Integrating testcase generator into Eclipse environment

Tämädiplomityö tutkii kuinka Eclipse -ympäristöä voidaan käyttää testitapausten generoinnissa. Eräs diplomityön pääaiheista on tutkia voidaanko olemassa olevilla Eclipsen komponenteilla parantaa symboolitietoutta, jotta testitapausten generointiin saataisiin lisää tietoa. Aluksi diplomityö antaa lyhyen katsauksen ohjelmistojentestaukseen, jotta lukija ymmärtää mitä ohjelmistotekniikan osa-aluetta diplomityö käsittelee. Tämän jälkeen kerrotaan lisää tietoa itse testitapausten generointiprosessista. Kun perusteet on käsitelty, tutustetaan lukija Eclipse -ympäristöön, mikä se on, mistä se koostuu ja mitä sillä voidaan tehdä. Tarkempaa tietoa kerrotaan Eclipsen komponenteista joita voidaan käyttää apuna testitapausten generoinnissa. Integrointi esimerkkinä diplomityössä esitellään valmiin testitapausgeneraattorin integrointi Eclipse -ympäristöön. Lopuksi Eclipse -pohjaista ratkaisua verrataan symboolitietouden sekä ajoajan kannalta aikaisempaan ratkaisuun. Diplomityön tuloksena syntyi prototyyppi jonka avulla todistettiin, että Eclipse - ympäristöön on mahdollista integroida testitapausgeneraattori ja että se voi lisätä symboolitietoutta. Tämätietouden lisäys kuitenkin lisäsi myös tarvittavaa ajoaikaa, joissakintapauksissa jopa merkittävästi. Samalla todettiin, että tällä hetkellä on menossa projekteja joiden tarkoituksena on parantaa käytettyjen Eclipse komponenttien suorituskykyä ja että tämä voi parantaa tuloksia tulevaisuudessa.

Automated Software Testing in Machine Automation

The problem of software (SW) defaults is becoming more and more topical because of increasing amount of the SW and its complication. The majority of these defaults are founded during the test part that consumes about 40-50% of the development efforts. Test automation allows reducing the cost of this process and increasing testing effectiveness. In the middle of 1980 the first tools for automated testing appeared and the automated process was implemented in different kinds of SW testing. In short time, it became obviously, automated testing can cause many problems such as increasing product cost, decreasing reliability and even project fail. This thesis describes automated testing process, its concept, lists main problems, and gives an algorithm for automated test tools selection. Also this work presents an overview of the main automated test tools for embedded systems.

ContinuousMultimodal Global Optimization with Differential Evolution-Based Methods

Metaheuristic methods have become increasingly popular approaches in solving global optimization problems. From a practical viewpoint, it is often desirable to perform multimodal optimization which, enables the search of more than one optimal solution to the task at hand. Population-based metaheuristic methods offer a natural basis for multimodal optimization. The topic has received increasing interest especially in the evolutionary computation community. Several niching approaches have been suggested to allow multimodal optimization using evolutionary algorithms. Most global optimization approaches, including metaheuristics, contain global and local search phases. The requirement to locate several optima sets additional requirements for the design of algorithms to be effective in both respects in the context of multimodal optimization. In this thesis, several different multimodal optimization algorithms are studied in regard to how their implementation in the global and local search phases affect their performance in different problems. The study concentrates especially on variations of the Differential Evolution algorithm and their capabilities in multimodal optimization. To separate the global and local search search phases, three multimodal optimization algorithms are proposed, two of which hybridize the Differential Evolution with a local search method. As the theoretical background behind the operation of metaheuristics is not generally thoroughly understood, the research relies heavily on experimental studies in finding out the properties of different approaches. To achieve reliable experimental information, the experimental environment must be carefully chosen to contain appropriate and adequately varying problems. The available selection of multimodal test problems is, however, rather limited, and no general framework exists. As a part of this thesis, such a framework for generating tunable test functions for evaluating different methods of multimodal optimization experimentally is provided and used for testing the algorithms. The results demonstrate that an efficient local phase is essential for creating efficient multimodal optimization algorithms. Adding a suitable global phase has the potential to boost the performance significantly, but the weak local phase may invalidate the advantages gained from the global phase.

Optimisation of data analysis method for a fluidized bed combustion test rig

Nowadays the used fuel variety in power boilers is widening and new boiler constructions and running models have to be developed. This research and development is done in small pilot plants where more faster analyse about the boiler mass and heat balance is needed to be able to find and do the right decisions already during the test run. The barrier on determining boiler balance during test runs is the long process of chemical analyses of collected input and outputmatter samples. The present work is concentrating on finding a way to determinethe boiler balance without chemical analyses and optimise the test rig to get the best possible accuracy for heat and mass balance of the boiler. The purpose of this work was to create an automatic boiler balance calculation method for 4 MW CFB/BFB pilot boiler of Kvaerner Pulping Oy located in Messukylä in Tampere. The calculation was created in the data management computer of pilot plants automation system. The calculation is made in Microsoft Excel environment, which gives a good base and functions for handling large databases and calculations without any delicate programming. The automation system in pilot plant was reconstructed und updated by Metso Automation Oy during year 2001 and the new system MetsoDNA has good data management properties, which is necessary for big calculations as boiler balance calculation. Two possible methods for calculating boiler balance during test run were found. Either the fuel flow is determined, which is usedto calculate the boiler's mass balance, or the unburned carbon loss is estimated and the mass balance of the boiler is calculated on the basis of boiler's heat balance. Both of the methods have their own weaknesses, so they were constructed parallel in the calculation and the decision of the used method was left to user. User also needs to define the used fuels and some solid mass flowsthat aren't measured automatically by the automation system. With sensitivity analysis was found that the most essential values for accurate boiler balance determination are flue gas oxygen content, the boiler's measured heat output and lower heating value of the fuel. The theoretical part of this work concentrates in the error management of these measurements and analyses and on measurement accuracy and boiler balance calculation in theory. The empirical part of this work concentrates on the creation of the balance calculation for the boiler in issue and on describing the work environment.

Code Generator for Key Management Protocols - Design and Implementation

Key management has a fundamental role in secure communications. Designing and testing of key management protocols is tricky. These protocols must work flawlessly despite of any abuse. The main objective of this work was to design and implement a tool that helps to specify the protocol and makes it possible to test the protocol while it is still under development. This tool generates compile-ready java code from a key management protocol model. A modelling method for these protocols, which uses Unified Modeling Language (UML) was also developed. The protocol is modelled, exported as an XMI and read by the code generator tool. The code generator generates java code that is immediately executable with a test software after compilation.

Modelling of the PWR PACTEL vertical steam generator with the TRACE code

The behavior of the nuclear power plants must be known in all operational situations. Thermal hydraulics computer applications are used to simulate the behavior of the plants. The computer applications must be validated before they can be used reliably. The simulation results are compared against the experimental results. In this thesis a model of the PWR PACTEL steam generator was prepared with the TRAC/RELAP Advanced Computational Engine computer application. The simulation results can be compared against the results of the Advanced Process Simulator analysis software in future. Development of the model of the PWR PACTEL vertical steam generator is introduced in this thesis. Loss of feedwater transient simulation examples were carried out with the model.