The Possibility of Greenhouse Gas Mitigation in Ethiopian Cement Industry

Cement industry significantly associated with high greenhouse gas (GHG) emissions. Considering the environmental impact, particularly global warming potential, it is important to reduce these emissions to air. The aim of the study is to investigate the mitigation possibility of GHG emissions in Ethiopian cement industry. Life cycle assessment (LCA) method used to identify and quantify GHG emissions during one ton of ordinary portland cement (OPC) production. Three mitigation scenarios: alternative fuel use, clinker substitution and thermal energy efficiency were applied on a representative gate-to-gate flow model developed with GaBi 6 software. The results of the study indicate that clinker substitution and alternative fuel use play a great role for GHG emissions mitigation with affordable cost. Applying most energy efficient kiln technology, which in turn reduces the amount of thermal energy use, has the least GHG emissions reduction intensity and high implementation cost comparing to the other scenarios. It was found that the cumulative GHG emissions mitigation potential along with other selected mitigation scenarios can be at least 48.9% per ton of cement production.

Teollisuusjätteen käyttö kiinteytys-stabiloinnin sideaineena ja haitta-aineiden stabiloinnin tehostamisessa

Tässä kanditaatintyössä selvitettiin kuinka erilaiset sideaineseokset soveltuvat raskas-metallien sitomiseen 28 vuorokautta stabiloiduissa näytteistä. Työssä oletettiin teollisten jätefraktioiden käytön tehostavan eräiden metallien, kuten kupari ja sinkki, immobilisointia lievästi pilaantuneista maa-aineksista. Kokeellisessa osassa stabiloitiin Kokkolan satamasta ruopattua sedimenttiä, jonka sinkkipitoisuudet olivat ylittäneet saastuneen sedimentin ohjearvon (≥400 mg/kg). Sedimenttiin lisättiin eri sideaineseoksia ja näytteiden annettiin stabiloitua 28 vuorokautta, minkä jälkeen niistä testattiin liukenevat raskasmetallit muokatulla ravistelutestillä. Eri sideaineseoksilla saatuja tuloksia verrattiin pelkän yleissementin käyttöön. Lisäksi erillisistä näytteistä otettiin pyyhkäisyelektronimikros-koopilla (SEM) kuvia havainnollistamaan stabiloitumista. Näissä näytteissä käytettiin samoja sideaineita kuin tehdyissä kokeissa. Liukoisuustestien tuloksista voidaan huomata näytteissä ongelmalliseksi raskasmetalliksi identifioidun sinkin sitoutuvan parhaiten sementin ja kipsin sekoituksella. Myös tuhkaa sisältävät sideainesekoitukset pienensivät sinkin liukoisuutta verrattuna pelkkään yleis-sementtiin. Jatkotutkimuksissa voitaisiin testata erilaisia sideainesekoituksia betonira-kentamisessa, joilla saadaan ainakin 25 MPa lujuusarvo, pilaantunutta sedimenttiä tai maa-ainesta käyttäen.

Bonding of Composite Resin to Alumina and Zirconia Ceramics with Special Emphasis on Surface Conditioning and Use of Coupling Agents

Dental oxide ceramics have been inspired by their biocompability and mechanical properties which have made durable all-ceramic structures possible. Clinical longevity of the prosthetic structures is dependent on effective bonding with luting cements. As the initial shear bond strength values can be comparable with several materials and procedures, long-term durability is affected by ageing. Aims of the current study were: to measure the shear bond strength of resin composite-to-ceramics and to evaluate the longevity of the bond; to analyze factors affecting the bond, with special emphasis on: the form of silicatization of the ceramic surface; form of silanization; type of resin primer and the effect of the type of the resin composite luting cement; the effect of ageing in water was studied regarding its effect to the endurance of the bond. Ceramic substrates were alumina and yttrium stabilized zirconia. Ceramic conditioning methods included tribochemical silicatization and use of two silane couplings agents. A commercial silane primer was used as a control silane. Various combinations of conditioning methods, primers and resin cements were tested. Bond strengths were measured by shear bond strength method. The longevity of the bond was generally studied by thermocycling the materials in water. Additionally, in one of the studies thermal cycling was compared with long-term water storaging. Results were analysed statistically with ANOVA and Weibull analysis. Tribochemical treatment utilizing air pressure of 150 kPa resulted shear bond strengths of 11.2 MPa to 18.4 MPa and air pressure of 450 kPa 18.2 MPa to 30.5 MPa, respectively. Thermocycling of 8000 cycles or four years water storaging both decreased shear bond strength values to a range of 3.8 MPa to 7.2 MPa whereas initial situation varied from 16.8. Mpa to 23.0 MPa. The silane used in studies had no statistical significance. The use of primers without 10-MDP resulted spontaneous debonding during thermocycling or shear bond strengths below 5 MPa. As conclusion, the results showed superior long-term bonding with primers containing 10-MDP. Silicatization with silanizing showed improved initial shear bond strength values which considerably decreased with ageing in water. Thermal cycling and water storing for up to four years played the major role in reduction of bond strength, which could be due to thermal fatigue of the bonding interface and hydrolytic degradation of the silane coupled interface.

Monolithic zirconium dioxide as a full contour restorative material: With special emphasis on the optical and mechanical properties

Full contour monolithic zirconia restorations have shown an increased popularity in the dental field over the recent years, owing to its mechanical and acceptable optical properties. However, many features of the restoration are yet to be researched and supported by clinical studies to confirm its place among the other indirect restorative materials This series of in vitro studies aimed at evaluating and comparing the optical and mechanical properties, light cure irradiance, and cement polymerization of multiple monolithic zirconia material at variable thicknesses, environments, treatments, and stabilization. Five different monolithic zirconia materials, four of which were partially stabilized and one fully stabilized were investigated. The optical properties in terms of surface gloss, translucency parameter, and contrast ratio were determined via a reflection spectrophotometer at variable thicknesses, coloring, sintering method, and after immersion in an acidic environment. Light cure irradiance and radiant exposure were quantified through the specimens at variable thicknesses and the degree of conversion of two dual-cure cements was determined via Fourier Transform Infrared spectroscopy. Bi-axial flexural strength was evaluated to compare between the partially and fully stabilized zirconia prepared using different coloring and sintering methods. Surface characterization was performed using a scanning electron microscope and a spinning disk confocal microscope. The surface gloss and translucency of the zirconia investigated were brand and thickness dependent with the translucency values decreasing as the thickness increased. Staining decreased the translucency of the zirconia and enhanced surface gloss as well as the flexural strength of the fully stabilized zirconia but had no effect on partially stabilized zirconia. Immersion in a corrosive acid increased surface gloss and decreased the translucency of some zirconia brands. Zirconia thickness was inversely related to the amount of light irradiance, radiant exposure, and degree of monomer conversion. Type of sintering furnace had no effect on the optical and mechanical properties of zirconia. Monolithic zirconia maybe classified as a semi-translucent material that is well influenced by the thickness, limiting its use in the esthetic zones. Conventional acid-base reaction, autopolymerizing and dual-cure cements are recommended for its cementation. Its desirable mechanical properties give it a high potential as a restoration for posterior teeth. However, close monitoring with controlled clinical studies must be determined before any definite clinical recommendations can be drawn.

The discourse on political pluralism in early eighteenth-century England : a conceptual study with special reference to terminology of religious origin

Doctoral dissertation, University of Jyväskylä

Properties of slow-release phosphorus fertilizers with special references to their use on drained peatland forests : A review

Tiivistelmä: Hidasliukoisten fosforilannoitteiden ominaisuudet ja käyttökelpoisuus suometsien lannoituksessa. Kirjallisuuteen perustuva tarkastelu