Kalsinaattorin siirtymien ja teräskuoren murtumien tutkiminen

Sementti on yksi eniten maailmassa käytetty rakennusmateriaali ja Suomessa sementin valmistuksesta vastaa Finnsementti Oy kahden tehtaan voimin. Lappeenrannan tehtaalle investoitiin uusi uunilinja vuonna 2007, joka on aikansa kehittyneintä tekniikkaa. Järjes-telmän esilämmitysvaiheen laitteissa, erityisesti kalsinaattorissa, on esiintynyt luvattoman paljon plastisoitumista ja murtumia. Tässä työssä tutkittiin lämpötilan ja sen vaihtelun vaikutusta järjestelmässä syntyneisiin siirtymiin ja murtumiin. Työn alussa luotiin katsaus erilaisiin murtumisilmiöihin ja niiden syntyyn. Vuorauksessa käytettyihin tiilien käyttäytymistä tutkittiin myös, koska ne ovat olennainen osa esilämmi-tysjärjestelmää. Työn kokeellisessa osuudessa aluksi määriteltiin järjestelmässä käytetylle teräkselle lujuusominaisuudet tutkimalla mikrorakennetta sekä suorittamalla veto- että kovuuskokeet materiaalille. Toisessa osiossa mitattiin järjestelmän alasajon aikana tapah-tuneet siirtymät. Laskennallisessa osuudessa tutkittiin väsymismurtuman mahdollisuutta sekä määritettiin kuoressa esiintyvän särön vaikutusta puhkeamis- ja murtumiskuormituk-seen. FEM- analyysissä tarkasteltiin lämpötilan vaikutusta siirtymien suuruuksiin ja pyrittiin löytämään perusteluita, miksi rakenne on todellisuudessa siirtynyt eri suuntiin kuin alun perin oli tarkoitettu. Lisäksi analysoitiin FEM- mallit tiilihyllystä ja kalsinaattorin kuoren tukikehästä, joista tutkittiin lämpökuorman aiheuttamia jännityksiä. Materiaalin osalta selvisi, että kyseessä oli hyvin yleinen rakenneteräs S235 tai sitä vas-taava teräslaatu. Teräs ei ominaisuuksiltaan sovellu kuumiin olosuhteisiin, jonka vuoksi järjestelmässä käytettävän eristevuorauksen kunto on erityisen tärkeä rakenteen käyttöiän kannalta. Vuorauksen kunnosta riippuu, kuinka suuren lämpökuorman teräskuori saa. Väsymismurtuman mahdollisuus jäi minimaalisen pieneksi lämpötilan muutoksen vaiku-tuksesta. Analysoinnin tulosten perusteella voitiin todeta, että lämpötilan hitaasti mutta kohtalaisen suurella vaihteluvälillä sekä tiilien turpoamisen vaikutuksella on erittäin suuri merkitys järjestelmässä esiintyviin murtumiin.

Climate driven changes in temperature, pH and food quality : effects on copepod reproduction

Increased emissions of greenhouse gases into the atmosphere are causing an anthropogenic climate change. The resulting global warming challenges the ability of organisms to adapt to the new temperature conditions. However, warming is not the only major threat. In marine environments, dissolution of carbon dioxide from the atmosphere causes a decrease in surface water pH, the so called ocean acidification. The temperature and acidification effects can interact, and create even larger problems for the marine flora and fauna than either of the effects would cause alone. I have used Baltic calanoid copepods (crustacean zooplankton) as my research object and studied their growth and stress responses using climate predictions projected for the next century. I have studied both direct temperature and pH effects on copepods, and indirect effects via their food: the changing phytoplankton spring bloom composition and toxic cyanobacterium. The main aims of my thesis were: 1) to find out how warming and acidification combined with a toxic cyanobacterium affect copepod reproductive success (egg production, egg viability, egg hatching success, offspring development) and oxidative balance (antioxidant capacity, oxidative damage), and 2) to reveal the possible food quality effects of spring phytoplankton bloom composition dominated by diatoms or dinoflagellates on reproducing copepods (egg production, egg hatching, RNA:DNA ratio). The two copepod genera used, Acartia sp. and Eurytemora affinis are the dominating mesozooplankton taxa (0.2 – 2 mm) in my study area the Gulf of Finland. The 20°C temperature seems to be within the tolerance limits of Acartia spp., because copepods can adapt to the temperature phenotypically by adjusting their body size. Copepods are also able to tolerate a pH decrease of 0.4 from present values, but the combination of warm water and decreased pH causes problems for them. In my studies, the copepod oxidative balance was negatively influenced by the interaction of these two environmental factors, and egg and nauplii production were lower at 20°C and lower pH, than at 20°C and ambient pH. However, presence of toxic cyanobacterium Nodularia spumigena improved the copepod oxidative balance and helped to resist the environmental stress, in question. In addition, adaptive maternal effects seem to be an important adaptation mechanism in a changing environment, but it depends on the condition of the female copepod and her diet how much she can invest in her offspring. I did not find systematic food quality difference between diatoms and dinoflagellates. There are both good and bad diatom and dinoflagellate species. Instead, the dominating species in the phytoplankton bloom composition has a central role in determining the food quality, although copepods aim at obtaining as a balanced diet as possible by foraging on several species. If the dominating species is of poor quality it can cause stress when ingested, or lead to non-optimal foraging if rejected. My thesis demonstrates that climate change induced water temperature and pH changes can cause problems to Baltic Sea copepod communities. However, their resilience depends substantially on their diet, and therefore the response of phytoplankton to the environmental changes. As copepods are an important link in pelagic food webs, their future success can have far reaching consequences, for example on fish stocks.

Bumblebees in a Changing Climate: Evaluating the Effects of Temperature on Queen Performance

Bumblebees are a very essential group of pollinating insects, but their populations have declined drastically during the past decades. We need to understand why their numbers are decreasing and what can be done to reverse this trend. Climate change-related phenomena, such as changes in the overwintering temperatures and spring conditions, are among the most prominent threats to bumblebees. Queens have a special role in the lifecycle of bumblebees because they overwinter and start new colonies the next year. Their successful performance: survival, overwintering ability, longevity, immune competence, and nest establishing capability in spring, is highly important for bumblebee populations. However, the effects of climate change on bumblebee queen performance remain unknown. The main objective of this thesis was to assess how temperature affects the performance of bumblebee queens during and after overwintering. The effects of warm temperature predicted by climate change scenarios on queen survival and stress-tolerance were studied by a four-month artificial diapause of bumblebee queens at two temperatures (9°C and 1.8°C). Bumblebee colonies were also reared in a laboratory and factors affecting colony characteristics were examined. In addition, queen performance during spring was studied in a starvation experiment using two temperatures (15°C as normal; 24°C as warmer than average) and queens collected from nature right after their emergence. My research revealed how temperature affects queen performance, and queen size was found to be an important factor determining the direction of some of these effects. We found a 0.4g weight threshold for bumblebee queens to be able to survive overwintering. In addition, during mild winters, larger queens have a higher chance than smaller ones to survive through winter and also to cope with immunological stresses after overwintering. During cold conditions, which are normal in the current climatic situation, this advantage disappears. In the spring starvation experiment, the starved queens survived approximately eight days longer in 15°C than in 24°C, which means that starvation risk rises significantly with increasing spring temperature, in a situation where food is scarce due to for example frost damage or asynchrony between bumblebees and their important food plants. These results could mean that in the future climate, larger queens are better able to survive the winter, initiate their nests and start rearing their offspring. This may be problematic, because I also detected two alternative strategies of colony development that differ between large and small queens; larger queens start to lay eggs earlier at nest initiation, their colonies mature later, they produce more workers, and they have a more strongly male biased sex allocation compared with smaller queens. If larger queens have a greater change of producing offspring after a mild winter, this could lead to a significant decline in the total production of new queens at a population level. Thus, it seems that queen size could act as one mechanism regulating the population level outcomes in different temperatures. The new information presented in my thesis reinforces that basic research, monitoring, and local species conservation of bumblebees both in Finland and globally must be increased to ensure that this highly important pollinator group survives in the face of climate change.

Factors affecting the usability of aspen (Populus tremula) wood dried at different temperature levels

In this dissertation the main aim was to study the usability of aspen wood in the mechanical wood processes, especially the factors that affect the usability of aspen wood, which is dried at different temperature levels. The problematic of varying temperatures from level to another seem to have significant effects on distortions. According to the studies conducted, many practical solutions for drying of aspen timber can be made. European aspen sawn timber should be dried in relatively narrow widths, short lengths, edged and sawn pith free. The results achieved give an interesting view for the distortions of aspen wood between HT drying and heat treatment. The most significant result is that cupping seems to decrease when increasing temperature level from HT drying to heat treatment phase. The difference is significant. Other very obvious result is that bow and crook are increasing between these two temperature levels, bow significantly. Also the modelling gives a good background for this result since cupping is reduced by higher temperatures. It can also be assumed that these distortions can be affected for example by sorting out the timber used to different moisture levels before drying. This could be a very simple solution for practical purposes. From practical point of view, it was also noted during the drying tests performed that the discoloration seem to be no problem for aspen boards dried in temperatures under 150 °C. Altogether, this dissertation covers many interesting points of view of factors affecting distortions of wood in different temperature stages. Aspen as species in use of mechanical wood industries seems to be a species suitable for component production. According to the results, the best yield from aspen timber can be achieved in industry that can utilize relatively short components of sawn wood. Results achieved give a significant indication about the factors affecting distortions of wood at different temperature stages of drying, especially considering European aspen.

Effects of interband and intraband impurity scattering on coherence length in the pnictide superconductors

After discovery of cuprates, a search for new high temperature superconducting families began and it led to the discovery of layered pnictide compounds with critical temperatures limited up to ∼56 K. Pnictides consist elements from Group V of Periodic Table (nitrogen, phosphorus, arsenic, antimony and bismuth). In this work coherence length h in mixed state of pnictide superconductors is calculated numerically. In calculation is taken into account interband and intraband impurity scattering in framework of quasiclassical Eilenberger theory for s± pairing symmetry. Differences between Ginzburg-Landau and Eilenberger theories is shown and the comparison with existing models is done.

Effects of interband and intraband impurity scattering on coherence length in the pnictide superconductors

After discovery of cuprates, a search for new high temperature superconducting families began and it led to the discovery of layered pnictide compounds with critical temperatures limited up to ~56 K. Pnictides consist elements from Group V of Periodic Table (nitrogen, phosphorus, arsenic, antimony and bismuth). In this work coherence length ξh in mixed state of pnictide superconductors is calculated numerically. In calculation is taken into account interband and intraband impurity scattering in framework of quasiclassical Eilenberger theory for s± pairing symmetry. Differences between Ginzburg-Landau and Eilenberger theories is shown and the comparison with existing models is done.

Galvanomagnetic effects in InGaAs nanostructure

Investigation of galvanomagnetic effects in nanostructure GaAs/Mn/GaAs/In0.15Ga0.85As/ GaAs is presented. This nanostructure is classified as diluted magnetic semiconductor (DMS). Temperature dependence of transverse magnetoresistivity of the sample was studied. The anomalous Hall effect was detected and subtracted from the total Hall component. Special attention was paid to the measurements of Shubnikov-de Haas oscillations, which exists only in the case of magnetic field aligned perpendicularly to the plane of the sample. This confirms two-dimensional character of the hole energy spectrum in the quantum well. Such important characteristics as cyclotron mass, the Fermi energy and the Dingle temperature were calculated, using experimental data of Shubnikov-de Haas oscillations. The hole concentration and hole mobility in the quantum well also were estimated for the sample. At 4.2 K spin splitting of the maxima of transverse resistivity was observed and g-factor was calculated for that case. The values of the Dingle temperatures were obtained by two different approaches. From the comparison of these values it was concluded that the broadening of Landau levels in the investigated structure is mainly defined by the scattering of charge carriers on the defects of the crystal lattice

Modeling of temperature regimes in a furnace of bubbling fluidized bed boiler

The work is mainly focused on the technology of bubbling fluidized bed combustion. Heat transfer and hydrodynamics of the process were examined in the work in detail. Special emphasis was placed on the process of heat exchange in a freeboard zone of bubbling fluidized bed boiler. Operating mode of bubbling fluidized bed boiler depends on many parameters. To assess the influence of some parameters on a temperature regime inside the furnace a simplified method of zonal modeling was used in the work. Thus, effects of bed material fineness, excess air ratio and changes in boiler load were studied. Besides the technology of combustion in bubbling fluidized bed, other common technologies of solid fuels combustion were reviewed. In addition, brief survey of most widely used types of solid fuel was performed in the work.

Finite size effects in superconducting nanocomposites

The present Master’s thesis presents theoretical description of the extraodinary behavior of the confined Indium nanoparticles. Superconducting properties of nanoparticles and nanocomposites are extensively reviewed. Special attention has been paid to phase fluctuation, shell and disordered effects. The experimental data has been obtained and provided by Dmitry Shamshur from Ioffe Physical Technical Institute. The investigated material represents a highly ordered system of silicate spheres filled with indium metal, where the In nanoparticles are interconnected between each other. Bulk indium is a superconductor with crititcal superconducting temperature Tc0 = 3:41 K. But indium nanoparticles exhibit different behavior, the critical temperature rise by approximately 20% up to 4.15 K. As well as transition of the indium particles to type-II superconductivity with high critical magnetic fields. Such diversity is explained by finite size effects which originate from nanosize of the samples.

Effects of Fin Parameters on Gas-Side Heat Transfer Performance of H-Type Finned Tube Bundle in a Waste Heat Recovery Boiler

Alfa Laval Aalborg Oy designs and manufactures waste heat recovery systems utilizing extended surfaces. The waste heat recovery boiler considered in this thesis is a water-tube boiler where exhaust gas is used as the convective heat transfer medium and water or steam flowing inside the tubes is subject to cross-flow. This thesis aims to contribute to the design of waste heat recovery boiler unit by developing a numerical model of the H-type finned tube bundle currently used by Alfa Laval Aalborg Oy to evaluate the gas-side heat transfer performance. The main objective is to identify weaknesses and potential areas of development in the current H-type finned tube design. In addition, numerical simulations for a total of 15 cases with varying geometric parameters are conducted to investigate the heat transfer and pressure drop performance dependent on H-type fin geometry. The investigated geometric parameters include fin width and height, fin spacing, and fin thickness. Comparison between single and double tube type configuration is also conducted. Based on the simulation results, the local heat transfer and flow behaviour of the H-type finned tube is presented including boundary layer development between the fins, the formation of recirculation zone behind the tubes, and the local variations of flow velocity and temperature within the tube bundle and on the fin surface. Moreover, an evaluation of the effects of various fin parameters on heat transfer and pressure drop performance of H-type finned tube bundle has been provided. It was concluded that from the studied parameters fin spacing and fin width had the most significant effect on tube bundle performance and the effect of fin thickness was the least important. Furthermore, the results suggested that the heat transfer performance would increase due to enhanced turbulence if the current double tube configuration is replaced with single tube configuration, but further investigation and experimental measurements are required in order to validate the results.