes kokonaan turbulenttista virtausta. Lämmönsiirtoaine oli kuiva +30°C ilma ja profiloinnin toteutustapa oli toisiaan sivuavat ympyräkaaret kolmella erilaisella säteen arvolla ja kolmella erilaisella aallonpituuden arvolla. Lisäksi laskettiin saman levyisen tasokanavan arvot jokaisella Reynoldsin luvulla kaksiulotteisina tapauksina. Näitä profiloimattomia kanavia pidettiin referenssitapauksina. Tuloksena havaittiin että profiloimalla saadaan yksiselitteisesti suurempi lämpöteho ulos samasta tilavuudesta. Lämmönsiirtokerroin kasvaa profiloinnin avulla parhaimmillaan n. 20% käytetystä turbulenssimallista tai lämmönsiirtokertoimen määritelmästä riippumatta. Painehäviö kasvaa myös aina, mutta kitkakerroin voi hieman pienentyä. Profiilin varsinaisena hyvyyskriteerinä pidettiin lämmönsiirtokertoimen ja kitkakertoimen suhdetta h/f. Se osoittautui riippuvaksi Reynoldsin luvusta ja turbulenssimallista; ASM ja Chien k-έ -mallit ennustavat transitioetäisyyden eri tavalla. Laminaarisilla virtauksilla h/f :n vaihtelu oli vähäistä; suhde vaihteli vain ±5% eri profiilien kesken. ASM-mallilla havaittiin sekundääripyörteilyä, ehkä siksi että se mallintaa anisotrooppisen turbulenssin. Chien k-έ malli ennusti suuremman ja aikaisemmin alkavan turbulenttisuuden kuin ASM. Lisäksi havaittiin mm. että tietyillä profiileilla muodostuu kanavan kapeimpaan kohtaan selvä virtausnopeuden paikallinen minimi seinämän läheisyyden takia.

Germinability of Norway spruce and scots pine pollen exposed to open air

Summary

Seedling establishment after prescribed burning of a Clear-Cut and Partially Cut mesic boreal forest in Southern Finland

Summary

Effect of soil wetness on air composition and nitrous oxide emission in a loam soil

Selostus: Maan märkyyden vaikutus ilman koostumukseen ja dityppioksidiemissioon hiuemaassa