Synteesikaasun liukoisuus ja aineensiirto fermentointiliuokseen

Työssä tutkittiin synteesikaasun komponenttien: hiilimonoksidin, vedyn ja hiilidioksidin liukoisuutta ja aineensiirtonopeutta fermentointiliuokseen. Kirjallisuusosassa käsitellään kaasujen liukoisuuksiin ja kaasu-nesteaineensiirtoon vaikuttavia tekijöitä ja esitellään korrelaatioita, jotka on kehitetty volumetrisen aineensiirtokertoimen ennustamiseen sekoitetussa fermentorissa. Kirjallisuus-osassa esitetään myös synteesikaasun komponenttien liukoisuudet veteen, etanoliin ja etikkahappoon 37 ºC lämpötilassa ja esitellään Flowbat-simulointiohjelman MHV2-mallin käyttöä kaasu-neste tasapainojen mallin-nuksessa. Työn kokeellisessa osassa tutkittiin synteesikaasun komponenttien liukoisuuksia veteen ja kasvatusalustaan sekä kehitettiin mittausmenetelmä kaasu-neste tasapainojen mittaukseen. Tasapainomittauksissa tutkittiin etanolin ja etikkahapon konsentraatioiden vaikutusta synteesikaasun liukoisuuteen. Lisäksi mallinnettiin kaasu-neste tasapainoja monikomponenttisysteemeissä MHV2-mallin avulla. Kokeellisen osan aineensiirtomittauksissa tutkittiin sekoitusnopeuden ja kaasun volumetrisen syöttönopeuden vaikutusta hiilimonoksidin ja vedyn volumetriseen aineensiirtokertoimeen kLa kahden litran tilavuuksisessa laboratoriofermentorissa. Mittaustulosten perusteella kasvatusalustan komponentit vaikuttavat merkittävästi hiilidioksidin liukoisuuteen. Lisäys etanolin ja etikkahapon konsentraatioissa parantaa hiilimonoksidin liukoisuutta kasvatusalustaan. Kaasun volumetrinen syöttönopeus ja sekoitusnopeus vaikuttavat voimakkaasti volumetrisen aineensiirtokertoimen arvoon. Tutkitussa systeemissä korkein teoreettinen solutiheys, joka voitiin saavuttaa suurimmalla hiilimonoksidin aineensiirto-nopeudella, oli 3 g/L. Tämä on kaksinkertainen verrattuna aiemmissa VTT:n kokeissa saavutettuihin solutiheyksiin.

Ultrafine grinding of FGD and phosphogypsum with an attrition bead mill and a jet mill : optimisation and modelling of grinding and mill comparison

Fine powders of minerals are used commonly in the paper and paint industry, and for ceramics. Research for utilizing of different waste materials in these applications is environmentally important. In this work, the ultrafine grinding of two waste gypsum materials, namely FGD (Flue Gas Desulphurisation) gypsum and phosphogypsum from a phosphoric acid plant, with the attrition bead mill and with the jet mill has been studied. The ' objective of this research was to test the suitability of the attrition bead mill and of the jet mill to produce gypsum powders with a particle size of a few microns. The grinding conditions were optimised by studying the influences of different operational grinding parameters on the grinding rate and on the energy consumption of the process in order to achieve a product fineness such as that required in the paper industry with as low energy consumption as possible. Based on experimental results, the most influential parameters in the attrition grinding were found to be the bead size, the stirrer type, and the stirring speed. The best conditions, based on the product fineness and specific energy consumption of grinding, for the attrition grinding process is to grind the material with small grinding beads and a high rotational speed of the stirrer. Also, by using some suitable grinding additive, a finer product is achieved with a lower energy consumption. In jet mill grinding the most influential parameters were the feed rate, the volumetric flow rate of the grinding air, and the height of the internal classification tube. The optimised condition for the jet is to grind with a small feed rate and with a large rate of volumetric flow rate of grinding air when the inside tube is low. The finer product with a larger rate of production was achieved with the attrition bead mill than with the jet mill, thus the attrition grinding is better for the ultrafine grinding of gypsum than the jet grinding. Finally the suitability of the population balance model for simulation of grinding processes has been studied with different S , B , and C functions. A new S function for the modelling of an attrition mill and a new C function for the modelling of a jet mill were developed. The suitability of the selected models with the developed grinding functions was tested by curve fitting the particle size distributions of the grinding products and then comparing the fitted size distributions to the measured particle sizes. According to the simulation results, the models are suitable for the estimation and simulation of the studied grinding processes.

Carponate precipitation with carbon dioxide gas

The aim of this thesis research work focused on the carbonate precipitation of magnesium using magnesium hydroxide Mg(OH)2 and carbon dioxide (CO2) gas at ambient temperature and pressure. The rate of dissolution of Mg(OH)2 and precipitation kinetics were investigated under different operating conditions. The conductivity and pH of the solution were inline monitored by a Consort meter and the solid samples gotten from the precipitation reaction were analysed by a laser diffraction analyzer Malvern Mastersizer to obtain particle size distributions (PSD) of crystal samples. Also the Mg2+ concentration profiles were determined from the liquid phase of the precipitate by ion chromatography (IC) analysis. Crystal morphology of the obtained precipitates were also investigated and discussed in this work. For the carbonation reaction of magnesium hydroxide in the present work, it was found that magnesium carbonate trihydrate (nesquehonite) was the main product and its formation occurred at a pH of around 7-8. The stirrer speed has a significant effect on the dissolution rate of Mg(OH)2. The highest obtained Mg2+ concentration level was 0.424 mol L-l for the 470 rpm and 0.387 mol L-1 for the 560 rpm which corresponded to the processing time of 45 mins and 40 mins respectively. The particle size distribution shows that the average particle size keeps increasing during the reaction as the CO2 is been fed to the system. The carbonation process is kinetically favored and simple as nesquehonite formation occurs in a very short time. It is a thermodynamically and chemically stable solid product, which allows for a long-term storage of CO2. Since the carbonation reaction is a complex system which includes dissolution of magnesium hydroxide particles, absorption of CO2, chemical reaction and crystallization, the dissolution of magnesium hydroxide was studied in hydrochloric acid (HCl) solvent with and without nitrogen (N2) inert gas. It was found on the dissolution part that the impeller speed had effect on the dissolution rate. The higher the impeller speed the higher the pH of the solution, although for the highest speed of 650rpm it was not the case. Therefore, it was concluded that the optimum speed of the stirrer was 560rpm. The influence of inert gas N2 on the dissolution rate of Mg(OH)2 particles could be seen based on measured pH, electric conductivity and Mg2+ concentration curves.

Jauhatusparametrien vaikutus jauhatustuotteen partikkelikokoon ja suodattuvuuteen

Tämän diplomityön tarkoituksena on tutkia ensin jauhatusparametrien vaikutus rikastushiekan hienousasteeseen eli miten partikkelikokojakaumaa kuvaavat partikkelikoot muuttuvat. Tämän jälkeen tutkitaan miten rikastushiekan hienousasteen muuttuminen vaikuttaa jauhettujen rikastushiekkalietenäytteiden suodattuvuuteen. Partikkelikokojakauman variaatioista yritetään löytää yhteys suodinkakun ominaisvastuksen ja huokoisuuden välillä. Jauhatus suoritettiin laboratoriomittakaavan helmimyllyllä märkäjauhatuksena. Jauhatusta varten tehtiin kolmitasoinen faktorikoesuunnitelma, jossa muuttujina ovat lasihelmien halkaisija, jauhatusaika ja sekoitinelimen pyörimisnopeus. Suodatus toteutettiin vakiopainesuodatuksena kolmella eri suodatuspaineella Nutsche-suodattimella. Työn tuloksista saatiin selville, että partikkelikokojakauman leveys korreloi suodinkakun ominaisvastuksen kanssa. Kun partikkelikokojakauma leveys muuttui kapeammaksi, saatiin kakun ominaisvastus pienemmäksi ja suodatukseen kulunut aika lyheni. Kapein partikkelikokojakauman leveys saatiin suurimmalla helmen halkaisijalla, pisimmällä jauhatusajalla sekä suurimmalla sekoitusnopeudella.