GIS assessing traditional and modern agricultural land use/land cover change. A case study 1959-2005: Rekijoki, Somero, SW-Finland

Finland’s rural landscape has gone through remarkable changes from the 1950’s, due to agricultural developments. Changed farming practices have influenced especially traditional landscape management, and modifications in the arable land structure and grasslands transitions are notable. The review of the previous studies reveal the importance of the rural landscape composition and structure to species and landscape diversity, whereas including the relevance in presence of the open ditches, size of the field and meadow patches, topology of the natural and agricultural landscape. This land-change study includes applying remote sensed data from two time series and empirical geospatial analysis in Geographic Information Systems (GIS). The aims of this retrospective research is to detect agricultural landscape use and land cover change (LULCC) dynamics and discuss the consequences of agricultural intensification to landscape structure covering from the aspects of landscape ecology. Measurements of LULC are derived directly from pre-processed aerial images by a variety of analytical procedures, including statistical methods and image interpretation. The methodological challenges are confronted in the process of landscape classification and combining change detection approaches with landscape indices. Particular importance is paid on detecting agricultural landscape features at a small scale, demanding comprehensive understanding of such agroecosystems. Topological properties of the classified arable land and valley are determined in order to provide insight and emphasize the aspect the field edges in the agricultural landscape as important habitat. Change detection dynamics are presented with change matrix and additional calculations of gain, loss, swap, net change, change rate and tendencies are made. Transition’s possibility is computed following Markov’s probability model and presented with matrix, as well. Thesis’s spatial aspect is revealed with illustrative maps providing knowledge of location of the classified landscape categories and location of the dynamics of the changes occurred. It was assured that in Rekijoki valley’s landscape, remarkable changes in landscape has occurred. Landscape diversity has been strongly influenced by modern agricultural landscape change, as NP of open ditches has decreased and the MPS of the arable plot has decreased. Overall change in the diversity of the landscape is determined with the decrease of SHDI. Valley landscape considered as traditional land use area has experienced major transitional changes, as meadows class has lost almost one third of the area due to afforestation. Also, remarkable transitions have occurred from forest to meadow and arable land to built area. Boundaries measurement between modern and traditional landscape has indicated noticeable proportional increase in arable land-forest edge type and decrease in arable land-meadow edge type. Probability calculations predict higher future changes for traditional landscape, but also for arable land turning into built area.

Supplier Evaluation Using Analytical Hierarchy Process

The goal of the thesis is to make a supplier evaluation using analytical hierarchy process. Before the supplier evaluation is performed there will be introduced the principles of purchasing which gives a viewpoint to the supplier evaluation and management. The thesis will also give an overview on quality, performance and forecasts which are very important to the supplier evaluation and future improvements. The chapter which describes analytical hierarchy process will show the reader what exactly is analytical hierarchy process and how can it be utilized in supplier evaluation. In the later stages, thesis will provide information about the case company EADS Secure Networks Oy, the processes applied there towards purchasing and how the analytical hierarchy process is applied in practise. In the end of the thesis there will be an overview about each supplier’s strong and weak points as well as some comments and ideas about developing also EADS Secure Networks procedures to a direction which would benefit the whole customer–supplier–chain.

Pankkitoiminnan riskienhallinta ja riskienhallintaraportointi Puolassa

Tutkimuksessa tarkastellaan julkisesti noteerattujen pankkien riskienhallintaraportoinnin nykykäytäntöä Puolassa. Tutkimus jakaantuu kahteen osaan: Tutkimuksen ensimmäisessä osassa esitellään pankkitoimintaa, pankkitoiminnan riskejä ja riskienhallintaa. Pankkitoiminnan riskejä ovat luotto- ja markkinariskit, lisäksi puhutaan operatiivisista ja ympäristöriskeistä. Tutkimuksen toisessa osassa selvitetään ja kuvataan sitä, millaista on tutkimuksen kohdeyritysten riskienhallinta ja riskienhallintaraportointi, tutkimuksen tarkoituksena on myös verrata pankkien riskienhallintaraportointia keskenään. Tutkimuksen kohteena on 13 Varsovan pörssissä listattua pankkia. Tutkimusaineistona käytetään näiden pankkien vuoden 2005 vuosikertomuksia. Kysymyksessä on laadullinen tapaustutkimus, jolle on tyypillistä kuvaileva ja selittävä tutkimusote. Aineiston analyysimenetelmänä on käytetty pattern matchingiä, jonka avulla tutkitaan aineistosta löytyviä riskienhallintaraportoinnin osatekijöitä/indikaattoreita ja verrataan niitä oletettuihin malleihin. Tutkittujen riskienhallintaraporttien perusteella voidaan todeta, että pankkitoiminnan ydinriskeistä: luotto-, korko-, valuutta- ja likviditeettiriskeistä raportoidaan hyvin. Sen sijaan puutteita löytyy operatiivisten ja ympäristöriskien raportoinnista. Suurin osa pankeista raportoi operatiivisista riskeistä, mutta raportointi on pintapuolista ja analysointi puuttuu. Ympäristöriskeistä raportointi ei ole yleistä. Raportoinnin laajuus ja informatiivisuus vaihtelevat pankkien kesken: Suuret, kansainväliset pankkikonsernit raportoivat riskeistään laajasti ja informatiivisesti, kun taas pienemmillä, kansallisilla pankeilla raportointi jää usean pankin kohdalla suppeaksi. Syitä raportoinnin eroille on monia: Yksi syistä on IFRS-standardien vakiintumaton käyttö pienimmillä, kansallisilla pankeilla verrattuna kansainvälisiin pankkikonserneihin. Kansainvälisillä pankkikonserneilla on paremmat valmiudet raportoida riskienhallinnastaan verrattuna pienimpiin pankkeihin, jotka julkaisivat tilinpäätöksensä ensimmäistä kertaa IFRS-standardien mukaisesti vuonna 2005. Yhtenä selittävänä tekijänäraportoinnin eroille voidaan myös mainita omistuspohja: sijoittajainformaation merkitys on korostunut erityisesti organisaatioissa, joissa on laaja, kansainvälinen omistuspohja. Sen sijaan valtio-omisteisessa yrityksessä sijoittajainformaation merkitys on vähäisempi. Myös yrityskulttuuri vaikuttaa siihen, missä laajuudessa, ja mitä tietoa yritys antaa julkisuuteen. Pankit ovat myös tarkkoja maineestaan, mitä tietoa voidaan julkaista ja mitä vaikutuksia tiedon julkaisemisellaon yrityskuvaan. Sen sijaan pankin koolla ei välttämättä ole vaikutusta riskienhallintaraportoinnin laajuuteen ja informatiivisuuteen.

Effect of Noncondensable Gases on Circulation of Primary Coolant in Nuclear Power Plants in Abnormal Situations

The present study focuses on two effects of the presence of a noncondensable gas on the thermal-hydraulic behavior of thecoolant of the primary circuit of a nuclear reactor in the VVER-440 geometry inabnormal situations. First, steam condensation with the presence of air was studied in the horizontal tubes of the steam generator (SG) of the PACTEL test facility. The French thermal-hydraulic CATHARE code was used to study the heat transfer between the primary and secondary side in conditions derived from preliminary experiments performed by VTT using PACTEL. In natural circulation and single-phase vapor conditions, the injection of a volume of air, equivalent to the totalvolume of the primary side of the SG at the entrance of the hot collector, did not stop the heat transfer from the primary to the secondary side. The calculated results indicate that air is located in the second half-length (from the mid-length of the tubes to the cold collector) in all the tubes of the steam generator The hot collector remained full of steam during the transient. Secondly, the potential release of the nitrogen gas dissolved in the water of the accumulators of the emergency core coolant system of the Loviisa nuclear power plant (NPP) was investigated. The author implemented a model of the dissolution and release ofnitrogen gas in the CATHARE code; the model created by the CATHARE developers. In collaboration with VTT, an analytical experiment was performed with some components of PACTEL to determine, in particular, the value of the release time constant of the nitrogen gas in the depressurization conditions representative of the small and intermediate break transients postulated for the Loviisa NPP. Such transients, with simplified operating procedures, were calculated using the modified CATHARE code for various values of the release time constant used in the dissolution and release model. For the small breaks, nitrogen gas is trapped in thecollectors of the SGs in rather large proportions. There, the levels oscillate until the actuation of the low-pressure injection pumps (LPIS) that refill the primary circuit. In the case of the intermediate breaks, most of the nitrogen gas is expelled at the break and almost no nitrogen gas is trapped in the SGs. In comparison with the cases calculated without taking into account the release of nitrogen gas, the start of the LPIS is delayed by between 1 and 1.75 h. Applicability of the obtained results to the real safety conditions must take into accountthe real operating procedures used in the nuclear power plant.

Tuning the design procedures for laser processed microwave mechanics

This research has been focused at the development of a tuned systematic design methodology, which gives the best performance in a computer aided environment and utilises a cross-technological approach, specially tested with and for laser processed microwave mechanics. A tuned design process scheme is also presented. Because of the currently large production volumes of microwave and radio frequency mechanics even slight improvements of design methodologies or manufacturing technologies would give reasonable possibilities for cost reduction. The typical number of required iteration cycles could be reduced to one fifth of normal. The research area dealing with the methodologies is divided firstly into a function-oriented, a performance-oriented or a manufacturability-oriented product design. Alternatively various approaches can be developed for a customer-oriented, a quality-oriented, a cost-oriented or an organisation-oriented design. However, the real need for improvements is between these two extremes. This means that the effective methodology for the designers should not be too limited (like in the performance-oriented design) or too general (like in the organisation-oriented design), but it should, include the context of the design environment. This is the area where the current research is focused. To test the developed tuned design methodology for laser processing (TDMLP) and the tuned optimising algorithm for laser processing (TOLP), seven different industrial product applications for microwave mechanics have been designed, CAD-modelled and manufactured by using laser in small production series. To verify that the performance of these products meets the required level and to ensure the objectiveness ofthe results extensive laboratory tests were used for all designed prototypes. As an example a Ku-band horn antenna can be laser processed from steel in 2 minutes at the same time obtaining a comparable electrical performance of classical aluminium units or the residual resistance of a laser joint in steel could be limited to 72 milliohmia.

On-Line Analytical Processing of Inventory Turnover

Operatiivisen tiedon tuottaminen loppukäyttäjille analyyttistä tarkastelua silmällä pitäen aiheuttaa ongelmia useille yrityksille. Diplomityö pyrkii ratkaisemaan ko. ongelman Teleste Oyj:ssä. Työ on jaettu kolmeen pääkappaleeseen. Kappale 2 selkiyttää On-Line Analytical Processing (OLAP)- käsitteen. Kappale 3 esittelee muutamia OLAP-tuotteiden valmistajia ja heidän arkkitehtuurejaan sekä tyypillisten sovellusalueiden lisäksi huomioon otettavia asioita OLAP käyttöönoton yhteydessä. Kappale 4, tuo esille varsinaisen ratkaisun. Teknisellä arkkitehtuurilla on merkittävä asema ratkaisun rakenteen kannalta. Tässä on sovellettu Microsoft:n tietovarasto kehysrakennetta. Kappaleen 4 edetessä, tapahtumakäsittelytieto muutetaan informaatioksi ja edelleen loppukäyttäjien tiedoksi. Loppukäyttäjät varustetaan tehokkaalla ja tosiaikaisella analysointityökalulla moniulotteisessa ympäristössä. Vaikka kiertonopeus otetaan työssä sovellusesimerkiksi, työ ei pyri löytämään optimaalista tasoa Telesten varastoille. Siitä huolimatta eräitä parannusehdotuksia mainitaan.

Analytical Study on the Influence of Geometrical Parameters on the Fatigue Strength of Welds with Undercuts

The purpose of this study is to analyze the influence of geometric parameters on the fatigue strength of the welded joint. The thesis includes the analytical study pertaining to variation of undercut and the weld toe radius. The theoretical part includes the concepts of fracture mechanics, different stages of the crack propagation and finally the results. The numerical results are obtained from FRANC2D/L. The results show that the fatigue strength of the welded structure depends on the parameters of the welds such as the weld toe radius, weld angle, height of the undercut and plate thickness. The results show that the fatigue life can be improved by having the undercut as minimum as possible. However there has been significant variation on the fatigue life of the structure when the weld toe radius is increased.

Eddy-current losses in rotor surface mounted permanent magnets

The aim of the work is to study the existing analytical calculation procedures found in literature to calculate the eddy-current losses in surface mounted permanent magnets within PMSM application. The most promising algorithms are implemented with MATLAB software under the dimensional data of LUT prototype machine. In addition finite elements analyze, utilized with help of Flux 2D software from Cedrat Ltd, is applied to calculate the eddy-current losses in permanent magnets. The results obtained from analytical methods are compared with numerical results.